Olympus Stylus TG-Tracker User manual

Thank you for purchasing an Olympus digital camera. Before you start to
use your new camera, please read these instructions carefully to enjoy
optimum performance and a longer service life. Keep this manual in a safe
place for future reference.
We recommend that you take test shots to get accustomed to your camera
before taking important photographs.
The screen and camera illustrations shown in this manual were produced
during the development stages and may differ from the actual product.
Instruction Manual
DIGITAL CAMERA
STYLUS
TG-TRACKER

2 EN
Unpack the box contents
The following items are included with the camera.
If anything is missing or damaged, contact the dealer from whom you
purchased the camera.
Digital camera
or
Strap Lithium Ion Battery
(LI-92B) USB-AC adapter (F-5AC)
CD-ROM
(Instruction
manual/
Computer
software)
Lens
protector
(LP-T01)
Underwater lens
protector
(UP-T01) USB cable
(CB-USB10)
Joint screw
(JS-T01) Mount coupling (MC-T01) Steady grip (SG-T01)
Other accessories not shown: Warranty card
Contents may vary depending on purchase location.
• When using the camera underwater, be sure to attach the underwater lens
protector (P. 60) and select [ ] (underwater wide-angle) or [ ]
(underwater flipped wide-angle) for [Field of View] (P. 27, 31, 32).
Attaching the camera strap
1
2
3
• Pull the strap tight so that it does not come loose.

3 EN
Names of parts
1
2
3
4
10 11
12 23
24
13
11 21
1716 18 19 20
22
14 15
5
6
7 98
1Headlamp
2Lens
3Lens protector
4 Strap eyelet
5Battery/card
compartment/
connector cover
6Battery/card
compartment/
connector cover latch
7HDMI micro
connector
8Micro-USB connector
9Card slot
0Power switch (ON/
OFF/LOG)
aStereo microphone
bLens latch
cWi-Fi antenna
dSpeaker
eTripod socket
fIndicator lamp
gR(record) button
hbutton
iOK/MODE button
jGPS antenna
kM(Left)/Wi-Fi
button
lN(Right)/INFO/
Y(headlamp) button
mMonitor
nPressure adjustment
hole*
*Do not stick pointed objects like a pin into the hole.
• You can adjust the angle of the monitor.
• Strong vibrations may cause the monitor to
open.

4 EN
Preparations for shooting
Inserting and removing the battery and card
1
Keeping the battery/card compartment/connector cover latch
pressed (1), open the battery/card compartment/connector
cover (2, 3).
• When opening or
closing the battery/card
compartment/connector
cover, be sure the power
switch is in the OFF
position.
Battery/card compartment/
connector cover
Battery/card compartment/
connector cover latch
1
3
2
2
Insert the battery while sliding the battery lock knob in the
direction of the arrow.
• Insert the battery
as illustrated
with the m
mark toward
the battery lock
knob.
Battery lock knob
• If you insert the battery in the wrong direction, the camera is not turned
on. Be sure to insert it in the correct direction.
• Slide the battery lock knob in the direction of the arrow to unlock, and
then remove the battery.

5 EN
3
Insert the card straight until it clicks into place.
• Do not touch the metallic parts
of the card directly.
• Always use the specified cards
with this camera. Do not insert
other types of memory cards.
Cards compatible with this camera
microSD/microSDHC/microSDXC card (commercially available) (for
compatibility card details, visit the Olympus website.)
• g“Using the card” (P. 58)
To remove the card
• Before removing cards, rotate the power switch to OFF and confirm that
the indicator lamp (amber) is off.
• Press the card in
until it clicks and
comes out slightly,
then remove the
card.
12
4
Follow Steps 1, 2and 3to close the battery/card compartment/
connector cover.
• When using the camera, be sure to close the battery/card compartment/
connector cover.
• Securely latch the cover by sliding the battery/card compartment/
connector cover latch until it completely covers the red label.
12
3
• Read “Important information about water and shock resistant features” (P. 62)
before using the camera under water.

6 EN
Charging the battery
1
Check that the battery is in the camera, and connect the USB
cable and USB-AC adapter.
• The battery is not fully charged at shipment. Before use, be sure to
charge the battery until the indicator lamp turns off (up to 3.5 hours).
AC outlet
Battery/card
compartment/
connector cover
USB cable (supplied)
Micro-USB connector Indicator lamp
(amber)
On: Charging
Off: Charged
For charging the battery abroad, see “Using your charger and USB-AC adapter
abroad” (P. 57).
• Never use any cable other than supplied or Olympus-designated USB cable.
This may cause smoking or burning.
• The included F-5AC USB-AC adapter (hereafter referred to as USB-AC
adapter) differs depending on the region where you purchased the camera.
If you received a plug-in type USB-AC adapter, plug it directly into AC outlet.
• Be sure the power switch is in the OFF position during charging.

7 EN
• For details on the battery, see “SAFETY PRECAUTIONS” (P. 65). For details
on the USB-AC adapter, see “SAFETY PRECAUTIONS” (P. 65).
• If the indicator lamp does not light, reconnect the USB cable and USB-AC
adapter to the camera.
When to charge the batteries
Charge the battery when the
error message shown on the right
appears.
Error messageFlashes in red
17 : 30 Battery Empty

8 EN
Turning on the camera
The camera can only be used with a card inserted. Insert a card
in the camera.
• g“Using the card” (P. 58)
Rotate the power switch to ON.
• If the camera does not turn on when the power
switch is in the ON position, check that the
battery is in the correct orientation.
g“Inserting and removing the battery and
card” (P. 4)
Setting the clock
The camera will prompt you to set the clock when first turned on. Pictures
can not be taken until the clock is set. For information on changing the time
zone or resetting the clock, see [Date] (P. 37).
1
Use Mor Nto choose the year
([Y]) and press OK to select.
Date
:Back
MENU
:Set
OK
2016 --
.. :-- -- --
YMDTime
2
Using Mor Nand pressing OK as described in Step 1, set
the month ([M]), day ([D]), and hours and minutes ([Time]).
3
Use Mor Nto select a time zone
and press OK.
World Time
:Back
MENU
:Set
OK
UTC+09:00 (10:38)
Seoul
Tokyo

9 EN
Viewing the shooting mode
The monitor turns on when the power switch is rotated to ON. The shooting
mode is shown by an icon in the top left corner of the display.
A: VIDEO (movie) mode ...................(P. 10)
l: Displayed when [On] is selected for
[Loop] in the VIDEO menu (P. 27).
j: Displayed when [Continuous] is
selected for [Drive] in the PHOTO
menu (P. 30).
z: PHOTO (photography) mode .......(P. 12)
L: TIME LAPSE
(time-lapse movie) mode .............(P. 14)
Shooting setting icons
Settings selected in the menus and elsewhere are shown by icons at the
top of the shooting display.
w: [WB] ...............................(P. 27, 30, 32)
F: [Field of View] .................(P. 27, 31, 32)
o: [IS] ...............................................(P. 29)
Y: [Timer] ..........................................(P. 31)
w: [Wi-Fi] .........................................(P. 36)
F: [+/-] ...................................(P. 27, 30, 32)

10 EN
Recording movies
1
Rotate the power switch to ON.
• While the power switch is in the ON position, the camera will log GPS
and other sensor data, including position and altitude. Log recording
continues during shooting.
2
Check the mode. VIDEO (movie) mode
3
Press the R(record) button to
start recording.
• Sound will be recorded with movie
footage shot with [30 fps] or [60
fps] selected for [fps] in the VIDEO
menu (P. 28). Be careful not to cover
the microphone.
• When using a camera with a CMOS
image sensor, moving objects may
appear distorted due to the rolling
shutter phenomenon. This is a
physical phenomenon whereby
distortion occurs in the filmed image
when shooting a fast-moving subject
or due to camera shaking.
• Chapter marking can be added by
pressing OK during movie recording.
Movies can have up to 200 chapters.
17 : 30
REC
Recording time
4
Press the Rbutton again to stop recording.

11 EN
• If the power switch is rotated to OFF while the
current log is stored in the temporary buffer,
a message will be displayed in the monitor. If
10 seconds pass or you press OK while the
message is displayed, log recording will end
and the log will be saved to the card. If you
rotate the power switch to LOG or ON before
the 10 seconds are up, log recording will
continue and the log will not be saved to the
card.
Continue LOG
Exit 10
• To disable log recording when the power switch is in the ON position, select
[Off] for [LOG Setting] in the SETUP menu (P. 34).
• Do not set the clock during log recording (P. 37). The log will not display
correctly in OI.Track.

12 EN
Taking photographs
1
Rotate the power switch to ON.
• While the power switch is in the ON position, the camera will log GPS
and other sensor data, including position and altitude. Log recording
continues during shooting, and the log is saved to the card when the
power switch is rotated to OFF.
2
Press the MODE button to view the
home display.
• Use Mor Nto highlight items.
VIDEO
Home display
3
Highlight [zPHOTO] and press OK.PHOTO
4
Press the R(record) button to
take photos.
• If [On] is selected for [LOG
Setting]intheSETUPmenu(P.34),
photos will include tags giving
the position, altitude, and other
location data. 790

13 EN
• Distortion may appear in photos of moving objects.
• Large movements or flicker from fluorescent lights or other sources may
cause the picture to break up.
• To disable log recording when the power switch is in the ON position, select
[Off] for [LOG Setting] in the SETUP menu (P. 34).
• Do not set the clock during log recording (P. 37). The log will not display
correctly in OI.Track.

14 EN
Filming time-lapse movies
The camera shoots photos at a pre-selected interval and joins them
together in a movie. Sound is not recorded.
1
Rotate the power switch to ON.
• While the power switch is in the ON position, the camera will log GPS
and other sensor data, including position and altitude. Log recording
continues during shooting, and the log is saved to the card when the
power switch is rotated to OFF.
2
Press the MODE button to view the
home display.
• Use Mor Nto highlight items.
VIDEO
Home display
3
Highlight [LTIME LAPSE] and press
OK.TIME LAPSE
4
Press the R(record) button to
start recording.
• Photos are taken one at a time
at the interval selected using the
[Interval] option (P. 33).
17 : 30
5
Press the Rbutton again to stop recording.
• The photos are joined together in a movie.

15 EN
• If the battery runs low during recording, shooting will end and the camera will
begin to record the movie to the card. Use a fully-charged battery. A movie will
be created from the photos shot before shooting was suspended.
• Time-lapse movies can be up to 29 minutes long (or 4 GB in size).
• To disable log recording when the power switch is in the ON position, select
[Off] for [LOG Setting] in the SETUP menu (P. 34).
• Do not set the clock during log recording (P. 37). The log will not display
correctly in OI.Track.

16 EN
Viewing and deleting pictures
Viewing movies
1
Rotate the power switch to ON.
2
Press the MODE button to view the
home display.
• Use Mor Nto highlight items.
VIDEO
Home display
3
Highlight [qPLAY] and press OK.
• Pictures will be displayed in a thumbnail list.
• Use Mand Nto highlight pictures.
• Photos are indicated by a zicon.
102 - 3459
4
Highlight the desired movie and press
OK to view it full frame.
• Press Mto return to thumbnail playback.
102 - 3459
5
Press OK again to begin playback.
• Press OK to pause playback. To resume,
press OK again.
• Press the R(record) button to exit to the
shooting display.

17 EN
During playback
Pausing playback Press the OK button to pause playback.
Fast forward Press Nonce for 2× speed, twice for 15× speed.
Rewind Press Monce for 2× speed, twice for 15× speed.
Operations while playback is paused
During pause
Elapsed time/
Total shooting time 00
: 12 : 34 / 00 : 17 : 30
Cueing Use Mto return to the previous chapter or Nto
skip to the next chapter. If there is no next chapter,
the final frame will be displayed.
Fast forward Press and hold Nto fast forward.
Rewind Press and hold Mto rewind.
Resuming playback Press the OK button to resume playback.
To stop movie playback
Press the button.
• To play back movies on the computer, the supplied PC software is
recommended. For the first use of the PC software, connect the camera to the
computer, then launch the software.

18 EN
Viewing photographs
1
Rotate the power switch to ON.
2
Press the MODE button to view the
home display.
• Use Mor Nto highlight items.
VIDEO
Home display
3
Highlight [qPLAY] and press OK.
• Pictures will be displayed in a thumbnail list.
• Use Mand Nto highlight pictures.
• Photos are indicated by a zicon.
102 - 3455
4
Highlight the desired photo and press
OK to view it full frame.
• Press Mto return to thumbnail playback.
• Press the R(record) button to exit to the
shooting display.
102 - 3455

19 EN
Deleting pictures
1
In the thumbnail list, highlight the
picture you want to delete and press
the button.
• The playback menu will be displayed.
102 - 3459
• You can also press the button to
display the playback menu in full-frame
playback.
102 - 3459
2
Use Mor Nto highlight [SErase]
and press OK.Erase
:Back
MENU
:Select
OK
Exit
Exit
3
Highlight [YES] and press OK.
• To exit to the playback menu without deleting
the picture, highlight [NO] and press OK.
• All pictures can be erased at a time (P. 37).
Erase
:Back
MENU
Caution Erases Image
NoYes

20 EN
Recording and using logs (LOG mode)
While the power switch is in the LOG position, the camera will log
GPS and other sensor data (P. 22). Logs can be downloaded for use
with the OLYMPUS Image Track (OI.Track) smartphone app.
Recording and saving logs
Rotate the power switch to LOG.
• Log recording will start. The indicator lamp lights
green during recording.
• To switch to the shooting display, rotate the power
switch to ON.
• Log recording does not function if no card
inserted.
• The camera automatically terminates log data acquisition and recording when
the battery runs low. Rotate the power switch to OFF to save the log.
• In LOG mode, the camera draws on the battery continuously to acquire
location data.
• An altitude (water depth) track can be viewed in the altitude (water depth) log
display (P. 23). The camera can not display other track logs.
• No additional log data can be recorded after temporary memory buffer used to
store log data fills. If the buffer fills, rotate the power switch to OFF to save the
log data to the card.
Saving logs
The current log is saved to the card when the power switch is rotated to
OFF.
• A message is displayed in the monitor when the
power switch is rotated to or through the OFF
position. If 10 seconds pass or you press OK
while the message is displayed, log recording will
end and the log will be saved to the card. If you
rotate the power switch to LOG or ON before the
10 seconds are up, log recording will continue
and the log will not be saved to the card.
Continue LOG
Exit 10
• [Busy…] is displayed in the monitor while the log is saved. Do not remove the
card while this message is displayed. Removing the card before the operation
is complete could result in loss of the log file or in damage to the camera or
the card.