olympia electronics BSR-8020/WP User manual

921802002_09_005
Page 1 from 9
ON
OFF
GENERAL
The red LED which blinks periodically in the quiescent state is a power and good operation indication. The
LED lights and remains lit when the specific input unit issues an alarm to the panel. The LED remains also lit
when the sirens are deactivated from the panel in order to indicate the precise point where the alarm
originated from. The Led is turned OFF after a panel reset. Each device must have an address, that is
recognized by the panel. It is not allowed for two devices on the same loop to have the same address. Page 4
contains the full table that shows the addresses and the setting with the dip-switches. Up to 127 units can
connected to each panel.
4. Notice!! If an additional entry hole is required then remove the break-out plastic and install the supplied
The input-output unit is recognized and programmed by the BSR-2100 panel. This device is used in order that
non-addressable devices that have a free relay contact (such as fire alarm panels, flow switches and
conventional detectors) to be connected on the loop. The input unit is fully monitored and has the capability to
send to the panel, with a suitable connection, three states: quiescent, fault, alarm.
6. Reinstall the front cover and fasten the screws that were removed in step 1.
The output unit contains a fully programmable by the panel relay with a rating of (30V/1A).
INSTALLATION (Notice!!! The mounting accessories are included).
1. Unfasten the front cover screws and remove the cover.
5. Set the address on the dip-switch (page 4 and 5).
3. Pass the cables through the cable glands and make the required connections.
cable gland.
2. Locate the mounting holes and use the supplied accessories to mount the unit on the required position.
21-28V
ABS/PC
ALARM CONSUMPTION WHEN USED AS A CONVENTIONAL DEVICE DRIVER
QUIESCENT CONSUMPTION WHEN USED AS A CONVENTIONAL DEVICE DRIVER
30mA
5.6mA
IP65
1.3mA (with activated LED)
o
-10 to 60 C
Up to 95%
2 years
170gr.
155x80x43mm
EN 54-18
TECHNICAL CHARACTERISTICS
RELATIVE HUMIDITY
CONSTRUCTIONAL MATERIAL
WEIGHT
DIMENSIONS
GUARANTEE
OPERATION VOLTAGE
QUIESCENT CONSUMPTION
ALARM CONSUMPTION
PRODUCED IN ACCORDANCE WITH
OPERATION TEMPERATURE RANGE
DEGREES OF COVER PROTECTION
0.7mA
INSTALLATION
EXTERNAL POWER SUPPLY
For internal use only
21-28V
Olympia Electronics - European manufacturer
Thank you for your trust in our products
Indicator LED
4
BSR-8020/WP Waterproof Addressable input-output unit
2
2
3
3
5
1

Page 2 from 9
9
ON
10
9
ON
10
9
ON
10
9
ON
10
Dip-switches
9 & 10 Operating mode
Input/Output unit
Input unit
Conventional detector driving unit
Conventional detector driving unit with external power supply
4) Conventional detector driving unit with external power supply.
The above functions are set using the dip-switches 9 and 10. The dip-switch 8 determines a
sub function depending on the case.
1) Input/Output Unit
In this function input and output units are independent.
The device has 4 different operation modes:
2) Input unit
OPERATION
The input unit with auxiliary relay is used so as to provide an additional input to the loop. Gas
sensor types BS-685 and BS-686 can also be connected. It contains an input that is fully
monitored for open and short circuit conditions and a relay (1A/30V), which is activated for 5
seconds after a panel reset (when the dip-switch number 8 is in the OFF position). On the
panel, the input units are shown as “INPUT UNIT ΧΧΧ” (where ΧΧΧ is the set address of the
device). In this function, the terminal resistor is 56kΩ and the alarm resistor is 10kΩ.
The input unit is used in order to connect non addressable devices, that have a free relay
contact (such as conventional alarm panels, or flow switches), to the loop of the panel. The
input unit is fully monitored and has the capability to send to the panel, with a suitable
connection, three states: quiescent, fault, alarm. The output unit contains a relay that is fully
programmable from the panel with a rating of (30V/1A). The red LED which blinks periodically
in the quiescent state is a power and good operation indication. On the panel, the input unit is
shown as “INPUT/OUTPUT UNIT ΧΧΧ” (where ΧΧΧ is the set address of the device). In this
function, the terminal resistor is 56kΩ and the alarm resistor is 10kΩ.
3) Conventional detector driving unit
The driving unit for conventional detectors is used in order to connect conventional detectors
to the addressable panel. The device can be connected to the BSR-2104 and BSR-2114
panels. It can power up to 10 detectors and has protection against the detection of an open
circuit or the disconnection of a detector. A 56kΩ resistor is installed by default on the
terminals +IN, -IN. We replace the 56kΩ resistor with a 10kΩ resistor. We install the 10kΩ
resistor to the last detector of the line. On the panel, the input unit is shown as ``ADAPTOR
UNIT ΧΧΧ`` (where ΧΧΧ is the set address of the device). The LED lights and remains lit
when the specific input unit issues an alarm to the panel. The LED also remains lit if the sirens
are deactivated from the panel. The LED of the detector that issued the alarm also remains lit
in order to show the precise alarm origin. LED is turned OFF after a panel reset. In this
operation we have increased consumption and cannot connect more than 7 BSR-8020/WP
on each loop. In this function the terminal resistor is 10kΩ and the alarm resistor is 1kΩ .
This function is the same as the previous one. The only difference between the two, is that an
external power supply is used. The external power source must have an output rating of 21-
28V and must not be interrupted during a power failure.In this function the terminal resistor is
4.7kΩ and the alarm resistor is 1kΩ .
921802002_09_005

Page 3 from 9
+L -L +L -L
AP
1 2 3 4 5 6 7 8
ON
Loop Loop Loop
Loop
IN
IN
OUT
OU T
R
IN
IN
OUT
OU T
R
IN
IN
OUT
OU T
R
IN
IN
OUT
OU T
R
+24V
IN
NO
+IN
C
-IN
NC
ON
OFF
+L+L+L
-L
PE PE
+L+L+L
-L
+24V
IN
NO
+IN
C
-IN
NC
ON
OFF
+L+L+L
-L
PE PE
+L+L+L
-L
Input connection terminals.
The input is fully monitored and has by default
a (56kΩ) resistor. On the 24V IN
terminal you can connect an external power supply
if the function conventional detector driving unit with
external power supply is selected.
Indication LED
Blinks periodically in quiescent state
Is ON when a specific device issues an alarm
Goes OFF after a panel reset
Relay connection terminals
(NO, C, NC)
Address select dip-switch (1-7)
Subfunction select dip-switch (8)
Function select dip-switch (9-10)
Loop connection terminal
Connection terminal with ground
+24V
IN
NO
+IN
C
-IN
NC
ON
OFF
+L+L+L
-L
PE PE
+L+L+L
-L
921802002_09_005

Page 4 from 9
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
1 1 1
1
1
1
1
1
1
1
1 1 1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
11
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
11
ON ON ON
ON
ON
ON
ON
ON
ON
ON
ON ON ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ONON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ONON
2 2 2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
22
2 2 2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
22
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3 3 3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3 3 3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4 4 4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4 4 4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5 5 5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5 5 5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6 6 6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6 6 6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7 7 7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7 7 7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8 8 8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8 8 8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
3
4
Address Dip-switch
setting Address Dip-switch setting Address Dip-switch setting Address Dip-switch setting
921802002_09_005

Page 5 from 9
125
126
127
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
22
22
22
2
33
3
3
3
3
3
44
4
4
4
4
4
55
5
5
5
5
5
66
6
6
6
6
6
77
7
7
7
7
7
88
8
8
8
8
8
121
122
123
124
Address Dip-switch
setting Address Dip-switch setting
Connecting a BSR-8020/WP to a BS-1636 panel. ALARM and FAULT RELAYS are
used. According to this connection, when the panel detects a fault, the BSR-8020/WP
will send a fault signal to the central panel and when the BS-1636 detects alarm on a
zone, the BSR-8020/WP will send an alarm signal.
BS-1636 terminals
Loop
Connecting a BSR-8020/WP with an isolation lock. When the lock is activated (short
circuit), the output of the device does not operate and the message “ DISABLEMENT ”
is shown on the panel. The dip-switch 8 of the BSR-8020/WP must be in the ON
position. It can be used in a fire extinguishing system.
10kΩ
Operation as an Input/Output unit
Operation as an Input/Output unit
56kΩ
Loop
Operation Dip-switch setting
1
1
ON
ON
2
2
3
3
4
4
5
5
6
6
7
7
8 9 10
8 9 10
Operate with independent
programmable
input and output
Operate with a controller
output by the input
(Extinguishing function)
Connecting with a flow switch
+24V
IN
NO
+IN
C
-IN
NC
ON
OFF
+L+L+L
-L
PE PE
+L+L+L
-L
+24V
IN
NO
+IN
C
-IN
NC
ON
OFF
+L+L+L
-L
PE
PE
+L+L+L
-L
Connection with a conventional panel
56kΩ
NC
NC
C
C
N0
N0
10kΩ
ALARMFAULT
921802002_09_005

Page 6 from 9
Connecting a BSR-8020/WP with detectors ΒS-685 or ΒS-686. The auxiliary relay is
used so as to interrupt the power to the detectors after a panel reset.
24V power supply
from panel
56kΩ
10kΩ
Loop
Loop
Operate as a Input unit
Operation Dip-switch setting
Relay is activated for
5 seconds after a reset 1
ON
2 3 4 5 6 7 8 9 10
1
ON
2 3 4 5 6 7 8 9 10
The relay is activated
only when the input
is activated
BS-685
or
BS-686
BS-685
or
BS-686
+24V
IN
NO
+IN
C
-IN
NC
ON
OFF
+L+L+L
-L
PE PE
+L+L+L
-L
Connecting gas detectors
921802002_09_005

Page 7 from 9
Loop
Loop
10kΩ
BS-572
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
Operation Dip-switch setting
Convetional detector driving unit
During an alarm, it
interrupts
the power to the zone to
reduce the consumption
During an alarm, the
power of the zone remains
in order to indicate which
detector issued the alarm.
1
ON
2 3 4 5 6 7 8 9 10
1
ON
2 3 4 5 6 7 8 9 10
+
R
+24V
IN
NO
+IN
C
-IN
NC
ON
OFF
+L+L+L
-L
PE
PE
+L+L+L
-L
Connecting a BSR-8020/WP with conventional detectors. A 10kΩ terminal resistor must
be connected on the last detector. The maximum number of detectors per unit is 10. An
external LED BS-572 can be connected on one of the detectors. With the dip-switch 8 we
can set if during an alarm the zones power will be interrupted or not. (according to the
table above). If the dip-switch 8 is in the ON position, the maximum number of devices is
7, whereas if the dip-switch 8 is in the OFF position, the maximum number of devices is
30. The total consumption must also include the consumption of the other devices.
921802002_09_005

Page 8 from 9
Loop
Loop
4.7kΩ
+
R
BS-572
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
Conventional detector driving unit with external power supply
External
power
24V
Operation Dip-switch setting
1
ON
2 3 4 5 6 7 8 9 10
1
ON
2 3 4 5 6 7 8 9 10
During an alarm, it
interrupts
the power to the zone to
reduce the consumption
During an alarm, the
power of the zone remains
in order to indicate which
detector issued the alarm.
+24V
IN
NO
+IN
C
-IN
NC
ON
OFF
+L+L+L
-L
PE
PE
+L+L+L
-L
Connecting a BSR-8020/WP to conventional detectors. A 4.7kΩ resistor must be installed
on the last detector. The maximum number of detectors per device is 40 conventional
detectors of olympia electronics. According to EN 54 the maximum number of
detectors per zone is 32 devices. The maximum consumption of the detectors in
idle state, must not exceed the 2.5mA.
Additionally, the external power supply must be isolated from the main power grid and its
power must be calculated depending on the maximum load. If for example we have 10
such devices and each device consumes 30mA during an alarm then the power supply
must be capable of providing at least 300mA.
The power is supplied by an external power supply and thus does burden the loop. The
power consumption is that of an input/output unit. The external power supply must have
an output range 21-28V and must not be interrupted during a power failure.
921802002_09_005

Page 9 from 9
Olympia Electronics guarantees the quality, condition and operation of the goods. The period
of warranty is specified in the official catalogue of Olympia Electronics and also in the
technical leaflet, which accompanies each product. This warranty ceases to exist if the buyer
does not follow the technical instructions included in official documents given by Olympia
Electronics or if the buyer modifies the goods provided or has any repairs or re-setting done
by a third party, unless Olympia Electronics has fully agreed to them in writing. Products that
have been damaged can be returned to the premises of our company for repair or
replacement, as long as the warranty period is valid.
72nd km. O.N.R. Thessaloniki-Katerini
WARRANTY
HEAD OFFICE
www.olympia-electronics.com
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not
charge the buyer depending on the reason of defection. Olympia Electronics reserves the
right to charge or not the buyer the transportation cost.
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
[email protected]
1922
Waterproof Addressable input-
output unit BSR-8020/WP certified
from DEDAL. Also DEDAL. controls
the production according to the
CPR number:
Certification
921802002_09_005
BSR-8020/WP Waterproof
Addressable input-output unit
1922-CPR-1788 22
EN-54-18: 2005
EGINIO PIERIAS
60300 GREECE