Onida Sparkle 65X User manual

Before operating the Washing Machine, Please read
this Guide thoroughly, and retain for future reference.
65X
USER'S MANUAL
Fully Automatic
WASHING MACHINE

SAFETY PRECAUTION
FEATURES
FAMILIARISATION WITH CONTROL PANEL
PARTS LOCATION AND IDENTIFICATION
INSTALLATION & PREPARATION
CONNECTING THE DRAIN HOSE
PREPARATION BEFORE WASH
WASHING PROCEDURE
SELECTABLE WASHING METHODS
MAINTENANCE
TROUBLE SHOOTING
GUIDELINES FOR SAFETY AND DURABILITY
ONIDA SERVICE CENTRES
SPECIFICATIONS
WARRANTY CARD
1
2-3
4-5
6
7
8
9
10-11
12
13
14
15
16
17
Contents :
Dear Customer ,
SPARKLE 65X
Proper use of Washing Machine Saves Electricity & Time
Congratulations! You are now a proud owner of Onida SPARKLE 65X
Fully automatic Washing Machine. We would particularly advise you
to study the User's manual carefully to get the best out of your Onida
Machine and please take the precautions mentioned on the following
pages.
Once again, Welcome to the happy ONIDA family.

Safety Precautions
Safety Precautions
-1-
Do not use water with temperature exceeding 50 C, as this deforms the
plastic parts in the machine. If you desire to use warm water add hot water
to cold water in the wash tub. Do not pour hot water in an empty tub.
0
Keep the machine away from flames and inflammable material. Do not
expose the washing machine to direct sunlight or rain. Also avoid placing it
in humid locations.
Make sure that the washing machine is plugged to a 5A
electrical outlet and earth terminal is provided on the outlet.
Unplug the power supply cord when you do not use it.
To disconnect the washing machine from electrical mains completely, pull out
the plug and never pull it from the mains cord.
Don't allow your kids to look into the inside of the washing machine.
This washing machine is meant for washing clothes with water as a medium.
Do not use petrol or other chemicals. This can result in fire and damage.
Take caution not to pierce the control panel membrane sheet.
Never connect the earth wire to a phone wire, lightning rod.
Do not press the button with an awl or pin.
Never wash the washing machine or spread the water on machine top.
Clean with just wet cloth or cloth soaked in soap water.
Please note that the following precautions for safety intend to
prevent unpredictable danger and damage by helping the
Proper use in safety.

Features
Features
-2-
Features
Features
Moving Digital Display
Brush
Water Saver Program
Hexo Drum
Multiple Water Inlets
Magic Filter
In this Program t
Keeps you updated with the various wash cycle timings and stages. Also easily
allows you to program your machine with times and cycle repetitions according
to your convenience and requirements.
With an actual Brush fitted on the inside of your drum, your clothes are treated
gently with a cleaning system which is very much like a real person giving it a
hand wash
he rinse function com ines the spin and water spray features
to help save energy and reduce water consumption y approximately 35%.
With 2 water inlets provided, you can always e connected to cold & hot water
sources. You can also choose the temperature of the water - hot, cold or a mix
of oth ased on the requirement of your clothes to enhance the cleaning potential
of the machine.
The strategically placed ox-type Magic Filter makes excess lint on your clothes
history. It is positioned on the lower level of the tu which means that even in
small wash loads the fluff will e captured in the Magic Filter and your clothes
will remain lint-free.
The Hexo Drum design creates a protective arrier of water etween the drum
and clothes. This ensures that your clothes get the est wash with minimum
damage.
Waterfall
Fuzzy Logic ontrol
Just like a Waterfall dropping from great heights, this feature creates tur ulence
inside the wash tu which results in etter dissolution of detergents within the
water helping it to spread evenly throughout the clothes. It also produces greater
movement of the wash load to give you enhanced cleaning action
Advanced technology features means that now your machine can do the thinking
for you. With the Fuzzy Logic Control, the machine will indicate the required
detergent level and will automatically decide the water level and wash time
needed ased on the load of the wash you put in and the temperature of the
water you choose.

Features
Features
-3-
Features
Features
Eject Mechanism
Tempered urved Glass Lid
Water Level Selection
Delay Start
hild Lock
The Sparkle range comes with a Curved Transparent Window for a clear view
of your clothes while they are being cared for. The Tempered Glass used is also
stronger and adds to the durability of your washing machine.
The Eject Mechanism allows you to open or close the door just at the press
of a utton. So now you can say good ye to handles!
The Memory Backup a ility in your machine means that if you are going out or
want to stop the cycle in the middle of a wash, you will e a le to restart it from
that particular point whenever you want.
With consumers desiring more water and energy saving washing machines, we
have a Water Level Selection feature which allows you to choose from a variety
of water levels depending on the wash load. This means there will e no more
wastage!
The Delay Start option will allow you to set the machine to start at a later time
or date so that your washing will e scheduled around your day and not your
day around your washing!
This is an important feature if you have children in the house. The Child Lock
option will disengage all the uttons on the machine so that your child is safe
from harm and the wash cycle cannot e tampered with.
Memory Back-up
epending on your laundry, create personalized cycles with your own preference
of wash, rinse and spin com inations as well as choose the desired water levels to
e in total control of your machine!
The Active Soak function is there for those stu orn stains that cannot e
removed with regular washing. It allows the clothes to e immersed in the
detergent infused water and sends quivers through the wash from time to
time so that it can attack the deepest dirt on your clothes and remove it.
ustomized Wash Program
Active Soak
D

Familiarisation with Control Panel
Familiarisation with Control Panel
-4-
The unit will indicate
the Remaining time to
complete the selected
program. Also indicates
the error signals whenever
they occur.
Power button is
used to switch ON
and switch OFF the
machine.
In Fuzzy program according
to the cloth load the Detergent
level will be shown on the
panel and Water level will
automatically get selected
Internally. In Custom mode you
can select the water level from
22Litres to 60Litres.
Note : If you select water levels
22, 30, 38, 46 and 54 the LEDs
will be blinking. For all other
water levels LEDs will continuously
on.
Display Unit
Display Unit
As you press this button
washing program changes
as follows.
Normal
Quick wash Water Saver
Jeans Sari Turbo Tub
Clean Baby care
Note : if you select Normal,
Heavy, Gentle, Quick wash
and water saver the LEDs will
be continuously ON. For all
other programmes LEDs will be
Blinking.
Heavy Gentle
Programs Selector
Programs Selector
To set the delay time
Press this button. The delay
time will change from 1 hr
to 20 hrs with each press of
the button with increment of
5 hr.
This button is used to start,
pause the operation. To change
the washing course during
operation, press this button to
pause and press the button to
restart the operation after
changing the course.
Delay Selector
Start/Pause Delay Selector
Start/Pause
Note : This machine is equipped with memory backup function. This helps to retain same program in case of power failure.
Water Level Selector
Water Level Selector
Power Button
Power Button
Child Lock
Child Lock
When the machine is ON, the default
mode is Fuzzy and Fuzzy LED will be ON.
If any program/water level is selected then
the mode comes out of fuzzy and Custom LED
will be ON and will execute the selected program.
If you press the mode button once then the
mode goes to custom where you can select the
wash, rinse and spin course as per your
requirement.
Once the course is completed, your selection
will be stored in the memory and the same can be
displayed during your next selection of custom
mode.
Note:
If you press the mode button twice
then machine goes to “Today only” mode
and both LED of mode button will be OFF
where you can select the wash, rinse
and spin as per your requirement. In this
case, selection is not stored in memory.
Mode
Mode
If any program is running
or after starting any
program the Water
Level Button & Program
Selection Button are
simultaneously pressed for
2 seconds, machine will
go into Child lock mode.
This feature inactivates the
control panel keypad.
Press the same buttons for
5 Seconds to de-activate
the Child lock.

Familiarisation with Control Panel
MOVING DISPLAY
MOVING DISPLAY
Familiarisation with Control Panel
-5-
With this button water inlet selection can be
changed to Warm and Hot from the default
Cold. For only baby care program the
default water inlet selection is Hot.
TUB :
Tub display When the Power is ON
till the completion of programe.
will be ON
CHILD LOCK :
Child lock display will be on when Child lock is activated
ERROR SIGNALS:
Error signal s will be ON if any error occurs. (No Drain, No water,
Imbalance and Lid open)
FUNCTION:
Soak, Wash, Rinse and Spin display will be ON as per the
Programme selected to show the current process.
PAUSE:
Pause display will be blinking when you pressed the
pause button.
DELAY:
Delay display will be ON when you pressed the
delay button.
TIME BAR:
Display of 1 bar shows the start of Programe & display of all
bars shows the completion of Program.
PULSATOR :
Pulsator display will be ON and Moving forward and
reverse to show you the real motion of the Pulsator inside
the machine during Wash and Rinse.
CLOTH :
Cloth display will be ON during Wash , Rinse and Spin.
ARROWS and WATER DROPS :
Arrows and water Drops will be ON during Spin to show you
the real Spin happening inside the machine.
Temp
Temp
If you want to select individual wash, rinse and spin
operation or combination of these three you can press these
buttons. During this course Mode will be Changed to “Custom”
from the default “Fuzzy”.
1. Wash can be selected from 6 min to 30 min in steps.
2. Rinse can be selected 1 time rinse to 2 times over
flow rinse in steps.
3. Spin can be selected from 1 min to 11 min in steps.
Note:
Incase there is combination of functions in Custom mode by
memory and,
1. If you want to select only Wash course then press Rinse
and Spin button till their LED gets OFF.
2. If you want to select only Rinse course then press Wash
and Spin button till their LED gets OFF.
3. If you want to select only Spin course then press Wash
and Rinse button till their LED gets OFF.
Same way you can get the combination of any two functions by
pressing other functions OFF.
Function Selector
Function Selector
WATER LEVEL:
Water Level indicator will be ON as per the water level
selected.
WATER :
Water display will be Blinking during intake of water.
DRAIN :
Drain display will be ON during draining of water.

-6-
Parts Location And Identification
Parts Location And Identification
MAGIC LINT FILTER BRUSH
CONTROL PANEL
DETERGENT DRAWER
PLASTIC BASE
SOUND ABSORPTION
PLATE
LEVEL ADJUSTMENT LEG
DRAIN HOSE
POWER PLUG
EJECTOR
TEMPERED CURVED
GLASS LID.

Installation & Preparation
Installation & Preparation
-7-
Install the washing machine
on a leveled and firm space.
Adjust washing machine
level by loosening or
tightening the leg adjuster
provided on the right hand
side of the bottom of the
washing machine.
See if the level on the washing
machine is correct.
Keep the
machine
more than
20 cm away
from the
walls to
prevent
noise.
Insert sound
absorption
plate into
the slot at
the Bottom
of the machine.
Horizontal tap
Extension tap
Square tap
Untighten the upper
connector screw and
the middle connector.
In case the diameter of
the tap is large remove
the guide plate
Connector
Fixing screw
Rubber
packing
Middle
Connector
Guide plate
Connector
Push the upper connector
up till the rubber packing is
in tight contact with the Tap.
Then tighten the 4 screws.
Turn the middle connector to
ensure no water leakage.
Inside rubber
packing
Connector
Middle
connector
Check to see if there is a rubber seal inside the connector.
Check the water hose to the inlet valve of the washing
machine, and then lock it by turning the hose connecting part.
To separate the water supply
hose from middle connector
shut off the tap. Then pull the
inlet hose down, pushing the
plate down.
Connect the water supply hose
to the middle connector, pushing
the plate up.
Pusher
Connect the Inlet Hose
Connect the Inlet Hose
Hose
Connector
Inside rubber
packing
Cold Water inlet
(Blue)
Hot Water inlet
(Orange)

Connecting the Drain Hose
Connecting the Drain Hose
-8-
Connect the drain hose to the outlet of the
washing machine.
Fix the drain hose with the clip, and then push
the clip toward the body of the washing machine
as shown below.
Additional hose is connected.
Place the drain hose over a threshold.
Never let the end of the drain hose be
immersed in water.
Less than 3m
Less than 2m
Less than
6 cm.

Preparation before Wash
Preparation before Wash
Check if laundry is
washable in water.
Be sure to remove things
such as keys, pins and
coins from the laundry.
Wash oily or dyed laundry
separately.
Shake loose dirt off
before washing.
Wash laundry with loose lint
by turning it inside out.
Wash delicate clothes,
wrapping them in a nylon
net.
READY?
Plug the power cord into
the electrical outlet.
Lay the drain hose on the
drain hole.
Connect the inlet
hose with the tap.
Drain hole.
-9-

Washing Procedure
Washing Procedure
Connect the inlet hose to
the tap. Plug in the power
cord. Lower the drain hose.
1
Put laundry in the tub.
3
Select the programme as you desired and
moment enjoy your time.
press the START/PAUSE button. From this
6
START/PAUSE
-10-
Press EJECT to release the
glass lid from the catch and
open it. Reverse the operation
to close the lid.
Note : If you pressed EJECT one time and
Lid is not lifted sufficiently from the catch
do not press it again instead lift it up.
2
Put proper amount of softener into the
Softener inlet if required. The Softener will be
automatically adds into the tub at the last rinsing cycle.
1. Do not add detergent or bleach into the softener inlet.
2. Using too much softener may lead unsatisfactory result.
Note :
4
Press the power switch.
5

Washing Procedure
Washing Procedure
-11-
POWER START/
PAUSE
Controller automatically displays the Detergent Level &
selects Water Level.
Press the power button to "ON"
Press the START/PAUSE button or wait for 10 seconds.
Close the lid.
Water level is selected & Detergent level is displayed
automatically
Put the detergent in the "Detergent Drawer” as per Display on
the Control Panel.
Soak, Wash, Rinse & Spin follow.
If you want to pause, press the START/PAUSE button
again. You can change the program when paused.
.
Use heavy program for washing heavy laundry.
Press the to "ON".
Press the button one time for Normal & Twice for
Heavy Program.
Press the button.
Close the lid.
POWER
PROGRAMS
Select the water level depending on the cloth load (default
"60 Ltr" level).
Put the detergent in the "Detergent Drawer”.
START/PAUSE
Soak, Wash, Rinse & Spin follow.
If you want to pause, press the START/PAUSE button
again. You can change the program when paused.
Use this program for washing Woolen or Delicate laundry.
Press the button to "ON".
Press the button three Times.
Press the button.
Machine runs for 1 minute to dissolve the detergent and stops.
Buzzer will beep and display will show "CL”.
Press the button.
Close the lid.
POWER
PROGRAMS
Fixed water level of "60 Ltr” is selected automatically.
Put the detergent in the "Detergent Drawer”.
START/PAUSE
START/PAUSE
Wash, Rinse & Spin follow.
If you want to pause, press the START/PAUSE button
again. You can change the program when paused.
LOAD THE LAUNDRY INTO THE MACHINE
Use this program for washing little dirty laundry within short time.
Press the button to "ON".
Press the button Four Times.
Press the button.
Close the lid.
POWER
PROGRAMS
Select the water level depending on the cloth load (default
"60 Ltr" Level)
Put the detergent in the "Detergent Drawer”.
START/PAUSE
Wash, Rinse & Spin follow.
If you want to pause, press the START/PAUSE button
again. You can change the program when paused.
QUICK WASH PROGRAM
Use this program for washing heavily soiled heavy laundry.
Note: Please do not use excess detergent.
Press the button to "ON".
Press the button Six Times.
Press the button.
Soak,
Close the lid.
POWER
PROGRAMS
Select the water level depending on the cloth load (default
"60 Ltr" Level)
Put the detergent in the "Detergent Drawer”.
START/PAUSE
Wash, Rinse & Spin follow.
If you want to pause, press the START/PAUSE button
again. You can change the program when paused.
JEANS PROGRAM
Use this program for washing Sari and similar kind of laundry.
Press the button to "ON".
Press the button seven Times.
Press the button.
Close the lid.
POWER
PROGRAMS
Select the water level depending on the cloth load (default
"60 Ltr” Level)
Put the detergent in the "Detergent Drawer”.
START/PAUSE
Wash, Rinse & Spin follow.
If you want to pause, press the START/PAUSE button
again. You can change the program when paused.
SARI PROGRAM
Use this program for washing Baby laundry & under garments.
Press the button to "ON".
Press the button Eight Times.
Press the button.
Soak,
Close the lid.
POWER
PROGRAMS
Select the water level depending on the cloth load (default
"60 Ltr" Level)
Put the detergent in the "Detergent Drawer”.
START/PAUSE
Wash, Rinse & Spin follow.
If you want to pause, press the START/PAUSE button
again. You can change the program when paused.
TURBO CLEAN PROGRAM
Use tub clean program for cleaning the machine and use Baby
care programme for cleaning Baby laundry.
Press the button to "ON".
Press the button Nine Times for Tub clean and
Ten times for Baby Care..
Press the button.
Close the lid.
POWER
PROGRAMS
Water level will be "26 Ltr” Level by default.
START/PAUSE
Wash & Spin follow.
If you want to pause, press the START/PAUSE button
again. You can change the program when paused.
TUB CLEAN / BABY CARE PROGRAM
FUZZY PROGRAM
NORMAL / HEAVY PROGRAM
GENTLE PROGRAM
POWER
PROGRAMS
POWER
PROGRAMS
POWER
PROGRAMS
POWER
PROGRAMS
POWER
PROGRAMS
POWER
PROGRAMS
Use this program to wash medium soiled clothes and to save water
and detergent using shower rinse technology.
Press the button to "ON".
Press the button five Times.
POWER
PROGRAMS
WATER SAVER PROGRAM
POWER
PROGRAMS
Select the water level depending on the cloth load (default
"60 Ltr” Level)
Put the detergent in the "Detergent Drawer”.
START/PAUSE
Soak, Wash, Rinse & Spin follow.
If you want to pause, press the START/PAUSE button
again. You can change the program when paused.
Press the button.
Close the lid.
POWER
PROGRAMS
START/
PAUSE
START/
PAUSE
START/
PAUSE
START/
PAUSE
START/
PAUSE
START/
PAUSE
START/
PAUSE
START/
PAUSE

CUSTOM
CUSTOM
Selectable Washing Methods
Selectable Washing Methods
-12-
WASH ONLY
POWER WASH
CUSTOM POWER SPIN
RINSE
WASH
POWER SPIN
RINSE
POWER
SPIN WASH
POWER SPIN
RINSE
WASH
CUSTOM POWER RINSE
Press the button to "ON".
Select your desired washing time by pressing WASH button.
Press the button once.
Washing goes on as per selection.
Close the lid.
POWER
START/PAUSE
PROGRAMS
SPIN ONLY
WASH AND RINSE
RINSE AND SPIN
WASH AND SPIN
WASH, RINSE AND SPIN
RINSE ONLY
Press the button to "ON".
Select your desired spinning time by pressing button.
Press the button once.
Spin goes on as per selection.
Close the lid.
POWER
SPIN
START/PAUSE
PROGRAMS
Press the button to "ON".
Select your desired washing timing and rinse by
pressing WASH & RINSE button.
Press the button once.
Wash and rinse go on as per selection.
Close the lid.
POWER
START/PAUSE
PROGRAMS
Press the button to "ON".
Select your desired rinse and spin timing by pressing
RINSE & SPIN button.
Press the button once.
Rinse and spin go on as per selection.
Close the lid.
POWER
START/PAUSE
PROGRAMS
Press the button to "ON".
Select your desired washing timing and spin timing by
pressing WASH and SPIN button.
Press the button once.
Wash and Spin go on as per selection
POWER
START/PAUSE
PROGRAMS
Close the lid.
Press the button to "ON".
Select your desired washing timing,
rinse and spin timing by pressing WASH,
RINSE & SPIN button.
Press the button once.
Wash, Rinse, Spin go on as per selection.
POWER
START/PAUSE
PROGRAMS
Close the lid.
Press the button to "ON".
Select your desired Rinsing program by pressing RINSE button.
Press the button to select the desired delay time.
Rinse
POWER
START/PAUSE
goes on as per selection.
Close the lid.
PROGRAMS
START/
PAUSE
START/
PAUSE
START/
PAUSE
START/
PAUSE
START/
PAUSE
START/
PAUSE
START/
PAUSE
POWER
CUSTOM
CUSTOM
CUSTOM

Maintenance
Maintenance
Plug out the power cord
from the outlet first.
1
Clean the filter in the inlet valve. Clean the filter when water supply into the tub is bad or the
inlet valve is clogged with impurity.
Pull out the filter from the
inlet valve with fingers.
2
Use a tooth brush to get rid
of filth and then insert the
filter back in position.
3
-13-
Clean the waste thread collected in the Magic Lint filter.
Clean the brush to get rid off residues and lints accumulated over the bristles.
Note :
1. Bristle distortion might be there in the brush a . This will be resumed
before next wash.
fter completion of wash cycle
2. If bristles are coming out of brush call Onida service person & replace with the new brush.
Push the upper
Push the upper
part of the filter
part of the Brush
and pull in.
Open the cover
as shown in
the figure.
Clean the filter.
Close the cover and insert the
lower part of the filter in the
Insert lower part of the Brush
basket first and then push the
in the basket first and then
filter with “click” sound.
push the
sound.
brush with “click”
1
1
23
4
3
Clean the Brush.
1
1
23
2
4
and pull in.
BRUSH
push the
sound.
brush with “click”

Trouble-Shooting
Trouble-Shooting
Check if the
tap is a open.
No water supply.
E1
Check for
water supply.
No drain.
E2
Is the drain hose
kept down?
Is the drain hose twisted?
or is not the threshold too
high?
If the tub is unbalanced the buzzer will sound and the
remaining time indication will show .E4
If there is any Pressure switch/Pressure switch hose connection
problem the buzzer will sound and the remaining time indication
will show .E5
No spining.
E4
E5
Is the lid closed properly.
Contact nearest service centre for rectification.
Is the laundry unevenly
balanced?
If the lid is opened during spin the buzzer will sound and
the remaining time indication will show .E3
E3
If the water does not drain within 5 minutes, a buzzer will
sound and remaining time indicator will show .E2
If the water is not supplied within 30 minutes, a buzzer will
sound and remaining time indicator will show .E1
-14-
No power
supply
Machine not
working.
The high level of
vibration and noise
during spinning.
Is the power switch
pressed?
Is the power cord
unplugged?
Power failure?
Fuse blown?
Has the START/PAUSE
button been pressed?
Is the water tap shut off?
Is the water level
normal?
Is the washing machine installed
on a level place?
Is the noiseproof plate properly fit
into the plastic base?
START/PAUSE
PROBLEMS CHECK-POINTS
PROBLEMS CHECK-POINTS

Guidelines for Safety and Durability
Guidelines for Safety and Durability
Observe the following guidelines for the durability of the washing machine and safety problems.
Do not expose the washing
machine to direct sun light
or rain.
Do not install the washing
machine around a damp place.
Do not sprinkle water over
control panel switches.
Do not plug many cords in
one outlet at the same time.
When plugging out the power
cord, do not hold the wire.
Have children stay away
from the washing machine.
Keep the washing machine
away from fire or heat source.
Do not pour caustic soda and
bleach over the washing
machine. It causes damage to
rubber parts.
Do not pour water with
temperature exceeding 70°C
into the tub.
Make sure of closing the lid,
particularly during spinning.
Do not put hands into the
rotating tub.
Let water drain away from
the drain hose thoroughly.
-15-
Note : When not in use, switch the power off from wall socket or remove the power cord. Machine
will give beeps till power supply is on. This is for safety.

Specifications
Specifications
(Design & Specification subject to change without notice)
-16-
DESCRIPTION SPARKLE 65X
CAPACITY (Kg) 6.5
TYPE Fully Automatic Machine
POWER SOURCE 230 V AC, 50 Hz
WATER PRESSURE RANGE (Kg/cm ) 0.3 to 8.0
WASHING SYSTEM Pulgitator
BRUSH Yes
WATER INLET 2 Nos. (Hot & Cold)
INNER TUB Stainless Steel - Hexo Drum
REVOLUTION SPEED Wash - 130 rpm
Spin - 740 rpm
MOTOR RATING 400 W (Input)
DRIER SYSTEM Spin Dry (Centrifugal Force)
WATER LEVEL 10 (Ten) Levels.
DIMENSION (WxHxD) (mm) 580x910x595
NETWEIGHT(Kg) 34.0Kg
ACCESSORIES
InletHose-2Nos.
Drain Hose - 1No.
Sound Absorption plate - 1 No.
2

OMAN : M/s Mohsin Haider Darwish, P.O.Box : 880, PC 112-RUWI, OMAN Tel :[phone] Fax :[phone]
44373876
KINGDOM OF SAUDI ARABIA:M/s Said Ahmed El-Ajou Trading Corp. LLC, Tel:[phone], Fax :[phone]
Overseas-Middle East Asia
UNITED ARAB EMIRATES : M/s Al Futtaim Electronics,DUBAI .U.A.E.Tel : [phone] Fax: [phone],
BAHRAIN: M/s Kewalram & Sons P. .PO Box : 84, Manama BAHRAIN Tel : [phone] Fax : [phone]
KUWAIT: M/s Sefeena Gen Trading & Cont Est, P.O Box :5610, Safat: 13057 KUWAIT Tel :[phone] fax : [phone]
QATAR: M/s Videohome & Electronics Centre,. PO Box : 4668,DOHA-QATAR,Tel : [phone] Fax : +974
+
State Service Number
Andhra Pradesh 040-39889000
Delhi 011-39889000
GOA 022-39889000
Gujarat 079-39889000
Haryana 0172-3988900
Karnataka 080-39889000
Kerala 0484-3988900
Madhya Pradesh 0731-3988900
Maharashtra 022-39889000
Punjab 0172-3988900
Rajesthan 0141-3988900
Tamilnadu 044-39889000
Uttar Pradesh 0522-3988900
W Bengal 033-39889000
Bihar 1800 30099000
Chattisgarh 1800 30099000
Himachal Pradesh 1800 30099000
Jharkhand 1800 30099000
Orrisa 1800 30099000
Uttaranchal 1800 30099000
Assam-Guwahati 0361-2413138 / 2413158
Assam-Jorhat 0376-2309008
Jammu & Kashmir- Jammu 0191-2562258
nos.
-17-