One Forall SV-1716 User manual

Instruction Manua l
V 1716
English
SV_1716_AV_Sender UK 15x17:SV_1715_AV_Sender 17 talen 05-11-2007 12:09 Pagina 1

2WWW. ONEFORALL.COM
1
2
3
SV_1716_AV_Sender UK 15x17:SV_1715_AV_Sender 17 talen 05-11-2007 12:09 Pagina 2

WWW.ONEFORALL.COM 3
- This pro uct shoul only be use with the AC power a apters
inclu e or a type that complies with safety stan ar EN60065 an that has the following specification:
9 Volt DC / 300mA.
- This pro uct shoul not be expose to high temperatures.
- This pro uct shoul not be use in amp places or close to water.
- The AC power a apters shoul only be connecte to a power supply of 220-240 VAC / 50Hz.
- This pro uct shoul not be covere .
- Ina equately protecte or sensitive electronic equipment may be affecte by the use of this pro uct.
This interference can lea to amage to either equipment. Before you start, please check whether or not this
pro uct can affect surroun ing equipment.
afety Precautions
The Pro uct ....................................................................................................4
Installation ............................................................................................5
Getting started .....................................................................................6
Trouble Shooting ...............................................................................................7
Table of Contents
English
SV_1716_AV_Sender UK 15x17:SV_1715_AV_Sender 17 talen 05-11-2007 12:09 Pagina 3

4WWW.ONEFORALL.COM
The Au io Vi eo Sen er (SV-1716) is a solution for istributing au io an vi eo signals to every place in the house
without the nee of wires. The AV Sen er gives you the possibility to view any vi eo source (satellite receiver, vi eo
recor er, camcor er, DVD player, igital or analogue Set-Top Box or Pay-TV eco er box) on your secon TV in your
home.
The One For All AV Sen er (SV-1716) package contains:
- TRANSMITTER unit
- RECEIVER unit
- Remote Control Exten er Eye
- Infra-re (IR) Eye
- Two Power a apters
The TRANSMITTER sen s the au io an vi eo signals from the source evice (VCR, DVD, SATELLITE/ CABLE BOX, CAM-
CORDER, etc) by 2.4 GHz to the RECEIVER that is connecte to the estination evice. The Remote Control Exten er
sen s the IR signal in the opposite irection (from RECEIVER unit to TRANSMITTER unit) at a frequency of 433.92 MHz.
TRAN MITTER unit
The TRANSMITTER operates on 9 Volts DC 300mA that is supplie by the AC/DC A apter (inclu e in package).
The Au io an /or vi eo signals are transforme to a 2.4GHz frequency that will be sent via the built-in antenna.
Furthermore the TRANSMITTER transforms the Remote Control Exten er signal (at 433.92 MHz) back to an IR
comman .
RECEIVER unit
The RECEIVER operates on 9 Volts DC 300mA that is supplie by the AC/DC A apter (inclu e in package). The high
frequency signal (2.4GHz) receive by this unit are capture by the built-in antenna of the RECEIVER unit an will be
transforme into the original au io an vi eo signals.
Secon ly a Remote Control Exten er can be controlle too. When an infra re signal is Receive by the Remote
Control Exten er, it will transform the IR comman to 433.92 MHz an can be sent through walls an ceilings.
Please no e ha his fea ure is only accessable for devices ha are con rolled via IR (infra-red) signals a a frequency of
30 - 60 kHz This fea ure does no suppor he 2-way IRDA waveform. If you are unsure of he de ails of he remo e
con rol (IR) ou pu , please refer o he manual of he original device or con ac your cable supplier.
The Product
SV_1716_AV_Sender UK 15x17:SV_1715_AV_Sender 17 talen 05-11-2007 12:09 Pagina 4

WWW.ONEFORALL.COM 5
Put both "RECEIVER" an "TRANSMITTER" on the same channel by using the sli e switch on the back si e of
the units
Connecting the TRAN MITTER unit
Make sure that the SCART is connecte to the correct Output of the evice, normally calle “Line Out”.
If you wish to remotely control the source evice (satellite receiver, vi eo recor er, camcor er, DVD player,
igital or analogue Set-Top Box or Pay-TV eco er box) from another room, for example to change channels
on your satellite receiver, you will nee to:
Connect the IR eye to the TRANSMITTER. Place the IR eye irectly on the IR receiver win ow on the front-si e
of the source evice OR place the IR eye in front of the source evice (make sure there is no interference
of the IR Eye signal going to the IR receiver of the source evice).
Insert the a apter plug into the connector on the backsi e.
Now that the unit is connecte you can switch ON the Unit using the ON/OFF key.
The re LED on the front shoul light up.
Connecting the RECEIVER unit
Make sure that the SCART is connecte to the correct Input of the evice, normally calle “Line In”.
Insert the a apter plug into the connector on the backsi e.
If you want to control the source evice, place the Remote Control Exten er on top or besi e the estination evice
where it is able to catch the IR comman from your remote control.
Now that the unit is connecte you can switch ON the Unit using the ON/OFF key.
The re LED on the front shoul light up.
Installation
ee page 2
1
2
3
SV_1716_AV_Sender UK 15x17:SV_1715_AV_Sender 17 talen 05-11-2007 12:09 Pagina 5

6WWW.ONEFORALL.COM
The following paragraphs contain a few examples.
EXAMPLE 1:
Play video on the VCR (source) in the living room and watch
the picture on the TV (destination) in the bedroom.
Connect the TRANSMITTER to the VCR an the RECEIVER to the TV in the be room. Switch on the vi eo an insert a
tape. Place the IR eye on / in front of the IR receiver of the VCR. Switch on the TV in the be room.
Select the mo e on the TV for “Line In” (AV, EXT or channel 0). Aim the VCR remote control to the IR eye an press
play. The vi eo shoul start playing an picture an soun shoul appear on your be room TV screen.
EXAMPLE 2:
If you do not have coax cable connection with the TV in the bedroom
you can tune in the channels on your VCR (source) in the living room
and watch the picture on the TV (destination) in the bedroom.
You may nee the manual of your VCR to tune in the TV channels.
Once all channels are tune in, you are able to watch your TV channels through your AV channel.
Connect the TRANSMITTER to the VCR an the RECEIVER to the TV in the be room. Switch on the vi eo.
Place the IR eye on / in front of the IR receiver of the VCR. Switch on the TV in the be room. Select the mo e
on the TV for “Line In” (AV, EXT or channel 0). You can take the remote of your VCR to your be room to control
your TV channels tune in your VCR.
EXAMPLE 3:
Also, if you do not have coax cable connection with the TV in the bedroom,
the AV ender gives the possibility to view your atellite Receiver (source) programs
also on the TV (destination) in the bedroom.
You probably alrea y tune in the channels on your Satellite Receiver. If not, you may nee the manual of your Satellite
Receiver to tune in the TV channels. Once all channels are tune in, you are able to watch your TV channels through
your AV channel (or other output channel). Connect the TRANSMITTER to the Satellite Receiver an the RECEIVER
to the TV in the be room. Switch on the Satellite Receiver. Place the IR eye on / in front of the IR receiver of the
Satellite Receiver. Switch on the TV in the be room. Select the mo e on the TV for “Line In” (AV, EXT or channel 0).
You can take the remote of your Satellite Receiver to your be room to control your TV channels tune in your Satellite
Receiver.
Getting tarted
SV_1716_AV_Sender UK 15x17:SV_1715_AV_Sender 17 talen 05-11-2007 12:09 Pagina 6

WWW.ONEFORALL.COM 7
Problem & olution
If your house has a heavy metal construction or is equipped with a PC network, it can disturb the radio
signal. Even moving the units a few inches can improve the performance. If this doesn’t work try to move
the TRAN MITTER and RECEIVER to another place in the house. If you experience problems, try placing the
units away from electrical appliances.
• No picture on second TV.
- Make sure that the TRANSMITTER an RECEIVER are switche ON.
- Make sure that both TRANSMITTER UNIT an RECEIVER UNIT are set to the same channel.
- Select “EXT” or “AV” on secon TV.
- Make sure that all cables are connecte correctly.
- Make sure that the vi eo source (satellite receiver, vi eo recor er, camcor er, DVD player,
igital or analogue Set-Top Box or Pay-TV eco er box) is switche on.
- Make sure to use the correct SCART connector (e.g. EXT1 or EXT2) of the vi eo source
(check manual of vi eo source).
• Bad picture/ sound quality on second TV.
- Try to fin out if the way the cables are place cause interference.
- Make sure that the istance between the TRANSMITTER an RECEIVER unit is less than 100 ft (30 m).
• Picture of selected TV channel disappears (snow-picture).
- Disable the auto stan by mo e of the VCR (check the manual of the VCR how to o this).
• The picture on your second TV is not correct.
- Select “EXT” or “AV” on secon TV.
- Make sure that the vi eo source is switche on.
• Using a remote control, you cannot control the video source from your second TV.
- Aim the remote control irectly at the Remote Control Exten er Eye an ensure that there are no obstacles in
between.
- Ensure that there is no other wireless evice (wireless hea phones, speakers, RF control signals)
interfering with the remote control.
- Make sure that TRANSMITTER an RECEIVER are more than 16 ft (5 m) apart.
- Make sure to use the remote control of the vi eo source.
- Reposition the IR Eye on the vi eo source OR place the IR Eye 2 - 4 inch (5 - 10 cm) in front of the vi eo source.
• Buzzing sound when using the remote control
- With some types of TV you will not be able to solve this problem.
• -VH video shows no colour pictures (only black and white).
- Select CVBS vi eo output format for your S-VHS VCR
• DVD player gives no pictures on either main- or second TV.
- Select CVBS vi eo output format for your DVD player (check the DVD player’s user manual.
Trouble hooting
SV_1716_AV_Sender UK 15x17:SV_1715_AV_Sender 17 talen 05-11-2007 12:09 Pagina 7

SV 1716
706682
Guarantee English UNIVERSAL ELECTRONICS / ONE FOR ALL warrants to the original purchaser that this pro uct will be free from efects in materials an workmanship un er normal an correct use for a perio of one (1) year
from the ate of original purchase. This pro uct will be repaire or if necessary replace free of charge if it has been proven to be efective within the one (1) year warranty perio . The forwar ing costs are on the account of the
owner; the costs of returning the pro uct are on the account of UNIVERSAL ELECTRONICS / ONE FOR ALL. This warranty oes not cover amage or failures cause by pro ucts or services not supplie by UNIVERSAL ELECTRONICS /
ONE FOR ALL, or which result from not mounting the pro uct accor ing to manual instructions. This also applies when the pro uct has been mo ifie / repaire by others than UNIVERSAL ELECTRONICS / ONE FOR ALL or if a fault is
the result from acci ent, misuse, abuse, neglect, mishan ling, misapplication, faulty installation, improper maintenance, alteration, mo ifications, fire, water, lightning, natural isasters, wrong use or carelessness. To obtain warranty
service uring the warranty perio , please notice that we nee your original purchase receipt so that we may establish your eligibility for service. If you have bought this pro uct for purposes which are not relate to your tra e,
business or profession, please remin that you may have legal rights un er your national legislation governing the sale of consumer goo s. This guarantee oes not affect those rights.
Un versal Electron cs BV
Europe & Internat onal
P.O. Box 3332
7500 DH, Enschede
The Netherlands
RDN 1051107
Declaration of Conformity
We, Universal Electronics Inc., 6101 Gateway Drive, Cypress, CA 90630, U.S.A., an its subsi iaries
Universal Electronics BV, Institutenweg 21, 7521 PH Ensche e, Netherlan s,
ONE FOR ALL GmbH, Fabrikstra_e 3, 48599 Gronau, Germany,
ONE FOR ALL UK Lt , Institutenweg 21, 7521 PH Ensche e, Netherlan s,
ONE FOR ALL FRANCE S.A.S., Rue Paul Séramy 17, 77300 Fontainebleau, France,
ONE FOR ALL IBERIA S.L., Ctra. Hospitalet, 147-149, 08940 Cornellá e Llobregat, Barcelona, España,
ONE FOR ALL ARGENTINA S.R.L., AV. Las Heras 2126, 5th Floor (Suite “C”) ZC 1111, Recoleta, Buenos Aires, Argentina
Declare un er sole responsibility that the ONE FOR ALL Wireless Au io/Vi eo Sen er (SV-1716)
is in conformity with the essential requirements as escribe in Directive 1999/5/EC an satisfies all the technical
regulations to the pro uct within this irective.
EN 300 440-1 (V1.3.1)
EN 300 440-2 (V1.1.2)
EN 301 489-1 (V1.6.1)
EN 301 489-2 (V1.4.1)
EN 50371 (2002)
IEC 60065 (2002)
Ensche e, 02 October 2007
Paul J. Bennett
As Managing Director of Universal Electronics BV
0678
SV_1716_AV_Sender UK 15x17:SV_1715_AV_Sender 17 talen 05-11-2007 12:09 Pagina 8