2. Place cables
in the J-hook.
1. Install the
nVent CADDY CAT12
support clip.
The nVent CADDY CAT12 is equipped with a bend back
tab to provide contact free containment for
sensitive high performance cables.
3. (Optional) Using
pliers bend top
portion of hook
back at slot.
Load
Fig 12
Fig 8
Pre-Riveted Factory Assemblies
Fig 14
Fig 10
Fig 11
Fig 6 Fig 7
Fig 1 Fig 2 Fig 3
Fig 16
Fig 15
Fig 13
Fig 9
Fig 4 Fig 5
For use with Data Communication Cables only.
The nVent CADDY CAT12 support clip holds 4-pair UTP cables: 16 Cat.5/5e or 16 fiber optic
cables or 10 Cat.6.
Provides strain relief and routes cables so bend radius conforms to EIA/TIA-568-A standard.
Complies with UL,cUL, and NEC requirements for structured cabling systems.
Complies with 1997 EIA/TIA 569-A.
R
Note: Do not exceed recommended cable
quantities per fastener
Part Number
Article
Number
Fig.
Description
CAT12AF14
181840 1
1/16" [2] thru 1/4" [6] Z Purlin
CAT12VF14
181800 2
1/16" [2] thru 1/4" [6] vertical flange
CAT124Z34 181240
3
#12 thru 1/4" [6] wire, plain or threaded rod
& 1/8" [3] thru 3/8" [10] flange
CAT126Z34 181270
3/8" [10] plain ot threaded rod & 3/8" [10]
thru 9/16" [10] flange
CAT128Z34
N/A
1/2" [13] & 5/8" [16] threaded rod
CAT12AB
181900 4
Angle Bracket
CAT12CPNA
N/A
16
Angle bracket with pin driven mounting
hole
CAT12BC
N/A
6
1/8" [3] thru 1/2" [13] flange
CAT12BCB
N/A
7
1/8" [3] thru 1/2" [13] flange, rotates 360
CAT12BC200B
181430 8
1/8" [3] thru 5/8" [16] flange, rotates 360
CAT12BC200
181400 9
1/8" [3] thru 5/8" [16] flange
CAT12TS
181200 10
Support from Tee Grid
CAT1224
181650
11
1/8" [3] thru 1/4" [6] flange, bottom mount
rotates 360
CAT1258
181660
5/16" [8] thru 1/2" [13] flange, bottom
mount rotates 360
CAT12912
181670
1/2" thru 3/4" flange, bottom mount rotates
360
CAT1224SM
181510
12
1/8" [3] thru 1/4" [6] flange
CAT1258SM
181520
5/16" [8] thru 1/2" [13] flange
CAT12912SM
181530
1/2" [13] thru 3/4" [19] B1 flange
CAT12
181100 13
Hold 4-pair UTP cables: 16 Cat. 5/5e or 16
fiber optic cables or 10 Cat. 6
CATTS
181170 14
Support from Tee Grid
CAT12CD1B
181950 15
J-Hook to 3/4" & 1" round or square
pedestal
CAT12AFAB3
N/A
5
Angle bracket with pin driven mounting
hole
TECHNICAL SUPPORT:
www.nVent.com
CFS246_N
INSTRUCTION SHEET
1 OF 4
© 1997-2019 nVent All Rights Reserved
WARNING:
nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at
1.
www.nVent.com
and from your nVent customer service representative.
nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be
completely
followed to ensure proper and safe installation and performance.
3.
Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property
4.
damage, serious bodily injury and/or death, and void your warranty.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
5.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
6.
other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified
engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are
owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the
right to change specifications without prior notice.
