Onset Computer Corporation T-VER-8051-300 User manual

Veris Pulse Output kWh Transducer (Single CT) Connection Instructions
For use with HOBO®H22, U30 series data loggers and HOBO data nodes
© 2007–2010 Onset Computer Corporation. All rights reserved. Onset, HOBO, and HOBOware are registered trademarks of Onset Computer Corporation. Other
products and brand names may be trademarks or registered trademarks of their respective owners.
Manual Part No: MAN-VERIS-8051
Doc No: 11712-C
Applies to this Veris Pulse Output kWh Transducer:
Onset Part No. Configuration / VAC Output Veris Part No.
T-VER-8051-300 Single-phase 120-277 and
(balanced) 3-phase 480 Pulses representing kWh H8051-0300-2
DANGER!—HIGH VOLTAGE HAZARD
Installing transducer in an energized electrical enclosure or on any energized conductor can result in severe injury or death. This
transducer is for installation by qualified personnel only. To avoid electrical shock, do not perform any installation or servicing of this
transducer unless you are qualified to do so. Disconnect and lock-out all power sources during installation and servicing. Please
read transducer user’s manual for instructions and use.
This document provides instructions on connecting the Veris Pulse Output kWh
Transducer listed above to HOBO H22 and U30 series data loggers using a pulse input
adapter and to HOBO ZW series data nodes using an adapter cable. Note: For
information on connecting the transducer to the power source and other transducer
details, refer to the documentation provided by Veris.
Required:
•Veris Pulse Output kWh Transducer listed above
•HOBO H22 or U30 series data logger, or HOBO data node (ZW series)
•Pulse input adapter, Onset Part No. S-UCC-M006 (for H22 and U30 series)
•Adapter cable, Onset Part No. CABLE-2.5-STEREO (for ZW series)
•HOBOware®Pro software, version 2.2.1 or higher (2.4.0 or higher for U30
series; 3.0 or higher for ZW series)
Configuring the System:
See the following pages for the applicable connection diagram that corresponds to your electrical power configuration.
Data Interpretation:
The consumed energy in kilowatt-hours (kWh) per pulse is selected on the Veris transducer. The data recorded in the logger or
data node will be number of counts (pulses) per logging interval. For conversion to other units, the data must be exported from the
HOBOware Pro software. Note: For complete information on using HOBOware Pro, refer to the software documentation.
Veris Pulse Output kWh Transducer

Veris Pulse Output kWh Transducer (Single CT) Connection Instructions
Page 2 of 3
H22 and U30 Typical 120 or 240 VAC Single-Phase Three-Wire Connection
Pulse Output kWh Transducer
(fuse pack not shown)
HOBO H22 or U30 Series Data Logger
(H22-001 shown)
S-UCC-M006
Pulse Input Adapter
Connect to
Smart Sensor port
120
Black
Red
Yellow
120
Neutral
Yellow Voltage
Lead capped
Pulse-Rate Selection Switches and
Pulse Output Terminal Block (see details at below left)
*Note: Multiply output pulse count
by two for proper kWh indication.
White to (+)
Black to (-)
Pulse Output
Terminal Block Connection
1.00
123456
ON
0.50
0.25
0.10
Pulse-Rate
Selection Switch Settings
0.1 kWh/Pulse* 0.25 kWh/Pulse*
0.50 kWh/Pulse* 1 kWh/Pulse*
1.00
123456
ON
0.50
0.25
0.10
1.00
123456
ON
0.50
0.25
0.10
1.00
123456
ON
0.50
0.25
0.10
H22 and U30 Typical 277 VAC Single-Phase Two-Wire Connection
Black
Red
Yellow
277
Neutral
Yellow Voltage
Lead capped
Pulse Output kWh Transducer
(fuse pack not shown)
S-UCC-M006
Pulse Input Adapter
Pulse-Rate Selection Switches and
Pulse Output Terminal Block (see details at below left)
*Note: Multiply output pulse count
by two for proper kWh indication.
White to (+)
Black to (-)
Pulse Output
Terminal Block Connection
1.00
123456
ON
0.50
0.25
0.10
Pulse-Rate
Selection Switch Settings
0.1 kWh/Pulse* 0.25 kWh/Pulse*
0.50 kWh/Pulse* 1 kWh/Pulse*
1.00
123456
ON
0.50
0.25
0.10
1.00
123456
ON
0.50
0.25
0.10
1.00
123456
ON
0.50
0.25
0.10
HOBO H22 or U30 Series Data Logger
(H22-001 shown)
Connect to
Smart Sensor port

Veris Pulse Output kWh Transducer (Single CT) Connection Instructions
Page 3 of 3
H22 and U30 Typical 208 or 480 VAC Three-Phase Three/Four-Wire Connection
Pulse Output kWh Transducer
(fuse pack not shown)
S-UCC-M006
Pulse Input Adapter
Black
Red
Yellow
Phase
Phase
Pulse-Rate Selection Switches and
Pulse Output Terminal Block (see details at below left)
Phase
*Note: When using single CT model (T-VER-8051-300)
to monitor a balanced three-phase system, multiply
output pulse count by three for proper kWh indication.
White to (+)
Black to (-)
Pulse Output
Terminal Block Connection
1.00
123456
ON
0.50
0.25
0.10
Pulse-Rate
Selection Switch Settings
0.1 kWh/Pulse* 0.25 kWh/Pulse*
0.50 kWh/Pulse* 1 kWh/Pulse*
1.00
123456
ON
0.50
0.25
0.10
1.00
123456
ON
0.50
0.25
0.10
1.00
123456
ON
0.50
0.25
0.10
HOBO H22 or U30 Series Data Logger
(H22-001 shown)
Connect to
Smart Sensor port
Connect to pulse port
CABLE-2.5-STEREO
HOBO ZW Series Wireless Data Node
ZW Connection
(also refer to the appropriate CT wiring diagram in the H22/U30
connection section for your particular electrical power configuration)
Pulse Output kWh Transducer
(fuse pack not shown)
White to (+)
Black to (-)
Pulse Output
Terminal Block Connection
1.00
123456
ON
0.50
0.25
0.10
Pulse-Rate
Selection Switch Settings
0.1 kWh/Pulse*
0.50 kWh/Pulse* 1 kWh/Pulse*
1.00
123456
ON
0.50
0.25
0.10
1.00
123456
ON
0.50
0.25
0.10
1.00
123456
ON
0.50
0.25
0.10
0.25 kWh/Pulse*
* Refer to asterisked note in the H22/U30
connection section for your particular
electrical power configuration