OneFex CE-IO1600 User manual

1
/ 13
CE-IO1600 User Manual
CE-IO1600
Ethernet I/O Module
Manual

2
/ 13
CE-IO1600 User Manual
1PRODUCT INTRODUCTION............................................................................................... 5
1.1 Features ...........................................................................................................................................5
1.2 Parameter.........................................................................................................................................5
1.3 Item Selection .................................................................................................................................6
1.4 Dimension........................................................................................................................................6
2WIRING INSTRUCTIONS..................................................................................................... 6
2.1 Terminal Definition.........................................................................................................................6
2.2 RS485 Communication Wiring.....................................................................................................6
2.3 DO Wiring.........................................................................................................................................7
3ETHERNET CONFIGURATION&COMUNICATION TEST........................................ 7
3.1 Ethernet Parameter Config...........................................................................................................7
3.1.1 Direct mode ........................................................................................................................................ 7
3.1.2 Networking mode............................................................................................................................. 11
3.1.3 TCP/UDP Configuration..................................................................................................................14
3.2 Communication Test....................................................................................................................18
3.2.1 Test Software...................................................................................................................................18
3.2.2 Network Test Tool............................................................................................................................18
3.2.3 Modbus TCP Testing ......................................................................................................................25
3.3 Device Address.............................................................................................................................28
3.3.1 Download..........................................................................................................................................28
3.3.2 Revise Address................................................................................................................................28
3.4 PLC Communication....................................................................................................................28
4DEVELOPMENT DATA INSTRUCTION........................................................................29
4.1 Flash On Flash Off Mode ............................................................................................................29
4.2 Modbus Register Instruction......................................................................................................29
4.3 Command List...............................................................................................................................31
4.4 Command Details.........................................................................................................................32
4.4.1 Control DO........................................................................................................................................ 32
4.4.2 Query DO Status .............................................................................................................................32
4.4.3 Flash ON Flash OFF Command....................................................................................................33
4.4.4 All ON and All OFF Command.......................................................................................................34
5PRODUCT MAINTENANCE..............................................................................................34

3
/ 13
CE-IO1600 User Manual
5.1 Device Usage Environment ........................................................................................................34
6AFTER-SALE SERVICE.....................................................................................................34
6.1 Commitment..................................................................................................................................34
6.2 Disclaimer......................................................................................................................................35
7UPDATE HISTORY...............................................................................................................35

4
/ 13
CE-IO1600 User Manual
Notice
❖Please read this manual carefully before use and save it for reference.
❖Please follow to the operating procedures and precautions in this manual.
❖Please open the package carefully and check whether the device and accessories have been
damaged due to transportation when you receive the device.
Please contact us for return processing once damage occurs.
❖Please do not repair it yourself, and contact our technical support department directly if the
device fails.
❖Manual and Config Tool download link:
https://onefexindustrial.com/ethernet-io-module

5
/ 13
CE-IO1600 User Manual
1 Product Introduction
CE-IO series products are Ethernet I/O module using standard Modbus RTU/TCP protocol,
integrates DO (digital output), DI (digital input), AI (analog input).
The communication method supports Ethernet networking, 7~40V wide voltage power
supply, and supports functions such as logic control between analog acquisition and relay
output.
Widely used in farms, agricultural greenhouses, IoT terminals, water conservancy,
electricity, gas collection and control and other application scenarios, its unique logic control
function can easily realize automatic water supply, fertilization, start and stop valves It is an ideal
device for small automatic control scenes.
1.1 Features
◆DC 7-40V wide voltage power supply, support anti-reverse connection;
◆16* DO contact isolation, normally ON and normally OFF, 10A 250VAC / 10A 30VDC;
◆LED indication, 1 for power and working status; 16 leds for DO status;
◆SupportsRS485+EthernetCommunicationinterface,powerisolationplussignalisolation,reliable
communication;
◆Communication baud rate: 300bps~38400bps (, It is 9600 by default and can be
modified by software);
◆Supportstandard ModbusRTU/TCPprotocol,readand write by registeraddress;
◆Support input and output linkage, such as local linkage or dual-computer linkage, which is
convenient for multi-terminal control;
◆Support flash ON flash OFF;
◆Supporting setting software for setting parameters and IO control;
◆Support software and hardware customization.
1.2 Parameter
Paremater
Contact capacity
10A/30VDC;10A/250VAC
Durability
100,000 times (Electrical）
10,000,000 times (Mechanical)
Data interface
RS485/Ethernet
Default IP
192.168.16.254
Working Voltage
DC 7-40V
Power / work indication
1 red LED
(power, always on; working, flashing)
Output indication
16 red LEDs (relay on and off)
Working temperature
-40℃～85℃, Industrial Grade
Size
180*94*41mm
Weight
450g
Default communication format
9600,n,8,1
Baud rate
300~38400bps
Software support
Setting and control software;
Support various configuration software;
support Labviewd, etc.

6
/ 13
CE-IO1600 User Manual
Installation
35mm Din Rail Mounting / Screw Holes
1.3 Item Selection
CE-IO0222
2*DI&2*DO&2*AI, RS485+Ethernet, Modbus RTU/ TCP/UDP/MQTT
CE-IO0222S
2*DI&2*DO&2*AI, RS485+Ethernet, Modbus RTU/ TCP/UDP/MQTT,
Timing Control, DI/AI&DO Linkage
CE-IO0222SC
2*DI&2*DO&2*AI, RS485+Ethernet, Modbus RTU/ TCP/UDP/MQTT,
Timing Control, DI/AI&DO Linkage, Cloud
CE-IO4444
4*DI&4*DO&4*AI&4*AO, RS232+Ethernet, Modbus RTU/
TCP/UDP/MQTT, Timing Control, DI/AI&DO Linkage
CE-IO1600
16*DO, RS485+Ethernet, Modbus RTU/ TCP/UDP/MQTT
1.4 Dimension
180*94*41mm
2 Wiring Instructions
2.1 Terminal Definition
2.2 RS485 Communication Wiring

7
/ 13
CE-IO1600 User Manual
2.3 DO Wiring
3 Ethernet Configuration&Comunication Test
3.1 Ethernet Parameter Config
Ethernet
IP Address
Network
Mode
Port#
Device
Address
192.168.1.232
TCP
Server
10000
1
There are 2 modes for ethernet parameter configuration
Hardware
Connection
Instuctions
Direct mode
The io is directly connected to computer
through a network cable
Networking mode
The io is connected to the router/switch via a
network cable
3.1.1 Direct mode
Open [Network and Sharing Center]---->[Change Adapter Settings]---->[Local Area Connection]--
-->[Properties]---->[IPV4], modify the computer IP to static IP: 192.168.1.10;
(Because the default IP of io is 192.168.1.232, when modifying its parameters, the io IP must be
in the same network segment as the computer IP.

8
/ 13
CE-IO1600 User Manual
➢Open JYNetConfigEn, it shows as below:

9
/ 13
CE-IO1600 User Manual
➢Chosse Local connection：
➢Searching：

10
/ 13
CE-IO1600 User Manual
➢Revise parameter
➢researching

11
/ 13
CE-IO1600 User Manual
3.1.2 Networking mode
Check to make sure that the computer network and the router/switch connected to io are in
the same network.
Note: generally, there are multi-level networks in the enterprise. When the computer is
connected to the wireless network and the io is connected to the router through a network
cable, it must be confirmed that the router connected to the io is the same as the wireless
WIFI router.
➢searching；
➢View current network information
Open [Network and Sharing Center]---->[Active Network]---->[Local Area Connection/Wireless
Network Connection]---->[Details], as shown in the following figure:

12
/ 13
CE-IO1600 User Manual
➢Check whether the IP to be modified by the device is occupied

13
/ 13
CE-IO1600 User Manual
➢Revise IP

14
/ 13
CE-IO1600 User Manual
➢Researching
3.1.3 TCP/UDP Configuration
Mode
Instruction
TCP Server
①The device is used as the server side;
②Support two Clients to use different port numbers to communicate
with the device.
TCP CLient
①The device is used as the Client;
②It can be set to communicate with two different server addresses;
③Support setting handshake packets and heartbeat packets
UDP Server
①The device is used as the server side;
②Support setting two clients to use different port numbers to
communicate with the device
UDP Client
①The device is used as the Client;
②It can be set to communicate with two different server addresses;

15
/ 13
CE-IO1600 User Manual
3.1.3.1 TCP Server
3.1.3.2 TCP Client
➢Mode revisement

16
/ 13
CE-IO1600 User Manual
➢Login information packet (handshake packet)
When using the TCP Client mode, the device will send a handshake message when connecting
to the server for the first time as a client, which can be customized and modified.
➢Heartbeat packet

17
/ 13
CE-IO1600 User Manual
3.1.3.3 UDP Server
3.1.3.4 UDP Client

18
/ 13
CE-IO1600 User Manual
3.2 Communication Test
Working Mode
Test software/method
TCP Server
JYNetConfigEn
Network Test Tool
TCP Client
JYNetConfigEn
Network Test Tool
UDP Server
/
Network Test Tool
UDP Client
/
Network Test Tool
3.2.1 Test Software
JYNetConfigEn
Download link：
https://onefexindustrial.com/ethernet-io-module
3.2.2 Network Test Tool
➢Ethernet IO support Modbus RTU and Modbus TCP two communication protocols.
➢For commands used in the test process, please refer to the manual of corresponding device
model.
3.2.2.1 TCP Server Mode
Connection Example：
◆IO Parameter

19
/ 13
CE-IO1600 User Manual
◼Create a device-oriented iP and port in TCP Client mode:
◆Send command test

20
/ 13
CE-IO1600 User Manual
3.2.2.2 TCP Client Mode
Connection Example：
◆IO Parameter
◆Create a TCP Server and listen on port 10000: