Okina USA LPC Series Quick start guide

Copyright © 2009. All Rights Reserved. P = PAL Version
www.okinausa.com REV092909
6
3
2
1
0
7
5
4
SHM-7540LPDN-IO
SHM-7540LPDN-IOP
Operational Manual
License Plate Capture Series
License Plate Capture Day & Night Camera
z1/3” Sony Super HAD CCD II
zSony HQ-1 DSP, 540 TVL
z0.08 Lux @ F1.0
zI/O Input/Output
zMechanical IR Cut Filter (ICR)
zBuilt-in Auto Sens-up
zHigh Gain/Low Noise Amplifier - DNR
zAdvanced 8-step Manual Shutter
zCAR-DC Iris Control is available to achieve reliable license
plate recognition for road surveillance when car speed is up
to 90 mi/hr (150km/hr) in the daytime and 90 mi/hr
(150km/hr) at night time with external IR LEDs.
zDual Power 12V DC / 24V AC
1Lens Mount
This mount is used to install a CS mount lens.
CS adaptor ring is required if using a C mount lens.
2CS Mount Fixing Screw
Screw for fixing mount and adjusting back focus if needed.
3Mount Adaptor
This adaptor can be attached to either the top or bottom of unit.
4Auto Iris Lens Connector (4-pin type)
The lens connector supplies the auto-iris lens (not supplied) with
DC power and a video signal or DC control signal.
5ME/AES Shutter Control
(0) 1/100 (120) sec. (1) 1/190 sec.
(2) 1/350 sec. (3) 1/610 sec.
(4) 1/1120 sec. (5) 1/2000 sec.
(6) 1/3240 sec. (7) 1/4000 sec.
Camera to object moving speed
Shutter
Speed 45~60ft
(15~20m) 60~100ft (20~35m) 100~180ft (35~60m)
1/100 sec
1/190 sec
1/350 sec
1/610 sec 15~35 mi/h
r
(30~60 Km/hr) 45~45 mi/h
r
(45~75 Km/hr)
1/1120 sec 20~40 mi/h
r
(35~65 Km/hr) 35~53 mi/h
r
(55~85 Km/hr)
1/2000 sec 25~45 mi/h
r
(45~75 Km/hr) 40~60 mi/h
r
(65~95 Km/hr)
1/3240 sec 30~50 mi
/
h
r
(50~80 Km/hr) 50~62 mi/h
r
(80~100 Km/hr) 50~62 mi/h
r
(80~100 Km/hr)
1/4000 sec 35~55 mi/h
r
(60~90 Km/hr) 55~65 mi/h
r
(90~105 Km/hr) 55~65 mi/h
r
(90~105 Km/hr)
*The table above is only for reference. Values may change due to the angle
of the camera and the installation location.
6Control Switch
SW1. BLC: Backlight Compensation OFF/BLC switch
SW2. Day/Night Mode: D/N / Color switch
SW3. AGC: Automatic Gain Control AGC/S.AGC switch
SW4. Sync Mode: Sync Mode Selection L.L/INT switch
7Video Connector
Output for connecting to a video monitor or recorder.
8Auto Iris Mode Selection Switch
For switching the output from the auto iris connector. Shutter
speed is fixed at 1/100(120) sec. when switch is set to DC or
VIDEO position.
DC: To be set when using a auto iris lens. Be sure to
adjust proper DC level for D&N operation.
CAR-DC: To be set when using for license plate
capture. (Car speed is up to 90 mi/hr (150 km/hr) in the daytime
and 90 mi/hr (150 km/hr) at night with external IR LEDs).
VIDEO: To be set when using an auto iris lens with built-in amp.
FEATURES
Please read the Operational Manual
before attempting to use this product.
PARTS
A
ND FUNCTIONS
DIMEN
S
I
O
N
S
(U
ni
t
: mm
)
Note: Do Not Remove Screws

Copyright © 2009. All Rights Reserved. P = PAL Version
www.okinausa.com REV092909
9V.P. (Vertical Phase) Adjustor
Used to adjust the vertical phase of the video output signal
Power Input Terminal
Connect the power supply of 12V DC or 24V AC.
SW1. BLC (Back Light Compensation) Mode Switch
When strong light is present behind the object being photographed,
the object will appear dark. In this case, turn on the BLC.
SW2. D/N (Day & Night) Mode Switch
D/N: Day & Night mode turns on at night time.
Color: Color mode stays on at all times.
S.A.G.C./A.G.C. Mode Switch
S.A.G.C.: When camera has installed at low light condition. The
sensitivity of the camera rises (26dB).
A.G.C.: 26dB
In order to activate D/N function (Color mode automatically
switches to B/W mode under 2 Lux), please switch to S.AGC.
SYNC Mode Switch
L.L. MODE: It synchronizes the video signal between cameras
using the frequency of the power supply without external
synchronous generator.
INT MODE: The camera maybe operated independently with the
internal crystal control.
For Road Surveillance: Car speed is up to 90 mi/hr (150 km/hr) in
the daytime and 90 mi/hr (150 km/hr) at night.
1. ME/AES Shutter Control should be set on “2”. (Please refer to
the function ○
5ME/AES Shutter Control).
2. Auto Iris Mode should be switched to “CAR-DC” mode.
3. Control Switch should be set as following:
For Highway Surveillance:
1. ME/AES Shutter Control should be set on “3” or “4”.
(Please refer to ○
5ME/AES Shutter Control).
2. Auto Iris Mode should be switched to “VIDEO” or “DC”.
3. Control Switch should be set as following:
Model SHM-7540LPDN-IO SHM-7540LPDN-IOP
TV System NTSC PAL
Image Sensor 1/3” Sony Super HAD CCD II
DSP Sony HQ-1
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Video Output 1.0Vp-p Composite / 75ohms
Resolution 540 TV Lines
Minimum
Illumination 0.08 Lux @ F1.0
IR Sensitivity 700~1100nm
Mechanical IR
Cut Filter (ICR) External controlled by D&N IO; Color (IN: 0V or normal open) / D&N (In: 5~12V DC or normal close)
Electronic
Shutter Speed
AES: 1/50(60) sec ~ 1/100,1000 sec
(0) 1/100(120) sec (1) 1/190 sec
(2) 1/350 sec (3) 1/610 sec
(4) 1/1120 sec (5) 1/2000 sec
(6) 1/3240 sec (7) 1/4000 sec
Intelligent
Shutter Speed
Capturing license plate for vehicle speeds up to
90 mi/hr (150 km/hr) in the daytime and 90 mi/hr
(150 km/hr) at night with external IR LEDs
Back Light
Compensation ON/OFF Switchable
Auto Gain
Control AGC / Super AGC
Auto White
Balance AWB
Day/Night Mechanical IR Cut Filter (ICR)
D/N / COLOR Switchable
I/O Yes
DNR / Sens-up Automatic; High Gain/Low Noise Amplifier
Scan System 2:1 Interlace
Synchronization Internal/Line Lock (AC Version Only)
S/N Ratio More than 50dB (S.AGC OFF)
Adjustment VR DC Level, L.L. V-phase
Automatic IRIS ;
Connector Video/DC ; D4 IRIS Jack
Lens Mount CS/C (with adaptor)
Power Supply 12V DC / 24V AC
Power
Consumption 3.0W
Operation
Temperature 14°F ~ 122°F / -10oC ~ 50oC
Storage
Humidity RH 80% or less
Storage
Temperature -4oF ~ 140oF / -20oC ~ 60oC
Dimension 4.72”(L) x 2.36”(W) x 1.97”(H)
120mm(L) x 60mm(W) x 50mm(H)
Weight 0.88 lbs / 400g
*Specifications are subject to change without notice
SPECIFICATIONS
CONTROL SWITCH OPERATION
CONTROL SWITCH SETTING

Copyright © 2009. All Rights Reserved. P = PAL Version
www.okinausa.com REV092909
zOne (1) SHM-7540LPDN-IO/SHM-7540LPDN-IOP Camera
zOne (1) Operational Manual
*For any returns, please include all components listed above with
original packaging in Resalable Condition. Absolutely No Returns
will be accepted if any component is missing/damaged or if any cable is
cut or tampered with.
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this
may damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling
could damage the camera.
3. Requires a proper operating environment
This camera is designed for outdoor or indoor use. The allowable
temperature range for operation of this camera is between 14°F ~
122°F / -10°C ~ 50°C.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned
before lens installation or whenever the lens is changed. Cleaning
should be done by using a chamois, a very fine soft cloth, lens
tissue, or cotton tipped applicator and ethanol to carefully remove
any fingerprint or dust.
5. Check the power source voltage
The power source voltage should be within the specified range.
(Camera must meet the specifications). Camera must be connected
to a surge protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch
dangerous voltage points of short out parts that could result in a fire
or electric shock. Never spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all service to qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service to
qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video
product.
c. If the video product has been dropped or the cabinet has been
damaged.
d. When the video product exhibits a distinct change in
performance.
OKINA USA products are covered under warranty for one year from
the date of purchase. The warranty will automatically be voided if
any of the following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm
any information regarding when and where the product was
purchased. We have no other way to verify the purchase record
without the serial number on the camera sticker; therefore, it
should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner
not described in this manual, the warranty will be voided
immediately. It is the customer’s responsibility to keep the
camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered
with. Cutting or modifying of the cables will result in termination
of the warranty.
CAUTION
WARRANTY
LI
S
T
O
F
CO
MP
O
NENT
S