Orava RM-206 User manual

1EN
RM-206
Instruction manual
Kitchen mixer with glass container
EN
RM-206

2EN
The intended use of the device
The device is intended exclusively for the mixing of liquid, soft and semi-
hard foods (frozen fruits and vegetables) and/or for the mixing of frozen
foods and ice crushing an /or for chopping nuts, spices, etc. in containers
for preparation, is determined by the technical and operating parameters
and features of the equipment, the safety and user instructions and the
external influences of the operating environment.
ORAVA electrical appliances are manufactured according to the state of
the art and recognized safety-technical rules. Nevertheless, the use or use
contrary to designation may result in the risk of injury or endanger the life of
the user or third person, damage to the device and other material values.
1. GENERAL SAFETY INSTRUCTIONS AND WARNINGS
• This document contains important safety instructions and warnings for
safe, correct and economical operation of the electrical equipment. Its
compliance helps the user avoid risks, increase reliability and product life.
• In this document, the generic term product is used in text parts such as:
electrical equipment - any device used for the production, conversion,
transmission, distribution or use of electricity.
• From the point of view of the purpose of using electricity, the concept of
electrical equipment in the strict sense of the word will include the following
categories:
- household electric appliances,
- information and communication equipment,
- consumer electronics,
- lighting equipment,
- electrical and electronic tools,
- toys and equipment for sporting and recreational
1.1 General safety instructions
• Before commissioning the unit, we recommend that you carefully read
the operating instructions and operate the equipment in accordance with
the instructions!
• The safety instructions and warnings in this manual do not cover all the
possible conditions and situations that may arise when using the device.
The user must understand that a factor that can not be incorporated
into any of the products is responsibility and caution. These factors must
therefore be ensured by users / users who use and operate this device.
• Failure to follow the safety instructions and warnings is forbidden by the
manufacturer for any damage to health or property!
• Make sure that the appliance is complete and shows no signs of damage
before using the appliance for the first time. If the product is defective or if it
has any visible damage, do not use the product.
• Keep the operating instructions as close to the device as possible
throughout its service life. Always keep the operating instructions together
with the appliance for future use and use by new users.

3EN
• Use the appliance only for the purpose for which it is intended and in the
manner specified by the manufacturer.
• The appliance is intended for home and similar indoor use, with no special
focus.
• It is not a professional device for commercial use.
• Do not change the technical parameters and features of the device by
unauthorized modification or modification of any part of the device.
• The manufacturer is not responsible for damages caused during
transportation, misuse, damage or destruction of the equipment due to
adverse weather conditions.
1.2 Safety of the operating environment
• Do not use the device in an industrial environment or outside environment.
• Always keep the operating environment clean and well lit.
• Do not place the device on an unstable surface. Overriding or dropping the
device may result in personal injury or damage to the device.
• Do not expose the unit to direct sunlight or excessive heat sources.
• Do not use an electric appliance in areas with flammable liquids, gases or
dust. The appliance may be the source of scaling, which can result in the
ignition of dust or vapors.
Features of the operating environment
1. Ambient temperature: +5 ÷ +40 ° C
2. Humidity: 5 ÷ 85%
3. Altitude: ≤ 2 000 m
4. Occurrence of water: intermittent condensation of water or occurrence of
water vapor
5. Occurrence of foreign bodies: amount and type of dust are not significant
Protection class: IP20
• Other characteristics of the operating environment (mechanical stress
- shocks and vibrations, occurrence of plant, animals, weather effects)
are negligible in terms of effect on the correct and safe use of electrical
equipment.
1.3 Electrical safety
• Before connecting the appliance to the power supply for the first time, make
sure that the voltage on the appliance label corresponds to that of the
household electrical outlet.
• The electrical appliance is designed for mains supply 230 V ~.
The electrical safety of the appliance is guaranteed only if it is properly
connected to the electricity grid.
• Only use a power cord with a plug (mains lead) that came with the device
and compatible with a wall outlet. Using another cable may result in fire or
electric shock.
• Always connect an electrical appliance to an easily accessible power outlet.
In the event of an operating fault, the appliance must be switched off as
soon as possible and disconnected from mains supply.

4EN
• Do not pull the power cord / power cord by pulling on the cord / cord.
Disconnect the power cord by pulling the plug behind the power cord /
power cord plug.
• If you use an extension cord, check that the total rated (ampere) power of
all devices connected to the extension cord does not exceed the maximum
current rating of the extension cable.
• If you need to use an extension cord or power supply block, make sure that
the extension cord or power pack is plugged into a power outlet, and not
to another extension cord or power supply. Extension power cord or power
supply block must be designed for grounded plugs and plugged into a
grounded outlet.
• The power plug of the appliance must be compatible with the mains socket.
Never use any adapters or modify the socket in any other way. Do not use
inappropriate or damaged soclets.
• To avoid electrical shock, plug the power cables into properly grounded
electrical outlets. If the device is equipped with a 3-pin power supply cord,
do not use adapters that do not have a grounding element or remove the
grounding element from the plug or adapter.
• Do not bend, crush or otherwise expose the power cord / power cord of the
appliance to mechanical stress or external heat sources. Damage to the
power cord may result in electric shock.
• If the power cord is damaged, disconnect the appliance from the mains and
do not use it again. If the power cord / power cord is damaged, it must be
replaced by the manufacturer, its service department, or a qualified person
to avoid the risk of electric shock.
• Regularly check and maintain the electrical appliance as well as the
power cable. Disconnect the power plug regularly and clean it if necessary.
Pollution by dust or other substances may cause disruption of the insulating
state and consequently fire.
• Do not expose the appliance to water or moisture. The ingress of water into
the appliance increases the risk of electric shock. If the power cord is wet
or the appliance gets water, disconnect it immediately from the mains. If the
appliance is plugged into a mains socket and if possible, turn off the power
supply before attempting to disconnect the power supply. If you are pulling
wet wires from a live power source, be very careful.
• If the electrical equipment is installed (connecting) the protective covers are
dismantled, the electrical parts must not be accessible to the user when the
installation is finished.

5EN
1.4 Safety of persons
• This appliance is intended for use by persons without an electrotechnical
qualification (layperson) according to the instructions specified by the
manufacturer.
• Device operation includes activities such as switching on and off, user
manipulation and setting of operating parameters, visual or auditory
inspection of the equipment, and user cleaning and maintenance.
• This appliance can be used by children 8 years of age and older and
persons with reduced physical, sensory or mental abilities or lack of
experience and knowledge only when under the supervision or guidance of
the responsible person have been instructed to use the appliance in a safe
way and understand the potential hazards .
• Cleaning and user maintenance can be carried out by children 8 years of
age and older only under the supervision of the responsible person.
• Children may not play with the appliance.
• Always keep the appliance out of reach of children during use and
operation. Be sure to download the appliance even for a freely accessible
power cord.
• Always be careful when operating the electric appliance. Do not use an
electric appliance if you are overly tired, under the influence of medication
or narcotic drugs that reduce attention and focus. Inattention during
operation may result in serious injury.
1.5 Cleaning, maintenance and repairs
• Observe the normal user cleaning and maintenance of the appliance in
the recommended way. Do not use solvents or harsh cleaners for cleaning.
Pollution and visible stains from finger contact, respectively. The hands
can be cleaned using detergent detergents specially designed to clean
household appliances.
• If you do not use the appliance, clean it or disconnect the appliance from
the power supply when the appliance is faulty.
• Do not disassemble the appliance. The appliance works with a dangerous
voltage. For this reason, always switch off the appliance and disconnect
it from the power supply. In the event of a fault, please have the repair
serviced by an authorized service center.
• Only guarantee qualified and qualified personnel to repair and repair the
electrical appliance.
(*) Appropriate qualified professional: the sales department of the manufacturer or importer or the person
qualified and authorized to carry out this type of activity with the ability to avoid all risks.

6EN
2. Special Safety Instructions.
Read carefully!
• Electrical equipment is designed and manufactured in such a way that
ensure safe operation and use by persons without professional
qualifications. Despite all the measures taken by the manufacturer to
ensure safe use, handling and use, it carries with it some residual risks and
associated potential hazards.
• The following symbols and their meanings have been used on the device
and in the accompanying documentation to warn of possible hazards:
This symbol alerts users that the device is operating a dangerous
electrical voltage. Do not remove protective covers on the device.
Failure to observe the safety instructions during use and
operation of the device may result in:
Danger of electric shock! Danger of serious injury or life
threatening!
This symbol alerts users that the following precautions can be
avoided if the following precautions are observed when operating
and operating the device:
Danger of serious injury or life threatening!
Danger of damage to equipment or other damage to property!
This symbol alerts users that the following precautions can be
avoided if the following precautions are observed when operating
and operating the device:
Danger of tearing or puncture of your fingers!
This symbol means that the product is made with a double
insulation between hazardous live parts (parts with dangerous
voltage from the mains) and parts that are accessible in normal
use.
Transportation / Transfer
• When transporting and using, for example, of the transport cart, be careful
when moving, to avoid overturning the device.
Only transport/transmit the device after thorough inspection of the space
and routes, which must be unobstructed.
Never transfer the device while in operation. Do not carry the device while it
is plugged into a wall outlet.
Warning!
• Some surfaces may become warm when operating the machine. Do not
touch hot surfaces! Never transfer the appliance until it has cooled down to
ambient temperature.
• Transfer the device firmly by both hands to the bottom edge of the base or
fixed parts of the body.
• Make sure that your hands and equipment are not damp or slippery when
carrying.

7EN
• Only persons who are competent and sufficiently physically fit to carry
the device (in view of the size and weight of the device) can only be
transported.
There is a risk of serious injury or life threatening!
There is a risk of damage to the device!
Expand/Packaging
• Unpack the equipment and accessories before putting it into service and
remove all parts of packaging material and labels. Store the packaging in
a safe place, especially out of the reach of children and unaccompanied
persons, or dispose of them safely.
There is a risk of serious injury!
Risk of suffocation!
Check/ Startup
• The appliance is designed for food preparation. Therefore, thoroughly clean
all parts of the appliance before commissioning it, following the instructions
in the „Commissioning“ section. „Cleaning and maintenance“.
• Never clean the appliance (its drive unit with electrical parts and controls)
and the power cord with the plug in a way (under running water) that could
cause the liquid to flow into the device.
• Clean these parts with a damp cloth only and wipe dry or let it dry.
• Only clean the appliance if it is switched off and disconnected from the
mains.
• We recommend performing both initial and subsequent regular machine
inspections.
• Never use the appliance if it is incomplete, damaged or damaged in any
way during transportation or use.Do not use non-original and incomplete
parts of the device and its accessories.
There is a risk of serious injury!
There is a risk of electric shock!
Location/Installation
• Only place the appliance on straight, firm and stable pads - kitchen work
desks and furniture parts, suitable for the location of kitchen utensils.
• Always make sure that the place you want to place the device has enough
space, mechanical strength and appropriate lighting.
Warning!
• Do not expose the device to:
- direct sunlight, sources and equipment producing heat,
- vibration and mechanical stress,
- excessive dust,
- water and excess moisture,
- insect,
- an aggressive external environment.

8EN
• Do not use or dispose of the appliance:
- to unstable tables or parts of furniture,
- on an uneven and dirty surface,
- on the sealing edge of tables or parts of furniture,
- in the vicinity of containers with water or other liquids.
• Do not cover the appliance in part. Do not place any objects on the device.
Do not insert or allow the foreign bodies to enter the holes of the device
covers.
• Do not cover the openings of the airflow covers. Air ventilation ensures
reliable and safe operation of the device.
There is a risk of electric shock!
There is a danger of fire!
Warning!
• Place the device in a place where children can not reach freely.
• Prevent children from handling the device. The device may overwhelm
children and cause serious injury.
• Mechanical damage (breakage or breakage of parts and covers) of the
device can cause serious injury.
There is a risk of serious injury!
There is a risk of damage to equipment or other property damage!
• Do not place or use the appliance near water-containing containers. If the
appliance falls into the water, do not remove it! First, pull the power cord
plug out of the mains socket and then select the appliance from the water.
In such cases, take the device for inspection to a specialist service to check
that it is safe and working properly.
There is a risk of electric shock!
There is a risk of electrical short circuit!
Operation/Supervision
Warning!
• This device must only be used with original parts and accessories.
• Always make sure that the device is properly assembled and that none
of its parts is damaged before using the appliance. Do not use incorrectly
assembled and damaged devices.
• Always use the appliance with a properly fitted lid / container cover.
• Only fill the container (primary filling with the uncovered container) when
the appliance is turned off. If you fill the foodstuff in the container during the
operation of the appliance, do so only through the filling opening (the lid) at
the age of the container.
• Always switch off and unplug the power cord from the wall outlet before
replacing the accessory or accessory parts of the device, before installing
and dismantling, and before cleaning and servicing.
There is a risk of serious injury!
• Always keep your device under control during use and operation!
• This device is not intended to be operated via a programmer, an external
time switch or a remote control, as there is a risk of fire when the device is
covered or incorrectly positioned.

9EN
• Do not switch the device on or off by plugging in or pulling out the power
cord from the AC outlet.
• Always connect the appliance to mains power supply for normal use, then
turn on the main power switch.
• When you have finished using the appliance, turn off the main switch and
then pull the mains cord out of the mains socket.
• Do not use the device if the main power switch does not work.
• The device is under dangerous voltage when the power supply is
connected.
There is a risk of serious injury!
• The device contains rotating parts with sharp edges - rotating knives.
Warning!
• Do not bend your fingers and do not place other objects in the work area -
inside the container and the rotating parts when it is in operation.
• If the workspace needs to be handled (cleaning the rotating parts of
the trapped food) - always only when the appliance is switched off,
disconnected from the power supply and the rotating parts are completely
stopped, use only the specified accessories of the appliance or a suitable
item, plastic knife, plastic spoon / squeegee. Do not use metal objects.
Warning!
• After switching off the drive, the drive of the rotating parts will recharge for a
certain amount of time. Always wait until the rotating parts stop completely
before handling the equipment or the container‘s workspace.
There is a risk of serious injury!
There is a risk of tearing / puncture of the fingers!
• Take care during use and operation of the appliance so that you do not
come into contact with the rotating parts with loose hair, free ornaments or
loose clothing.
There is a risk of serious injury!
• Do not connect the power cord to bundles. The power cord must remain
accessible for safe disconnection of the appliance from the power supply.
• Do not let the cord hang loose and do not allow it to be freely accessible
and reachable by children.
• Never leave your device freely accessible and do not leave it with a loose
cord. Children could download the device for a network cord.
• Do not store the appliance with a wrapped cord around your body. Unfold
the network cord „in the way it was put in the original packaging by the
manufacturer.
There is a risk of serious injury!
• Never overload the equipment beyond the limits specified by the technical
specifications!
• Do not switch on the appliance unless the container is filled with sufficient
fluid / food.

10EN
• Do not exceed the maximum content/volume of processed foods indicated
on the containers or recommended in the food process information in this
manual.
• Allow the food to cool before processing the heat treated food. Do not
process food with a temperature higher than 60C.
• Before processing deep-frozen foods, allow food to thaw first to the
temperature at which food can be divided into smaller (recommended)
parts. Do not process excessive pieces of deep-frozen food.
• Always divide the device to the recommended operating intervals and set
the operating mode (continuous operation/breakthrough time) and follow
these instructions.
• If you notice any unusual occurrences (vibrations, sounds, smells, smoke,
etc.) while using the device, switch off the device immediately and unplug it
from the mains. Have the appliance checked by a specialist workshop.
There is a risk of serious injury!
There is a risk of damage to equipment or other property damage!
• Only install and disassemble the device and its parts when the device is
switched off and disconnected from the mains.
There is a risk of serious injury!
• Always clean the equipment and accessories immediately after use and
dispose of all residues of processed food.
• Store the device in an upright position - especially its drive unit.
• If any safety component / component (mechanical, electrical / electronic)
is part of the device, never disable this part / component! If the safety
component / component is damaged or not working, do not use the
appliance!
• Do not use the safety parts / components for switching on or off. switch off
the device.
• The machine‘s operating time is 2 minutes. After 2 minutes, stop operation
for at least 2 minutes.
• Never underestimate the potential hazards and take extreme caution !!!

11EN
Technical specifications
Power supply: 230V~ 50 Hz
Power consumption: 500 W
Protection Class : II (protection against electric shock the current is
secured by double insulation)
Time of continuity of
operation (KB): 2 min.
Container capacity: 1,5 l liters for liquids
Dimensions (WxHxD): 95x395x60 mm
Weight: 2,97 kg
Cord length: approx. 1 m
Noise level: 80 dB (A)
The declared noise emission of this appliance is 80 dB (A), which is the sound power level
A with respect to the reference acoustic power of 1 pW.
The right to change is reserved!

12EN
Before first use
Do not plug the appliance into the mains during preparation. Unpack and
remove all packaging material from it.
The assembly of the glass container with the blades of the mixer is as
follows:
1. Place a silicone rubber seal over the knife assembly as shown in Figure 1.
2. Place the knife assembly in the lower part of the container so that the
inner protrusions in the plastic part of the bottom of the container fit into the
grooves of the knife assembly and then, by means of the locking cap (A),
can be rotated counterclockwise as shown in Figure 2.
3. Make sure that the knife assembly is firmly in place, as shown in Figure 3.
4. Use the opposite procedure to remove the knife assembly for cleaning
purposes.
To remove any dirt that may have occurred during the packing process, clean
the inside compartment, blades and cover with a dry cloth that does not
release the fibers. When cleaning the inside, be careful not to touch the sharp
knives. (See „Cleaning and maintenance“ in
this manual). Rinse the accessories in lukewarm water. Do not immerse the
body in water! Clean the surface with a cloth moistened with water.
Dry all parts thoroughly.
Never immerse the engine base in water or other fluid!
Only for the home use!
obrázok 1.
obrázok 2. obrázok 3.
A

13EN
A. Locking hole cap
B. Mixerl cover
C. Glass mixer with a measuring cup
D. Mixer blades
E. Base with engine
F. Power switch P, 0 (off), I, II
G. Rubber legs
A
B
C
D
E
F
G
P Pulse mode (unreturned
position)
0 Off position
I Low Speed
II High Speed
Parts descriptions

14EN
Assembly accessories and fitting to the engine unit
Follow the steps below to set up a food processing appliance.
1. Place the base on a dry, level and firm surface. Do not plug the power cord
into an electrical outlet before fully assembling the device!
2. Insert the blade shaft into the center hole of the bottom of the container and
screw the special nut with the left-hand thread. The knives are factory-fitted.
3. Place the cover with the hole on the container. Insert the cap into the hole
and turn it to the right to lock it.
4. Push the mixer container onto the base with the knives and turn it to
the right so that it mounts firmly and correctly on the base. The mixer is
ready for use. Note: Follow the procedure below. Otherwise, the mixer will
not work! Slide the door on the engine unit back to the rear and turn the
container 90 ° to the right to lock it securely.
5. Place the food you mix into the container and place the two-element cover
on the container.
Put only one cup of food at a time (meat, vegetables, nuts, etc.). Remove
the larger pieces of food before processing into approximately 2.5 cm of
cube.
Do not work more than 1 cup of food at the same time!
6. Plug the power cord into an electrical outlet.
7. For continuous mixing, set the switch to one of the power positions.
For manual mixing, slide the switch to P for the required time.
8. If you add liquid to the bowl while processing the food, attach it through the
neck in the cover.
Note: The maximum volume of liquid added must not exceed three cups.
If you need to open a mission on processing. Turn the machine off and
wait for the knife to stop. Other foods can be added through the neck in the
cover, without the need to open the cover.
Warning: Turn off the device and wait for the knife to stop!
9. When you have finished working, disconnect the power cord from the
electrical outlet.
When opening the container cover, grasp the device firmly and turn the
cover to the left to release it.
10. When removing food from the container, beware of the knives. Handle the
knives carefully. They are sharp!
Turn the bowl to the left. Then, pull the handle by pulling it out of the base.
Remove the food residue from the container and knife with a rubber blade.

15EN
Tips for effective blending
Prior to insertion into the container, the hard fruit and vegetables must be
cut to pieces approximately 1 cm in size. Even safer food types should be
pre-cut to smaller pieces before mixing. Increase efficiency of mixing. If you
are preparing multiple ingredients, requiring mixes of different ingredients at
different rates, mix the individual ingredients separately.
• For fruit/vegetable slicing, place fruit/vegetables in a container of about 2
cups. Mix continuously in position I or II or switch the switch to position P
until you reach the desired consistency.
• For fruits/vegetables, add about 1 cup of liquid for hard fruit/vegetables
. Add about 1/2 cup of liquid to 1 cup of fruit/vegetables to the soft fruit/
vegetables.
• Avoid pre-mixing. Mix in a few seconds, not minutes. Premixing produces a
mash consistency.
• Do not fill the mixing bowl. Fill up to 5 cups in the container.
• Fill the container with liquid first, then solids (unless the recipe prescribes
otherwise).
• To add food or ice to the container during mixing, open the middle cover of
the two-piece cover and add the food through the opening.
• When mixing beverages, you can put all ingredients into the container at
the same time.
• When mixing solid food, cross the food to small pieces (about 1 cm) and
add it through the cover hole.
• Add ice in one cube during mixing. After mixing, you can add another cube.
When mixing, hold the container gently with your hand.
• Only mix ice when there is fluid in the container. Use two cups of water.
• If the mixing stops during operation, turn off the appliance, fold the
container cover, and select the contents of the container using the
squeegee (s).
• We recommend adding a sufficient amount of water for mixing potatoes
Warning:
• Never mix with open container cover!
• Never mix for more than 2 minutes! After 2 minutes of mixing, turn off the
device, give it a 2-minute pause and continue.

16EN
Overview of quantities of processed foods
Processed Food Quantity per Dose
Chocolate Max. 100 g
Cheese Max.200 g
Meat Max. 500 g
Tea or spice 50 ~ 100 g
Vegetables and fruits 100 ~ 300 g
Onions Max. 500 g
Flour Dough/Soft Cheese Max. 300 g Eggs Max. 5 pcs
Preparation times and speed settings
Ingredience Speed Mixing time
Baby food, sauces 1 45 s.
Cocktails, smoothie 2 40 s.
Soups 2 30 s.
Spreads, dressing 1 30 s.
Ice cubes P
The time for ingredients to be processed depends on how thoroughly you
want to mix the embedded food.
Cleaning and maintenance
When the mixing is complete, disconnect the appliance from the mains.
Remove all parts from the container. Fill the container with water with a
detergent solution and close the container with the covers. Plug the appliance
into the mains and mix it at the highest power.
If necessary, repeat the procedure.
Do not put parts of the appliance in the dishwasher or boiling water. The
blade on the mixing knives is plastered with a durable grease. However, this
is gradually eliminated in the boiling water. Subsequently, bearing life may
shorten.
Never immerse the base or engine in water or other fluid!
Use a dry cloth on the base with the motor and the power cord. Do not use
solvents or harsh cleaners to clean any components.

17EN
Procedure for dismantling the glass container with the
knife assembly
1. Remove the glass container from the engine base and without the center
locking cap, place it on the table opposite.
2. Attach the locking cap (A) to the center of the knife assembly until it
stops as far as it will go.
3. Rotate the lock cap (A) to the right to release the whole knife assembly
and remove it from the glass container.
4. Clean the glass and blade assembly with the reverse procedure (page 5).
We recommend that the silicone sealant be moistened during assembly.
A
1
2

18EN
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT
The symbol on the product or on its packaging indicates that this product does not belong
to household waste. It is necessary to take it to a collection point for electrical recycling
and electronic equipment.
By ensuring proper disposal of this product, you will help prevent negative consequences
to the environment and human health that would otherwise be caused by inappropriate
disposal of this product. For more detailed information about recycling of this product,
please contact your local authority, your household waste disposal service or the shop
where you purchased the product.
This product meets all the essential requirements of the EU directives that apply to it.
Producer:
Importer:
ORAVA retail 1, a.s.
Seberíniho 2
821 03 Bratislava
Slovenská republika
ORAVA distribution CZ, s.r.o.
Ostravská 494
739 25 Sviadnov
Česká republika
ORAVA retail 1, a.s.
Seberíniho 2
821 03 Bratislava
Slovenská republika