SIIG AV-GM07H3-S1 User manual

HDMI & Full 3D support over CAT5 Receiver
with IR Pass-through
P/N: AV-GM07H3-S1

~ 1 ~
Safety and Notice
The AV-GM07H3-S1 HDMI & Full 3D support over CAT5 Receiver with IR
Pass-through has been tested for conformance to safety regulations and
requirements, and has been certified for international use. However, like all electronic
equipments, the AV-GM07H3-S1 should be used with care. Please read and follow the
safety instructions to protect yourself from possible injury and to minimize the risk of
damage to the unit.
Follow all instructions and warnings marked on this unit.
Do not attempt to service this unit yourself, except where explained in this
manual.
Provide proper ventilation and air circulation and do not use near water.
Keep objects that might damage the device and assure that the placement of this
unit is on a stable surface.
Use only the power adapter and power cords and connection cables designed for
this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power
to the device before cleaning.

~ 2 ~
The AV-GM07H3-S1 HDMI & Full 3D support over CAT5 Receiver with IR
Pass-through provides the most ideal solution by which the high definition video and
high quality audio can be transmitted over a distance via Cat-5/5e/6 cable. The
AV-GM07H3-S1 can work with MA-5144/88KC matrix in the HDMI over CAT5 products
and allow you to extend HDMI compliant displays almost anywhere.
Features
Support HDMI Deep Color & 3D
HDCP compliant
Extends video signal up to 35m (115 feet) over CAT5e at 1080p and likely longer
with better HDMI source device, better grade HDMI display, and better quality
solid CAT6 cable
Supports 7.1 channel digital audio
Allows to control main matrix center through control line at remote receiver
Perfectly integrated with other HDMI over CAT5 series products
Wall mountable
The length depends on the characteristics and quality of the cables. Higher
resolutions and longer transmission distances require low skew cables (<25ns/100m)
for best performance. Unshielded CAT6 with metal RJ-45 connectors is
recommended.
Introduction

~ 3 ~
Specifications & Package Contents
Model Name
AV-GM07H3-S1
Technical
Role of usage
Receiver [RX]
HDMI compliance
HDMI Deep Color & full 3D
HDCP compliance
Yes
Video bandwidth
Single-link 225MHz [6.75Gpbs]
Video support
480i / 480p / 720p / 1080i / 1080p60
Audio support
Surround sound (up to 7.1ch) or stereo digital audio
HDMI over CAT5
transmission range
Full HD (1080p) –35m (115ft) [CAT5e] / 40m (130ft) [CAT6]
HD (720p/1080i) –50m (165ft) [CAT5e] / 55m (180ft) [CAT6]
HDMI equalization
8-level digital rotary control
Input TMDS signal
1.2 Volts [peak-to-peak]
Input DDC signal
5 Volts [peak-to-peak, TTL]
ESD protection
[1] Human body model —±19kV [air-gap discharge] & ±12kV [contact
discharge]
[2] Core chipset —±8kV
PCB stack-up
4-layer board [impendence control —differential 100Ω; single 50Ω]
Input
1x RJ-45 [HDMI signal] / 1x RJ-45 [Channel control] / 1x IR socket for IR
receiver
Output
1x HDMI
HDMI Input selection
Push-in button / IR remote control
HDMI source control
Controllable via IR pass-through from IR receiver at RX to IR blaster at TX
IR remote control
Electro-optical characteristics: = 25° / Carrier frequency: 20~60kHz
HDMI connector
Type A [19-pin female]
RJ-45 connector
WE/SS 8P8C with 2 LED indicators [TMDS & DDC channels]
3.5mm connector
Earphone jack for IR receiver
[IR RECEIVER] Receives IR commands from remote control
Mechanical
AV-GM07H3-S1
Enclosure
Metal case
Dimensions
(L x W x H)
Model
84 x 61 x 24mm [3.3" x 2.4" x 1"]
Package
168 x 112 x 42mm [6.6" x 4.4" x 1.7"]
Carton
585 x 242 x 565mm [1'11" x 10" x 1'10"]
Weight
Model
185g [6.5 oz]
Package
7000g [15.5 lbs]
Fixedness
Wall-mount with screws
Power supply
Not necessarily required*
Power consumption
1.5 Watt [max] (provided by MA-5188)
Operation
temperature
0~40°C [32~104°F]

~ 4 ~
Storage temperature
-20~60°C [-4~140°F]
Relative humidity
20~90% RH [no condensation]
PANEL DESCRIPTIONS
Front Panel
Rear Panel
1. INPUT SELECT: Push button for switching input source channel in sequential order
2. Signal Level 0-7: Adjust the 8-level equalization control to the received HDMI signals. The
HDMI signal level varies from 0 (strongest) to 7 (weakest) for respective transmission length
from longest possible range to short distance. Please adjust the signal level from 7 to 0 and
stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate
signal level setting may cause overpowering issue that would shorten the product life
significantly!
3. HDMI Output: Connect to HDTV with a HDMI cable
4. +5V DC: Spare power jack for over 60m transmission when the RX may need external
power to work*.
5. A/V SIGNAL: Plug in the CAT5 connected to the respective A/V SIGNAL port on the MA-5188
6. CHANNEL CONTROL: Plug in the CAT5 connected to the respective CHANNEL CONTROL
port on the MA-5188
7. IR RECEIVER: Plug in IR receiver
8. INPUT CHANNEL: Display the current showing HDMI source channel

~ 5 ~
IR PASS-THROUGH
IR Extenders
IR Blaster
IR Receiver
IR Sockets
MA-5188
IR Main: The default location for IR blaster to transmit all IR command signals received from
any of the four remote receivers to all of the HDMI sources.
IR PASS-THROUGH 1-8: IR blaster connected here can only transmit IR command signals from
the remote receivers that are setting at respective input channel from 1 to 8.
AV-GM07H3-S1
IR RECEIVER: IR receiver connected here can receive all IR command signals from the IR
remote controls of MA-5188 and all other HDMI source devices.
Definition of IR Earphone Jack
IR Blaster
IR Receiver
Incorrect placement of IR Blaster and Receiver may result in the failure of the IR
extenders. Please check carefully before plugging in the IR extender to the
respective IR sockets. Warranty will not cover the damage.
CAUTION!

~ 6 ~
CONNECTION DIAGRAM

~ 7 ~
NOTICE
1. When adjusting the signal level on the receiver unit, please dial the rotary control switch
from 7 to 0 and stop turning the rotary switch whenever the audio/video is playing
normally. Inappropriate signal level setting may cause overpowering issue that would
shorten the product life significantly!
2. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to
retrieve and provide DVI or HDMI display EDID information.
3. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e
125MHz UTP cable and ASTRODESIGN Video Signal Generator VG-859C & VG-870B.
4. The transmission length is largely affected by the type of Cat-5/5e/6 cables, the type of
HDMI sources, and the type of HDMI display. The testing result shows solid UTP cables
(usually in the form of 300m [1,000ft] bulk cables) can transmit a lot longer signals than
stranded UTP cables (usually in the form of fixed length patch cords). Shielded STP cables
are better suited than unshielded UTP cables. A solid UTP Cat-5e cable shows longer
transmission range than stranded STP Cat-6 cable. For long extension applications, solid
UTP/STP cables are the only viable choice.
5. EIA/TIA-568-B termination (T568B) for Cat-5/5e/6 cables is recommended for better
performance.
6. To reduce the interference among the unshielded twisted pairs of wires in Cat-5/5e/6 cable,
one can use shielded STP cables to improve EMI problems, which is worsen in long
transmission.
7. Because the quality of the CAT5/6 cables has the major effect on how long the
transmission limit can achieve and how good is the received picture quality, the actual
transmission range is subject to one’s choice of Cat-5/5e/6 cables. For desired resolutions
greater than 1080i or 1280x1024, a Cat-6 cable is recommended.
8. If your HDMI display has multiple HDMI inputs, it is found that the first HDMI input [HDMI
input #1] generally can produce better transmission performance among all HDMI inputs.
9. The AV-GM07H3-S1 has been tested extensively and found that it doesn’t require external
power supply. If in rare situation you find it cannot work with the MA-5188, please use any
+5V power adapter to plug in the power jack and see if it can work. If not, please contact
your technical support for further service.
10.Additional IR remote controls and IR blaster cables can be purchased as optional
accessories to control the HDMI sources located separately.
Performance Guide for HDMI over Category Cable Transmission
Performance rating
Type of category cable
Wiring
Shielding
CAT5
CAT5e
CAT6
Solid
Unshielded (UTP)



Shielded (STP)



Stranded
Unshielded (UTP)



Shielded (STP)



Termination
Please use EIA/TIA-568-B termination (T568B) at any
time

~ 8 ~
WARRANTY
The SELLER warrants the AV-GM07H3-S1 HDMI & Full 3D support over CAT5 Receiver with
IR Pass-through free from defects in the material and workmanship for 3 years from the date
of purchase from the SELLER or an authorized dealer. Should this product fail to be in good
working order within 3 years warranty period, The SELLER, at its option, repair or replace the
unit, provided that the unit has not been subjected to accident, disaster, abuse or any
unauthorized modifications including static discharge and power surge. This warranty is
offered by the SELLER for its BUYER with direct transaction only. This warranty is void if the
warranty seal on the metal housing is broken.
Unit that fails under conditions other than those covered will be repaired at the current
price of parts and labor in effect at the time of repair. Such repairs are warranted for 90 days
from the day of reshipment to the BUYER. If the unit is delivered by mail, customers agree to
insure the unit or assume the risk of loss or damage in transit. Under no circumstances will a
unit be accepted without a return authorization number.
The warranty is in lieu of all other warranties expressed or implied, including without
limitations, any other implied warranty or fitness or merchantability for any particular purpose,
all of which are expressly disclaimed.
Proof of sale may be required in order to claim warranty. Customers outside Taiwan are
responsible for shipping charges to and from the SELLER. Cables and power adapters are
limited to a 30 day warranty and must be free from any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be accurate.
However, The SELLER assumes no responsibility for any inaccuracies that may be contained in
this manual. The SELLER will NOT be liable for direct, indirect, incidental, special, or
consequential damages resulting from any defect or omission in this manual, even if advised
of the possibility of such damages. Also, the technical information contained herein regarding
the AV-GM07H3-S1 features and specifications is subject to change without further notice.
April, 2018
Support
For more info or tech support
http://www.siig.com/support