Orbit Controls OC 7040A User manual

OC7040A_GB_21002
Process Controller
OC 7040A
Owner’s Manual
ORBIT CONTROLS AG
Zürcherstrasse 137
CH-8952 Schlieren/ZH
Tel: + 41 44 730 2753
Fax: + 41 44 730 2783
[email protected]
www.orbitcontrols.ch

2

Vor dem Einschalten
Überzeugen Sie sich, ob Ihre Sendung das richtige Gerät Orbit Controls Modell OC 7040A beinhaltet,
einschliesslich einer Betriebsanleitung OC 7040A.
Vor dem Einschalten des Gerätes überprüfen Sie die Anschlüsse und die Versorgungsspannung. Ein
falsch angeschlossenes Gerät kann beschädigt werden und damit auch die mitverbundene
Folgeelektronik. Für falsche Handhabung wird jede Haftung abgelehnt.
ZU BEACHTEN
Dieses Gerät wurde sorgfältig verpackt. Falls es bei Ihnen in beschädigtem Zustand eintrifft,
benachrichtigen Sie unverzüglich den Orbit Controls Kundendienst (Tel: [phone] oder
Fax: [phone]) und nehmen Sie einen Schadenrapport auf, welchen Sie auch von der
Transportgesellschaft unterschreiben lassen. Bewahren Sie bitte das Verpackungsmaterial für
eventuelle Reklamationen auf.
Unpacking Instructions
Remove the Packing List and verify that you have received all equipment, including the following:
Orbit Controls Model OC 7040A Programmable Controller.
Operator's Manual OC 7040A.
If you have any questions about the shipment, please call the Orbit Controls Customer Service
Department.
NOTE
When you receive the shipment, inspect the container and equipment for signs of damage. Note
any evidence of rough handling in transit. Immediately report any damage to the Orbit Controls
customer service, Phone [phone] or Fax [phone] and to the shipping agent.
The carrier will not honor damage claims unless all shipping material is saved for inspection. After
examining and removing contents, save packing material and carton in event the reshipment is
necessary.
3

INDEX
Page
PROGRAMMABLE CONTROLLER OC7040A 5
1 KEYBOARD 5
2 SPECIFICATIONS 6
3TERMINALS 7
4MENU 7
5 CONNECTION EXAMPLES 9
5.1 Process Signal 0/4-20mA 9
5.2 Two Terminal Sensor 9
5.3 RTD Thermometer 9
5.4 Thermocouples and Thermistors 9
5.5 Strain Gauge with Current Supply 9
5.6 Strain Gauge with Voltage Supply 9
5.7 Range Selection 10
5.8 Supply Voltage Selection 115/230VAC 11
6 SERVICE MENU - HtESt 12
7CALIBRATION 13
7.1 Calibration of linear Signals DC and AC 13
7.2 calibration of non-linear Signals (Tables) 13
7.2.1 Calibration of Pt-100 Thermometers 13
7.2.2 Calibration of Thermocouples 13
7.3 Calculation of R19 13
8 BURST TEST and RECOMMENDED CONNECTION 14
4

PROGRAMMABLE CONTROLLER OC 7040A
6 digit display ±999999  free programmable
 ±100 000 true increments  two point calibration
DC voltage and current ranges RS 232 and RS 485
AC true RMS ranges Analog Outputs 0/4-20mA, 0-10V
Four Set Point Relays
 Excitation
 AC or DC supply
Orbit Controls OC7040A is a programmable 6 digit
instrument for DC and AC voltages and currents,
linear potentiometers, temperature sensors and
signals from various analog sensors and sources.
The measured and displayed results are converted
into two analog outputs and two serial data strings
for further usage.
With the keyboard the menu can be opened and the
process parameters set for the required application.
The menu contains the function of the display, the selection of the analog outputs, parameters of the
serial data ports, setting of the set points, and assignment of the input signal to the display. A Tara
function is available for setting the display to zero at any measuring point.
For supplying of external sensors an adjustable Excitation is available.
Service Menu HtESt is suitable for checking of the instrument’s performance and the calibration.
1 KEYBOARD
Key Function in Measuring Mode
UP Maximum stored value appears at the display.
1,2,3,4 Set Points
P Program Mode
MENU
ACK
UP
DOWN
SET
DOWN Minimum stored value appears at the display.
ACK Memory reset.
OPTION:
Peak Memory - Display Functions
Dir The Display shows momentary signal value. Selection with ACK.
UPP The Display shows continuously the maximum measured value. Selection with UP.
LOW The Display shows continuously the minimum measured value. Selection with DOWN.
Reset of Peak Memory
To reset the Peak Memory press UP or DOWN and immediately press the key SET for approx. 3 sec until the
display shows SET. The Peak Memory is empty and the display shows the value of the signal at the input.
5

2 SPECIFICATIONS
Display: 0 ... ±999999, 7 segment red 14.7 mm display units with decimal point.
Input: The input is set at the factory for DC or AC voltage or current, RTD or thermocouples,
Potentiometers or Resistor Measurement.
Voltage ±100mV to 300V DC or true RMS.
Option: 20mVDC for strain gauges
Current 0/4-20mA, ±20mA to 5A DC or true RMS.
Pt-100/200 2 or 4 wire. -200...+650°C according to PT385.
OHM 10Ω-100k Ω, 2 or 4 wire connection
T/C E, J, K, S, B, C, T, according to DIN.
Cold Junction automatic compensation 0 - 60°C.
Thermistors 9796Ω@ 0ºC and 27936Ω @ 0ºC
ADC: 19 bit, bipolar, sampling time 63ms.
Integral Nonlinearity: ±0.006% of range
Zero Error: ±0.0168% of range
Rollover Error: ±0.032% of range
Tempco: ±10ppm°C
Linearity: ±(1 LSB + 1 digit).
Accuracy DC Ranges ±(0.01% from value + 2 digit)
True RMS 50Hz - 5 kHz: ±(0.1%from value + 2 digits).
Pt-100 and T/C Pt-100/200: ±(1°C+1 digit)
T/C, Thermis: ±(2°C+1 digit)
Tempco: ±25 ppm/ °C.
Set Points: Standard: Set Point Relay SP1, SP2, 5A-230VAC.
Option: Additional Relays SP3, SP4, 5A-230VAC.
Setting range: ±999999.
Each Set Point has adjustable Hysterese from 0 to 99.
Analog Output: Option: Analog Outputs 0/4-20mA and 0...±10V, 12 bit resolution (Option 16 bit).
Isolation 250V RMS.
Data Output: Option: RS232 or RS485 with addresses 01-31, 8 bit, 1 Start, 1 Stop, No Parity.
Baud Rate 600 … 19200 bd. Isolation 250V RMS.
RS232: The data are transmitted continuously or per request.
Continuous Transmission: Terminal P (RSI) tied to +5V against N (GND).
Request Transmission: Terminals P (RSI), R (RSO) and N (GND) connected
to PC D-SUB terminals 3, 2 and 5, - see page 6.
The data are transmitted after <CR> <LF> (ENTER).
Excitation: Voltage: Isolated and adjustable 5 ... 24 V/40mA
Current: Constant source of 1mA for RTD and Resistance Measurements
Supply: 115V / 230V ±10%, 48-60 Hz. Option 9-36VDC-4W.
Cabinet: DIN 48x96x100 mm (H x W x D), Panel cut-out 45 x 90 mm. IP65 front protection.
Terminals: Pluggable Terminal Blocks
6

3 TERMINALS
RS232 Request Transmission
RS232 Continuous Transmission
4 MENU
The key MENU opens the Menu. The required parameter will be confirmed with ACK. .
With UP or DOWN the parameters will be set.
The flashing digit - Cursor - can be positioned with ACK. The sign and the decimal point can be set after
the cursor is positioned outside the display range (none of the digit is flashing).
The key UP sets the decimal point, the key DOWN sets the sign. The key SET terminates the
programming and the display returns to the measuring mode.
KEY DISPLAY FUNCTION
MENU PASS Password selection from 20 stored combinations
ACK P 0200 Select with UP or DOWN
MENU OrdEr Decimal Point, Display Resolution
ACK CCCC.dd Select with UP or DOWN
MENU Fn tArA Tara function OFF, ONLY or ON.
ACK ONLY After pressing the key SET the display will be forced to zero
ON The key SET pressed once forces the display to zero. When pressed for
second time, the display returns to the non-tare original signal value.
MENU FiltEr Setting of filter constant (averaging filter type)
ACK OFF Selection: OFF and 1, 2….99
MENU Count Counting of the last digit:
ACK 0 Dummy Zero
1 The display increments 1, 2, 3….9, 0
2 The display increments 2, 4, 6…
5 The display increments 0,5,0,5…
MENU dSP Display refresh after selected number of measurements
ACK 1 Selection: 1, 2….50
MENU SP 1 Set Point SP1
ACK XXXXXX Selection: -999999 to 999999. The relay is activated when the display
arrives at the SP1 or higher values
MENU HSt 1 SP1 Hysterese
7

ACK XXXXXX Selection: -999999 to 999999
MENU FnrL1 Function of the relay SP1
ACK OPEN Selection between OPEN or CLOSE at the alarm conditions
MENU SP 2 Set Point SP2
ACK XXXXXX Selection: -999999 to 999999. The relay is activated when the display
arrives at the SP1 or higher values
MENU HSt 2 SP2 Hysterese
ACK XXXXXX Selection: -999999 to 999999
MENU FnrL2 Function of the relay SP2
ACK OPEN Selection between OPEN or CLOSE at the alarm conditions
Options SP3 and SP4 are configured as SP1 and SP1.
MENU Aout L Display value for Analog Output 0 (-10) V and 0/4mA
MENU Aout H Display value for Analog Output 10V and 20mA
The Output 0-10V or -10…10V are jumper selectable
MENU SEt SEn Selection of the type of linearization
LinEAr linear type of characteristic for DC- and AC inputs.
POLYn Polynom Linearizing
tAbtAb X-Y Table assignement of input signal to display reading
Pt 100 RTD thermometer
tEr3t Thermistor 9796 Ohm @ 0 ºC
tEr5t9 Thermistor 27936 Ohm @ 0 ºC
tC E Thermocouple E with external could junction
tCC E Thermocouple E with internal could junction
tC J Thermocouple J with external could junction
tCC J Thermocouple J with internal could junction
tC L Thermocouple K with external could junction
tCC L Thermocouple K with internal could junction
tC S Thermocouple S with external could junction
tCC S Thermocouple S with internal could junction
tC b Thermocouple B with external could junction
tCC b Thermocouple B with internal could junction
tC t Thermocouple T with external could junction
tCC t Thermocouple T with internal could junction
tC C Thermocouple C with external could junction
tCC C Thermocouple C with internal could junction
Cold Cold junction temperature measured and displayed
MENU Set in 0.0 1 Setting for bipolar inputs, e.g. ±1V and 0-20mA
0.2 1 Setting for shifted inputs, e.g. 4-20mA.
-1 1 Setting for bipolar input signals, e.g. –20 ... +20V.
MENU Set LO Required display value for the minimum input signal (e.g. 4mA)
MENU Set HI Required display value for the maximum input signal (e.g. 20mA)
MENU bAUd Baud rate of the data port
ACK 1200 Selection: 1200 to 19200 bd
MENU Contin Transmission Mode
ACK OFF On = continuous transmission, OFF=request transmission
MENU rS Adr Address of the RS485 data port
ACK rS 232 RS232 is activated with address 00
31 RS485 is activated with one of addresses 01 … 31
MENU StPASS Password selection from 20 stored combinations
MENU Start Measuring mod
8

5 CONNECTIONS EXAMPLE
5.1 Process Signal 0/4-20mA 5.2 Two Terminal Sensor
5.3 RTD Thermometer and Ohmmeter 5.4 Thermocouples and Thermistors
5.5 Differential input 5.6 Strain Gauge with voltage supply
9

5.7 Range Selection
Jumper 20mA 1V 10V 100V 10mV-1V
H1 1+2 1+2 2+3 2+3 1+2
Z8 , Z9 DC= Z8 close, Z9 open AC= Z8 open, Z9 close
H3 1+2 --- --- 2+3 ---
R19 (page 11, § 7.3) open open open open R=50k/G-1
Input single ended (+)15, (-)14,13 (+)15, (-)14,13 (+)15, (-)14,13 (+)15, (-)14,13 (+)15, (-)14,13
Input differential --- (+)15, (-)13 --- --- (+)15, (-)13
10

5.8 Supply Voltage Selection115/230VAC. Solder Side of the Printed Board.
115VAC: X2 = X3 = closed 230VAC: X1 = closed
X1 = open X2 = X3 = open
11

6 SERVICE MENU - HtESt
The Service Menu HtESt permits fast check of the instrument’s performance and offers the software
calibration via the keyboard. To enter the Service menu, keep the key MENU pressed while the
instrument is switched-on. Release the key when the display shows HtESt. The service menu steps are
incremented forward with the key MENU, decremented backward with SET.
In the service menu the digit segments are tested first. After the HCF value can be entered (see bellow).
Than the signal channel can be calibrated. The set point relays and the display LEDs are activated. At
the end the analog outputs are generated.
Segments all segments are activated
HCF.128 HCF parameter defines the range of the menu. The menu without options Analog Output,
Set Points and RS data ports is determined with HCF = 128. Each option is activated in
the menu with binary value added to the HCF 128:
1 SP1
2 SP2
4 SP3
8 SP4
16 Analog output
32 Baud rate
64 Address of the data port
Combinations define the menu range:
HCF.144 Menu (128) and Analog Output (16).
HCF.240 Menu (128), Analog Output (16), Baud rate (32) and Address (64).
AdC ADC internal DC value of the converter.
ATTENTION! The input signal has to be set to ZERO before this Step is entered!
1.25XXX Apply the zero signal value. The display shows the internal voltage reference 1.25V.
The Zero Value will be calibrated when the key DOWN is pressed. The display shows
Ac LO. Press the key ACK and keep it pressed until the display shows EE StO.
The Zero Signal Value has been calibrated.
2.2XXXX The Maximum Signal Value will be calibrated when the full range signal is applied and the
keyUP is pressed. The display shows AC HI. Press the key ACK and keep it pressed
until the display shows EE StO.
The maximum signal value has been calibrated.
rES The Display shortly shows rES and switches into the measuring mode. The display
corresponds to the SEt HI programmed value in the main menu.
COL. X Correction of the cold junction temperature.
SP1 Set Point 1 and the Relays 1 are activated.
SP2 Set Point 2 and the Relays 2 are activated.
SP3 Set Point 3 and the Relays 3 are activated.
SP4 Set Point 4 and the Relays 4 are activated.
An - 10 Analog Output -10V and 0/4 mA are generated (0 or 4mA selectable).
An - 5 Analog Output -5V and 5/8 mA are generated.
An 0 Analog Output 0V and 10/12 mA are generated.
An 5 Analog Output 5V and 15/16 mA are generated.
An 10 Analog Output 10V and 20 mA are generated.
StArt Measuring Mode
12

7 CALIBRATION
7.1 Calibration of linear signals DC and AC
The calibration steps are described in §6, Service Menu and HtESt. Linear signals such as 4-20mA, 0-
1V can be calibrated as described.
7.2 Calibration of non-linear signals (Tables)
Input signals such as RTD Thermometer and Thermocouples will be linearized as follows:
7.2.1 Calibration of Pt-100 Thermometer SEnS LinEAr
Set LO 0
Set HI 100
In the HtESt calibrate with 0 Ohm and 100 Ohm. After the
calibration is finished, switch OFF and ON again.
SEnS select Pt 100 in the Menu.
Switch into the measuring mode with ACK. The Display follows the
temperature of Pt-100 in a range from -200 to 600ºC.
7.2.2 Calibration of Thermocouples
Jumper Pt-100
H1 1 + 2
Z8 closed
Z9 open
H3 ---
R19 18k Resistor 1%
Jumper Thermocouples
H1 1 + 2
Z8 closed
Z9 open
H3 ---
R19 5k6 Resistor 1%
SEnS LinEAr
Set LO 0
Set HI 100 (100 = 100 mV)
In the HtESt calibrate with 0 und 100mV. After the calibration is
finished, switch OFF and ON again.
SEnS Select the required T/C in the Menu. Switch into the
measuring mode with ACK. The Display follows the temperature of
the selected T/C within its defined range.
The cold junction is compensated with SMT160 connected to the
terminal block.
7.3 Calculation of R19
When the individual measuring range by using R19 is selected, following has to be considered:
The AD-C type LT2400 is designed for bipolar operation. Its zero reference point is set to +1.25V. Since
R19 determines the gain of the input amplifier INA118, its output signal (Pin 6) has to be within 0 and
2.500V for the full range of the input signal. For Zero input is Pin 6 = 1.25V. For maximum negative input
is Pin 6 = 2.500V. For maximum positive input is Pin 6 = 0V. It is important to calculate R19 such that the
signal swing at the output of INA118 (Pin 6) never goes bellow 0V and above 2.500V.
The calibration mode in the HtESt shows the range of the input signal (§ 6). When zero signal is applied,
the display shows the reference voltage of 1.25xx V. With a maximum signal the display will show
2.500V. It is recommended to set R19 such that the display arrives at 2.2xxx with the maximum value of
the input signal. This will permit 10% overload of the input.
G=Gain
13

8 BURST TEST and RECOMENDED GROUNDING
Tester: Burst-Surge Generator HILO, Model CE-Tester
E.U.T.: OC7040, SN: 980315, Supply 230VA
Mode: Linear, Set LO = 000000, Set HI = 10000
Input: 4-20mA
Display: 10 000
8.1 Test Conditions
According to: IEC 801-4
IEC 1000-4-4
EN 50052-1
8.2 Test Set - Up
8.3 Test Results
Zone 1: 2kV Burst Display 10 000 without change
Zone 2: 2kV Burst Display 10 000 without change
CE Approval No: 321/30-3/539, c.j. 9004/69 from 15.6.1998 VTUE Praque
14