Olympia L-7470 Series User manual

INSTALLATION
Tools:
Adjustable Wrench Plumbers Putty Sealant Tape Rags
Model Number: L-7470, L-7472 (CP, PVD BN,
ORB)
Warnings and Notes:
Check with local plumbing code requirements before installation.
This product should be installed by a local listed plumber.
Do not use plumbers putty on threads.
OLYMPIA FAUCETS, INC.
Interchange City Distribution Center #20
1277 Heil Quaker Boulevard
La Vergne, TN 37086
[phone]
www.olympiafaucets.com
Installation Steps:
Two Handle Lavatory Widespread Faucet
(1) Shut off water supplies. Remove old faucet.
Clean mounting surface in preparation for new
faucet.
(2) Ensure there is a washer under the spout
ange. Place the spout in position on the sink.
From under the sink slide mounting bracket
through spout shank. Thread nut onto spout
shank properly and tighten nut
(3) Thread “Y” connector to the spout shank.
Ensure there is a washer in the “Y” connector.
Do not overtighten.
(4) Thread valve ange to valve. Install Cold
and hot handle to the valve with the help of
3/32” Allen wrench. Place hot and cold side
valve in position on the sink. Ensure handles
turns in correct direction.
(5) From under the sink place washers and
thread locknut with the help of 1-11/32” size
socket. Connect outlet hose to Y connector.
Connect inlet tube to water supply.
(1) Remove pop-up ange from body
(2) Place a ring of putty on the bottom of
ange.
(3) Insert pop-up ange through drain hole
and attach ange to body. Ensure the pop-
up outlet faces towards the sink. Do not
overtighten.
Pop-up Drain Installation:
(6) Turn on water supplies. Check for any
minor joint leaks. Remove aerator from spout
by turning counterclockwise. Turn on both side
handles. Flush and allow water to run at full
ow at least one minute. Turn off both side
handles. Replace aerator

Exploded Drawing:
* Note: Please specify nish/color when ordering. ITEM # DESCRIPTION
A OP-490011 3/32” Allen Wrench
B OP-190015C,H* Lever Handle-Cold, Hot
C OP-430027* Escutcheon & Gasket
D OP-490006 Bonnet Nut
E OP-330002C,H Ceramic Disc Cartridge-Cold,Hot
F OP-590002 Valve Mounting Kit
G OP-590001 Supply Nut
H OP-490008 Flex Connector Hose
I OP-490009 “Y” Connector & Washer
J OP-430001 Spout Mounting Kit
K OP-230005* ‘J’ Style Spout
L OP-630004* 50/50 Pop-Up Drain Assembly
(For L-7470)
M OP-630002* Brass Pop-Up Drain Assembly
(For L-7472)
1 OP-490029 3/32” Allen Screw
2 OP-490010* 1.5 GPM Aerator
3 OP-430028 Washer
For more care information or trouble shooting
inquiries about your Olympia product, Please call:
OLYMPIA FAUCETS, INC. [phone]
8AM - 8PM EST (5AM to 5PM PST)
www.olympiafaucets.com
(6) Push pivot rod down, insert drain plug
carefully. Test to ensure drain plug works
properly.
(7) Connect lift rod strap to pivot rod by using
clip. Tighten the thumbscrew to connect lift rod
strap to pop-up lift rod.
(5) Remove pivot rod nut from pop-up body,
ensure the washers is in place, insert pivot
rod, tighten pivot rod nut back to pop-up body.
(4) Remove the excess putty. Connect the
trap (check manufacturer’s instructions for
installation).