ONWELL SM7-BT User manual

ONWELL Communication Limited. 20220905 – V1.0
User’s Manual – Wireless Speaker Mic 7
Model: SM7-BT
Wireless Speaker Mic. 7, Heavy Duty, Rechargeable
Battery Powered, IP55, 3.5mm earpiece port
FCC ID: 2A2BD-SM7-BT
Product Overview:
No.
Function
No.
Function
1
PTT
7
Status LED
2
Volume up
8
Function button
3
Volume down
9
Torch ON/OFF
4
Torch light LED
10
External earphone jack
5
Speaker / Microphone
11
Micro USB charging port
6
Power ON/OFF
12
Belt clip
Package contents:
Onwell GES-BTXM04, Bluetooth speaker microphone
USB chargeing cable
User’s Manual
Operation:
Power ON: Press power ON/OFFbutton ⑥, “Power on”
sound is heard and status LED⑦indicates purple, followed by
flashing blue.
Power OFF: Press power ON/OFF button ⑥, hold for 2
seconds until “Power off” sound is heard and status LED⑦
flashes purple once.
Function Button: When the device is paired with a phone,
Function button ⑧can be used as answer/end/reject calls,
answer waiting call, switching between the active calls, and
dial to the last called number.
Torch light LED: Power ON device, press torch ON/OFF
button ⑨for approx. 1 second to turn on torch light LED ④.
Press and hold for 2 seconds to turn off.
Volume control: Press volume up ②or down ③button to
adjust volume. The device will produce a tone when volume
reaches the minimum or maximum level.
External earphone: Open external earphone jack ⑩dust
cover, plug listen-only earphone with Ø3.5 2pole or 3pole
connector, loud speaker ⑤will automatically mute.
Status LED:
Status
LED Indicator
Power ON
Flashes Purple once, followed by flashing Blue
Charging
Constant Red
Charge complete
Constant Blue
Low battery
Flashes Red during power ON or after RX/TX, with
beeping tone every 5 min
Pairing mode
Flashes Red & Blue alternatively
Connection
Flashes Blue one every 5 seconds
Unpaired or lost link
Flashes Blue twice every 3 seconds
Paring Process for radio / phone
1. Make sure GES- BTXM04 is OFF, press & hold power button ⑥to
switch on GES-BTXM04.
2. GES-BTXM04 is under pairing mode when the LED ⑦flashes RED and
BLUE alternatively and “Pairing” sound is heard.
3. Start Bluetooth function on your radio / phone.
4. Find the device name “BT-XM04” under Bluetooth device list and
connect it.
5. Pairing process is completed.
General specification:
Speaker
Ø36mm 8Ω 1W 89±3dB @1KHz (0.5m 1W)
Microphone
-44±2dB@1KHz 0dB=1V/Pa
Protection grade
IP55 (dust cover properly closed)
PTT key life
≥1,000,000 Times
Talking Range
Bluetooth class 2, 10 meters
Battery
1500mAH Li-battery
Charging time
About 3 hours (5V 500mA)
Operation temp.
-20~50°C (-4~120°F)
Troubleshooting:
Does not power ON
Check if device is charged
Cannot charge
Check connections to the device and wall outlet.
Check if the device’s charging contacts are in contact
with optional desktop charging cradle.
Check charging status LED ⑦is on (RED)
Battery not holding
charge
Check if battery is fully charged.
Battery has definite service life; replace the battery
when it can’t give sufficient run time even when it’s
fully charged. Contact dealer to replace battery.
Pairing issue
Cannot find device, power off radio/phone for 5
second, restart and search again for device
RX / TX issue
Check Bluetooth connection and pairing.
Unclear speech
Check if water is trapped in grill, shake mildly to get
water out the speaker grill ⑤.
Battery charging

ONWELL Communication Limited. 20220905 – V1.0
Using Micro USB cable
Open dust cover and plug charger to Micro USB charging port⑪.
After 1 ~ 2 seconds, status LED ⑦indicates red while charging and
turns blue when fully charged. Please ensure the USB wall charger
adapter has output of minimum 1.0A. Close dust cover for
maximum water protection when not charging.
Using desktop charging dock
1. Single charging dock
A. Connect the AC/DC adapter to the jack on the back of
the charging dock.
B. Ensure the device is properly installed and makes proper
contact with the dock’s contacts.
C. Status LED ⑦of the device indicates red while charging
and turns blue when fully charged.
2. Multiple charging docks (Maximum 5 units)
A. Connect the charging docks laterally. DO NOT
connect more than 5 units.
B. Connect the AC/DC adapter to the jack on the back of
any charger dock.
C. Status LED ⑦of the device indicates red while
charging and turns blue when fully charged.
Maintenance and safety:
Tips to ensure usage safety, optimal performance with longer usage life
period.
Avoid drop, collision and piercing product.
Keep away from hazardous, corrosive chemical substances.
Keep away from heat, flame or high temperature
environment.
Keep away from extreme cold, to avoid components damages.
Close dust covers for earphone jack and charger jack when not
in use.
Store in dry and room temperature conditions.
Do not charge with unauthorized or damaged charger.
Charging with faulty charger may result in battery leakage, fire,
and bursting.
Do not charge the device with ambient temperature below
0°C (32°F) or above 45°C (113°F).
Do not disassemble the product, it voids warranty and
increases risk of water seal issue if product is not assembled
correctly. If battery requires to be replaced, please contact
your nearest service center for assistance.
If product is not used for a period of time, charge the product
every 2~4 weeks to keep battery well-conditioned.
For prolonged storage, recommend storage temperature is
25°C (77°F). Charge the battery every 60 days will avoid
battery getting deeply discharged and allow protection circuit
to activate.
Cleaning:
Before cleaning make sure product is powered OFF, unplugged
from charger and all dust covers properly closed.
If necessary, the external surface of the speaker microphone
may be cleaned with a mild soap solution and warm water.
Do not use chemical solutions such as stain removers, alcohol,
bleach or oil remover as this may damage or corrode product
surface.
Make sure water trapped inside speaker grill is shaken out
before usage.
ATTENTION
This device complies with part 15 of the FCC Rules and ISED Canada
license-exempt RSS standard(s). Operation is subject to the following 2
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that
may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. The device can be used in portable exposure
condition without restriction.
The product is too small to place complete label information, so the
label is placed on the packaging box.