Okina USA License Plate Capture Series Quick start guide

SHT-7540LPDN_rev031309
6
3
2
1
0
7
5
4
SHT-7540LPDN
SHT-7540LPDNP
Operational Manual
License Plate Capture Series
License Plate Capture Day & Night Camera
z1/3” Sony Super HAD CCD II
zSony HQ-1 DSP
z540 TV Lines
z0.08 Lux @ F1.0
zBuilt-in Auto Sens-up
zHigh Gain/Low Noise Amplifier - DNR
zAdvanced 8-step Manual Shutter
zCAR-DC Iris Control is available to achieve reliable
license plate recognition for road surveillance when car
speed is up to 120km/hr in the daytime and 70km/hr at
night time.
zDual Power 12V DC / 24V AC
1Lens Mount
This mount is used to install a CS-mount lens.
CS-adaptor ring is required if using a C mount lens.
2CS Mount Fixing Screw
Screw for fixing mount and adjusting back focus if needed.
3Mount Adaptor
This adaptor can be attached to either the top or bottom of
unit.
4Auto Iris Lens Connector (4-pin type)
The lens connector supplies the auto-iris lens (not supplied)
with DC power and a video signal or DC control signal.
5ME/AES Shutter Control
(0)1/100 (120) sec. (1) FL: 1/130 sec.
(2) 1/160 sec. (3) 1/210 sec.
(4) 1/280 sec. (5) 1/360 sec.
(6) 1/420 sec. (7) 1/560 sec.
Camera to object moving speed
Shutter
Speed 15~20M (45~60ft) 20~35M (60~100ft) 35~60M (100~180ft)
1/210sec 30~60 Km/hr 45~75 Km/hr
1/280sec 35~65 Km/hr 55~85 Km/hr
1/360sec 45~75 Km/hr 65~95 Km/hr
1/420sec 50~80 Km/hr 80~100 Km/hr 80~100 Km/hr
1/560sec 60~90 Km/hr 90~105 Km/hr 90~105 Km/hr
*The table above is only for reference. Values may change
due to the angle of the camera and the installation location.
6Control Switch
SW1. BLC: Backlight Compensation OFF/BLC switch
SW2. Day/Night Mode: D/N / Color switch
SW3. AGC: Automatic Gain Control AGC/S.AGC switch
SW4. Sync Mode: Sync Mode Selection L.L/INT switch
PIN NO. VIDEO DC
1 DC + 12V CONTROL -
2 NC CONTROL +
3 VIDEO SIG DRIVE +
4 GND DRIVE -
FEATURES
Please read the Operational Manual
before attempting to use this product.
PARTS AND FUNCTIONS
DIMEN
S
I
O
N
S
(U
ni
t
: mm
)
P = PAL Version
12V DC / 24V AC 90V~260V AC

SHT-7540LPDN_rev031309
7Video Connector
This is an output for connecting to a video monitor or recorder
etc. (75 Ω).
8Auto Iris Mode Selection Switch
For switching the output from the auto iris connector. Shutter
speed is fixed at 1/100(120) sec. when switch is set to DC or
VIDEO position.
DC: To be set when using a non-amp auto iris lens.
CAR-DC: To be set when using for license plate capture. (Car
speed is up to 120km/hr in the daytime and 70km/hr at night).
VIDEO: To be set when using an auto iris lens with built-in
amp.
9V.P. (Vertical Phase) Adjustor
This is used to adjust the vertical phase of the video output
signal
Power Input Terminal
Connect the power supply of 12V DC or 24V AC.
○
11 Power Input Terminal
Connect the power supply of 90V~260V AC.
SW1. BLC (Back Light Compensation) Mode Switch
When strong light is present behind the object being
photographed, the object will appear dark. In this case, turn on
the BLC.
SW2. D/N (Day & Night) Mode Switch
D/N: Day & Night mode turns on at night time.
Color: Color mode stays on at all times.
S.A.G.C./A.G.C. Mode Switch
S.A.G.C.: When camera has installed at low light condition. The
sensitivity of the camera rises (26dB).
A.G.C.: 6dB
In order to activate D/N function (Color mode automatically
switches to B/W mode under 2 Lux), please switch to S.AGC.
SYNC Mode Switch
L.L. MODE: It synchronizes the video signal between cameras
using the frequency of the power supply without external
synchronous generator.
INT MODE: The camera maybe operated independently with the
internal crystal control.
For Road Surveillance: Car speed is up to 120km/hr in the
daytime and 70km/hr at night.
1. ME/AES Shutter Control should be set on “2”. (Please
refer to the function ○
5ME/AES Shutter Control).
2. Auto Iris Mode should be switched to “CAR-DC” mode.
3. Control Switch should be set as following:
For Highway Surveillance:
1. ME/AES Shutter Control should be set on “3” or “4”.
(Please refer to the function ○
5ME/AES Shutter
Control).
2. Auto Iris Mode should be switched to “VIDEO” or “DC”
mode.
3. Control Switch should be set as following:
For Normal Surveillance:
1. ME/AES Shutter Control should be set to “0”. (Please
refer to the function ○
5ME/AES Shutter Control).
2. Auto Iris Mode should be switched to “VIDEO” or “DC”
mode.
3. Control Switch should be set as following:
CONTROL SWITCH OPERATION
CONTROL SWITCH SETTING

SHT-7540LPDN_rev031309
Model SHT-7540LPDN SHT-7540LPDNP
TV System NTSC PAL
Image Sensor 1/3” Sony Super HAD CCD II
DSP Sony HQ-1
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Video Output 1.0Vp-p Composite / 75ohms
Resolution 540 TV Lines
Minimum
Illumination
0.08 Lux @ F1.0
Color mode automatically switches
to B/W mode under 2 Lux
Infrared
Sensitivity 700~1100nm
Electronic
Shutter Speed
AES ON, AES OFF, 1/100(120)sec,
FL:1/130sec,1/160sec,1/210sec,
1/280sec, 1/360sec, 1/420sec, 1/560sec
Back Light
Compensation ON/OFF Switchable
Auto Gain
Control ON/OFF Switchable
Day/Night D/N / COLOR Switchable
DNR / Sens-up High Gain/Low Noise Amplifier
Scan System 2:1 Interlace
Synchronization Internal/Line Lock (AC Version Only)
S/N Ratio More than 50dB (S.AGC OFF)
Auto Iris Control Video / DC Switchable
Auto White
Balance AWB
Lens Mount CS/C (with adaptor)
Power 12V DC / 24V AC, 3.0W
90~260V AC, 4.5W
Operation
Temperature 14oF ~ 122oF / -10oC ~ 50oC
Storage
Humidity RH 80% or less
Storage
Temperature -4oF ~ 140oF / -20oC ~ 60oC
Dimension 4.72”(L) x 2.36”(W) x 1.97”(H)
120mm(L) x 60mm(W) x 50mm(H)
Weight 0.88 lbs / 400g
*Specifications are subject to change without notice
zOne (1) SHT-7540LPDN/SHT-7540LPDNP Camera
zOne (1) Operational Manual
*For any returns, please include all components listed above with
original packaging in Resalable Condition. Absolutely No Returns
will be accepted if any component is missing/damaged or if any cable is
cut or tampered with.
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this
may damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling
could damage the camera.
3. Requires a proper operating environment
This camera is designed for outdoor or indoor use. The allowable
temperature range for operation of this camera is between 14°F ~
122°F / -10°C ~ 50°C and the allowable humidity is 80%RH
maximum.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned
before lens installation or whenever the lens is changed.
Cleaning should be done by using a chamois, a very fine soft
cloth, lens tissue, or cotton tipped applicator and ethanol to
carefully remove any fingerprint or dust.
5. Check the power source voltage
The power source voltage should be within the specified range.
(Camera must meet the specifications). Camera must be
connected to a surge protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may
touch dangerous voltage points of short out parts that could
result in a fire or electric shock. Never spill any kind of liquid on
the video product.
7. Servicing
Do not attempt to service this video product by yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all service to qualified servicing
personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service
to qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
video product.
c. If the video product has been dropped or the cabinet has
been damaged.
d. When the video product exhibits a distinct change in
performance.
OKINA USA products are covered under warranty for one year from
the date of purchase. The warranty will automatically be voided if
any of the following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm
any information regarding when and where the product was
purchased. We have no other way to verify the purchase record
without the serial number on the camera sticker; therefore, it
should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner
not described in this manual, the warranty will be voided
immediately. It is the customer’s responsibility to keep the
camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered
with. Cutting or modifying of the cables will result in termination
of the warranty.
CAUTION
WARRANTY
SPECIFICATIONS
PA
C
KA
G
E
CO
NTENT
S