Ofs Tilly User manual

Tilly assembly instructions

2ofs.com imagine a place® 800.521.5381 Assembly instructions
Tilly assembly instructions
Table of contents
Safety instructions 3
Light features 4
Freestanding base installation 5
Clamp mount installation 6
Surface mount installation 7

3ofs.com imagine a place® 800.521.5381 Assembly instructions
Tilly assembly instructions
Important safety instructions
When using an electrical furnishing, basic precautions should always be followed, including
the following:
This furnishing is made for commercial use only.
Read all instructions before using this furnishing:
DANGER
To reduce the risk of electrical shock:
1. Always unplug this furnishing from the electrical outlet before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids,
or disabled persons.
3. Use the furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped in water. Return the furnishing
to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Use only SJT 18 AWG cord.
8. Risk of injury. Maximum load 75 pounds.
To reduce the risk of electric shock, this furnishing has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
Note – servicing is only to be performed by an authorized representative.
Servicing of double-insulated products
In a double-insulated product, two systems of insulation are provided instead of
grounding. No grounding means is provided on a double-insulated product, nor is a
means for grounding to be added to the product. Servicing a double-insulated product
requires extreme care and knowledge of the system, and is to be done only by qualified
service personnel. Replacement parts for a double-insulated product must be identical to
the parts they replace. A double-insulated product is marked with the words “DOUBLE
INSULATION” OR “DOUBLE INSULATED”. The symbol (square within a square) is also
able to be marked on the product.
Save these instructions

4ofs.com imagine a place® 800.521.5381 Assembly instructions
Tilly assembly instructions
Light features
Occupancy sensor
The under-head integrated Passive Infrared (PIR) occupancy sensor automatically turns the fixture
o after 30 minutes of no detection. Coverage: 360° lens view, 90° outward detection angle,
coverage of 30° diameter at 15” distance.
Auto turn-o
The standard version with no occupancy sensor will automatically turn o after 10 hours (+/- 15
minutes).
Touch-and-hold dimming
Any level of output can be achieved to fit user preferences, from 100% to 15% light output, with a
touch and hold of the finger on the slightly raised touch-sensitive button under the head. When
desired level is reached, release the button. On/o is toggled with a single touch.
USB port (available on freestanding base only)
Charging available with optional Type-A connector (5V, 1.2A) USB port built in to the base for
charging your mobile devices (Figure A). Insert your USB cable into the port, and power is
available.
Figure A
USB port

5ofs.com imagine a place® 800.521.5381 Assembly instructions
Tilly assembly instructions
1. Remove fixture from packaging.
2. Stand fixture upright.
3. Connect silver quick-connect cord to power supply. (Figure A)
Figure A
Freestanding base
Assembly:

6ofs.com imagine a place® 800.521.5381 Assembly instructions
Tilly assembly instructions
Assembly:
1. Turn the adjustment screw out to allow for a space larger than the thickness of the work
surface.
2. Position the clamp bracket onto the work surface in the desired location and tighten the
adjustment screw. Make sure there is a gap between the back edge of the surface and the
wall or panel of approximately ½” to allow for the power plug connector to pass through.
(Figure A)
3. Connect silver quick-connect cord to power supply. (Figure B)
Clamp mount
Figure A
Adjustment screw
Quick-connect cord
Figure B

7ofs.com imagine a place® 800.521.5381 Assembly instructions
Tilly assembly instructions
Tools required:
2-⅛“ Diameter hole saw
Phillips head screwdriver
1. Drill a 2-⅛” hole in the work surface.
2. Install surface mount base in hole, ensuring anti-rotation stop is located appropriately for the
intended orientation.
3. The surface mount base will be pre-attached to the light fixture, so the limits of the base
rotation can be determined by rotating the base by hand (Figure A)
4. Feed the fixture’s power cord through the holes in surface mount and work surface.
5. Fasten the surface mount bracket using a Phillips head screwdriver by loosely installing the 3
screws provided through the lower washer in the bottom of the surface mount bracket.
6. Before fully tightening the lower screws, ensure that the light rotates over the desired area.
7. Connect silver quick-connect cord to power supply. (Figure B)
Surface mount
Figure A
Mount bracket
Mount base
Power cord
Figure B
Assembly: