OneScreen OSB2MPF4AI User manual

Qualcomm products contained herein are products of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. The
Made with Qualcomm Technologies logo is a trademark of Qualcomm Incorporated
Full hd Bullet
AI-BASED CAMERA

Model: OSB2MPF4AI
INSTALLATION GUIDE

PRODUCT KIT
Installation guide Drilling position decal
Ø 5 mm 4 Holes
CAMERA FRONT
TEMPLATE
3
Qualcomm products contained herein are products of QualcommTechnologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registeredin the United States and other countries. The
Made with Qualcomm Technologies logo is a trademark of Qualcomm Incorporated
Full hd Bullet
AI-BASED CAMERA
Camera Hex tool
Set 4 of screws
and anchors
Wi-Fi Antenna

TECHNICAL SPECIFICATION
4
Protection standards IP66
Optical zoom Fixed-focal
Focal length OSB2MPF4AI: 4 mm
OSB2MPF4AI: 87.5° (H) - 104.9° (D) - 44.4° (V)Angle of view
Resolution, frame rate
14°F - 140°F
Operating temperature
Humidity: 10% ~ 100%
Dimensions (L x W x H) 6.4” x 3.2” x 2.4” (in)
Weight 5.5 lbs
H.264/H.265
FHD 1920x1080, 30 fps
Power
Power consumption
DC12V/1A: Maximum 8.6W
PoE: Maximum 9.1W
DC12V/1A / PoE (IEEE802.3af)

PRODUCT OVERVIEW
5
12 VDC power supply
RJ45 terminal block
Reset
Camera lens
Audio out
Audio in

INSTALLATION GUIDE
Step 1: Apply decal on the area where the camera needs to be installed and fix the plastic anchors (figure 1).
Step 2: Tighten the screws to fix the camera (figure 2).
1 2
6

7
INSTALLATION FOR SIGNAL CONNECTION
Two options to connect devices:
Use the network cable con nected from the PoE switch to the waiting RJ45
port, no need to use 12VDC (figure 1).
1
RJ45
Switch PoE

8
ADJUSTING THE CAMERA VIEWING ANGLE
130°
65°

9
ACCESSING THE CAMERA
For additional security, please do not repeat any characters in your password.
If you forget your password, you can hold the [RESET] button to return the product to its factory
settings.
Note:
Password setting
Using your web browser, access the camera's default IP: 192.168.1.168
Note: To complete the installation steps for the camera, refer to the User Manual.
The system will ask you to reset the password on your initial access.
When the "Administrator password change" window appears, enter a new password.
For passwords using eight or nine characters, you need to use at least three of the following types of
characters: uppercase and lowercase letters, numbers, and special characters.
For passwords using 10 to 15 characters, you need to use at least two of the character types.
Special characters include: ~ ` ! @ # $ % ^ & * ( ) _ - = + | { } [ ] . ? /
User name
Password
Administrator password change
New password
Confirm new password
For a new password with 8 to 9 digits, you must use at least 3 of the following:
uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15
digits, you must use at least 2 types of those mentioned.
For higher security, you are not recommended to repeat the same characters or consecutive
keyboard inputs for your passwords.
If you lost your password, you can press the [RESET] button to initialize the product. So, don’t lose
your password by using a memo pad or memorizing it.
Special characters that are allowed: ~`!@#$%^*()_-+=|{}[].?/

10
SOFTWARE INSTALLATION
Login screen
When accessing the camera, a login window will appear.
Enter your user name and password to access the camera.
1. Enter "admin" in the <User name> box.
2. Enter your chosen password in <Password> box.
3. Click
User name
Password

11
For information about OneScreen product warranty and thereto related information, go to
onescreensolutions.com/en/warranty
WARRANTY INFORMATION
SAFETY INFORMATION
Be sure to follow this advice to ensure the device works properly.
It is recommended to use shielded network cables (STP) during set-up.
It is recommended to use CAT5e or higher network cables.
Store the camera in a cool and dry environment.
Shield the camera from potential impact from heavy objects.
Do not install the camera on unstable pillars, brackets, surfaces, or walls.
Do not use chemicals or detergents to clean the camera or housing.
To clean, use a damp cloth.
Only use standard tools and accessories when installing the camera equipment. The manufacturer
recommends using the manufacturer's power supply equipment or a corresponding source for the
camera. Improper installation may cause damage to the product.
Contact OneScreen customer support or authorized OneScreen agents if you experience any problems.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limit are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
a accordance with the instruction manual, may cause harmful interference to radio communications.
Operations of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Precautions:
Use the original packaging, or equivalent, to avoid damaging the product during transportation.
Transportation:

OneScreen
Address: 12335 World Trade Drive, Suite 9, San Diego, CA 92128
Website: www.onescreensolutions.com
Email: [email protected]