ProSoft Technology Wireless I/O System User manual

Wireless I/O System
May 6, 2016
QUICK START GUIDE

Your Feedback Please
We always want you to feel that you made the right decision to use our products. If you have suggestions, comments,
compliments or complaints about our products, documentation, or support, please write or call us.
How to Contact Us
ProSoft Technology, Inc.
9201 Camino Media, Suite #200
Bakersfield, CA 93311
[phone]
[phone] (Fax)
http://www.prosoft-technology.com
[email protected]
Copyright © 2016 ProSoft Technology, Inc. All rights reserved.
Wireless I/O System Quick Start Guide
May 6, 2016

Wireless I/O System ♦ Contents
Quick Start Guide
ProSoft Technology, Inc. Page 3 of 14
May 6, 2016
Contents
Your Feedback Please........................................................................................................................2
How to Contact Us..............................................................................................................................2
1Overview 5
2Basic Setup 7
2.1 Typical Installation.....................................................................................................9
2.2 I/O Chain Diagram.....................................................................................................9
2.3 Power ......................................................................................................................10
3Specifications 11
3.1 Radio.......................................................................................................................11
3.2 Digital.......................................................................................................................12
3.3 Analog 4-20 mA.......................................................................................................13
3.4 Analog 0-10 V..........................................................................................................14

Wireless I/O System ♦
Quick Start Guide
ProSoft Technology, Inc. Page 4 of 14
May 6, 2016

Wireless I/O System ♦ Overview
Quick Start Guide
ProSoft Technology, Inc. Page 5 of 14
May 6, 2016
1 Overview
This guide provides basic information to assist you in quickly getting started.
Go to http://www.prosoft-technology.com/ to download the full User Guide for
detailed installation and other helpful information. Advanced User Interface
software is also available at the site for download.
Warning 1: Ensure installation of the system meets applicable state and national electrical code
requirements. The installation of the system should only be performed by a qualified installer or a
factory representative.
Warning 2: To prevent ignition of flammable or combustible atmospheres, disconnect power
before servicing.
Caution: The system must be installed within an enclosure that requires a tool to access. This is to
prevent inadvertent disconnection of any of the power wiring, signal wiring or communication
cables.
Caution: EXPLOSION HAZARD. Do not disconnect equipment unless power has been switched
off or the area is known to be non-hazardous.
Caution: EXPLOSION HAZARD. Do not remove or replace fuse when energized.
Note: This equipment is designed for use in Class I, Division 2 (Zone 2) or non-hazardous
locations only.

Wireless I/O System ♦
Quick Start Guide
Page 6 of 14 ProSoft Technology, Inc.
May 6, 2016

Wireless I/O System ♦ Basic Setup
Quick Start Guide
ProSoft Technology, Inc. Page 7 of 14
May 6, 2016
2 Basic Setup
1. Attach DataRail™ and End Terminal Bracket to 35 mm x 7.5 mm DIN
Rail. (Attach components from left to right without a gap)
2. Attach Radio module and connect antenna. (Lightning arrestor is optional)
3. Attach I/O module(s) and set slave IDs. When using more than a 5-
module combination per radio, use the Power Budget Calculator to
determine maximum I/O module capacity. http://psft.com/A5D

Wireless I/O System ♦
Quick Start Guide
Page 8 of 14 ProSoft Technology, Inc.
May 6, 2016
4. Cover unused DataRail slots.
5. Terminate I/O and power supply as required. Use solid or stranded wire
(AWG) 28-12. Always disconnect power when attaching or detaching I/O
module(s) to or from DataRail to avoid damage.
Note: The power leads to the 9-30 VDC power terminals should be kept to a maximum of
1 meter in length.

Wireless I/O System ♦ Basic Setup
Quick Start Guide
ProSoft Technology, Inc. Page 9 of 14
May 6, 2016
2.1 Typical Installation
2.2 I/O Chain Diagram

Wireless I/O System ♦
Quick Start Guide
Page 10 of 14 ProSoft Technology, Inc.
May 6, 2016
2.3 Power

Wireless I/O System ♦ Specifications
Quick Start Guide
ProSoft Technology, Inc. Page 11 of 14
May 6, 2016
3 Specifications
3.1 Radio

Wireless I/O System ♦
Quick Start Guide
Page 12 of 14 ProSoft Technology, Inc.
May 6, 2016
3.2 Digital

Wireless I/O System ♦ Specifications
Quick Start Guide
ProSoft Technology, Inc. Page 13 of 14
May 6, 2016
3.3 Analog 4-20 mA

Wireless I/O System ♦
Quick Start Guide
Page 14 of 14 ProSoft Technology, Inc.
May 6, 2016
3.4 Analog 0-10 V