Omega ORU50PX Installation guide

CONTENTS
Instructions for the Use and Care and Installation of
ORU50PX
Undermount Range Hoods

CONTENTS
1) WARNING
2) INSTALLATION INSTRUCTIONS
3) OPERATION
4) LIGHT REPLACEMENT
5) CLEANING
6) ATTENTION
7) TROUBLESHOOTING
8) APPLIANCE DIMENSIONS
It is important that you retain these instructions, proof of purchase as well asother
important documents about this product for future reference.
Due to continual product development, Omega reserves the right to alter
specifications or appearances without notice.
Dispose of packaging responsibly –recycle where facilities areavailable.

1. WARNING
 Young children should be supervised to ensure that they do not play with the
appliance.
 The appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experienceand
knowledge, unless they have been given supervised or instruction concerning
use of the appliance by a responsible person for their safely.
 If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
 Yourcooker hood is for domestic use only, not suitable for barbecue, fast -food
shops, and other commercial use.
 Any installation work must be carried out by a qualified electrician or competent
person.
 The cooker hood and its filter mesh should be cleaned regularly in order to keep
in good working order.
 Before cleaning, always ensure that you have switched your cooker hood off.
 Do not flambé under the range hood.
 Clean the cooker hood according to the instruction manual, and keep the
cooker hood away from the danger of flames.
 If there is any fault with your cooker hood, please call the customerservice
number in the Warranty Card.
 Please keep the room adequately ventilated when your cooker hood and gas
hob are working.
 Caution: Accessible parts may become hot when used with a cooking
appliance
Note: The instructions must include details concerning cleaning instructions and
frequency of cleaning.
For Installation Instructions:
The exhaust air must not be discharged into a flue which is used for exhausting
fumes for other appliances burning gas or other fuels. (Not applicable for
appliances which only discharge air back into the room.
The minimum distance between the supporting surface for the cooking vessels
of the hob at the lowest part of the range hood must be 65cm.
Regulations concerning the discharge of air have to be fulfilled.
Warning: Failure to install the screws or fixing devices in accordance with the
instructions may result in an electrical hazard.

2. INSTALLATION
Please ensure that before installing the range hood all power has been switched off.
Installation must be in accordance to the local electrical authority and codes. This
range hood must be earthed at all times for the operators’ safety.
The power socket for the range hood should be positioned to enable the user to turn
the power on and off easily (as there are no controls on the appliance) and to turn the
appliance off to enable cleaning and any maintenance required.
Ensure that when installing the range hood, that it is protected from any possible
damage from tools etc.
Ducting for this unit must be installed in accordance to the local authority. Ensure that
the fixings used for this range hood are suitable.
Check the area where the range hood is to be fitted, to ensure that it is
structurally sound.
Before using the appliance, remove the plastic coatings protecting the stainless
steel finish.
Ensure that the wall is structurally sound, and is capable of carryingthe
weight
of the range hood.
It is recommended that the dimension be checked on the rangehood before
installing.
1.
The cooker hood should be placed at a distance of 65-75cm from the
cooking surface for the best effect.
2. Drill a hole in the cupboard, 490*265(mm) for model ORU50PX. Make sure
the distance between the edge of the hole and the edge of the cupboard
edge is at least 35mm. Remove the filter. Remove the two halogen lights
(twist anticlockwise), unscrew the two screws holding the lower facia panel
and remove the lower fascia panel.
3. Fit the two flaps into the outlet (tabs facing upwards) creating the one way
valve.
4. Fit the appliance into the 490*265mm hole, and fix into place using the
supplied wood screws (8 positions).
5. Reattach the lower fascia panel using the two original 10mm screws. Refit
the two halogen lights and attach the filter.
6. Connect the electrical plug to the power socket and test that the lights and
fan operate when power is turned on.
7. Connect ducting (outlet is Ø150mm) to the outlet of the appliance. The
ducting must remove the exhaust from the room.

3. OPERATION:
Note: Before the unit can be operated, it must be ducted.
1. Connect the plug to the power at the power socket.
2. Turn power on at the power socket which will start the appliance.
3. To turn the appliance off, turn the power off at the power socket.
If your range hood does not function correctly when attempting any of the above,
please ensure that your power is on and is functioning correctly. If the power
seems to be functioning correctly in the house, there may be a problem with the range
hood. Please call your authorised Omega service centre in this case to organise a
service call.
4. LIGHT REPLACEMENT
1. Turn the power off and disconnect from mains power.
2. Remove filter and read labels regarding maximum lamp ratings.
3. Press the light face and remove by turning in anticlockwise direction.
4. Pull out the halogen light bulb carefully and replace by same type and samerated
halogen light bulb (12V 40W MAX). NOTE: take care as halogen lamps can get hot.
5. CLEANING
SAFETY PRECAUTION
Before cleaning your range hood or performing any maintenance, please ensure
that the range hood been disconnected at the power socket.
Do not use abrasive cleaners to clean the range hood. The use of warmsoapy
water and a cloth are recommended.
Ensure that the range hood is cleaned regularly, as a build-up of grease and fat may
occur otherwise.
The filters on the range hood must be cleaned regularly to maintain efficiency, and
prevent grease build up.
It is recommended that this is undertaken every 4 –6 weeks, depending on
frequency of use.
The filters can be cleaned with warm soapy water or a cloth, or they may be
washed in a dishwasher. If washed in a dishwasher, discolouration may occur to
the mesh and frame.
Cleaning of the range hood must be performed as described above, otherwise
there is a possibility of a fire hazard due to grease and fat build up.

6. SPECIFICATIONS
Voltage
220V-240V~50Hz
Rated motor input power
190W
Illumination
≤40W+40W(GU-10 base halogen)
Rated input power
270W
Airflow
667m3/hr
Outlet diameter
150mm
7. TROUBLESHOOTING
Fault
Cause
Solution
Light does not work,
but motor works.
The lamp may be damaged.
Replace lamp.
Light works, but
motor does not work.
Motor bearings damaged.
Contact Service.
Motor burn out.
Contact Service.
Light does not work,
motor does not work.
Power supply interrupted.
Check at meter board.
Plug incorrectly fitted.
Push plug in.
Power wire cut.
Contact service.
Appliance vibrates
excessively.
Fan is damaged.
Contact service.
Motor screw loose.
Contact service.
Mounting screw loose.
Tighten screw.
Insufficient suction.
The distance between the body and
the cooktop is too high.
Readjust the distance.
Cross-ventilation too strong or not
enough ventilation.
Reduce cross-ventilation or
open the window.
Ducting too long.
Reduce ducting length.
Outlet valve not opening.
Check flaps are opening.
The outside wind is too strong.
No the technical problem.

8. APPLIANCE DIMENSIONS