Opentech ODT 4200PVR User manual

User’s
Manual
Personal Video Recorder
Free To Air Digital Terrestrial Receiver
ODT 4200PVR
OPENTECH INC.
6F, Dongwon Bldg., 275 Yangjae-Dong,
Seocho-Gu, Seoul, Korea 137-130
Tel : [phone]
Fax : [phone]
E-mail : [email protected]
OPENTECH MIDDLE EAST
RA 08 ZE07, Jebel Ali FZ,
P.O BOX 18033, Dubai, UAE
Tel : [phone]
Fax : [phone]
E-mail : [email protected]
OPENTECH Multimedia GmbH
Industriestr. 1 a
65760 Eschborn, Germany
Tel : + 49 (0) 6196 90 200
Fax : + 49 (0) 6196 90 2019 / 2029
E-mail : [email protected]
Open The Next Digital
Digital Terrestrial Receiver
120 / REV. 002

1.SAFETY PRECAUTIONS
2.GENERAL FEATURES
3.HOW TO CONNECT YOUR RECEIVER
4.HARDWARE DESCRIPTION
5.MENU OPERATION
6.HOW TO DO RECORD & PLAYBACK
7.HOW TO DO RESERVATION RECORD
8.TROUBLE SHOOTING
9.TECHNICAL SPECIFICATIONS
10. DIGITAL CHANNEL INFO
3
4
5
7
11
24
27
29
30
32
Table of Contents
Highest Tuning Speed!
Quick Channel Change!
Easy Installation & Operation
Table of Contents

GENERAL FEATURES 4
SAFETY PRECAUTIONS
3
This receiver has been manufactured to satisfy the international
safety standards.
Please read the following recommended safety precautions carefully
MAINS SUPPLY : 95�240V AC 50/60Hz
LOCATION : Locate the receiver indoor.
Locate receiver away from potential hazards such as houseplants, lighting, raining and direct sunlight.
OVERLOADING : Do not overload wall outlets, extension cords or adapters as this
can result in fire or electrical shock.
LIQUIDS : Keep liquids away from the receiver.
CLEANING : Before cleaning, disconnect the receiver from the wall socket.
Use a cloth lightly dampened with water (no solvents) to clean the exterior.
VENTILATION : Do not block the receiver ventilation holes. Ensure that free airflow is
maintained around the receiver.
Never set the receiver on soft furnishings or carpets. Do not use or store the receiver
where it is exposed to direct sunlight, or near heater.
Never stack other electronic equipment on top of the receiver.
Place the receiver at least 30mm from the wall.
ATTACHMENTS : Do not use any attachment that is not recommended by the manufacturer,
as it may cause a hazard or damage the equipment.
SERVICING : Do not attempt to service this product yourself. Any attempt to do so will
make the warranty invalid.Refer all servicing to a qualified service agent.
LIGHTNING : If the receiver is installed in an area subject to intense lighting activity,
protection devices for the receiver mains connector and modem telephone line are essential.
The individual manufacturer’s instruction for safeguarding other equipment, such as TV set,
Hi-Fi, etc., connected to the receiver, must also be followed during lighting storms.
- Fully MPEG-2 & DVB-T Compliant
- Input Frequency 174 ~ 862 MHz
- 2 Input Tuner with Loop Through IF Signal
- Supports DVB-T modulation schemes : QPSK, 16-QAM and 64-QAM
- Implements non-hierarchical and hierarchical 2K and 8K system operation
- Fast Booting & Auto Scan
- Quick Channel Changing Speed Less than 2Sec
- Max. 2000 Channels (TV & Radio) Programmable
- User Friendly 256 Colors OSD & Easy GUI
- A lot of OSD Language supported
- Supports EPG, PIG
- Radio Channel Background Display
- Favorite Channel List Programmable
- Master PIN Code Function & Parental Lock Function
- 20 Steps Volume Control
- Automatic NTSC / PAL Detection and Simple Video Converter (NTSC PAL)
- Window based S/W Download Program Supported by RS232 Serial Port
- Set to Set Download (Main Program, Channel Data)
- 4:3, 16:9 Letter Box & Teletext using OSD
- 7 Segment-4 Digit Display
- 5 Buttons on the Front Panel (Power On/Off, Channel Up/Down, Volume Up/Down)
- 2 SCART Output for TV & VCR
- 3 RCA Output for Video, Audio L/R
- Wide PLL RF Modulator (PAL B/G, I, D/K)
- S/PDIF Digital Audio
- Recording Capacity
- 40hours for 3.5Mbps Stream with 80GB HDD
- Time Shift Function With a Live Channel
- Fast Forward / Revers in Replaying
- 2Tuners : One Channel Watching + One Channel Recording
- Book Marking Function
- Delayed Recording in EPG
1. SAFETY PRECAUTIONS 2. GENERAL FEATURES

HOW TO CONNECT YOUR RECEIVER 6
HOW TO CONNECT YOUR RECEIVER
5
1) LOCATION OF THE RECEIVER
Your receiver should be placed under proper ventilation.
Don't put in completely enclosed cabinet that will restrict the flow of air, Resulting overheating.
The location should be safeguarded from direct sunlight, excess moisture, rough handling or
household pets
Avoid stacking other electronic components on the top of the receiver.
The location should be safely accessible by the cable from your antenna system.
2) CONNECTING THE RECEIVER WITH ANTENNA
Connect the coaxial cable to "ANTENNA.(A/B)" terminal marked at the rear of the receiver. All cable
connectors should be finger tightened, do not use any kind of wrench on the cable over connectors.
The cable should be 75‰ impedance coaxial twisted at the end with a ‘IEC’ type connector.
< Loop through >
In Automatic Channel Search Menu please set
connection type into Loop through if a link from
tuner A to B is made with a coaxial cable. This
mode will use all settings for tuner A also for
tuner B. Tuner A will be used for watching and
tuner B for recording onlySeparated.In
Automatic Channel Search Menu please set
connection type into Loop through if a link from
tuner A to B is made with a coaxial cable. This
mode will use all settings for tuner A also for tuner B. Tuner A will be used for watching and tuner B
for recording only
3. HOW TO CONNECT YOUR RECEIVER
Please DO NOT plug in the main power supply cord until you have
finished all the connections.
3) CONNECTING THE RECEIVER TO TV
To connect the receiver with your television, you can follow three methods :
through RF cable, and through SCART cable, S-Video Cable.
Connect the RF cable to the terminal marked "TV OUT" at the rear panel of the receiver and its other
end to the TV RF input socket.
In the case of connecting your TV through SCART cable, connect the SCART connector marked TV
to respective SCART port in the TV.
Connect the S-Video cable to the terminal marked ‘S-VIDEO’ at the rear panel of the receiver and its
other end to the TV or VCR S-VIDEO input socket.
4) CONNECTING YOUR VCR
To connect a VCR, the receiver has been provided with SCART at the rear marked ‘VCR'. Using a
SCART
connector, the VCR can be connected to the receiver.
5) CONNECTING EXTERNAL AUDIO HI-FI SYSTEM
To connect any external Audio Hi-Fi system, the receiver has been provided with two RCA
connectors at the back of the receiver, marked with Audio L and R respectively to connect the left and
Right Audio.
6) CONNECTING YOUR ANALOG RECEIVER
To facilitate the user using analog receiver to view analog channels, the receiver has been provided
with a loop through terminal marked as "IF OUT".
Connect the coaxial cable from this terminal to the IF input terminal of your analog receiver. Now by
keeping the receiver in standby, you will be able to tune and view analog channels
from your analog receiver.
ANT IN
TV
VCR S/PDIFS-VIDEO SERIAL PORT
R
L
TV OUT
ANTENNA
ANTENNA
(A/B)
ANTENNA
(A/B)
TV
ANTENNA
TV
ANTENNA
Loop Out
(A/B)
Loop Out
(A/B)
LOOP OUT
AC 100V-240V~
50Hz/60Hz
MAX.35W
VIDEO
AUDIO
TV
VCR Hi-Fi
Stereo Audio

HARDWARE DESCRIPTION 8
HARDWARE DESCRIPTION7
4.A. FRONT PANEL
1) ANTENNA (A/B)
: This port is to connect the coaxial cable. The IF input is provided through this port and
the input frequency range is 174 ~ 862Mhz.
2) LOOP OUT (A/B)
:
This is used to connect your digital receiver to your TV set so that you can
still Watch analogue programs. (2,7,9,10 & SBS)
3) SERIAL PORT
:
This port is used for software upgrades when connected to your computer
through a serial cable.(Not Supplied)
4) TV SCART : This is used to connect your TV via Scart leads.
5) VCR SCART : This is used to connect your VCR via Scart leads.
(When you connect external sets to above two SCART sockets, always use fully featured SCART
cables)
6) S/PDIF DIGITAL OUTPUT : This is for connecting digital optical audio to devices such as
surround sound amplifiers.
7) VIDEO, AUDIO R/L : These RCA connectors are used to connect the digital receiver to any
external device with RCA inputs. (TV set, Video, Projetor etc)
8) ANT IN : To be looped from TV OUT when connecting the digital receiver via RF to your TV.
9) TV OUT : Used to connect the digital receiver via RF to your TV.
10) POWER INPUT : This cable is to be Plugged into the AC mains power outlet.
The input AC volts range is 90V to 240V, 50Hz/60Hz supply.
11)S-VIDEO : Used to connect the receiver via S-VIDEO to Input such as TV Sets.
4.B. REAR PANEL
4. HARDWARE DESCRIPTION
ANT IN
TV
VCR S/PDIFS-VIDEO SERIAL PORT
R
L
TV OUT
ANTENNA
LOOP OUT
AC 100V-240V~
50Hz/60Hz
MAX.35W
VIDEO
AUDIO
1) POWER : This key is used to turn the receiver on and off (stand by).
2) CH : These keys are used to change the channels.
3) VOL : These keys are used to increase and decrease the volume
level manually.
4) INFRARED SENSOR : This is to receive the IR commands from the
RCU. Do not block the view of the sensor.
5) 7 SEGMENT DISPLAY : This SEGMENT display will show the current
channel number.While the receiver is in stand by mode, the display will show
the current time.
POWER
C H
VOL
INFRARED SENSOR
7 SEGMENT DISPLAY
6) LED DISPLAY: This LED display will show the current power mode status.
If receiver is in stand by mode,stand by mode LED will be on. and when
receiver is in on mode, on mode LED will be on.
(Option for LED display model only)
LED DISPLAY
STANDBY ON

HARDWARE DESCRIPTION 10
HARDWARE DESCRIPTION9
POWER : This is used to switch the receiver to ON/STANDBY mode.
MUTE : This key is used to toggle between normal and muted audio
0-9 NUMERIC KEYS : These keys are used to enter numeric values and to
select the channel directly by entering its number.
CH ▲▲CH▼▼: These keys are used to change channels and to browse the
menu.
VOL▶▶VOL◀◀: These keys are used to vary the volume level and to change
the cursor options in the menu.
MENU : This key is used to open up the menu.
EXIT : This key is used to exit from any menus.
OK : This key is used to enter and confirm any data to the receiver in the
menu systems. The Channel list can be accessed directly by pressing this
Key in the normal view mode.
Page Up : This key is used to page up the menu.
Page Down : This key is used to page down the menu.
GUIDE : This key is used to open up the Electronic Program Guide.
i: This key is used to view the channel information.
: This key is used to toggle between the TV channel and the radio channel.
LAST : This key is used to return to the previous channel.
AUDIO : This key is used to select the soundtrack list for the
current service and also used to select audio mode.
WIDE : This is used to change the screen mode , Auto, 16:9, 4:3, Letter Box
L/R : This is used to change the sound mode , LEFT , RIGHT ,STEREO
FAV : This key is used to switch between favorite lists.
TEXT : This key is for Teletext.
SLEEP : Sleep time.
Play : This is for Normal Speed play back.
Fast Forward : This is for Fast motion playback.
Fast Rewind : This is for Fast rewind motion playback.
Repeat : You can watch a certain defined section repeatedly.
Slow : This is for Slow motion playback.
Pause : This is for Pause the screen
Stop : This is for Stop recording or playback.
Jump Forward : You can move to 3 second forwarded pictures.
Jump Backward : You can move to 3 second backwarded picture.
Record : Start recording.
Recorded List & Function Key : Display recorded service list.
Time Shifting & Function Key : Start time shifting if time shifting is enabled.
Book Mark & Function Key : Add or delete bookmark.
Book Mark & Function Key : Go to the previous bookmark or switch
between favorite lists.
4.C REMOTE CONTROL UNIT
0~9
MENU
EXIT
OK
GUIDE
i
WIDE
L/R
FAV

MENU OPERATION 12
MENU OPERATION11
MAIN MENU
After installing your Antenna and receiver
with appropriate connectors, plug in the
AC main power and turn on the receiver.
Press the MENU key of the RCU. You will
see the Main Menu on the TV screen as
follows.
You can move into the desired submenu
using the up/down keys ( ) or
numeric keys. Press OK key to confirm
your selection.
If the Main Menu is locked, note that
you should enter the PIN code in order to move
into the corresponding submenu in case of Edit Channels menu, Edit Favorites menu
and Installation menu. The default factory PIN code is 0000 . Press the menu key or
exit key to return to previous menu.
1. EDIT CHANNELS
You can edit channels on various channel
lists - channel lock, delete channel, move
channel, edit the name of a channel, and
sort the channel list.
Select Edit Channels menu in main
menu, and you will be asked to enter your
PIN code. You can find the following Edit
Channels screen by entering it.
1.A. CHANNEL LOCK
Select the Channel Lock icon using the
left/right keys ( ).
Select the channel that you want to lock or unlock from the channel list using the up/down
keys ( ) and the page up/down keys ( ). Press the OK key to confirm your
selection. Also, you can use the“♬”key to select either TV channel list or Radio channel
list. Once the channel is locked, every time you try to watch the program, you will be asked
to enter PIN code. Press the menu key or exit key to return to previous menu.
1.B. DELETE CHANNEL
Select the Delete Channel icon using the left/right keys ( ).
Select the channel that you want to delete from the channel list using the up/down keys (
) and the page up/down keys ( ).
Press the OK key to confirm your selection.
Also, you can use the“♬”key to select either TV channel list or Radio channel list.
Press the menu key or exit key to return to previous menu.
1.C. MOVE CHANNEL
Select the Move Channel icon using the left/right ( ).
Select the channel that you want to move from the channel list using the up/down keys (
) and the page up/down keys ( ).
Press OK key to confirm your selection.
Move it to the position where you want to place it using the up/down keys ( ) and the
page up/down keys ( ).
Press the OK key to confirm.
Also, you can use the“♬”key to select either TV channel list or Radio channel list
Press the menu key or exit key to return to previous menu.
1.D. EDIT CHANNEL NAME
Select the Edit Channel Name icon using the left/right keys ( ).
Select the channel that you want to edit from the channel list using the up/down keys
() and the page up/down keys ( ). Also, you can use the“♬”key to select either
TV channel list or Radio channel list.
Press OK key to confirm your selection.
Select the character, which you want to edit using the browse keys ( ) and ( ).
Press OK key to confirm.
Save the name currently selected using the key.
5. MENU OPERATION
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
The main menu is classified into several sub menus, which will carry out the
various operations individually.

Personal Video Recorder Digital Satellite Receiver
MENU OPERATION 14
MENU OPERATION13
Press the menu key or exit key to return to previous menu.
1.E. SORT CHANNEL LIST
Select the Sort Channel List icon using the left/right keys ( ). Press OK key to
confirm.
Select the sort type which you want to sort using the up/down keys ( ). Press the
OK key to confirm.
Also, you can use the“♬”key to select either TV channel list or Radio channel list.
Press the menu key or exit key to return to previous menu.
2. EDIT FAVORITES
You can edit the favorite channel list,
such as add/delete a channel or move its
position, which facilitates you to easily
find your favorite channel from the
favorite channel list.
The favorite channel is classified into one
of 8 favorite categories depending on its
genre.
Select Edit Favorite menu in main
menu, and you will be asked to enter your
PIN code.
You can find the following Edit Favorite
screen by entering it.
2.A. ADD FAVORITE CHANNEL
You can choose TV channel list or Radio channel list in an alternative way by pressing the
“♬”key on the RCU.
By pressing FAV key on the RCU, you can choose your favorite channel group out of 8
favorite groups.
Select the Add Channel icon using the left/right keys ( ). Select a channel that you
want to add into the favorite channel list, using the up/down keys ( ) and the page
up/down keys ( ).
Press the OK key, and the selected channel will be added to the favorite channel list.
Press the menu key or exit key to return to previous menu.
2.B. DELETE FAVORITE CHANNEL
You can choose TV channel list or Radio channel list in an alternative way by pressing the
“♬”key on the RCU. By pressing FAV key on the RCU, you can choose your favorite
channel group out of 8 favorite groups.
Select the Delete Channel icon using the left/right keys ( ).
Select a channel that you want to delete from the favorite channel list using the up/down
keys ( ) and the page up/down keys ( ). Press the OK key, and the selected
channel will disappear from the favorite channel list. Press the menu key or exit key to
return to previous menu.
2.C. MOVE FAVORITE CHANNEL
You can choose TV channel list or Radio channel list in an alternative way by pressing the
“♬”key on the RCU. By pressing FAV key on the RCU, you can choose your favorite
channel group out of 8 favorite groups. Select the Move Channel icon using the left/right
keys ( ).
Select a channel that you want to move using the up/down keys ( ) and the page
up/down keys ( ). Press OK key to confirm your selection.
Move it to the position where you want to place it using the up/down keys ( ) and the
page up/down keys ( ). Press the OK key to confirm.
Press the menu key or exit key to return to previous menu.
2.D. RENAME FAVORITE GROUP
You can choose TV channel list or Radio channel list in an alternative way by pressing the
“♬”key on the RCU. By pressing FAV key on the RCU, you can choose your favorite
channel group out of 8 favorite groups. Select the Rename Favorite Group icon using the
left/right keys ( ).
Press the OK key and select the character, which you want to edit using the browse keys
(). Press the OK key to confirm.
Save the character currently renamed using the key.
Press the menu key or exit key to return to previous menu.
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲

MENU OPERATION 16
MENU OPERATION15
2.E. SORT CHANNEL LIST.
You can choose TV Channel list or Radio channel list in an alternative way by pressing the
“♬”key on the RCU. By pressing FAV key on the RCU, you can choose your favorite
channel group out of 8 favorite groups. Select the Sort Favorite List icon using the
left/right keys ( Press OK key to confirm. Select the sort type which you want to
sort using the up/down keys ( ). Press the OK key to confirm.
Press the menu key or exit key to return to previous menu.
3. INSTALLATION
Installation menu helps you to setup a
variety of parameters necessary for
receiving signal, add new service,
upgrade the new software and reset the
channel data.
Select Installation menu in main menu,
and you will be asked to enter your PIN
code.
You can find the following Installation
screen by entering it.
3.A. AUTOMATIC CHANNEL SEARCH
Your receiver includes the
preprogrammed information of
transponders. Select "Automatic Channel
Search" menu in "Installation" menu, and
the following screen will be displayed.
Select the desired transponder using the
left/right keys ( ).
Set Frequency Search option fields to the
appropriate value using the left/right
keys( ) or number key at each field.
Check the signal strength.
Press the "OK" key to start the "Automatic Channel Search" procedure. You can see the
progressive status of channel searching.
Please note that the "Automatic Channel Search" procedure may take a few minutes.
Press the "menu" key or "exit" key to return to previous menu.
3.B. MANUAL CHANNEL SEARCH
It will be more convenient to use Manual Channel Search procedure when you want to
search channel for a specified
transponder offered. As in Automatic
Channel Search , Manual Channel
Search also searches all channels
broadcasted over a specific transponder
using its predefined information. You can
add a new transponder if you cannot find
it on the predefined transponder list.
Select Manual Channel Search menu in
Installation menu, and the following
screen will be displayed.
3.B. 1 MANUAL CHANNEL SEARCH
Select the Search/Edit TP icon using the
up/down keys ( ).
Press OK key, and select the desired
transponder using the up/down keys
().
Press OK key to start the manual
searching for selected transponder. You
can see the progressive status of channel
searching.
If you cannot find the desired transponder

Personal Video Recorder Digital Satellite Receiver
MENU OPERATION 18
Personal Video Recorder Digital Satellite Receiver
MENU OPERATION17
from the transponder list, you can add it by inputting appropriate parameter values for a
new transponder using the ( ) key. When you want to change the parameter of an
existent transponder, select the parameter using the ( ) key, change its value and press
the Exit key. Correctly set various parameters.
3.D. PARENTAL CONTROL
This function prevents children or unauthorized persons from watching programs.
Also you can change PIN (Personal Identification Number) code. Select Parental Control
menu in Installation menu, and the
following screen will be displayed.
3.D.1. Receiver Lock
To lock receiver, select Receiver Lock in
the Parental Control menu and change it
to On mode using the left/right keys
()
3.D.2. Menu Lock
Select the maturity with left/right keys
()
3.D.3. Maturity Rate
To lock the Main Menu, select Menu Lock in the Parental Control menu and change it to
On mode using the left/right keys ( )
3.D.4. Change PIN Code
You can change your PIN code from
factory default value 0000 as follows:
Select Change PIN Code in the
Parental Control menu using the
up/down keys ( ).
Press OK key. Then you will be asked
for a new PIN code.
Once you enter a new PIN code,
the receiver will ask you to enter it in again.
After you enter a new PIN code twice, the PIN code is changed permanently.
If you forget the PIN code, you have to contact the distributor to find out it.
3.E. RECEIVER UPGRADE
You can upgrade the software of this receiver through serial port when the new software is
released.
Please contact the distributor for receiver upgrade.
Distributor supports you useful
information and new software for the
receiver.
3.F. TIME SETTING
You can adjust date and time in time
Setting menu. And, you can switch on/off
the STB using this menu.
Mode
Time adjust
Current date
Current time
On time
Off time
Information
Timeout
: Select manual or auto . In auto mode, the receiver is using the time code
from satellite signal.
: Difference between Greenwich time and local time (CET 1:00, summer-
time 2:00)
: The current date is indicated (manual mode only)
: The current time is indicated (manual mode only)
: To enter STB Turn — on time.
: To enter STB Turn — off time.
: To choose how long informations are shown on the screen

6. RECORD SERVICE
In this menu you can do reservation
record or record the current watching
channel.
(Refer 7. HOW TO DO RESERVATION
RECORD)
7. CHANNEL LIST
This menu helps you to easily select the
channel that you want to watch.
Press OK key , and the following screen
will be displayed.
You can get the information of channel number, channel name, and whether the program
is scrambled or locked.
To watch a specific channel, first select it by pressing the up/down keys ( ) and the
page up/down keys ( ). Then press OK key.
MENU OPERATION 20
MENU OPERATION19
3.G. FACTORY DEFAULT
This is to restore the factory set values in case the user has encountered some problems
after changing any new values of channel data and others, which may be in error.
Select Factory Default menu in Installation menu and press OK key.
If you want to continue, select Yes cell. The receiver will be reset to settings
automatically. Please note that the Factory Default procedure may take a few seconds.
3.H. HARD DISK
Time shifting : Time Shifting ON/OFF
Over Time : Overtime is a setting for the
record reservation. A record will be
extended by this setting. So often you
can permit that records are stopped to
early. Over time does not work if another
reservation would be influenced.
Hard disk format : Hard Disk Format
4. SYSTEM SETTINGS
This menu helps you to set up video
output mode, language, time, screen type
and parameters related with RF
modulator.
Select System Settings menu in main
menu, and the following screen will be
displayed.
Press the menu key or exit key to return to previous menu.
TV Select
RF Channel
RF Mode
Screen Type
Menu
Transparency
Menu Language
Audio Language
OSD Color
Inform. Timeout
Subtitle Auto
Mode
DOLBY DIGITAL
: Select video output mode CVBS or RGB
: Select or change RF channel number when your receiver is
connected to TV by RF connector. The factory preset value in
channel 38.
: in the above case, you can choose PAL B/G mode or PAL I mode or
PAL mode.
: You can choose either 4:3 or 16:9 according to the TV type.
: You can select the transparency of the menu.
: You can select the menu language
: You can select the audio language
: You can choose the OSD color
: You can choose how long information s are shown on the screen
: On mode, if a channel have subtitle after you change channel ,
subtitle is displayed automatically.
: On mode, if channel have AC-3 , AC-3 is chosen automatically.
▲
▲
▲
▲

Personal Video Recorder Digital Satellite Receiver
MENU OPERATION 22
MENU OPERATION21
Personal Video Recorder Digital Satellite Receiver
You can make a channel reservation in Channel Guide by pushing Remind Channel
button.
After you set up channel reservation, when the channel reserved is playing if you see other
channels, channel change automatically into remind channel.
9. RECORDED CHANNEL
This menu shows the recorded channels and the currently recording channel on the Hard
Disk. The file size and duration time are also shown.
Enter the recorded channel list by using the key. Select a the recorded channel using
Up/Down key and push the OK key. Playback starts. Push OK again to return to
normal picture. In the Recorded Channel list , you can set Lock/Unlock for the recorded
channels.
Also, you can rename and delete the recorded channels.
This enables you to move into that
specific channel. If you press OK again,
the menu disappears.
When you press the“♬”key, you can
alternatively select TV or radio channel
list. When you press key, you can see
all channel list or FTA channel or favorite
channel list.
Press the OK key, the menu key or
exit key to return to TV or previous
menu.
8. CHANNEL GUIDE
Press GUIDE key, and the following screen will be displayed.
It will give the titles of the current and next
programmes on different channels.
The information may include : current time
/ channel name, name of the current and
next programme, the start and total time
of the current programme, the start and
total time of the next programme.
Programme information will be available
only when it is included in the
transmission. With the i button you can get
more information about a marked event, if
available.
When you press the“♬”key, you can alternatively select TV or radio channel guide. In the
Channel Guide you can do reservation record for each event.
Press the GUIDE key, the menu key or exit key to return to TV or previous menu.
(* Refer “7. HOW TO DO RESERVATION RECORD”)
KEY : Set Lock/Unlock
KEY : Rename the recorded Channels.
KEY : Delete the recorded Channels.
* While Playback or recording, “Lock/Unlock”, “Edit channel name”, “Delete channel” are not
supported.
* If the recorded channel is a Radio Channel, Fast Forward, Fast Rewind, Slow Motion are not
support.

MENU OPERATION23
11. SLEEP Mode
Press Key. Please select off time
by pushing Key. You can select
reservation off time by
10,20,30,40,50,60 minutes
Personal Video Recorder Digital Satellite Receiver
HOW TO DO RECORD & PLAYBACK 24
1. RECORD
There are 3 Record ways, Quick Record , in the Channel Guide and in the Record
Service Menu.
a) Quick Record : Push key and the current watching Channel will be recorded. If you
want to stop the Record, push the key. If the Channel that you want to record has
EPG data it records the EPG s event.
b) Channel Guide : After moving to the event that you want to record in the Channel Guide,
push the key for the reservation record.
c) Record Service : If you move to Main Menu -> Record Service, you can input Date and
Time for the reservation Record.
*Please refer to: 8. HOW TO RESERVATION RECORD” if you want know how to record in the
Channel Guide & Record Service menu.
*In case the Reservation Record time is reached during recording a channel, it stops the recording
and asks if you want to start the reservation Record.
* A record will be extended by the over time setting. This often will permit that records are stopped
to early. Over time does not work if another reservation would be influenced.
<Tip> While you see another channel for recording, you push "PlayBack" key, then recording
channel is played
<NOTE> If a channel is High Definition channel , The channel cannot be recorded
2. PLAYBACK
1. If you push key, the Record Channels list appears.
2. Select the channel with which you want Playback using Up/Down key and OK key.
3. If you want escape Recorded Channel List please push Exit key or after selecting an
event OK .
* Please refer to the “6.9. RECORDED CHANNEL”
3. STATE INFORMATION
The State information shows Record channel name, State icon, Progress time, Recorded
time, Book Mark, Repeat status.
* You can see it pushing key in the Record & Playback menu.
4. BOOKMARK
Easily you can move and watch the point that you want again using Book Mark in the
Record & Playback menu.
6. HOW TO DO RECORD & PLAYBACK
L/R
10. AUDIO
Press key.
Select the audio mode which you want, using
the left/right keys ( ).
Some programs are broadcasted with one or
more alternative language soundtracks.
You can select the preferred audio language
for soundtrack using the up/down keys
().
You leave the menu with EXIT or
To quickly select the audio mode which do
you want, you can use hot key

1) Push key for set-up in the Record & Playback menu.
2) Using key, you can move to the Book Mark
you want.
* After moving to the Book Mark and pushing key
within 2 seconds, the set-up is cancelled.
5. REPEAT
Using Repeat, you can watch a certain defined
section repeatedly.
1) In Playback Menu, push key
2) Set the section using Volume Up/Down key.
3) Set repeat up pushing key
* For canceling Repeat, push key once more
6. FAST FORWARD
This is Fast motion playback. Please also see 10. Jump Forward
1) In Playback, push key.
2) In order to increase Playback Speed, push key several times.
3) For returning to Normal Speed, push key.
* Playback Speed can be increased by 4steps.
7. FAST REWIND
This is for Fast rewind motion playback. Please also see 11. Jump Backward
1) In Playback, push key.
2) In order to increase Rewind Playback Speed, push key several times.
3) For returning to Normal Speed, push key
* Rewind Playback Speed can be increased by 5 steps.
8. SLOW MOTION
This is for Slow motion playback.
1) In Playback, push key
2) For returning to Normal Speed, push key
9. PAUSE
Stopping the pictures, push key
HOW TO DO RECORD & PLAYBACK 25
Personal Video Recorder Digital Satellite Receiver
HOW TO DO RECORD & PLAYBACK 26
10. JUMP FORWARD
If you push while playback and recording or if you push key, you enter the Playback
menu. There you can jump fast forward using the key. You will see progress time and
recorded time.
11. JUMP BACKWARD
If you push while playback and recording or if you push key, you enter the Playback
menu. There you can jump fast backward using the key. You will see progress time
and recorded time.
12. TIME SHIFT
If you want to leave for while during watching a channel, Time Shifting function is very
useful function.
If you set up Time Shifting and return to you place, you can watch the channel from the
picture that was shown when you left.
1) During watching live channel, push key for Time Shifting set-up.
2) Pause the picture pushing key.
3) Push key for Playback.
4) If you want Slow motion playback, push key.
*If you return to Live channel, push key and cancel the Time Shifting function.
*You can use Time Shifting function after making Time Shifting ON in the “Main Menu”
Installation “Hard Disk” Menu.
*The Time Shifting channels are not recorded into Hard Disk. If you want to record something and
make “Time Shift”, you should push key and Jump Backward (see 11.) later. You can watch
the event from a selected point, while still recording.

HOW TO DO RESERVATION RECORD 28
HOW TO DO RESERVATION RECORD 27
There are 2 ways for Reservation Record. One is the way to set the date, time & duration of the
event you want to record in the “Record Service” menu. The other is the way to set program event
that you want to record in the “Channel Guide”.
For the reservation record, you must have synchronized the reservation’s time and your local
time, which is very important.
(Refer “5.SYSTEM SET-UP”) :
1. RESERVATION RECORD IN RECORD SERVICE MENU
In this menu you can do reservation
record or record the current watching
Channel.
Select Record Service in Main Menu.
Then select the channel that you want to
record using Channel (enter with OK
button). At Record you choose Current
record/Reservation record.
If you want to record the current channel,
choose the Current, select the duration,
change the File Name if you want, go to
Start and push OK .
In case of Reservation record, change the Mode and choose the reservation record time;
one time/every day / Weekly.
Using Date, Start Time, Duration set reserved date & time and push OK at Start
Key shows all the reserved program in the Reservation Table.
In the Reservation Table, you can delete
the reserved programs selectively or all of
them.
In case the date & time with which you
want do Reservation Record is doubled
with the registered date & time of
Reservation Table, it can t be registered
into the Reservation Table.
Also if every day, weekly is registered in
the Reservation table, the Reservation
Record and EPG Record for the same
time can t be registered.
7. HOW TO DO RESERVATION RECORD
2. RESERVATION RECORD IN CHANNEL GUIDE MENU
Press GUIDE key, and the following
screen will be displayed.
It will give the titles of the current and next
programmes on different channels, if
those information s are transmitted from
the provider.
In the Channel Guide you can do
reservation record for each event.
If you have an event to the reservation
record, you can do it pushing key after
moving to that event.
The reservation is canceled pushing key one more time.
If you want to see the reserved programs, push key and reservation table shows them.
Press the menu key or exit key to return to previous menu.
* In case you have two sametimes events only one can be recorded.
* When the event that you want to do reservation record is registered into the reservation table, you
can’t reserve it.
Channel
Record
Mode
Date
Start Time
Duration
File Name
Start &
Reservation
: Select the channel with OK key
: Select Current record/Reservation record.
: Select One time/Every day/Weekly (Only activated if you selected
Reservation Receord)
: Recording the Current channel, the Current date is shown. In the
Reservation mode, you can enter the date of reservation record.
: Recording the Current Channel, the Current time is shown. In the
Reservation mode, you can enter the time of reservation record.
: Enter the recording duration.
: Name the recording file. If you don t name it, the channel name
becomes the file name.
: If the Record type is Current , the recording is done from the current
time to the Duration time. When Record type is Reservation , it is
registered in the Reservation Table .

TECHNICAL SPECIFICATIONS
30
TROUBLE SHOOTING 29
Problem Solution
Does not display LED on
the front panel or the
receiver has no power
No pictures on the screen
No sound
Remote Control does not
operate
Poor picture quality
- Connect the power cord to the power outlet properly.
- Check if the receiver is in standby mode.
- Check if the video output port is firmly connected to the TV.
- Check if you have selected the correct channel or video
output on your TV
- Connect the audio cords properly.
- Check the volume level of the TV.
- Press key.
- Point remote control directly towards the receiver.
- Check and replace batteries.
- Check the signal strength in the Automatic Channel
Search menu. If this is low, try to adjust the channel
frequency
Searching Signal
- Connect the antenna cable properly..
- Check the signal strength in the Automatic Channel Search
menu.
About the Receiver
8. TROUBLE SHOOTING 9. TECHNICAL SPECIFICATIONS
On - Screen Error Messages
l. Tuner
Input Frequency
Input Level
Input Impedance
Connector Type
Channel Selection
IF Band Width
2. Demodulator
OFDM Spectrum
Modulation mode
Guard Interval Mode
Active symbol duration
FEC Decoder
3. Video Decoder
System Decoding
Profile and Level
Video Formats
Video System
RF Output
4. Audio Decoder
System Decoding
Audio Mode
Audio Control
5. Chip & Memory
CPU
Memory
UHF 470 ~ 862 MHz
VHF 174 ~ 230 MHz
-80 ~ -20 dBm
75ΩUnbalanced
`IEC' Type Female
PLL Synthesizer
UHF/ 8 MHz, VHF/ 7 MHz
2K and 8K Carrier Modes
non-hierarchical and hierarchical
QPSK, 16QAM, 64QAM
1/32, 1/16, 1/8, 1/4
Active symbol duration
1/2, 2/3, 3/4, 5/6, 7/8
MPEG-2 ISO/IEC 13818-2
MPEG-2 MP@ML
4:3(Normal) & 16:9(Widescreen)
PAL <-> NTSC Converter
CH. 21-69 (PAL B/G, I, D/K)
MPEG-1 Layer I & II (Musicam Audio)
Mono, Dual, Stereo, Joint Stereo, channel
20 Steps Level
32 Bit RISC CPU
2MB Flash Memory
8MSDRAM×2
2KB EEPROM

TECHNICAL SPECIFICATIONS
31
6. Demultiplexer
7. Serial Data Interface
Signal
Connector Type
8. Audio/Video Connectors
TV SCART
VCR SCART
Audio Output
Video Output
Digital Audio
S-Video
9. Hard Disk
HDD
10. Power Supply
Input Voltage
Type
Power Consumption
11. Physical Specification
Operating Temp
Net Weight
Dimensions
ISO/IEC 13818-1 Compliant
RS-232, 115200 bps
9 Pin D-Sub(male)
CVBS, RGB, Audio L/R
CVBS, Audio L/R
2 RCA Cinch (L/R)
1 RCA Cinch
1 S/PDIF
80GB, up to 120GB
Above 5400 RPM
AC 95 to 240V, 50/60Hz
SMPS
Max. 35W
+5°C to +40°C
About 3Kg
360(W)x245(D)x60(H)mm
AUSTRALIAN DIGITALCHANNEL LIST 32
10.AUSTRALIAN DIGITALCHANNEL LIST
Format: City name, Service name, channel number
WESTERN AUSTRALIA
Perth ABW SBS NEW STW TVW
12 29 11 8 6
Roleystone ABW SBS NEW STW TVW
56 53 65 62 59
Toodyay ABW SBS NEW STW TVW
56 53 65 62 59
NORTHERN TERRITORY
Batchelor ABD SBS QQQ NTD TND IMP
56 53 50 59 62 65
Darwin ABD SBS TND NTD
30 29 32 31
QUEENSLAND
Babinda ABNQ SBS TNQ STQ RTQ
42 52 46 43 49
Brisbane ABQ SBS BTQ QTQ TVQ
12 36 6 8 11
Cairns ABNQ SBS TNQ STQ RTQ
8 29 6 11 12
Cairns East ABNQ SBS TNQ STQ RTQ
42 52 46 43 49
Cairns North ABNQ SBS TNQ STQ RTQ
42 52 46 43 49
Currumbin ABQ SBS TVQ QTQ BTQ NRN NEN NBN
62 36 56 59 53 43 65 68
Darling Downs ABDQ SBS TNQ STQ RTQ
37 49 40 34 46
Gold Coast ABQ SBS TVQ BTQ QTQ NRN NEN NBN
62 36 56 53 59 43 65 68
Gordonvale ABRQ SBS RTQ STQ TNQ
42 52 49 43 46
Gympie ABQ SBS TNQ RTQ STQ
62 36 47 68 65
Gympie Town ABQ SBS TNQ RTQ STQ
62 36 47 68 65
Mackay ABMQ SBS RTQ STQ TNQ
10 29 35 9A 32

AUSTRALIAN DIGITALCHANNEL LIST 34
AUSTRALIAN DIGITALCHANNEL LIST
33
Nambour ABQ SBS TNQ RTQ STQ
62 36 47 68 65
Noosa/Tewantin ABQ SBS STQ TNQ RTQ
62 36 65 47 68
Rockhampton ABRQ SBS RTQ STQ TNQ
11 37 12 38 36
Southern Downs ABSQ SBS RTQ STQ TNQ
45 48 43 51 52
Sunshine Coast ABQ SBS QTQ STQ TNQ RTQ BTQ TVQ
62 36 59 65 47 68 53 56
Toowoomba ABDQ SBS RTQ STQ TNQ
55 67 64 58 61
Townsville ABTQ SBS RTQ STQ TNQ
31 37 41 38 36
Wide Bay ABWQ SBS RTQ STQ TNQ
9A 28 10 7 9
SOUTH AUSTRALIA
Adelaide ABS SBS NWS ADS SAS
12 33 8 11 6
Adelaide Foothills ABS SBS ADS NWS SAS
64 61 54 66 57
Elizabeth South ABS SBS ADS NWS SAS
64 61 54 66 57
Renmark/Loxton ABRS SBS RTS
39 40 35
South East ABGS SBS SES
39 40 32
Spencer Gulf North ABNS SBS GTS s38A
38 41 44 *
Victor Harbour ABS SBS ADS SAS NWS
56 53 65 59 62
*GTS has formally advised that it has elected to multi-channel its current and s.38A services on the
one digital channel (channel 44).
NEW SOUTH WALES
Armidale ABUN SBS NBN NEN NRN
32 29 38 35 41
Batemans Bay/ Moruya ABN SBS WIN CTC CBN
9A7 106358
Bega ABN SBS WIN CTC CBN
35 32 29 33 30
Bega/Cooma ABSN
50
Bombala ABSN SBS CBN CTC WIN
62 66 63 59 60
Bouddi ATN TCN TEN NBN NEN NRN ABHN SBS
61 62 65 68 59 56 37 34
Broken Hill ABLN SBS BKN s38A
10 12 9 *
Central Tablelands ABCN SBS CBN CTC WIN
36 42 37 43 40
Central Western Slopes ABQN SBS CBN CTC WIN
2 44414645
Coffs Harbour ABDN SBS NBN NEN NRN
61 68 67 56 64
Cooma Town ABSN SBS CBN CTC WIN
55 67 64 58 61
Cooma/Monaro ABSN SBS CBN CTC WIN
29 35 43 32 40
Dubbo ABQN SBS CBN CTC WIN
58 55 61 67 64
Eden SBS WIN CTC CBN
55 68 61 64 67
Gosford ABHN SBS ATN TCN TEN NBN NRN NEN
37 34 61 62 65 68 56 59
Grafton/Kempsey ABDN SBS NBN NEN NRN
Digital 36 39 33 30 38
Illawarra ABWN SBS WIN CTC CBN
51 54 36 37 38
Kings Cross ABN SBS ATN TCN TEN
30 34 48 33 45
Kotara ABHN SBS NBN NEN NRN
37 38 36 53 51
Manly/Mosman ABN SBS ATN TCN TEN
30 34 48 33 45
Manning River ABTN SBS NBN NEN NRN
7 9A 12 9 44
Merewether ABHN SBS NBN NEN NRN
37 38 36 53 51
Murrumbidgee Irrigation Area ABGN SBS AMN MTN
11 33 30 6
Murwillumbah ABRN SBS NBN NEN NRN
29 40 37 35 32
Narooma ABN SBS WIN CTC CBN
56 53 59 62 65
Newcastle ABHN SBS NBN NEN NRN
37 38 36 53 51

AUSTRALIAN DIGITALCHANNEL LIST 36
Nowra North ABWN SBS WIN CTC CBN
66 63 34 40 43
Richmond/Tweed ABRN SBS NBN NEN NRN
29 40 37 35 32
Stanwell Park ABWN SBS WIN CTC CBN
52 49 40 43 46
SW Slopes/E Riverina ABMN SBS CBN CTC WIN
46 48 47 51 50
Sydney ABN SBS ATN TCN TEN
12 34 6 8 11
Tamworth ABUN SBS NBN NEN NRN
54 51 60 57 63
Ulladulla ABWN SBS WIN CTC CBN
28 31 52 46 49
Upper Namoi ABUN SBS NBN NEN NRN
8 36 37 9A 40
Wagga Wagga ABN SBS CBN CTC WIN
55 54 58 64 61
Wollongong ABWN SBS CBN WIN CTC
51 54 38 36 37
Wyong ABHN SBS ATN TCN TEN NBN NEN NRN
37 38 61 62 65 68 59 56
AUSTRALIAN CAPITAL TERRITORY
Canberra ABC SBS CTC WIN CBN
9A 30 6 11 12
TuggeranongABC SBS CTC WIN CBN
59 57 62 65 68
Weston Creek/Woden ABC SBS CTC WIN CBN
59 57 62 65 68
VICTORIA
Ballarat ABRV SBS AMV BCV VTV
41 43 46 40 37
Bendigo ABEV SBS VTV AMV BCV
48 28 54 31 51
Ferntree Gully ABV SBS ATV GTV HSV
47 50 54 44 41
Goulburn Valley ABGV SBS AMV GLV VTV
37 36 45 42 9
Horsham ABWV SBS AMV BCV VTV
55 49 53 56 52
Latrobe Valley ABLV SBS AMV GLV VTV
42 30 33 39 36
Marysville ABV SBS ATV GTV HSV
60 57 54 51 63
Melbourne ABV SBS HSV GTV ATV
12 29 6 8 11
Mildura/Sunraysia ABMV SBS PTV STV
11 28 31 7
Murray Valley ABSV SBS AMV BCV TVT
58 59 62 65 60
Nhill ABWV STS AMV BCV TVT
66 67 61 64 63
Rosebud ABV STS ATV GTV HSV
60 57 54 51 63
Safety Beach ABV SBS ATV GTV HSV
60 57 54 51 63
Selby ABV SBS ATV GTV HSV
47 50 54 44 41
South Yarra ABV SBS ATV GTV HSV
60 57 54 51 63
Upper Murray ABAV SBS AMV GLV VTV
9A 7 12 8 10
Upwey ABV SBS ATV GTV HSV
47 50 54 44 41
Warburton ABV SBS ATV GTV HSV
60 57 54 51 63
Western Victoria ABWV SBS AMV BCV VTV
6 7 12 9A 10
TASMANIA
Hobart ABC SBS TVT TNT TasTV
8 9A 7 10 11
North East ABNT SBS TVT TNT TasTV
41 44 50 38 52
AUSTRALIAN DIGITALCHANNEL LIST
35