ORION TELESCOPES & BINOCULARS SpaceProbe 130ST EQ 9007 User manual

IN 147 Rev A 0700
Providing Exceptional Consumer Optical Products Since 1975
Customer Support [phone]
E-mail: [email protected]
Corporate Offices [phone]
P.O. Box 1815, Santa Cruz, CA 95061
INSTRUCTION MANUAL
Orion®
SpaceProbe 130ST EQ
Equatorial Newtonian Reflector Telescope
#9007

2
Figure 1. Space Probe 130 ST parts diagram
Dovetail slot
Finder scope Alignment thumb screws(2)
Spring-loaded tensioner
Finder scope bracket
Piggyback adapter
Tube mounting rings
Tube ring clamps
Primary mirror cell
Collimation
screws(6)
R.A. setting circle
Latitude adjustment t-bolt
Azimuth lock knob
Leg lock knob
Accessory tray
Accessory tray bracket
Eyepiece
Focuser
Dec. slow-motion
control cable
Dec. setting circle
R.A. lock knob
Counterweight
Counterweight lock knob
Counterweight shaft
R.A. slow motion control cable

3
1. Unpacking
The entire telescope system will arrive in one box.Be careful
unpacking the box.We recommend keeping the original ship-
ping containers.In the event that the telescope needs to be
shipped to another location, or returned to Orion for warranty
repair, having the proper shipping containers will help ensure
that your telescope will survive the journey intact.
Make sure all the parts in the Parts List are present. Be sure
to check boxes carefully, as some parts are small. If anything
appears to be missing or broken, immediately call Orion
Customer Support (800-676-1343) for assistance.
2. Parts List
Qty. Description
1 Optical Tube Assembly
1 Optical tube dust cap
2 Optical tube mounting rings
1 25mm (36x) Explorer II eyepiece (1.25")
1 10mm (90x) Explorer II eyepiece (1.25")
1 6x30 crosshair finder scope
1 Dovetail finder scope bracket with O-ring
1 Equatorial mount
3 Tripod legs with attachment bolts
3 Leg lock knobs (may already be on tripod legs)
1 Counterweight shaft
1 Counterweight
1 Tripod accessory tray
3 Accessory tray wing screws (may be attached to
accessory tray)
2 Slow-motion control cables
4 Assembly tools (2 wrenches, Phillips head screw
driver, flat head screwdriver key)
C ongratulations on your purchase of a quality Orion telescope .Your new SpaceProbe 130mm EQ is
designed for high-resolution viewing of astronomical objects.With its precision optics and equatorial
mount, you’ll be able to locate and enjoy hundreds of fascinating celestial denizens, including the plan-
ets, Moon, and a variety of deep-sky galaxies, nebulas, and star clusters.
If you have never owned a telescope before, we would like to welcome you to amateur astronomy.Take
some time to familiarize yourself with the night sky. Learn to recognize the patterns of stars in the major
constellations.With a little practice, a little patience, and a reasonably dark sky away from city lights,
you’ll find your telescope to be a never-ending source of wonder, exploration, and relaxation.
These instructions will help you set up, properly use and care for your telescope.Please read them over
thoroughly before getting started.
WARNING: Never look directly at the Sun
through your telescope or its finder scope—even
for an instant—without a professionally made solar
filter that completely covers the front of the
instrument, or permanent eye damage could result.
Be sure to also cover the front of the finder scope
with aluminum foil or another opaque material to
prevent physical damage to the internal
components of the scope itself as well as to your
eye.Young children should use this telescope only
with adult supervision.
Table of Contents
1. Unpacking.............................................................................................................................. 3
2. Parts List................................................................................................................................ 3
3. Assembly............................................................................................................................... 4
4. Getting Started ...................................................................................................................... 5
5. Setting Up and Using the Equatorial Mount .......................................................................... 7
6. Collimating the Optics.......................................................................................................... 10
7. UsingYourTelescope–Astronomical Observing .................................................................. 12
8. Care and Maintenance ........................................................................................................ 15
9. Specifications ...................................................................................................................... 16

4
3. Assembly
Assembling the telescope for the first time should take about
30 minutes.No tools are needed other than the ones provid-
ed. All bolts should be tightened securely to eliminate flexing
and wobbling, but be careful not to over-tighten or the threads
may strip.Refer to Figure 1 during the assembly process.
During assembly (and anytime, for that matter), DO NOT
touch the surfaces of the telescope mirrors or the lenses of
the finder scopes or eyepieces with your fingers.The optical
surfaces have delicate coatings on them that can easily be
damaged if touched inappropriately. NEVER remove any lens
assembly from its housing for any reason, or the product war-
ranty and return policy will be voided.
1. Lay the equatorial mount on its side.Attach the tripod legs
one at a time to the mount by sliding the bolts installed in
the tops of the tripod legs into the slots at the base of the
mount and tightening the wing nuts finger-tight.Note that
the accessory tray bracket attachment point on each leg
should face inward.
2. Tighten the leg lock knobs on the bottom braces of the tri-
pod legs. For now, keep the legs at their shortest (fully
retracted) length;you can extend them to a more desirable
length later, after the telescope is completely assembled.
3. With the tripod legs now attached to the equatorial mount,
stand the tripod upright (be careful!) and spread the legs
apart enough to connect each end of the accessory tray
bracket to the attachment point on each leg.Use the screw
that comes installed in each attachment point to do this.
First remove the screw using the supplied screwdriver,
then line up one of the ends of the bracket with the attach-
ment point and reinstall the screw. Make sure that the
smooth side of the accessory tray bracket faces upwards.
4. Now, with the accessory tray bracket attached, spread the
tripod legs apart as far as they will go, until the bracket is
taut. Attach the accessory tray to the accessory tray
bracket with the three wing screws already installed in the
tray.This is done by pushing the wing screws up through
the holes in the accessory tray bracket, and threading
them into the holes in the accessory tray.
5. Next, tighten the bolts at the tops of the tripod legs, so the
legs are securely fastened to the equatorial mount. Use
the larger wrench and your fingers to do this.
6. Orient the equatorial mount as it appears in Figure 2, at
a latitude of about 40°, i.e., so the pointer next to the lati-
tude scale (located directly above the latitude lock t-bolt)
is pointing to the hash mark at “40.”To do this, loosen the
latitude lock t-bolt, and turn the latitude adjustment t-bolt
until the pointer and the “40” line up.Then retighten the
latitude lock t-bolt.The declination (Dec.) and right ascen-
sion (R.A.) axes may need re-positioning (rotation) as
well.Be sure to loosen the RA and Dec.lock knobs before
doing this.Retighten the R.A. and Dec. lock knobs once
the equatorial mount is properly oriented.
7.Slide the counterweight onto the counterweight shaft.Make
sure the counterweight lock knob is adequately loosened
to allow the counterweight shaft to pass through the hole
in the counterweight.
8. Now, with the counterweight lock knob still loose, grip the
counterweight with one hand and thread the shaft into the
equatorial mount (at the base of the declination axis) with
the other hand.When it is threaded as far in as it will go,
position the counterweight about halfway up the shaft and
tighten the counterweight lock knob.The retaining screw
and washer on the bottom of the shaft prevent the coun-
terweight from falling off (and onto your foot!) if the
counterweight lock knob becomes loose.
9. Attach the two tube rings to the equatorial head using the
bolts that come installed in the bottom of the rings. First
remove the bolts, then push the bolts, with the washers
still attached, up through the holes in the tube ring mount-
ing plate (on the top of the equatorial mount) and rethread
them into the bottom of the tube rings.Tighten the bolts
securely with the smaller wrench. Open the tube rings by
first loosening the knurled ring clamps. One of the tube
rings has a piggyback camera adapter on top (the knurled
black ring); it can be used to mount a camera for “piggy-
back” astrophotography.
10.Lay the telescope optical tube in the tube rings at about
the midpoint of the tube’s length. Rotate the tube in the
rings so the focuser is angled somewhere between hori-
zontal and straight up. Close the rings over the tube and
tighten the knurled ring clamps finger-tight to secure the
telescope in position.
11.Now attach the two slow-motion cables to the R.A. and
Dec. worm gear shafts of the equatorial mount by posi-
tioning the thumb screw on the end of the cable over the
indented slot on the worm gear shaft and then tightening
the thumb screw.We recommend that the shorter cable
be used on the R.A.worm gear shaft and the longer cable
on the Dec. worm gear shaft.The Dec. worm gear shaft
RIGHT ASCENSION
AXIS
Azimuth lock knob
R.A. setting
circle lock
thumbscrew
DECLINATION AXIS
Figure 2. The Space Probe’s equatorial mount.
Dec. slow-
motion control
cable
Dec. lock knob
Dec. setting
circle
R.A. slow-
motion
control cable
R.A. setting
circle
Latitude scale
Latitude lock
t-bolt
Latitude adjust-
ment t-bolt

and cable should extend toward the front (open) end of
the telescope optical tube.If it does not, you will need to
remove the tube from the mounting rings, rotate the mount
180° about the Dec. axis (first loosen the Dec. lock knob),
and then replace the tube.
12.To place the finder scope in the finder scope bracket, first
unthread the two black nylon screws until the screw ends
are flush with the inside diameter of the bracket.Place
the O-ring that comes on the base of the bracket over
the body of the finder scope until it seats into the groove
on the middle of the finder scope.Slide the eyepiece end
(narrow end) of the finder scope into the end of the
bracket's cylinder that does not have the alignment
screws while pulling the chrome, spring-loaded tension-
er on the bracket with your fingers.Push the finder scope
through the bracket until the O-ring seats just inside the
front opening of the bracket’s cylinder. Now, release the
tensioner and tighten the two black nylon screws a cou-
ple of turns each to secure the finder scope in place.
13.Insert the base of the finder scope bracket into the dove-
tail slot near the focuser. Lock the bracket into position by
tightening the knurled thumb screw on the dovetail slot.
14.Remove the cap from the focuser and insert the chrome
barrel of one of the eyepieces into the drawtube. Secure
the eyepiece with the thumb screws on the drawtube.
Remember to always loosen the thumb screws before
rotating or removing the eyepiece.
The telescope system is now fully assembled.Keep the dust
cap over the front end of the telescope when it is not in use.
4. Getting Started
Balancing the Telescope
To insure smooth movement of the telescope on both axes of
the equatorial mount, it is imperative that the optical tube be
properly balanced. We will first balance the telescope with
respect to the R.A. axis, then the Dec. axis.
1. Keeping one hand on the telescope optical tube, loosen
the R.A. lock knob. Make sure the Dec. lock knob is
locked, for now. The telescope should now be able to
rotate freely about the R.A. axis. Rotate it until the coun-
terweight shaft is parallel to the ground (i.e., horizontal).
2. Now loosen the counterweight lock knob and slide the
weight along the shaft until it exactly counterbalances the
telescope (Figure 3a).That’s the point at which the shaft
remains horizontal even when you let go of the telescope
with both hands (Figure 3b).
5
b. d.
c.
a.
Figure 3A, 3B, 3C, 3D: Proper operation of the equatorial mount requires that the telescope tube be balanced on both the R.A. and Dec. axes.
(a) With the R.A. lock knob released, slide the counterweight along the counterweight shaft until it just counterbalances the tube. (b) When you
let go with both hands, the tube should not drift up or down. (c) With the Dec. lock knob released, loosen the tube ring lock clamps a few turns
and slide the telescope forward or back in the tube rings. (d) When the tube is balanced about the Dec. axis, it will not move when you let go.

6
3. Retighten the counterweight lock knob.The telescope is
now balanced on the R.A.axis.
4. To balance the telescope on the Dec. axis, first tighten
the R.A.lock knob, with the counterweight shaft still in the
horizontal position.
5. With one hand on the telescope optical tube, loosen the
Dec. lock knob. The telescope should now be able to
rotate freely about the Dec. axis. Loosen the tube ring
clamps a few turns, until you can slide the telescope tube
forward and back inside the rings (this can be aided by
using a slight twisting motion on the optical tube while you
push or pull on it) (Figure 3c).
6. Position the telescope so it remains horizontal when you
carefully let go with both hands.This is the balance point
(Figure 3d). Before clamping the rings tight again, rotate
the telescope so the eyepiece is at a convenient angle for
viewing.When you are actually observing with the tele-
scope, you can adjust the eyepiece position by loosening
the tube rings and rotating the optical tube.
7. Retighten the tube ring clamps.The telescope is now bal-
anced on both axes.Now when you loosen the lock knob
on one or both axes and manually point the telescope, it
should move without resistance and should not drift from
where you point it.
Focusing the Telescope
Insert the low-power 25mm eyepiece into the focuser and
secure with the thumb screws. Move the telescope so the
front (open) end is pointing in the general direction of an
object at least 1/4-mile away. Now, with your fingers, slowly
rotate one of the focusing knobs until the object comes into
sharp focus.Go a little bit beyond sharp focus until the image
just starts to blur again, then reverse the rotation of the knob,
just to make sure you’ve hit the exact focus point.
If you have trouble focusing, rotate the focus knob so the draw-
tube is in as far as it will go. Now look through the eyepiece
while slowly rotating the focus knob in the opposite direction.
You should soon see the point at which focus is reached.
Do You Wear Eyeglasses?
If you wear eyeglasses, you may be able to keep them on
while you observe, if your eyepieces have enough “eye relief”
to allow you to see the whole field of view.You can try this by
looking through the eyepiece first with your glasses on and
then with them off, and see if the glasses restrict the view to
only a portion of the full field. If they do, you can easily
observe with your glasses off by just refocusing the telescope
the needed amount.
Aligning the Finder Scope
The finder scope must be aligned accurately with the tele-
scope for proper use.To align it, aim the main telescope in
the general direction of an object at least 1/4-mile away, such
as the top of a telephone pole, a chimney, etc. Do this by first
loosening the R.A.and Dec.lock knobs.Position the telescope
so the object appears in the eyepiece's field of view and then
retighten the R.A. and Dec. lock knobs.Use the slow-motion
control cables to center the object in the eyepiece.
Now, look in the finder scope.Is the object visible? Ideally, it
will be somewhere in the finder’s field of view.If it is not, some
coarse adjustments of the two black nylon finder scope align-
ment thumb screws will be needed to get the finder scope
roughly parallel to the main tube.
Note:The image in both the finder scope and the main tele-
scope will appear upside-down (rotated 180°).This is normal
for finder scopes and reflector telescopes (see Figure 4).
By loosening or tightening the alignment thumb screws,
you change the line of sight of the finder scope. Continue
making adjustments to the alignment thumb screws until
the image in both the finder scope and the telescope’s eye-
piece is exactly centered. Check the alignment by moving
the telescope to another object and fixing the finder scope’s
crosshairs on the exact point you want to look at.Then look
through the telescope’s eyepiece to see if that point is cen-
tered in the field of view. If it is, the job is done.If not, make
the necessary adjustments until the two images match up.
The finder scope alignment needs to be checked before
every observing session.This can easily be done at night,
before viewing through the telescope. Choose any bright
star or planet, center the object in the telescope eyepiece,
and then adjust the finder scope’s alignment screws until
the star or planet is also centered on the finder’s
crosshairs.The finder scope is an invaluable tool for locat-
ing objects in the night sky; its usage for this purpose will
be discussed later, in detail.
When transporting the telescope, we recommend removing
the finder scope and bracket from the tube.This is done by
Naked-eye view
View through finder scope and telescope
Figure 4. The view through a standard finder scope and reflector
telescope is upside down.This is true for the SpaceProbe 130mm
and its finder scope as well.

7
simply loosening the thumb screw on the dovetail slot.
Store the finder scope and bracket in an appropriate eye-
piece/accessory case.
Focusing the Finder Scope
If, when looking through the finder scope, the images appear
somewhat out of focus, you will need to refocus the finder
scope for your eyes.Loosen the lock ring located behind the
objective lens cell on the body of the finder scope (see Figure
5). Back the lock ring off by a few turns, for now. Refocus the
finder scope on a distant object by threading the objective
lens cell in or out on the finder scope body. Precise focusing
will be achieved by focusing the finder scope on a bright star.
Once the image appears sharp, retighten the lock ring behind
the objective lens cell.The finder scope’s focus should not
need to be adjusted again.
5. Setting Up and Using the
Equatorial Mount
When you look at the night sky, you no doubt have noticed
that the stars appear to move slowly from east to west over
time.That apparent motion is caused by the Earth’s rotation
(from west to east). An equatorial mount (Figure 2) is
designed to compensate for that motion, allowing you to eas-
ily “track” the movement of astronomical objects, thereby
keeping them from drifting out of the telescope’s field of view
while you’re observing.
Thisisaccomplishedbyslowlyrotatingthetelescopeonitsright ascen-
sion(R.A.)axis,usingonlytheR.A.slow-motioncable.But first the R.A.
axisofthemountmustbealignedwiththeEarth’srotational(polar)axis
—aprocesscalledpolaralignment.
Polar Alignment
For Northern Hemisphere observers, approximate polar
alignment is achieved by pointing the mount’s R.A.axis at the
North Star, or Polaris. It lies within 1° of the north celestial
pole (NCP), which is an extension of the Earth’s rotational
axis out into space.Stars in the Northern Hemisphere appear
to revolve around the NCP.
To find Polaris in the sky, look north and locate the pattern of
the Big Dipper (Figure 6). The two stars at the end of the
“bowl” of the Big Dipper point right to Polaris.
Observers in the Southern Hemisphere aren’t so fortunate to
have a bright star so near the south celestial pole (SCP).The
star Sigma Octantis lies about 1° from the SCP, but it is bare-
ly visible with the naked eye (magnitude 5.5).
For general visual observation, an approximate polar align-
ment is sufficient.
1. Level the equatorial mount by adjusting the length of the
three tripod legs.
2. Loosen the latitude lock t-bolt.Turn the latitude adjustment
t-bolt and tilt the mount until the pointer on the latitude
scale is set at the latitude of your observing site. If you
don't know your latitude, consult a geographical atlas to
find it. For example, if your latitude is 35° North, set the
pointer to 35.Then retighten the latitude lock t-bolt.The
latitude setting should not have to be adjusted again
unless you move to a different viewing location some dis-
tance away.
3. Loosen the Dec. lock knob and rotate the telescope optical
tube until it is parallel with the R.A.axis, as it is in Figure
1.The pointer on the Dec. setting circle should read 90°.
Retighten the Dec. lock lever.
4. Loosen the azimuth lock knob at the base of the equatorial
mount and rotate the mount so the telescope tube (and
R.A. axis) points roughly at Polaris. If you cannot see
Polaris directly from your observing site, consult a com-
Figure 6. To find Polaris in the night sky,
look north and find the Big Dipper. Extend
an imaginary line from the two “Pointer
Stars” in the bowl of the Big Dipper. Go
about five times the distance between those
stars and you’ll reach Polaris, which lies
within 1° of the north celestial pole (NCP).
Big Dipper
(in Ursa Major)
Little Dipper
(in Ursa Minor)
N.C.P.
Pointer Stars
Polaris
Cassiopeia
Focus
lock ring
Figure 5. The 6x30 finder scope and bracket.
Objective lens Alignment
thumb screws
Spring-loaded
tensioner Eyepiece

8
pass and rotate the mount so the telescope points North.
Retighten the azimuth lock knob.
The equatorial mount is now polar aligned for casual observ-
ing. More precise polar alignment is recommended for
astrophotography.
From this point on in your observing session, you should not
make any further adjustments in the azimuth or the latitude
of the mount, nor should you move the tripod. Doing so will
undo the polar alignment.The telescope should be moved
only about its R.A. and Dec. axes.
Use of the R.A. and Dec. Slow-Motion Control Cables
The R.A. and Dec. slow-motion control cables allow fine
adjustment of the telescope’s position to center objects with-
in the field of view.Before you can use the cables, you must
manually “slew” the mount to point the telescope in the vicini-
ty of the desired target. Do this by loosening the R.A. and
Dec. lock knobs and moving the telescope about the mount's
R.A. and Dec. axes. Once the telescope is pointed some-
where close to the object to be viewed, retighten the mount's
R.A. and Dec. lock knobs.
The object should now be visible somewhere in the tele-
scope's finder scope.If it isn’t, use the slow-motion controls to
scan the surrounding area of sky.When the object is visible in
the finder scope, use the slow-motion controls to center it.
Now, look in the telescope with a long focal length (low mag-
nification) eyepiece.If the finder scope is properly aligned, the
object should be visible somewhere in the field of view.
Once the object is visible in the telescope’s eyepiece, use the
slow-motion controls to center it in the field of view.You can
now switch to a higher magnification eyepiece, if you wish.
After switching eyepieces, you can use the slow-motion con-
trol cables to re-center the image, if necessary.
The Dec. slow-motion control cable can move the telescope
a maximum of 25°. This is because the Dec. slow-motion
mechanism has a limited range of mechanical travel. (The
R.A. slow-motion mechanism has no limit to its amount of
travel.) If you can no longer rotate the Dec.control cable in a
desired direction, you have reached the end of travel, and the
slow-motion mechanism should be reset.This is done by first
rotating the control cable several turns in the opposite direc-
tion from which it was originally being turned.Then, manually
slew the telescope closer to the object you wish to observe
(remember to first loosen the Dec.lock knob).You should now
be able to use the Dec. slow-motion control cable again to
fine adjust the telescope’s position.
Tracking Celestial Objects
When you observe a celestial object through the telescope,
you'll see it drift slowly across the field of view.To keep it in the
field, if your equatorial mount is polar aligned, just turn the R.A.
slow-motion control cable.The Dec. slow-motion control cable
is not needed for tracking.Objects will appear to move faster
at higher magnifications, because the field of view is narrower.
Optional Motor Drives for Automatic Tracking
An optional DC motor drive can be mounted on the R.A.axis
of the equatorial mount to provide hands-free tracking.
Objects will then remain stationary in the field of view without
any manual adjustment of the R.A.slow-motion control cable.
Understanding the Setting Circles
The setting circles on an equatorial mount enable you to
locate celestial objects by their “celestial coordinates”. Every
object resides in a specific location on the “celestial sphere”.
That location is denoted by two numbers: its right ascension
(R.A.) and declination (Dec.). In the same way, every location
on Earth can be described by its longitude and latitude.R.A.
is similar to longitude on Earth, and Dec. is similar to latitude.
The R.A. and Dec. values for celestial objects can be found
in any star atlas or star catalog.
The R.A. setting circle is scaled in hours, from 1 through 24,
with small hash marks in between representing 10-minute
increments (there are 60 minutes in 1 hour of R.A.).The lower
set of numbers (closest to the plastic R.A.gear cover) apply
to viewing in the Northern Hemisphere, while the numbers
above them apply to viewing in the Southern Hemisphere.
The Dec. setting circle is scaled in degrees, with each hash
mark representing 1° increments.Values of Dec. coordinates
range from +90° to -90°.For Northern Hemisphere observers,
use the numbers on the setting circle that are closest to the
eastern horizon.The 0° mark indicates the celestial equator;
values north of the Dec. = 0° mark are positive, while values
south of the Dec. = 0° mark are negative.
So, the coordinates for the Orion Nebula listed in a star atlas
will look like this:
R.A. 5h 35.4m Dec. -5° 27'
That’s 5 hours and 35.4 minutes in right ascension, and -5
degrees and 27 arc-minutes in declination (there are 60 arc-
minutes in 1 degree of declination).
Before you can use the setting circles to locate objects, the
mount must be well polar aligned, and the R.A.setting circle
must be calibrated.The Dec. setting circle has been perma-
nently calibrated at the factory, and should read 90° whenever
the telescope optical tube is parallel with the R.A.axis.
Calibrating the Right Ascension Setting Circle
1. Identify a bright star near the celestial equator (Dec. = 0°)
and look up its coordinates in a star atlas.
2. Loosen the R.A. and Dec. lock knobs on the equatorial
mount, so the telescope optical tube can move freely.
3. Point the telescope at the bright star near the celestial
equator whose coordinates you know. Lock the R.A. and
Dec. lock knobs.Center the star in the telescope’s field of
view with the slow-motion control cables.
4.Loosen the R.A.setting circle lock thumb screw located just
above the R.A.setting circle pointer; this will allow the set-
ting circle to rotate freely. Rotate the setting circle until the
pointer indicates the R.A.coordinate listed in the star atlas
for the object. Retighten the thumb screw.

Finding Objects With the Setting Circles
Now that both setting circles are calibrated, look up in a star
atlas the coordinates of an object you wish to view.
1. Loosen the Dec. lock knob and rotate the telescope until
the Dec. value from the star atlas matches the reading on
the Dec. setting circle. Remember to use the +90° to -90°
scale that is on the eastern half of the Dec. setting circle.
Retighten the Dec. lock knob.
2. Loosen the R.A. lock knob and rotate the telescope until
the R.A. value from the star atlas matches the reading on
the R.A. setting circle. Retighten the lock knob.
Most setting circles are not accurate enough to put an object
dead-center in the telescope’s eyepiece, but they should
place the object somewhere within the field of view of the
finder scope, assuming the equatorial mount is accurately
polar aligned. Use the slow-motion controls to center the
object in the finder scope, and it should appear in the tele-
scope’s field of view.
The R.A. setting circle must be re-calibrated every time you
wish to locate a new object.Do so by calibrating the setting
circle for the centered object before moving on to the next one.
Confused About Pointing the Telescope?
Beginners occasionally experience some confusion about
how to point the telescope overhead or in other directions.In
Figure 1 the telescope is pointed north, as it would be during
polar alignment.The counterweight shaft is oriented down-
ward.But it will not look like that when the telescope is pointed
in other directions.Let's say you want to view an object that is
directly overhead, at the zenith.How do you do it?
9
b. d.
Figure 7a, 7b, 7c, 7d: This illustration shows the telescope pointed in the four cardinal directions: (a) north, (b) south, (c) east, (d)
west. Note that the tripod and mount have not been moved; only the telescope tube has been moved on the R.A.and Dec. axes.
a. c.

10
One thing you DO NOT do is make any adjustment to the lat-
itude adjustment t-bolt. That will nullify the mount’s polar
alignment. Remember, once the mount is polar aligned, the
telescope should be moved only on the R.A.and Dec. axes.
To point the scope overhead, first loosen the R.A. lock knob
and rotate the telescope on the R.A. axis until the counter-
weight shaft is horizontal (parallel to the ground).Then loosen
the Dec. lock knob and rotate the telescope until it is pointing
straight overhead.The counterweight shaft is still horizontal.
Then retighten both lock knobs.
Similarly, to point the telescope directly south, the counter-
weight shaft should again be horizontal.Then you simply rotate
the scope on the Dec.axis until it points in the south direction.
What if you need to aim the telescope directly north, but at
an object that is nearer to the horizon than Polaris?You can’t
do it with the counterweight down as pictured in Figure 1.
Again, you have to rotate the scope in R.A. so the counter-
weight shaft is positioned horizontally.Then rotate the scope
in Dec. so it points to where you want it near the horizon.
To point the telescope to the east or west, or in other direc-
tions, you rotate the telescope on its R.A. and Dec. axes.
Depending on the altitude of the object you want to observe,
the counterweight shaft will be oriented somewhere between
vertical and horizontal.
Figure 7 illustrates how the telescope will look pointed at the
four cardinal directions — north, south, east, and west
The key things to remember when pointing the telescope is that
a) you only move it in R.A.and Dec., not in azimuth or latitude
(altitude), and b) the counterweight and shaft will not always
appear as it does in Figure 1.In fact, it almost never will!
6. Collimating the Optics
(Aligning the Mirrors)
Collimation is the process of adjusting the mirrors so they are
precisely aligned with each other. Your telescope's optics
were aligned at the factory, and should not need much adjust-
ment unless the telescope was roughly handled during
shipment. Accurate collimation is important to insuring the
peak performance of your telescope, so it should be checked
before each observing session.Collimation is easy to do, and
should be done in daylight.
To check the collimation, remove the eyepiece and look down
the focuser drawtube.You should see the secondary mirror
centered under the drawtube, the reflection of the primary
mirror centered in the secondary mirror, and the reflection of
the secondary mirror (and your eye) centered in the reflec-
tion of the primary mirror, as in Figure 8a. If anything is
off-center, follow the collimation procedure below.
It helps to put a piece of white paper on the inside of the opti-
cal tube opposite the focuser.The white paper forms a bright
Figure 8. Collimating the optics. (a) When the mirrors are properly aligned, the view down the focuser drawtube should look like this. (b) If
the optics are out of alignment, the view might look something like this.(c) Here, the secondary mirror is centered under the focuser, but it
needs to be adjusted (tilted) so that the entire primary mirror is visible. (d) The secondary mirror is correctly aligned, but the primary mirror
still needs adjustment.When the primary mirror is correctly aligned, the eye will be centered, as in (a).
a.
b. c.
d.

background behind the secondary mirror, making it easier to
distinguish the mirror holder from the background.
Use a Collimation Tool
To aid in centering your line of sight down the focuser draw-
tube, and in centering the mirror reflections during
collimation, it is very helpful to use a precision collimating tool
containing crosshairs, such as the Orion Collimating
Eyepiece (#3640). A laser collimator, like the Orion
LaserMate (#5680), can also be employed to obtain very
accurate optical alignment.We highly recommend that you
purchase one of these devices in order to get the best per-
formance out of your telescope.
Aligning the Secondary Mirror
With the eyepiece removed, look straight down the open
focuser drawtube at the secondary mirror. Ignore the reflec-
tions for the time being. The secondary mirror should be
centered in the field of view.If it isn’t, as in Figure 8b, it must
be adjusted. (It helps to adjust the secondary mirror in a
brightly lit room with the telescope pointed toward a bright
surface, such as white paper or a wall.)
If the secondary mirror is not centered in the focuser draw-
tube (in the direction parallel to the length of the telescope),
loosen the three set screws in the center hub of the sec-
ondary mirror holder several turns.You will need a 2mm Allen
wrench to do this. Now grasp the secondary mirror holder
with your fingers (be careful not to touch the surface of the
secondary mirror) and keep it stationary while turning the
central Phillips head screw (as in Figure 9).Turning the bolt
clockwise will move the secondary mirror toward the front
opening of the optical tube, while turning the bolt counter-
clockwise will move the secondary mirror toward the primary
mirror.When the secondary mirror is centered in the focuser
drawtube (as in Figure 8c), rotate the secondary mirror hold-
er slightly side-to-side until the reflection of the primary mirror
is as centered in the secondary mirror as it will get.It still may
not be perfectly centered yet, but that is OK.Now tighten the
three set screws to secure the secondary mirror in that posi-
tion.This adjustment will rarely need to be done, if ever.
If the entire primary mirror reflection is not visible in the sec-
ondary mirror (as it is not in Figure 8c), adjust the tilt of the
secondary mirror by alternately loosening one of the three set
screws a turn and tightening the other two (Figure 10).The
goal is to center the primary mirror reflection in the secondary
mirror, as depicted in Figure 8d. Don’t worry if the reflection
of the secondary mirror (the smallest circle, with your eye
reflected in it) is off-center (as is the case in Figure 8d); you
will fix that in the next step.
Adjusting the Primary Mirror
The final adjustment is made to the primary mirror.It will need
adjustment if, as in Figure 8d, the secondary mirror is cen-
tered under the focuser and the reflection of the primary mirror
is centered in the secondary mirror, but the small reflection of
the secondary mirror (with your eye inside) is off-center.
To access the primary mirror collimation screws, remove the
cover plate on the rear end of the optical tube (bottom of the
primary mirror cell) by unthreading the three Phillips head
screws with a screwdriver.The tilt of the primary is adjusted
with the three pairs of collimation screws (see Figure 11).The
collimation screws can be turned with a Phillips head screw-
driver and a 2.5mm Allen wrench.
11
Figure 9: To center the secondary mirror under the focuser, hold the
secondary mirror holder in place with one hand while adjusting the cen-
ter screw with a Phillips screwdriver.Do not touch the mirror's surface
Figure 10: Adjust the tilt of the secondary mirror by loosening or
tightening the three alignment set screws with a 2mm Allen wrench.
Figure 11: The back end of the optical tube (bottom of the primary
mirror cell).The three pairs of set screws and Phillips-head screws
adjust the tilt of the primary mirror.
Phillips-head screw
Set screw

12
Each pair of collimation screws work together to adjust the
tilt.The set screw pushes the mirror cell forward, while the
Phillips head screw pulls the mirror cell back. One must be
loosened and the other tightened by the same amount in
order to adjust the tilt. Try tightening and loosening one of the
pairs of collimation screws one turn.Look into the focuser and
see if the secondary mirror reflection has moved closer to the
center of the primary mirror reflection. Repeat this process
on the other two pairs of collimation screws, if necessary. It
will take a little trial and error to get a feel for how to tilt the
mirror in this way to center the reflection. It helps to have two
people for primary mirror collimation; one to look in the
focuser while the other adjusts the collimation screws.
The view down the focuser should now resemble Figure 8a.
The secondary mirror is centered under the focuser; the
reflection of the primary mirror is centered in the secondary
mirror, and the reflection of the secondary mirror is centered
in the reflection of the primary mirror.
A simple star test will tell you whether the optics are accu-
rately collimated.
Star Testing Your Telescope
When it is dark, point the telescope at a bright star and center it
in the eyepiece’s field of view with the R.A.and Dec.slow-motion
controls. Slowly rack the image out of focus with the focusing
knob.If the telescope is correctly collimated, the expanding disk
should be a circle.If it is unsymmetrical, the scope is out of colli-
mation.The dark shadow cast by the secondary mirror should
appear in the very center of the out-of-focus circle, like the hole
in a doughnut.If the “hole” appears off-center, the telescope is
out of collimation (Figure 12).
If you try the star test and the bright star you have selected is
not accurately centered in the eyepiece, then the optics will
always appear out of collimation, even though they may be
perfectly aligned.It is critical to keep the star centered, so over
time you will need to make slight corrections to the telescope's
position in order to account for the sky’s apparent motion.
7. Using Your Telescope —
Astronomical Observing
Choosing an Observing Site
When selecting a location for observing, get as far away as
possible from direct artificial light such as street lights, porch
lights, and automobile headlights.The glare from these lights
will greatly impair your dark-adapted night vision. Set up on a
grass or dirt surface, not asphalt, because asphalt radiates
more heat. Heat disturbs the surrounding air and degrades
the images seen through the telescope.Avoid viewing over
rooftops and chimneys, as they often have warm air currents
rising from them. Similarly, avoid observing from indoors
through an open (or closed) window, because the tempera-
ture difference between the indoor and outdoor air will cause
image blurring and distortion.
If at all possible, escape the light-polluted city sky and head
for darker country skies.You’ll be amazed at how many more
stars and deep-sky objects are visible in a dark sky!
“Seeing” and Transparency
Atmospheric conditions vary significantly from night to night.
“Seeing” refers to the steadiness of the Earth’s atmosphere
at a given time.In conditions of poor seeing, atmospheric tur-
bulence causes objects viewed through the telescope to
“boil”. If, when you look up at the sky with just your eyes, the
stars are twinkling noticeably, the seeing is bad and you will
be limited to viewing with low powers (bad seeing affects
images at high powers more severely).Planetary observing
may also be poor.
In conditions of good seeing, star twinkling is minimal and
images appear steady in the eyepiece. Seeing is best over-
head, worst at the horizon.Also, seeing generally gets better
after midnight, when much of the heat absorbed by the Earth
during the day has radiated off into space.
Especially important for observing faint objects is good“trans-
parency”— air free of moisture, smoke, and dust. All tend to
scatter light, which reduces an object’s brightness.Transparency
is judged by the magnitude of the faintest stars you can see with
the unaided eye (6th magnitude or fainter is desirable).
Cooling the Telescope
All optical instruments need time to reach “thermal equilibri-
um”.The bigger the instrument and the larger the temperature
change, the more time is needed.Allow at least 30 minutes
for your telescope to cool to the temperature outdoors.In very
cold climates (below freezing), it is essential to store the tele-
scope as cold as possible. If it has to adjust to more than a
40° temperature change, allow at least one hour.
Let Your Eyes Dark-Adapt
Don't expect to go from a lighted house into the darkness of
the outdoors at night and immediately see faint nebulas, galax-
ies, and star clusters - or even very many stars, for that matter.
Your eyes take about 30 minutes to reach perhaps 80% of their
full dark-adapted sensitivity. As your eyes become dark-adapt-
Figure 12. A star test will determine if a telescope’s optics are properly
collimated. An unfocused view of a bright star through the eyepiece
should appear as illustrated on right if optics are perfectly collimated.If
circle is unsymmetrical, as in illustration on left, scope needs collimation.
Out of collimation Collimated

ed, more stars will glimmer into view and you'll be able to see
fainter details in objects you view in your telescope.
To see what you’re doing in the darkness, use a red-filtered
flashlight rather than a white light. Red light does not spoil
your eyes’dark adaptation like white light does.A flashlight
with a red LED light is ideal, or you can cover the front of a
regular incandescent flashlight with red cellophane or paper.
Beware, too, that nearby porch and streetlights and car head-
lights will ruin your night vision.
Eyepiece Selection
By using eyepieces of varying focal lengths, it is possible to
attain many magnifications with the SpaceProbe 130ST EQ.
The telescope comes with two high-quality Explorer II eye-
pieces: a 25mm, which gives a magnification of 26x, and a
10mm, which gives a magnification of 65x.Other eyepieces
can be used to achieve higher or lower powers. It is quite
common for an observer to own five or more eyepieces to
access a wide range of magnifications. This allows the
observer to choose the best eyepiece to use depending on
the object being viewed.
To calculate the magnification, or power, of a telescope and
eyepiece combination, simply divide the focal length of the
telescope by the focal length of the eyepiece:
For example, the SpaceProbe 130ST EQ, which has a focal
length of 650mm, used in combination with the 25mm eye-
piece, yields a power of
650 ∏25 = 26x
Every telescope has a useful limit of power of about 45x-60x
per inch of aperture. Claims of higher power by some tele-
scope manufacturers are a misleading advertising gimmick
and should be dismissed. Keep in mind that at higher pow-
ers, an image will always be dimmer and less sharp (this is a
fundamental law of optics). The steadiness of the air (the
“seeing”) will also limit how much magnification an image can
tolerate.
Whatever you choose to view, always start by inserting your
lowest-power (longest focal length) eyepiece to locate and
center the object. Low magnification yields a wide field of
view, which shows a larger area of sky in the eyepiece.This
makes acquiring and centering an object much easier. If you
try to find and center objects with high power (narrow field of
view), it’s like trying to find a needle in a haystack!
Once you've centered the object in the eyepiece, you can
switch to higher magnification (shorter focal length eyepiece),
if you wish. This is especially recommended for small and
bright objects, like planets and double stars.The Moon also
takes higher magnifications well.
Deep-sky objects, however, typically look better at medium or
low magnifications.This is because many of them are quite
faint, yet have some extent (apparent width). Deep-sky
objects will often disappear at higher magnifications, since
greater magnification inherently yields dimmer images.This
is not the case for all deep-sky objects, however. Many galax-
ies are quite small, yet are somewhat bright, so higher power
may show more detail.
The best rule of thumb with eyepiece selection is to start with
a low power, wide field, and then work your way up in magni-
fication. If the object looks better, try an even higher
magnification. If the object looks worse, then back off the
magnification a little by using a lower-power eyepiece.
Objects to Observe
Now that you are all set up and ready to go, one critical deci-
sion must be made: what to look at?
A. The Moon
With its rocky surface, the Moon is one of the easiest and most
interesting targets to view with your telescope.Lunar craters,
marias, and even mountain ranges can all be clearly seen
from a distance of 238,000 miles away! With its ever-chang-
ing phases, you’ll get a new view of the Moon every night.The
best time to observe our one and only natural satellite is dur-
ing a partial phase, that is, when the Moon is NOT full. During
partial phases, shadows are cast on the surface, which reveal
more detail, especially right along the border between the dark
and light portions of the disk (called the “terminator”). A full
Moon is too bright and devoid of surface shadows to yield a
pleasing view.Make sure to observe the Moon when it is well
above the horizon to get the sharpest images.
Use an optional Moon filter to dim the Moon when it is very
bright. It simply threads onto the bottom of the eyepieces (you
must first remove the eyepiece from the focuser to attach a fil-
ter).You'll find that the Moon filter improves viewing comfort,
and also helps to bring out subtle features on the lunar surface.
B. The Sun
You can change your nighttime telescope into a daytime Sun
viewer by installing an optional full-aperture solar filter over
the front opening of the SpaceProbe 130ST EQ.The primary
attraction is sunspots, which change shape, appearance, and
location daily. Sunspots are directly related to magnetic activ-
ity in the Sun. Many observers like to make drawings of
sunspots to monitor how the Sun is changing from day to day.
Important Note: Do not look at the Sun with any optical
instrument without a professionally made solar filter, or
permanent eye damage could result.
C. The Planets
The planets don’t stay put like the stars, so to find them you
should refer to Sky Calendar at our website
(www.telescope.com), or to charts published monthly in
Astronomy, Sky & Telescope, or other astronomy magazines.
Venus, Mars, Jupiter, and Saturn are the brightest objects in the
sky after the Sun and the Moon.Your SpaceProbe 130ST EQ is
capable of showing you these planets in some detail.Other plan-
ets may be visible but will likely appear star-like.Because planets
are quite small in apparent size, optional higher-power eyepieces
are recommended and often needed for detailed observations.
Not all the planets are generally visible at any one time.
JUPITER The largest planet, Jupiter, is a great subject for
observation. You can see the disk of the giant planet and
watch the ever-changing positions of its four largest moons—
13

Io, Callisto, Europa, and Ganymede.Higher-power eyepieces
should bring out the cloud bands on the planet's disk.
SATURN The ringed planet is a breathtaking sight when it is
well positioned.The tilt angle of the rings varies over a peri-
od of many years; sometimes they are seen edge-on, while
at other times they are broadside and look like giant “ears” on
each side of Saturn’s disk.A steady atmosphere (good see-
ing) is necessary for a good view. You will probably see a
bright “star” close by, which is Saturn’s brightest moon, Titan.
VENUS At its brightest, Venus is the most luminous object in
the sky, excluding the Sun and the Moon.It is so bright that
sometimes it is visible to the naked eye during full daylight!
Ironically, Venus appears as a thin crescent, not a full disk,
when at its peak brightness.Because it is so close to the Sun,
it never wanders too far from the morning or evening horizon.
No surface markings can be seen on Venus, which is always
shrouded in dense clouds.
MARS The Red Planet makes its closest approach to Earth
every two years. During close approaches you’ll see a red
disk, and may be able to see the polar ice cap.To see surface
detail on Mars, you will need a high-power eyepiece and very
steady air!
D.The Stars
Stars will appear like twinkling points of light.Even powerful
telescopes cannot magnify stars to appear as more than a
point of light.You can, however, enjoy the different colors of
the stars and locate many pretty double and multiple stars.
The famous “Double-Double” in the constellation Lyra and the
gorgeous two-color double star Albireo in Cygnus are
favorites.Defocusing a star slightly can help bring out its color.
E. Deep-Sky Objects
Under dark skies, you can observe a wealth of fascinating
deep-sky objects, including gaseous nebulas, open and glob-
ular star clusters, and a variety of different types of galaxies.
Most deep-sky objects are very faint, so it is important that
you find an observing site well away from light pollution.Take
plenty of time to let your eyes adjust to the darkness. Do not
expect these subjects to appear like the photographs you see
in books and magazines; most will look like dim gray
smudges.Our eyes are not sensitive enough to see color in
deep-sky objects except in a few of the brightest ones.But as
you become more experienced and your observing skills get
sharper, you will be able to ferret out more and more subtle
details and structure.
How to Find Deep-Sky Objects: Star Hopping
Star hopping, as it is called by astronomers, is perhaps the
simplest way to hunt down deep-sky objects to view in the
night sky. It entails first pointing the telescope at a bright star
close to the object you wish to observe, and then progress-
ing to other stars closer and closer to the object until it is in
the field of view of the eyepiece.It is a very intuitive technique
that has been employed for hundreds of years by profession-
al and amateur astronomers alike.Keep in mind, as with any
new task, that star hopping may seem challenging at first, but
will become easier over time and with practice.
To star hop, only a minimal amount of additional equipment is
necessary.A star chart or atlas that shows stars to at least mag-
nitude 5 is required.Select one that shows the positions of many
deep-sky objects, so you will have a lot of options to choose
from.If you do not know the positions of the constellations in the
night sky, you will need a planisphere to identify them.
Start by choosing bright objects to view.The brightness of an
object is measured by its visual magnitude; the brighter an
object, the lower its magnitude.Choose an object with a visu-
al magnitude of 9 or lower. Many beginners start with the
Messier objects, which represent some of the best and bright-
est deep-sky objects, first catalogued about 200 years ago
by the French astronomer Charles Messier.
Determine in which constellation the object lies. Now, find the
constellation in the sky. If you do not recognize the constella-
tions on sight, consult a planisphere.The planisphere gives
an all-sky view and shows which constellations are visible on
a given night at a given time.
Now, look at your star chart and find the brightest star in the
constellation that is near the object you are trying to find.
Using the finder scope, point the telescope at this star and
center it on the crosshairs.Next, look again at the star chart
and find another suitably bright star near the bright star cur-
rently centered in the finder. Keep in mind that the field of
view of the finder scope is about 6°, so you should choose
another star that is no more that 6° from the first star, if pos-
sible. Move the telescope slightly, until the telescope is
centered on the new star.
Continue using stars as guideposts in this way until you are
at the approximate position of the object you are trying to find
14
Figure 13. Star hopping is a good way to locate hard-to-find objects.
Refer to a star chart to map a route to the object that uses bright stars
as guideposts. Center the first star you’ve chosen in the finder scope
and telescope eyepiece (1). Now move the scope carefully in the
direction of the next bright star (2), until it is centered. Repeat (3 and
4).The last hop (5) should place the desired object in the eyepiece.

15
(Figure 13). Look in the telescope’s eyepiece, and the object
should be somewhere within the field of view.If it's not, sweep
the telescope carefully around the immediate vicinity until the
object is found.
If you have trouble finding the object, start the star hop again
from the brightest star near the object you wish to view.This
time, be sure the stars indicated on the star chart are in fact
the stars you are centering in the eyepiece. Remember, the
finder scope (and main telescope eyepiece, for that matter)
gives an inverted image, so you must keep this in mind when
star hopping from star to star.
8. Care and Maintenance
If you give your telescope reasonable care, it will last a life-
time.Store it in a clean, dry, dust-free place, safe from rapid
changes in temperature and humidity. Do not store the tele-
scope outdoors, although storage in a garage or shed is OK.
Small components like eyepieces and other accessories
should be kept in a protective box or storage case. Keep the
caps on the front of the telescope and on the focuser draw-
tube when it is not in use.
Your SpaceProbe 130ST EQ telescope requires very little
mechanical maintenance.The optical tube is steel and has a
smooth painted finish that is fairly scratch-resistant. If a
scratch does appear on the tube, it will not harm the tele-
scope.If you wish, you may apply some auto touch-up paint
to the scratch.Smudges on the tube can be wiped off with a
soft cloth and a household cleaner such as Windex or
Formula 409.
Cleaning Lenses
Any quality optical lens cleaning tissue and optical lens clean-
ing fluid specifically designed for multi-coated optics can be
used to clean the exposed lenses of your eyepieces or finder
scope. Never use regular glass cleaner or cleaning fluid
designed for eyeglasses. Before cleaning with fluid and tissue,
however, blow any loose particles off the lens with a blower
bulb or compressed air.Then apply some cleaning fluid to a tis-
sue, never directly on the optics. Wipe the lens gently in a
circular motion, then remove any excess fluid with a fresh lens
tissue.Oily fingerprints and smudges may be removed using
this method. Use caution; rubbing too hard may scratch the
lens.On larger lenses, clean only a small area at a time, using
a fresh lens tissue on each area.Never reuse tissues.
Cleaning Mirrors
You should not have to clean your telescope’s mirrors very
often; normally once every year or so. Covering your tele-
scope when it is not in use will prevent dust from
accumulating on the mirrors.Improper cleaning can scratch
mirror coatings, so the fewer times you have to clean the mir-
rors, the better. Small specks of dust or flecks of paint have
virtually no effect on the visual performance of the telescope.
The large primary mirror and the elliptical secondary mirror of
your telescope are front-surface aluminized and over-coated
with hard silicon monoxide, which prevents the aluminum from
oxidizing.These coatings normally last through many, many
years of use before requiring re-coating (which is easily done).
To clean the secondary mirror, remove the mirror in its holder
from the 4-vaned spider in the tube.Do this by grasping the
secondary mirror holder with your fingertips while turning the
central bolt on the spider’s central hub counterclockwise.
Handle the mirror holder only; do not touch the mirror surface.
Then follow the same procedure described below for cleaning
the primary mirror.The secondary mirror is glued into its hold-
er, and should not be removed from the holder for cleaning.
To clean the primary mirror, carefully remove the mirror cell
from the telescope.Do this by first removing the four screws
that connect the mirror cell to the tube. These screws are
located on the outside of the tube, just above the mirror cell
casting. Next, remove the primary mirror from the mirror cell;
you will need to remove the three mirror clips to do this.
Completely unthread the two Phillips head screws in each
clip, and carefully lift the mirror from its cell.Be careful not to
touch the front surface of the mirror with your fingers.Set the
mirror with the aluminized face up on a clean, soft towel. Fill
a clean sink, free of abrasive cleanser, with room-tempera-
ture water, a few drops of liquid dishwashing detergent, and
if possible, a cap-full of rubbing alcohol. Submerge the mirror
(aluminized face up) in the water and let it soak for several
minutes (or hours if it’s a very dirty mirror).Wipe the mirror
under water with clean cotton balls, using extremely light
pressure and stroking in straight lines across the surface.Use
one ball for each wipe across the mirror.Then rinse the mir-
ror under a stream of lukewarm water. Any particles on the
surface can be swabbed gently with a series of clean cotton
balls, each used just one time. Dry the mirror in a stream of
air (a “blower bulb” works great), or remove any stray drops
of water with the corner of a paper towel.Water will run off a
clean surface.Cover the mirror surface with tissue, and leave
the entire assembly in a warm area until it is completely dry
before reassembling the telescope.
Figure 14. Remove the three
collimation screws indicated
to remove the mirror cell from
the tube.

One-Year Limited Warranty
This Orion SpaceProbe 130mm Equatorial Reflector is warranted against defects in materials
or workmanship for a period of one year from the date of purchase.This warranty is for the
benefit of the original retail purchaser only. During this warranty period Orion Telescopes &
Binoculars will repair or replace, at Orion’s option, any warranted instrument that proves to be
defective, provided it is returned postage paid to: Orion Warranty Repair, 89 Hangar Way,
Watsonville, CA 95076.If the product is not registered, proof of purchase (such as a copy of
the original invoice) is required.
This warranty does not apply if, in Orion’s judgment, the instrument has been abused, mis-
handled, or modified, nor does it apply to normal wear and tear. This warranty gives you
specific legal rights, and you may also have other rights, which vary from state to state. For
further warranty service information, contact: Customer Service Department, Orion
Telescopes & Binoculars, P. O. Box 1815, Santa Cruz, CA 95061; [phone].
9. Specifications
Optical tube: Steel
Primary mirror diameter: 130mm
Primary mirror coating: Aluminum with silicon monoxide (SiO) overcoat
Primary mirror figure: Parabolic
Secondary mirror minor axis: 37mm
Focal length: 650mm
Focal ratio: f/5
Focuser: Rack and pinion, accepts 1.25" eyepieces
Eyepieces:25mm and 10mm Explorer II, fully coated, 1.25"
Magnification: 26x (with 25mm), 65x (with 10mm)
Finder scope: 6x magnification, 30mm aperture, achromatic, crosshairs
Mount: German-type equatorial
Tripod: Aluminum
Motor drives: Optional
Weight: 28.4 lbs (tube 6.9 lbs, mount 21.5 lbs)
1-year Limited Warranty
Orion Telescopes & Binoculars
Post Office Box 1815, Santa Cruz, CA 95061
Customer Support Help Line [phone] • Day or Evening