OBaby Astrid User manual

Designed in the UK
IMPORTANT
KEEP FOR FUTURE REFERENCE
Instructions
Astrid
Version: R1-0-1
Mini Cot Bed

obaby.co.uk
ThankyufrchsingbeparfheObayfamily
Our Cot Bed conrms to BS EN 716-1:2017 and BS 8509:2008 + A1:2011. To ensure that your
cot bed is used in accordance with these instructions, please read them fully.
Your child’s safety may be affected if you do not follow these instructions.
WARNING: A child’s safety is your responsibility.
WARNING: Assembly should be carried out by a competent adult only.
WARNING: Do not use more than one mattress in the cot bed.
WARNING: Do not place this child’s bed near heat sources, windows and other furniture.
WARNING: Be aware of the risk of open re and other sources of heat, such as electric bar
res, gas res, etc in the near vicinity of the cot bed.
WARNING: Do not use this child’s bed if any part is broken, torn or missing.
WARNING: Do not leave anything in the cot bed or place the cot bed close to another
product, which could provide a foothold or present a danger of suffocation or
strangulation, e.g. strings, blinds/curtain cords etc.
• This product is intended for use from birth up to 4 years old.
• Please be aware that the lowest base position is the safest and the base should always be
used in that position as soon as the baby is old enough to sit unaided.
• The thickness of the mattress chosen should be such that the internal height (surface of the
mattress to the upper edge of the cot frame) is at least 500mm when the base is set in the
lowest position and a minimum of 200mm when the cot base is set in the highest position.
• We recommend you use the Obaby Mattress Size 120 x 60 cm for this cot bed. The mattress
should be no more then 30mm shorter or narrower than the internal length or width of the
cot bed.
• Regularly check that all ttings and compnents of the cot/bed are fully tightened and in
working order.
• To prevent injury from falls, as soon as the child is able to climb out of the cot, it should be
changed into the bed mode for use up until 4 years of age.
• The cot bed is designed to be dismantled for storage or transportation.
• Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should
not be placed next to other furniture or windows, and should be placed either tight to the
wall or have a gap of 300mm between the wall and the side of the bed.
• All assembly ttings should be tightened properly and care should be taken to ensure that
no screws are loose, as a child could trap parts of the body, or clothing (e.g. ribbons, draw-
strings, necklaces) this could lead to strangulation.
• During assembly children should be kept away from the product due to possible risk of inju-
ry.
• Wood is a natural material, the colour will darken with age.
• Use only spare parts approved by the manufacturer.
Routine care & maintenance
Safety Warnings

obaby.co.uk
For cleaning, use only a mild detergent and warm water.
◊ DO NOT USE BLEACH
◊ DO NOT USE any abrasive substances.
◊ From time to time, check your cot for loose screws, and worn parts. Replace or adjust the
parts as needed.
Due to constant updating and improvments, some components may occasionally differ slightly
from the images shown in these instructions. We reserve the rights to change the specications
of any products without prior notice. If you need any assistance please contact your Obaby
retailer from whom you purchased your product, who will take appropriate action.
Dnfrgeleaveareviewnur
TrusPilPagex
Care & Maintenance

obaby.co.uk
You will require a cross head screw driver
Parts List
P1P1
x8x8
40m40mmm
P2P2
x8x8
P3P3
x4x4
P4P4
x4x4
P5P5
x4x4
P6P6
x35x35
P7P7
x8x8
P8P8
x12x12
P9P9
x4x4
P1P100
x1x1
P11P11
x1x1
P12P12
x12x12
P13P13
x12x12
P14P14
x2x2
AA
FF
BB
EE
DD
DD
EE
HH
CC
GG
CC
II
II
JJ
HH
FF

obaby.co.uk
Stage 1
Assembly
Stage 2
P9 xP9 x 44
P7P7 P7P7
P6P6
P6P6
P6P6
P6P6
P6P6
P6P6
P8P8
P8P8
P8P8
P8P8
P2P2
P2P2
HH
II

obaby.co.uk
Assembly
Stage 3
Stage 4
CC
CC
DD
DD
P6P6
P6P6
P6P6
P6P6
P1P1
P1P1
P1P1
P1P1

obaby.co.uk
Assembly
Stage 5
Stage 6
P12P12
P12P12
P2P2
P2P2 P2P2
P2P2
P12P12
P12P12
P12P12
P12P12
P12P12
P12P12
P5P5 P5P5
P5P5
P5P5
P12P12
P6P6
P6P6 P6P6
P6P6
P12P12 P12P12
P12P12
AAAA
P1P133
P1P133
P6P6
P6P6
P6P6 P1P133
P1P133
P1P133
P1P133
FF
EE

obaby.co.uk
Assembly
Stage 7
Use a cross head screw driver to tighten
P13 tting
AA
FF
P1P1
P1P1
33
33

obaby.co.uk
Assembly
Stage 8
Stage 9
GG
P1P1
P1P1
P1P1
P1P1
x4x4
GG
P4P4
P3P3

obaby.co.uk
Assembly
Stage 10

obaby.co.uk
Converting into a Day Bed
Stage 1
Stage 2
P1P1
P1P1
P1P1
P1P1

obaby.co.uk
Converting into a Day Bed
Stage 4
Stage 3
AA
P12P12
P12P12
BB
EE
FF
AA
EE
BB
P12P12
P14P14
P6P6
P1P111
P8P8
P8P8
P8P8
GG

obaby.co.uk
Converting into a Day Bed
Stage 6
Stage 5
Tighted up P8 ttings with cross head screw driver
EE
JJ
P8P8
BB
P1P133
P13P13
P1P133

obaby.co.uk
Converting into a Day Bed
Stage 8
Stage 7
AA
P8P8
P13P13
P1P1P1P1

obaby.co.uk
Notes
Stage 10
Stage 9
GG
P3P3
P4P4

obabyuk
obaby.co.uk
obabyuk