Oppo LT-1005DT User manual

TFT-LCD TV
READ CAREFULLY
BEFORE OPERATION
USER MANUALUSER MANUAL
LT-1005DT
WWW.OPPO.SEWWW.OPPO.SE

Before connecting theAC powercord to theDC adapter outlet,make sure the
voltage designation ofthe LCD TV corresponds tothe local electricalsupply .
If you are unsure of your power supply , ask your local power company .
Never insert anythingmetallic into thecabinet openings ofthe LCD TV;
otherwise may causethe danger ofelectric shock.
To avoid electric shock, never touch the inside of the LCD TV / adapter.
Only a qualifiedtechnician should openthe case ofthe LCD TV/adapter.
Never use your LCD TV/adapter when the power cord has been damaged .
Make sure thereis nothing restingon the powercord, and keepthe cord
away from places where people can trip over it .
Be sure tohold the plug,not the cord when disconnectingthe adapter from
an electric socket.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
TO PREVENT ELECTRICAL SHOCK.
DO NOT REMOVE THIS COVER. NO
USER- SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol indicates
dangerous voltage
inside the product that
presents a risk of electric
shock or personal injury.
This symbol indicates
important instructions
accompanying the
product.
Please read thismanual carefully beforeusing this product.
IMPORTANT SAFETY INSTRUCTIONS
Openings in the LCD TV/adapter cabinet are provided for ventilation.
To prevent overheating, these openings should not be blocked or covered.
Also, avoid usingthe LCD TV on abed ,sofa ,rug,or other soft surface. As
this, may block the ventilation openings in the bottom of the cabinet. If you
put the LCD TV in a bookcase or some other airless space, be sure to provide
adequate ventilation.
Do not exposethe LCD TV to extreme temperature conditions or to extreme
humidity conditions.
The apparatus shouldnot be exposedto dripping orsplashing and noobjects
filled with liquids,such as vases, should be placed on the apparatus.

Do not cleanthe front with keton-type materials(e.g.Acetone ),ethyl alcohol,
toluene, ethy lacid, methyl, or chloride-these may damage the panel.
Locate your DCadapter near an easily accessible AC outlet.
If your LCD TV does not operate normally in particular, if there are any
unusual sounds or smells coming from it, unplug it immediately and
contact an authorized dealer or service center.
High temperature cancause problems. Don t use your LCD TV in direct
sunlight, and keep it away from heaters, stoves, fireplaces, and other
sources of heat.
'
Unplug the DCadapter when it is going to be left unused for a long time .
Toreduce the risk of fire or electric shock,and annoying interference, use
the recommended accessories only.
If the LCD TV is broken, do not try to repair ityourself. Contact qualified service
personnel.
Unplug your DC adapter from the AC outlet before any service.
Be sure the service technician uses authorized replacement parts or their equi-
valents. Unauthorized partsmay cause fire, electrical shock, or other hazards.
Following any serviceor repair, be sure the service technician performs safety
checks to certify that your TFT-LCD TV is in asafe operating order.
The apparatus withCLASS I construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
IMPORTANT SAFETY INSTRUCTIONS

PANELBUTTON FUNCTIONS
Panel control
1
CONTENT
AV SETUP
AV setup
11
EXTERNAL EQUIPMENT
Connecting diagram
2
LET'S START
Change source operation
6
REMOTE CONTROL HANDSET
Remote buttons
3Battery installation
5
TV MENU SETUP
Picture
TV setting
System
7
8
910
Channel edit
DVD OPERATION
Brief introduction
14 Features
15
Compatible disc types
16
VCD, SVCD menuplayback
18 Select track toplay directly
by number buttons 19
Playback
17
Select language/audio
19 Repeat playback 20
Repeat playback of
selected segment
20 Fast playback 21
Play from thedesired position
21 JPEG file playing
22
CARD READERAND USB OPERATION
Usage of USBequipment
and 3-IN-1card reader
24
DISPLAY MODE
37
Display mode
SPECIFICATIONS
Specifications
36
DVD FUNCTION SETUP
General setup
26
28
Password setup
Preference setup
27
Video setup
27
Audio setup
26
TROUBLE SHOOTING
TV troubleshooting
34 DVD troubleshooting 35
DVB FUNCTION SETUP
General setup
29
DVB-T setup
30
Video setup
29
FM OPERATION
FM
12 System 13
32
Password setup
Teletext
33

1
PANEL BUTTON FUNCTIONS
PANEL CONTROL
Indicator( )Indicator is redwhen in standby mode, green when working normally.
1
IR sensor window
2
Front panel
Top panel
3STANDBY (Toswitch from standbymode to power-on mode)
4SOURCE (Select input source)
5CH-/+ (Increase or decreasechannel number/to moveselected menu item)
10 (Eject button)
6VOL-/+ (Increase or decrease volume/characteristics)
7SETUP (Enter or exit setup menu)
9
(Stop button)
8(Play/puase button)
345678910
1
11
12
13
14
15
16
17
19
20
Left panel
11 USB jack
12 MEDIA CARDsocket
13 12Volt DCpower input socket
14 AV audio video input jack
15 AV audio video output jack
17 Headphone jack
18 FM antenna input
Right panel
20 Disc in/out door
16 Headphone jack
18
RF input terminali
19
2

DVD or VCR player
NOTE
CONNECTING DIAGRAM
You should insert any interconnecting cables BEFORE plugging in the power cord.
EXTERNAL EQUIPMENT
The left of TV set
2
RL
VIDEO
RL
VIDEO
TV

3
REMOTE BUTTONS
REMOTE CONTROL HANDSET
STANDBY
1Switches between standbymode and power-on
mode.
VOLUME+/-
3
Increases or decreasessound amplitude
CHANNEL+/-
4
Steps up/down programnumbers.
RETURN
5
Toswap between aprevious program and the
current program (validin TV mode.)
SETUP
7
Display setup menu,different in different input
source.
B.L ON/OFF
8
Toturn on/off the screen (validin radio mode).
16 AUDIO
In DVB mode,to change sound track between left,
right and stereo.
PICTURE
2
Set picture mode:Dynamic, Soft, User, Standard.
1
2
3
5
8
11
7
10
6
17
4
9
14
9CARD/DISK
Toswitch in card reader, DVD and USB modes
(valid in DVDmode).
11 STOP
Tostop playing a DVD (valid in DVD mode).
10 DVD MENU
Display DVD menuor open/close PBC;
In DVB mode,long press toauto scan .
13
12
16
RATIO
6
Switch the picturemode in 4:3 or 16:9.
12
Switch between TV and radio modes (valid in
DVB mode).
TV/
17 ANGLE
Change camera angle(valid in
DVD mode)/CYAN button.
13 EPG/
Todisplay the program guide (valid in DVB mode)
/Toselect the previous chapter or track (valid in
DVD mode).
REPEAT
Torepeat playback (valid in DVD
mode)/ YELLOW button.
18
15
18
FAV./
In DVB mode,open favourite channel list/To select
the next chapteror track (valid in DVD mode).
14
ANT.ON/OFF
In DVB mode,turn on/off antenna power supply.
15

4
REMOTE CONTROL HANDSET (contd)
19 MUTE
Sound mute button.
EJECT
Disc in/out ,validin DVD mode.
20
TWO-DIGIT button
22
Switches between oneor two-digit program
numbers.
DISP
27
Display or hidechannel information /Display
or hide discinformation.
UP/DOWN cursor
26
Tonavigate upward/downward inthe menu.
SOURCE
23
Select input source:TV, DVD, AV, DVB, FM.
OK button
24
Toconfirm a selection/itemin menu.
LEFT/RIGHT cursor
25
Tomove left/right oradjust a selected item
in menu.
25
29
20
21
22
23
24
26
28
27
30
32
33
35
34
19
Number buttons
Toselect program number.
21
GOTO
34
Toplay a discfrom a certain time-point (valid
in DVD mode).
SUBT
32
In DVD/DVB modeselect the subtitlelanguage.
LANG
33
In DVD mode,to change sound decode mode like
DTS or Dolby. In DVB mode, switch the output
language.
31
INFO/
30
Todisplay the informationabout channel
and program (validin DVD andDVB mode)/
Fast forwards DVDplayback (valid inDVD
mode).
A-B
35
Torepeat play a disc segment (valid in DVD
mode).
28
Pauses playing/steps playbackin pause
mode (valid inDVD mode).
29
Toplay normally, valid inDVD mode.
31
Toenable or disable the function of teletext/ To
fast backward playback(valid in DVD mode).
TEXT/

5
BATTERYLIFE
NOTES
CAUTION
Please put batteryin a place children cannot access. If swallowed byaccident, please
contact your localdoctor immediately.
BATTERY INSTALLATION
REMOTE CONTROL HANDSET
When installing battery, please matchthe two polarities of the battery with the two polarities
inside the batterycase (positive upward,negative downward), as in the following figure:
12
Step 1: Push the button toward left. Step 2: Pull the battery holder out.
CR2025CR2025
Generally speaking, the battery can be used for oneyear. Butthe detailed battery life
and usage times are related to the remote controloperation.
If the remote control is still not operating whennear to theunit, please replace the battery.
Do not charge the battery, short-circuit, disassemble,heat or throwit into fire.
Take care notto fall andbeat the remote control, which will damage the remote control
or cause function trouble.
Please use CR2025 battery.
Do not userechargeable battery .
If the batteryof remote controlwill not be used for a long time, please take it out.
Please confirm whether the accessories contain the power adapter.
Please make sure to use power adapter within thespecification range, otherwiseit will
cause damage.
POWER SUPPLY
Step3: Insert one 3VOL LITHIUM BATTERY matching the -/+ polarities of the battery to
the -/+ marks inside the battery compartment, as in the diagram.
Use the car adapter in the accessories, connect oneend to thesocket in your car, the
other to the DC socket in the TV.
The input voltage of thecar adapter shouldbe 12Volts.

PICTURE
LET'S START
6
INDICATOR
STANDBY
After the unithas been suitably placed / fixed on the desk or your car, and allcords are
connected for power, input and output .
If your unitis not fixed with the battery pack, connect the adapter to theLCD TV, the unitwill
go into standbymode, and you can see the indicator turn red.
If your unitis fixed with the battery pack, and the quantity of electricity ishigh enough, the
unit will goto standby mode, the indicator will turn red. If not, please checkthe battery pack
or contact authorizedservice department.
CHANGE SOURCE OPERATION
You can change theinput source fromthe source menu. Press [SOURCE] button on unit or
[SOURCE] key onremote control toshow the menu on screen.
The current sourceitem is highlighted.Press [ ] buttons on the remote control, or [CH+/
CH-] key onthe top panelof LCD TV to selectyour desired mode.Press the [ ] or [OK]
button to confirmyour choice .
STANDBY
TV
DVD
AV
DVB
FM
What you shoulddo next is, press the STANDBY key on the toppanel of theTV, or [STANDBY]
button on theremote control to make the unit switch to power-on mode then youwill see the
LED indicator turngreen. Now you can enjoy the many features ofyour new product.