Olicom Ethernet MCA 10/100 Adapter User manual

Guide to Operations
Ethernet MCA 10/100 Adapter
OC-2920/1.0

Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414
Ethernet MCA 10/100 Adapter
Guide to Operations

ii
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414
The Olicom clasped hands logo are trademarks of Olicom A/S.
Olicom is a registered trademark of Olicom A/S.
All other brands or product names are trademarks or registered trademarks of their respective holders.
Olicom A/S reserves the right to modify the information given in this publication without prior notice.
The warranty terms and conditions applicable for your purchase of this equipment are given at the time
of purchase. Consult your place of purchase for details.
Publication: OC-2920 v. 1.0. Part number: 710001414
© Copyright Olicom A/S, Denmark, April 1998
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying, recording or
otherwise, without the prior written permission of the publisher.
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. Thisequipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However,there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
•Consult the dealer or an experienced radio/television technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Modifications
If the device is changed or modified without the express approval of Olicom A/S the user may void his
or her authority to operate the equipment.
Declaration of Conformity
We Olicom A/S
Nybrovej 114
DK-2800 Lyngby
Denmark
declare under our sole responsibility that the product
Ethernet MCA 10/100 Adapter (OC-2335)
to which this declaration relates, is in conformity with the
following standards or other normative documents:
EN 50082-1
EN 55022
EN 60825-1
EN 60950
incl. amendments following the provisions of the 73/23/EEC and 89/336/EEC directives.

iii
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414
Table of Contents
1. Introduction 1
Disk Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Online Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Troubleshooting and getting Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Late-breaking News . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Notational Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Installation Overview 5
3. Hardware Installation 7
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Adapter Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting the Adapter Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
MCA Adapter Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. Windows 95 Express Installation 11
5. NetWare Client Express Installation
for DOS and Windows 3.1x 13
6. The Setup Program 15
Running the Setup Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7. Software Installation 17
Why Adapter Drivers? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Supported Environments and Drivers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Microsoft Windows 95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Multiple Adapter Configuration - Windows 95. . . . . . . . . . . . . . . . . . . . . . 18
Adapter Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
NDIS 3.0 Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Microsoft Windows NT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Windows NT 4.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Windows NT 3.5x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Adapter Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
NDIS 3.0 Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Microsoft Windows for Workgroups 3.11. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Install NDIS Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adapter Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Multiple Adapter Configuration (WfW 3.11). . . . . . . . . . . . . . . . . . . . . . . . 27
Microsoft Network Client 3.0 for DOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Novell NetWare Workstations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
NetWare DOS ODI Workstations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
NetWare Client 32 for Windows 95. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

iv
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414
NetWare Client 32 for Windows 3.1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
NetWare Client 32 for DOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
NetWare OS/2 Requester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Novell NetWare Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
NetWare 4.x Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
NetWare 3.12 Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
IBM DOS Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
IBM LAN Support Program (DOS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
IBM DOS LAN Services - DLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
IBM OS/2 Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
IBM NTS/2 and IBM Extended Services . . . . . . . . . . . . . . . . . . . . . . . . . . 43
IBM LAPS - LAN Server 3.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
IBM MPTS - LAN Server 4.0/5.0, OS/2 WARP . . . . . . . . . . . . . . . . . . . . . 44
Configuring the NDIS 2.0 MAC Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
NDIS 2.0 MAC Driver Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8. Utilities 47
Adapter Information for Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
9. Diagnostics 49
Running the Diagnostics Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Adapter Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Network Connection Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
10. Troubleshooting 51
Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
EMM386 Memory Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Everything has been tried! What now?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
11. Contacting Technical Support 55
Before You Contact Olicom Technical Support . . . . . . . . . . . . . . . . . . . . . . 55
Hotline Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Fax Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Bulletin Board Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Standard Modem Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
ISDN Modem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Internet E-Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Anonymous Internet FTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Internet World Wide Web Server (WWW). . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Olicom Support WEB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Problem Report Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

v
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414
Appendix A.System Requirements 61
Appendix B.Driver Messages 63
B.1 Microsoft/IBM NDIS 2.0 MAC Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Information messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
B.2 Microsoft NDIS 3.0 Miniport Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Windows 95. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Windows NT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
NDIS 3.0 Miniport Driver Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . 67
B.3 DOS ODI Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Common DOS ODI Errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Errors specific to the OCE3XODI.COM DOS ODI Driver . . . . . . . . . . . . . 69
B.4 OS/2 ODI Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
B.5 NetWare Server ODI Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
B.6 Diagnostics Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Appendix C.Abbreviations 75
Appendix D.Technical Information 77
Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Illustrations
Figure 1. Ethernet MCA 10/100 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2. MCA PC Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 3. Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 4. Opening Screen - NetWare Client Express Install . . . . . . . . . . . . . . . 13
Figure 5. Setup Start Screen - Windows 95 and Windows NT. . . . . . . . . . . . . . 15
Figure 6. Setup Start Screen - Windows 3.x and DOS. . . . . . . . . . . . . . . . . . . . 16
Figure 7. Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Figure 8. RJ-45 Connector Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Figure 9. Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Tables
Table 1. Problems and Solutions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

vi
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414
About this manual
Welcome to this manual and congratulations on selecting the Olicom Ethernet
MCA 10/100 Adapter.
This Guide to Operations is directed towards users without prior knowledge of
network adapter installation, and it provides the information required to perform a
standard installation of the Ethernet MCA 10/100 Adapter.
This guide contains 11 chapters and four appendices. Reading the sections that
deal with the environment in which your adapter will be used will ease installation
of the hardware and software described in this guide.
Chapter 1 is a general introduction to this manual.
Chapter 2 provides an installation overview.
Chapter 3 describes the physical installation (hardware).
Chapter 4 describes Windows 95 Express Installation.
Chapter 5 describes NetWare Client Express Installation.
Chapter 6 describes the Setup program.
Chapter 7 provides guidelines for installation of the adapter driver software in
different network environments.
Chapter 8 describes the utility programs.
Chapter 9 introduces the Diagnostics program.
Chapter 10 provides troubleshooting hints.
Chapter 11 tells how to contact Olicom Technical Support.
Appendix A lists the system requirements.
Appendix B contains error messages, return codes and suggested actions to
recover from an error condition.
Appendix C lists the used abbreviations.
Appendix D lists the technical specifications and certifications.
Expert users and end-users who require detailed technical information can obtain
this from the Olicom online documentation. See page 2 for details.
❏

1
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Introduction
1. Introduction
The Ethernet MCA 10/100 Adapter (OC-2335) is designed for computers
complying to the Micro Channel Architecture specification. The OC-2335 adapter
features easy installation, high frame transfer rates and low latency.
The adapter has a UTP RJ-45 connector for 100Base-TX and 10Base-T cabling
and includes software-detectable network speed, 10 or 100 Mbps.
Figure 1. Ethernet MCA 10/100 Adapter
All major Network Operating Systems are supported, and for standard operating
modes, no configuration input is required from the user.
Disk Backup
Before performing any task, make copies of all the Olicom disks and store the
originals in a safe place.
Use a diskcopy command, for example “DISKCOPY A: A:”.

2
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Introduction
Package Contents
The Olicom Ethernet MCA 10/100 Adapter package contains:
•One Ethernet MCA 10/100 Adapter (OC-2335) as shown in figure 1.
•Four disks:
Setup Disk containing installation, utilities and
documentation
NetWare Client Disk containing Novell NetWare
Client for DOS and MS Windows 3.x
Driver Disk containing network drivers
Diagnostics Disk containing adapter diagnostics
•This Guide to Operations, OC-2920
•One warranty card
Online Documentation
This Guide to Operations contains all the information required for a standard
adapter installation with default settings. However, if the installation is more
complex or more information is needed, Olicom’s online documentation provides
access to extensive information that complements what is given in this manual.
The online documentation is available under both DOS and Windows.
Insert the Setup Disk in drive “A” and run A:SETUP from DOS or Windows and
select “Help” or “Installation Overview”.
The Setup program is described in detail in chapter 6, The Setup Program.
Troubleshooting and getting Help
If the Olicom Ethernet MCA 10/100 Adapter should perform unexpectedly, see
chapter 10, Troubleshooting, chapter 9, Diagnostics or the Olicom online
documentation for guidelines. If you cannot solve the problem, see chapter 11,
Contacting Technical Support for technical assistance.
Late-breaking News
Additional information not available at the time of print is contained in the online
documentation: Late-breaking News.

3
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Introduction
Notational Conventions
“CAPITAL LETTERS” (Helvetica) indicates user input. You may use upper or
lower case letters when entering names and commands.
“
ESC
” (Helvetica narrow) indicates key entries, e.g.
CTRL
and
F1
.
Italics refer to another section, chapter or document.
“ h ” following a number indicates hexadecimal notation, for example 02AFh.
“ [ ] ” (square brackets) indicate an optional entry.
“ < > ” (angle brackets) indicate text to be substituted.
“ Courier typeface ” indicates screen display.
“ ❏” indicates the end of a chapter.
❏

4
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Introduction

5
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Installation Overview
2. Installation Overview
1. Install the adapter in the computer. Chapter 3, Hardware Installation, explains
this in detail.
2. The system automatically assigns configuration parameters. The MCA
parameters are determined by the machine-dependent setup program.
3. Install the adapter driver(s).
If you are using Windows 95, see Windows 95 Express Installation on page 11.
If you are using Novell NetWare, see the NetWare Client Express Installation
for DOS and Windows 3.1x on page 13.
Most major network operating systems (NOSs) or operating systems (OSs)
provide installation support for Olicom cards. However, if no procedures are
available - or manual driver installation is required - use chapter 7, Software
Installation and/or the Olicom online documentation as a guideline.
Installation of the Olicom Ethernet MCA 10/100 Adapter is now completed.
❏

6
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Installation Overview

7
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Hardware Installation
3. Hardware Installation
Overview
This section describes how to install the Ethernet MCA 10/100 Adapter in one of
the expansion slots in your computer. See the computer documentation for
additional information on installing expansion cards. The term “computer” is used
as a general term to include PCs, computers and computer systems.
➽Important: Static electricity can be destructive to sensitive components on the
adapter. Discharge yourself by touching a grounded unit before removing the
adapter from the anti-static packing bag.
Installation Requirements
•A medium-sized screwdriver
•The Operations Guide for your computer.
Adapter Installation
1. Switch all computer system components off and disconnect all main power
supply cables.
2. Place the peripheral units: keyboard, monitor, etc. away from the PC, and
position the PC itself to give yourself easy access to the back panel.
3. Remove the PC top cover to expose the
inside of the PC. See figure 2 for Micro
Channel Architecture (MCA-type)
computers.
4. The MCA 10/100 Adapter fits a 16- or 32-
bit MCA slot.
5. Loosen the thumbscrew that holds the
metal plate on the back panel
corresponding to the chosen slot.
6. If your computer has an additional plastic
cover on the back panel, pry it out
carefully with a screwdriver.
Figure 2. MCA PC Top View
MCA 10/100 Adapter
Thumbscrews Back panel
Front panel
MCA expansion slots

8
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Hardware Installation
7. Tilt the adapter to let the interface connector slip through the opening in the
back panel, and thenpress the edge connector firmly into the chosen expansion
slot. (Make sure that the end of the Ethernet MCA 10/100 Adapter fits into the
card guide at the front panel).
8. Secure the card with the thumbscrew from the previously-removed metal
bracket and replace the PC top cover.
Connecting the Adapter Cable
1. Insert the modular telephone jack in the RJ-45 connector. The jack is secured
and correctly inserted when you hear a click.
For 10 Mbps operation, a category 3, 4 or 5 cable is required.
For 100 Mbps operation, a category 5 cable is required.
➽Note: Make absolutely sure that you connect the adapter cable to the adapter you
have just installed. Connecting the cable to an expansion card other than the
Ethernet MCA 10/100 Adapter could result in serious damage to the expansion
card and/or the Ethernet Network.
Figure 3. Back Panel
2. Connect the other end of the cable to a wall outlet or a transceiver.
3. Make sure that the PC is turned off then re-connect the main power supply
cable.
4. Switch power on.

9
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Hardware Installation
MCA Adapter Configuration
1. Turn power off and insert disk in drive “A” the backup copy of the
REFERENCE/USER diskette that came with your computer.If you have not
yet made a backup copy of the REFERENCE/USER diskette, do so by
selecting the “BACKUP THE REFERENCE DISKETTE/COPY USER
DISKETTE” function from the MAIN MENU on the original diskette.
2. Turn power on to start the PC from the diskette and wait for the MAIN MENU
to appear.
➽Note: Do not at this stage choose to run an automatic configuration as you are
prompted to do!
3. Select the “COPY OPTION DISKETTE” function and follow the instructions.
4. When prompted for an option diskette, insert the Driver diskettethat came with
the Ethernet MCA 10/100 Adapter.
When the adapter description file has been copied onto you REFERENCE/
USER diskette, you are returned to the MAIN MENU.
5. Select the “SET CONFIGURATION” function to invoke the configuration
menu.
6. Select “RUN AUTOMATIC CONFIGURATION”.
The default settings are: I/O address location: 200h, interrupt level: IRQ2, and
RPL: RPL disabled.
Select the “VIEW CONFIGURATION” function from the SET
CONFIGURATION menu if you want to know the exact settings.
➽Note: If you are installing to NetWare 3.12, NetWare 4.x, or Windows 95, select
the “VIEW CONFIGURATION” function from the SET CONFIGURATION
menu. Make a note of the slot number, as you will need it later.
You may now proceed to chapter 7 to install the driver software.
❏

10
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Hardware Installation

11
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Windows 95 Express Installation
4. Windows 95 Express Installation
Windows 95 will normally install new devices with little or no user intervention.
This is however not the case for MCA adapters, as Windows 95 cannot autodetect
these adapters. Follow the steps below to install the Ethernet MCA 10/100
Adapter.
1. Install the Ethernet MCA 10/100 Adapter in a free expansion slot and connect
the cable between the adapter and the network as described in chapter 3.
2. Start Windows 95.
3. Select “Settings” and “Control Panel” from the Windows 95 “Start Menu”.
4. From the “Control Panel”, select “Network”.
5. Press “Add” and select “Add Adapter”.
6. From the Select Network Adapters window, press “Have Disk”, insert the
Olicom Driver disk, and select “Olicom Ethernet MCA 10/100 Adapter (OC-
2335)”.
7. Press “OK” to complete the installation.
8. Restart Windows 95 for the changes to take effect.
❏

12
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Windows 95 Express Installation

13
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 NetWare Client Express Installation for DOS and Windows 3.1x
5. NetWare Client Express Installation
for DOS and Windows 3.1x
NetWare Client Express Install is for DOS and Windows 3.x users who want to
configure their computer as a Novell NetWare Client (DOS ODI workstation)
using Novell’s Virtual Loadable Module.
Express Install installs the necessary drivers and programs to attach your PC to a
Novell NetWare network and also lets you install the utilities provided with the
Ethernet MCA 10/100 Adapter.
The following disks are required:
•The Olicom Setup Disk
•The Olicom NetWare Client Disk
1. Make sure the adapter is inserted and connected as described in chapter 3.
2. Insert the Olicom Setup Disk, select “Run...” and enter:
A:\SETUP
and press
Enter
(or click on “OK”).
Alternatively, enter “A:\INSTALL” from the DOS prompt.
Figure 4. Opening Screen - NetWare Client Express Install
3. Select the “Yes” button in the “Welcome to Olicom Setup” to run the Express
Installation (use the mouse or press
Enter
).