OPTI Kinetics OPTI User manual

1. Securely mount the OPTI Club Strobeflower heads,
using the hanging brackets, in desired positions. It
is recommended that a safety chain is also fitted.
2. Securely mount the Controller.
3. Link the Controller to the Head(s) using the two
1/4” stereo jack plugs, supplied with each unit,
linked with good quality stereo audio cable.
3a. For independent operation link each Head,
from one of the 4 CHANNELS on the
Controller, to CONTROL INPUT on
the Head.
3b. For identical operation link the first
Head to the Controller as above.
Then link that Head from CONTROL
THROUGH to CONTROL INPUT on
the next Head (as shown).
In this way a number of Heads can
be operated identically from each
CHANNEL, with each CHANNEL
operating independently.
Optikinetics Ltd.
38 Cromwell Road
Luton LU3 1DN England
Phone[phone]
Fax [phone]
e-mail [e-mail]
Website www.optikinetics.com
POWER RATING
Controller: 5 Watts maximum
Head: 100 Watts maximum.
MAINS CONNECTION
OPERATION
Operating Instructions
For optimum effect the OPTI Club Strobeflower Heads
should be used in conjunction with a 4 channel OPTI
Club Strobeflower Controller. Ask your dealer for a
demonstration.
FUSES
Controller: T0.5A (20mm x 5mmØ)
Head: F2A (20mm x 5mmØ)
OPERATING VOLTAGE
220-240V~ 50-60Hz
Both units come with a 2 metre, 3 core IEC lead with
5A fused UK mains plug. If another plug is required it
should be connected as follows:
BROWN = LIVE; BLUE = NEUTRAL;
GREEN/YELLOW = EARTH.
(220-240V~ Model)
Club Strobeflower
4. To switch on, connect the IEC leads to each unit
and the mains supply. Each Head will operate
according to the the Controller settings.
5. To disable (turn off) the Heads connected to the
Controller depress the BLACKOUT switch.
Beam Control
PARK The beam pattern is stationary.
RUN The beam pattern to rotates continuously
in one direction.
AUDIO The beam pattern to periodically changes
to the beat of the music at the audio input.
Sequencing of Lamps
PATTERN The lamps in the Heads on each of the 4
CHANNELS may be set to operate in four
preset sequences. The SPEED control
adjusts the rate of sequencing.
AUDIO The stepping of the PATTERN, from one
state to next, is initiated by audio signal.
OVERRIDE The lamp(s) of the corresponding channel
operates continuously with CHANNELS not
selected switched off.
Strobe Lamp Modes
SINGLE Each step in the sequence produces a
single flash. SPEED adjusts the flash rate.
BURST Each step in the sequence produces a
burst of flashes at maximum rate (16Hz).
SPEED adjusts the duration of each burst.
FULL The lamp(s) operate continuously.
The four ‘LED’ OUTPUT lights indicate that the lamps
are on, off or flashing.

Optikinetics Ltd.
38 Cromwell Road
Luton LU3 1DN England
Phone[phone]
Fax [phone]
e-mail [e-mail]
Website www.optikinetics.com
Operating Instructions (220-240V~ Model)
Club Strobeflower
AUDIO INPUT
For a really effective light show connect the AUDIO
INPUT on the Controller to the PA with 1/4” stereo jack
plugs and audio cable. Sequencing will operate in time
with the beat when the AUDIO switch is depressed.
REMOTE DISABLE INPUT
DISABLE INPUT allows the OPTI Club Strobeflower
System to be enabled or disabled by a lighting control
desk. The OPTI Strobeflower System can then be
integrated into a complete lighting installation.
The signal required by this input,via 1/4” stereo jack
plugs and audio cable, is as follows:
Disabled 0V Enabled +5 to +20V
Operation without a Controller
It is possible to operate the OPTI Club Strobeflower
system without the OPTI Club Strobeflower controller.
When mains supply is connected, without a controller,
each OPTI Club Strobeflower Head will operate inde-
pendently with the lamp in FULL mode and the beams
in RUN mode.
LAMP REPLACEMENT
Before attempting any maintenance read the safety
precautions sheet.
The only maintenance required is periodical cleaning of
the optical system to ensure effect does not degrade.
1. Remove the cover as detailed in Lamp
Replacement.
2. Using a non-abrasive glass cleaner compound and
a soft cloth, carefully clean the three elements of
the optical system. The lens at the front, the
dished reflector covered with mirrors and the small
mirror adjacent to the lamp.
Care must be taken to ensure that the lamp
remains scrupulously clean. Any marks, like
finger marks, should be removed using
methylated spirits and a soft cloth.
4. Replace the cover and secure using the reverse
procedure to removal.
After cleaning the optical system,it is advisable to
check the alignment of the lamp and adjust if necessary
(as detailed in Lamp Replacement).
Before attempting lamp replacement, read the safety
precaution sheet.
The lamp is available only from OPTI and their agents.
There is no suitable alternative.
The lamp replacement procedure is as follows:
1. Remove the screws on the sides of the Head.
2. Ease the side panels outwards slightly and lift the
cover clear of the unit. An earth wire connects the
chassis to the cover. This need not be removed.
MAINTENANCE
IMPORTANTWARNINGS
Allow the unit to cool for 30 minutes before touching.
Whilst the unit is open safety goggles must be worn.
The lamp has a high pressure gas filling, and if
broken, glass fragments will fly in all directions. The
lamp must not be touched by hand.
3. Remove the two screws which connect the lamp
wires to it's mounting blocks.Slacken the two
screws which secure the lamp, and remove.
4. Fit the new lamp in reverse procedure. The lamp
must be fitted the right way round. Adiagram is on
the rear panel of the Head illustrating this.
5. Replace the cover and secure in reverse procedure.
The optical system now needs to be adjusted to suit
the new lamp.
a) Connect mains power with Controller set to FULL.
b) Underneath the unit are two screws, labelled lamp
adjusters on the rear panel. Point the unit at a wall
several metres away. Adjust each screw alternately
until each beam produces a single circular spot.

Optikinetics Ltd.
38 Cromwell Road
Luton LU3 1DN England
Phone[phone]
Fax [phone]
e-mail [e-mail]
Website www.optikinetics.com
DMX CONNECTIONS
Connect the DMX ‘INPUT’ socket to a lighting desk or
controller‘OUTPUT’ socket using a 5 pin XLR lead.
Other DMX receivers or fixtures can then be connected
from the DMX THROUGH socket in a ‘daisy chain’.
The LED light is green when a DMX lead is connected
and receiving valid DMX. The LED is RED when there is
no DMX connection or there is no DMX signal.
DMX DIP SWITCHES
The first 9 DIP switches set the box’s start Address/
Channel to the same number as the slider on the DMX
Lighting Desk.
The start Address/Channel is calculated by adding1to
the sum of switch values. e.g.To set the Address to149
the switches turned ‘ON’will add up to148 (4+16+128) +
1= Channel149.
Instructions for OPTI Club Strobeflower with internal DMX
The last dip switch sets the DMX Channel to maxi-
mum output to test the appropriate unit.
DMX CONTROL
Two channels of DMX are used. The first controls the flash
rate and the second controls mirror rotation.
1st Channel
0The lamp is turned OFF.
1 - 62 Sliding scale for Flash Rate.
63 Lamp continuously ON.
The DMX values 0 to 255 are divided into 64 equal
divisions. The flash rate ranges from 0.25 to 13.5 per
second.
2nd Channel ( Start Channel +1 )
0 - 63 and 128 -191 MirrormotorOFF.
64 -127 and 192 - 255 Mirror motor ON.
To/From
DMX desk
DMX Channel
Dip Switches
To next
DMX unit
DMX Active
LED

SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using your OPTI Club Strobeflower System, basic safety precautions must be followed:
1. Read and understand all instructions before using.
2. Close supervision is necessary when any appliance is used near, but never by, children. Do not leave
appliance unattended while in use.
3. When mounted above head height a safety chain or cable must be fitted and secured to an
immovable object at all times.
4. Do not operate appliance with a damaged cord, or if the appliance has been dropped or damaged,
until examined by a qualified service person.
5. Always connect appliances to a grounded outlet.
6. Do not risk electric shock by immersing in water or allowing liquids to enter.
7. Do not operate too closely to a smoke generating machine or in an overly humid environment. Liquid
may condense inside the head unit creating risk of electric shock and may cause internal damage to
the unit.
8. Position the cord so that it will not be tripped over, pulled, or come into contact with hot surfaces.
9. If an extension cord is necessary,a cord with a current rating at least equal to that of the appliance
should be used. Cords rated for less amperage may overheat.
10. Under absolutely no circumstances must the OPTI Club Strobeflower Head or Controller case(s) be
opened when in operation.
11. To reduce the risk of electric shock, do not dismantle this appliance. Always take it to qualified
repairers when servicing is required.
12. The procedures described in the Maintenance section must be carried out by qualified service
personnel working under the authority of the manufacturers recognised agent.
13. Always unplug appliance from electrical outlet before maintenance, cleaning, lamp changing and when
not in use. Grasp plug and pull to disconnect. Never yank cord.
14. DO NOT attempt lamp replacement, or any other maintenance, while the unit is still hot as there is a
risk of burns from the lamp. Care must also be taken,as burns can occur from touching other hot
parts. Allow to cool for 30 minutes.
15. After any maintenance or cleaning all parts must be absolutely dry before refitting.
16. When replacing the cover(s) always ensure that all wiring is correctly engaged.
17. Let appliances cool completely before packing.
WARNINGS
Direct viewing of the lamp at close range can result in eye damage and must be avoided.
Strobe lights must never be used in the presence of epileptics.
Optikinetics Ltd.
38 Cromwell Road
Luton LU3 1DN England
Phone[phone]
Fax [phone]
e-mail [e-mail]
Website www.optikinetics.com
Club Strobeflower