ICW ULTRA User manual

Page 1
ULTRA ARM INSTALLATION
ULTRA ARM INSTALLATION - 5/21/20
Page 1 of 4
IF MOUNTING TO THE ULTRA WALL TRACK
IF MOUNTING TO A DESK
Screw stud
into desk mount
Desk Desk
Washer
Nylock
ADJUST SLIDER POSITION
• Remove small socket head cap screw in the top
center of the Wall Track. Remove plastic cover.
• Locate the wall stud and mark the top hole of the
Wall Track.
• Drill 11/64 pilot hole, insert #14 screw and tighten
slightly. Use a level, mark the lower holes, drill
pilot holes and then insert the #14 screws.
NOTE: #14 Wood screws are supplied with unit. If installing into
metal studs, you will need to replace these with proper metal
stud fasteners
MOUNT ULTRA TRACK TO WALL
MOUNT ULTRA TRACK TO WALL
• Remove small socket head cap screw in the top center of
the Wall Track. Remove plastic cover.
• Locate the wall stud and mark the top hole of the Wall Track.
• Drill 11/64 pilot hole, insert #14 screw and tighten slightly.
Use a level, mark the lower holes, drill pilot holes and then insert
the #14 screws.
NOTE: #14 wood screws are supplied with unit. If installing into
metal studs you will need to replace these with proper metal
stud fasteners or the provided snap togglers. All hardware used
to secure track mount must have a proper countersunk head.
Desk Mount
Part Number
Stud
Length
Maximum
Desk Thickness
D0 3.50” 2.47”
D1 3.50” 1.87”
D3 5.50” 1.87”
D5 7.50” 1.87”
D7 10.50” 2.38”
• Drill a 3/8" hole through the
horizontal mounting surface.
• Screw stud into base of desk mount.
• Push the stud on the desk mount
through the hole.
• Slide the large mounting washer
over the stud from underneath.
• Secure in place with 3/8” nylock nut.
ATTACH SLIDER TO ULTRA TRACK
• Insert slider into
wall track.
• Replace the
small socket
head cap
screw and
plastic cover.
Adjust slider to desired height. Tighten slider using adjustment knob.
ADJUST SLIDER POSITION
STANDARD INVERTED
Adjust slider to desired height. Tighten slider using adjustment knob.
ADJUST SLIDER POSITION
STANDARD INVERTED
Adjust slider to desired height. Tighten slider using adjustment knob.
ADJUST SLIDER POSITION
STANDARD INVERTED
STANDARD INVERTED
• Insert slider into wall track.
• Replace the plastic cover
and small socket
head cap screw.
Once you have
adjusted the slider
to the desired height,
tighen down the Track
Slider using the knob
on the slider as shown.
Adjust slider to desired height. Tighten slider using adjustment knob.
ADJUST SLIDER POSITION
STANDARD INVERTED

ULTRA ARM INSTALLATION - 5/21/20Page 2 of 4
IF MOUNTING TO A POLEIF MOUNTING TO A WALL
IF MOUNTING TO AN MD TRACK
ATTACH
UL510
TO W2,
W3 OR W5
ATTACH
PARALINK
TO W2,
W3 OR W5
Attach to UL510 to
W2 wall mount using
3/8 bolt assembly
and 1.25” bearing
assembly provided.
Insert bolt assembly
up through wall ear.
Place 1.25” bearing
assembly over bolt
on the other side
of wall ear. Place
UL510 over bolt and
bearing and turn bolt
until UL510 is secure
and smoothly turns
against the bearing.
Attach to Paralink to
W2 wall mount using
3/8 bolt assembly
and 1.25” bearing
assembly provided.
Insert bolt assembly
up through wall ear.
Place 1.25” bearing
assembly over bolt
on the other side
of wall ear. Place
Paralink over bolt
and bearing and turn
bolt until Paralink is
secure and smoothly
turns against the
bearing.
ATTACH WALL PLATE TO WALL ATTACH WALL PLATE TO WALL
MOUNT WALL PLATE TO MD TRACK
W2
Locate the stud and
mark the top hole, drill
11/64 pilot hole and
insert #14 screw and
tighten slightly. Using
a level, mark the lower
hold and drill pilot hole,
insert #14 screw and,
with the unit level,
tighten both screws.
NOTE: ICW supplies
#14 wood screws. If
installing onto metal
studs, you will need
to replace with proper
metal stud fasteners.
W3
UL510
Paralink
Beauty cap
Beauty cap
1.25”
ID bearing
assembly
1.25”
ID bearing
assembly
3/8 bolt
assembly
with 3/8
ID bearing
3/8 bolt
assembly
with 3/8
ID bearing
W2 W2
ATTACH
UL500
TO W2,
W3 OR W5
Attach to UL500 to
W2 wall mount using
3/8 bolt assembly
and 1.25” bearing
assembly provided.
Insert bolt assembly
up through wall ear.
Place 1.25” bearing
assembly over bolt
on the other side
of wall ear. Place
UL500 over bolt and
bearing and turn bolt
until UL500 is secure
and smoothly turns
against the bearing.
UL500
Beauty cap
1.25”
ID bearing
assembly
3/8 bolt
assembly
with 3/8
ID bearing
W2
Using the 1/4″ hex
key, separate the
two halves of pole
mount as shown,
place around pole
at the desired height
and reassemble.
ICW recommends wood or metal stud mounting only.
W2 W3 W5
Use a level to be sure mount is correctly aligned.
• Install track as per MD track
installation.
• Loosely attach track adapters
to wall ear (W2, W3 or W5).
• Slide wall ear with loosely
attach track adapters into MD
track.
• Once in desired position,
tighten one track adapter with
5/32 Allen wrench.
• Check to ensure wall ear is
level and tighten remainder or
track adapters.

ULTRA ARM INSTALLATION - 5/21/20
Page 3 of 4
ATTACH VESA TO UL 500
Mount the
VESA assembly
to the friction
mount by sliding
the connecter into the UL500
pivot block. Using the 5/32” hex
key, secure fl at head screw back
into place.
ATTACH VESA TO MONITOR
Attach the
VESA plate to
your monitor
using the four
4mm screws in
the hardware bag.
ADJUST TILT HANDLES
Use the handles to adjust
the tilt of the monitor.
IF USING UL550
IF USING UL500
ATTACH TO MONITOR
Attach your monitor to the VESA
plate user the four 4mm screws in
the hardware bag.
MONITOR TILT, ROTATION
& ADJUST MONITOR DEPTH
MONITOR TILT
& ROTATE
Gently hold sides
of monitor. Tilt and
rotate to desired
position with ball
VESA.
ADJUST
MONITOR
DEPTH
Loosen the
adjustment
knob, move
the Paralink
forward or
back, then
re-tighten
the knob.
Adjustment
Knob
Pivot tension
adjustment
screws
Use the slider knob to
loosen the slider to adjust
the height of the monitor
on the Paralink.
Adjust the pivot tension
of the ball by gently and
evenly tightening or
loosening the four
screws on the back
of the ball VESA.
Slider knob
ADJUST BALL VESA
TENSION & HEIGHT
ATTACH
PARALINK
TO W2,
W3 OR W5
Attach to Paralink
to Ultra arm using
3/8 bolt assembly
and 1.25” bearing
assembly provided.
Insert bolt assembly
up through wall ear.
Place 1.25” bearing
assembly over bolt
on the other side
of wall ear. Place
Paralink over bolt
and bearing and turn
bolt until Paralink is
secure and smoothly
turns against the
bearing.
Paralink
1.25”
ID bearing
assembly
3/8 bolt
assembly
W2
Beauty cap

ULTRA ARM INSTALLATION - 5/21/20Page 4 of 4
ULTRA CORD MANAGEMENT
1.Prepare all cables to route within the arm by placing them
near cavity of arm and bundling together if necessary.
2.Remove cover by unscrewing four socket head cap screws.
Screws are captured by the cover so they cannot fall out.
Once screws are disengaged, pull cover out of arm.
3.Place cables within the channel. Do not block the holes
where screws will engage in arm.
4.Replace cover and tighten screws. Cables should be able to
pull through to desired position if necessary.
IF USING PARALINK KEYBOARD TRAY IF USING ULTRA KEYBOARD TRAY
IF USING UL510
ADJUST TILT & MONITOR HEIGHT
Use the handles to
adjust the tilt of the
monitor.
Adjust the height of
the monitor along
the rails of the 510.
Then tighten in
place using slider
knob.
Slider Knob
ATTACH VESA
Mount the VESA
assembly to the slide
rail by screwing in
the knob through the
rail into the VESA
assembly as shown.
ATTACH TO MONITOR
Attach your monitor to the VESA
plate user the four 4mm screws in
the hardware bag.
ATTACH FLIP UP
1.Remove screws from
drop extension using
5/32” hex key.
2.Align holes in keyboard
tray with screw holes in
drop extension.
3.Attach keyboard tray
using the provided
screws.
ATTACH PARALINK
1.Remove beauty cap on
Paralink.
2.Remove screw using 3/16”
hex key.
3.Slide keyboard tray into
Paralink.
4.Replace screw and tighten.
5.Replace beauty cap.
Beauty cap
Screw
NOTICE: ICWUSA.COM, Inc. provides the appropriate hardware fasteners to
match the majority if not all standard monitors and devices. It is the responsibility
of the installer / integrator to ensure that the screws and fasteners have the
adequate thread engagement. The rule of thumb is that the thread depth is greater
than the diameter of the hole or 4 full turns of 360 degrees of thread engagement.
It is also the responsibility of the installer / integrator to ensure that they do not
damage the monitor or device by using a screw or fastener that is too long for hole
and therefore damaging the unit by inserting too far.
When cleaning your ICW mounting unit please follow the points below. Proper
cleaning of the mounting device will help assure proper function and extend the
life of the unit.
1. Any general cleaner is acceptable except degreasers are not recommended near
the bearing entrances.
2. Spray cleaner or water on a soft cloth or paper towel and then wipe down
the mounts.
3. Do not spray directly at the bearing seams (located at all swivel points) as this could
reduce the life of the bearings.
CLEANING OF THE ICW MOUNTING DEVICE