Orion OE392-10-GPCXP Quick start guide

System Manager TS II
For GPC-XP
Technical Guide
GPC-XP Controller Code: YS102432 Revision 4.0 and up

Zone
Zone
TABLE OF CONTENTS
OVERVIEW........................................................................................................................................................ 3
COMPONENTS AND WIRING............................................................................................................................ 4
Flush Wall Mount Dimensions and Components .........................................................................................................................5
Surface Mount Dimensions and Components..............................................................................................................................6
SMTS II to GPC-XP Controller Wiring..........................................................................................................................................7
NAVIGATION .................................................................................................................................................... 8
Main Screen Icons and Button Functions.....................................................................................................................................8
MAIN SCREEN FUNCTIONS ............................................................................................................................. 9
Logging In.....................................................................................................................................................................................9
Editing Passcodes......................................................................................................................................................................10
Setting The System Clock..........................................................................................................................................................11
System Manager Settings..........................................................................................................................................................12
Unit Selection.............................................................................................................................................................................13
GPC-XP CONTROLLER SCREENS .................................................................................................................. 13
Status & Configuration Screens.................................................................................................................................................13
SCHEDULES & HOLIDAYS.............................................................................................................................. 16
Viewing and Setting Schedules .................................................................................................................................................16
Viewing and Setting Holidays.....................................................................................................................................................17
Schedule Override......................................................................................................................................................................18
ALARMS.......................................................................................................................................................... 18
Viewing & Enabling/DisablingAlarms ........................................................................................................................................18
APPENDIX ...................................................................................................................................................... 19
Troubleshooting - System Manager TS II LEDs, Buttons, Dipswitches, and Jumpers...............................................................19
Military Time Conversion............................................................................................................................................................20
INDEX............................................................................................................................................................. 21
WattMaster Controls Inc.
8500 NW River Park Drive · Parkville, MO 64152
Toll Free Phone: [phone]
PH: [phone] · FAX: [phone]
E-mail: [e-mail]
Visit our web site at www.orioncontrols.com
Form: OR-SMTSII-GPCXP-TGD-01A
Copyright May 2014 WattMaster Controls, Inc.
AAON®is a registered trademark of AAON, Inc., Tulsa, OK.
WattMaster Controls, Inc. assumes no responsibility for errors or omissions.
This document is subject to change without notice.
www.orioncontrols.com

SMTS II for GPC-XP Technical Guide
OVERVIEW
3
Features
The OE392-10-GPCXP System Manager TS II (Touch Screen) for
the GPC-XPController provides a direct, graphic-enhanced, menu-
driven link to enable you to view the status, perform force modes,
and set schedules for your GPC-XP Controller. (See Figure 1.)
The System Manager TS II provides the following useful functions:
• Provides a 4.3” 480 x 272 WQVGARGB TFT LCD
Graphical Touch Screen LCD display with 16 million
colors
• Utilizes a graphical touch screen menu system with easy-
to-understand menu trees and icons and non-cryptic, plain
English language messages
• Makes entering data quick and easy with instructions on
each screen
• Graphic status screens provide easy monitoring of the
GPC-XP without specialized training
• Provides protection from unauthorized users through inte-
gral multi-level passcode authorization programming
• Comes equipped with real-time clock backup power supply
for short power losses
• Provides icons to indicate alarm conditions
• LEDs behind plastic panel indicate power, communica-
tions, and operation
• Plastic enclosure allows for easy flush wall mounting in
hollow drywall or surface mounting on solid wall surface
System Manager TS II
System Requirements
• The System Manager TS II is packaged and assembled for
flush wall mounting. Surface mount components are also
included for your convenience.
• If using the surface mount version, you will need a double
duplex outlet box (by others).
• The System Manager TS II for GPC-XP only
communicates with the GPC-XP Controller
NOTE: Initial programming of the GPC-XP must first be
done with a personal computer using our Prism 2
software. The Prism 2 software can be downloaded
from our website—orioncontrols.com. See the
GPC-XP Controller Technical Guide for detailed
instructions. The GPC-XP contains an on-board
CommLink, allowing you to directly connect to a
computer using a USB cable.
Figure 1: System Manager TS II for the GPC-XP

COMPONENTS & WIRING
SMTS II for GPC-XP Technical Guide
4
Mounting, Wiring, Initializing, and Updating
Environmental Requirements
The System Manager TS II needs to be installed in an environment
that can maintain a temperature range between 14°F and 158°F with
less than 90% RH levels (non-condensing).
Mounting
The System Manager TS II is housed in a plastic enclosure designed
for mounting in hollow drywall construction or a control panel cover
with the flush wall mount version (shown in Figure 3,page 5) or on
a concrete, brick, or other solid wall surface with the surface mount
version (shown in Figure 4,page 6).
The flush wall mount version has integral wingnut paddles that are
tightened after installation to grip the drywall and hold the System
Manager TS II in place. For mounting in a control panel cover or
other thin material, (4) adhesive backed rubber pads are provided
to assist in securing the System Manager TS II into the cutout in
the panel. These pads are applied to the wingnut paddles to provide
a non-slip mounting against the panel’s sheet metal surface. See
Figure 2,below, for pad placement details.
The surface mount version is designed to be installed in a double
duplex outlet box (by others). Both mounting styles of the System
Manager TS II feature an integral, magnetically-secured face plate
which can be easily removed for reset of the display when required.
The System Manager TS II should be mounted at approximately eye
level to allow for ease of programming and reading of the display.
The System Manager TS II is typically mounted in the building
manager’s or superintendent’s office or in an equipment room, but
is also quite suitable for mounting in any location.
Care
The System Manager TS II should be cleaned with a soft, dust-free
cloth. Do not use any liquid to clean your System Manager TS II.
You should press the <Suspend> button located behind the cover
to temporarily freeze the touch pad before you attempt to clean
your screen. See the Troubleshooting section on page 19 for details.
Wiring
The System ManagerTS II is connected to thelocal communications
loop of the Orion system via 18AWG 2-conductor, twisted pair with
shield wire connected to the T, SHLD & R communication terminals
on the back of the System Manager TS II.The communications wire
used can beeither ourWattMaster #WR-LL-WG-18 communications
wire or Belden #82760 wire or its equivalent.
The System Manager TS II also requires that 24VAC (6 VA) power
be supplied (by others) to its + and – wiring terminal located on the
back of the System Manager TS II.
See Figure5,page 7 for wiring details. This wiring diagram depicts
wiring the System Manager TS II to the GPC-XP Controller. The
System Manager TS II can also be wired to the local loop terminals
on the MiniLink PD, Power Comm Board, or any other add-on
controller’s local loop terminals. It will still require a transformer
to be wired as shown in Figure 5, page 7.
Dipswitch and Jumper Settings
If the GPC-XP Controller is set at high speed, Dipswitch OPT1
should be set to ON. Otherwise, it should be set to OFF. As ofApril
2014, Dipswitch OPT4 should be set to ON by default. If you see
your screen is not centered correctly, switch OPT4 to the opposite
position. Dipswitches OPT2 and OPT3 should always be set to OFF.
See Figure 5,page 7 for details.
If you have a Stand-Alone system (no CommLink or MiniLink, the
TERM Jumpers must be ON. For applications with CommLink(s)
and/or MiniLink(s), the TERM Jumpers must be OFF. See Figure
5,page 7 for details.
Technical Support
Call [phone] to talk to a WattMaster Controls Technical Sup-
port Representative. Support is available Monday through Friday,
7:00 AM to 5:00 PM central standard time.
Front View (Cover Removed)
Left Side View
USE 4
Place (2) On Each Paddle Arm
As Shown When Mounting In Sheet Metal
Panel Or Other Thin Mounting Material. Pads
Are Not Required For Drywall Mounting
Rubber Pads
Rubber Pads
Figure 2: System Manager TS II - Control Panel Mounting Pad Placement Detail (Flush Wall Mount)

SMTS II for GPC-XP Technical Guide
COMPONENTS & WIRING
5
Flush Wall Mount Dimensions and Components
Figure 3: System Manager TS II Dimensions and Components (Flush Wall Mount)

COMPONENTS & WIRING
SMTS II for GPC-XP Technical Guide
6
Surface Mount Dimensions and Components
Figure 4: System Manager TS II Dimensions and Components (Surface Mount)

SMTS II for GPC-XP Technical Guide
COMPONENTS & WIRING
7
SMTS II to GPC-XP Controller Wiring
Figure 5: System Manager TS II to GPC-XP Controller Wiring
.1uF
YS102178 R4
WQVGA Graphical Interface
WattMaster Controls, Inc
C24
R9
R7
R6 R5 R2
R1
C51
C39
C20
C19
C15
C14
C13
C12 C11
C10 C9
C7
C1
X3
8.00Mhz
OFF
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002 1002 1002
1002 1002 1002 1002
1002 1002 1002 1002
1002
1002
1002 1002
1002
1002
1002
1002
1002 1002
.1uF
.1uF
.1uF
.1uF
.1uF
.1uF
.1uF
.1uF
.1uF .1uF
.1uF
.1uF
.1uF
.1uF
.1uF .1uF
.1uF .1uF
.1uF
.1uF
.1uF
.1uF
.1uF
.1uF
.1uF
.1uF .1uF
.1uF
1002
.1uF
1002
1002
.1uF
.1uF
.1uF
.1uF
LTC3824
1002
1002
1002
1002
1002
1002
66.000Mhz
MADE IN USA
330uF 50V 330uF
1002
SERIAL #
OPT4 OPT3 OPT2 OPT1
TERM
RTC
YS102178 R4
WQVGA Graphical Interface
WattMaster Controls, Inc
CAL
5V 3.3V 2.5V
J3
R34 R16
R13R8
R39
X2
R26
R17
R14
C24
U13
R49
R48
R47
R46
R45
R44
R43
R40
R37
R35
R32R31
R29
R27
R24
R22
R12
R11
R10
R9
R7
R6 R5 R2
R1
L5
L4
D12
D11
D1
C51
C50
C45
C41
C39
C36
C20
C19
C18
C17
C16
C15
C14
C13
C12 C11
C10 C9
C8
C7
C6
C5 C4
C1
J1
R41
C23
C25
C26
R42
X3
R20
C27
C34 C40
U10
U11
C28
C29 R18
C35
D2
L1
R25 C31 R19
U9
R28 C32 R30
R33
C30
R15 Q2
R21
R23
SW1
C2C3
V1
R36
1002
R
R
S
S
T
T
T
S
R
+
+
1002
R
T
5V
GND
GPC-XP Controller -
Front View
BLACK (R)
BLACK (R)
BLACK (R)
RED (24 VAC)
RED (24 VAC)
To (24 VAC)
Transformer +
To R Terminal On
GPC-XP
To S Terminal On
GPC-XP
To T Terminal On
GPC-XP
To (24 VAC)
Transformer -
BROWN (GND)
Line Voltage
24 VAC Transformer
5 VA Minimum
BROWN (GND)
WHITE (T)
WHITE (T)
WHITE (T)
BARE (S)
BARE (S)
BARE (S)
Run 2 Conductor Twisted
Pair W/Shield Cable.
WattMaster WR-LL-WG-18
Cable Or Equivalent From
System Manager TS To
VCB-X Controller
Run 2 Conductor 20 Ga. Minimum
Cable From System Manager TS
Terminals To 24 VAC Transformer.
System Manager TS - Back View
TERM
NOTE: For Stand-Alone
Installations (No CommLink
or MiniLink), Both TERM
Jumpers Must Be ON.
For All Applications With
CommLink(s) Or MiniLink(s),
Both Jumpers Must Be OFF.
OFF
OPT4 OPT3 OPT2 OPT1
SW1
NOTE: Dip Switch OPT1
Should Be Set To ON When
GPC-XP Is Set To High Speed.
OPT2 & OPT3
. As Of April 2014,
OPT4 Should Be Set To ON
By Default. Previous Versions
Should Be Set To OFF. If You
See Your Screen Is Not
Centered Correctly, Switch
OPT4 To The Opposite
Position.
Should Be
Set To OFF
COM FROM GND
CUT TO ISOLATE
WATTMASTERCONTROLS
YS102432REV3
LOOPCOMM
GND
+24V
+5V
OUTPUTS
ADDRESS
ADD
1
2
4
8
16
32
POWER
EBUS
STATUS2
STATUS1
OUTPUTS
ANALOG
SERIAL #
OUTPUTS
RELAY
SH
R+
T-
BIN8
BIN7
BIN6
BIN5
BIN4
BIN3
BIN2
BIN1
BINARY
INPUTS
INPUTS
ANALOG
0-5v
0-10v
4-20 mA
AOUT1-2
C14
R109
TB8
U19
U17
TB7
TB6
TB4
TB3
TB2
TB1
SW1
R97
R74
R61R59R55R51
R47
R43
R41
R38
R21
R16
R14
D13
D12
D10
D9
D8
D7
D6
C46
C36
C21
RLY1
RLY2
RLY3
RLY4
COMMON
MADEIN USA
RLY1
RLY2
RLY3
RLY4
COMMON
AOUT1
AOUT2
AOUT3
AOUT4
GND
GND
1002
1002
.1uF
.1uF
AOUT3-4
GND
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
1002
.1uF
.01uF
LOOP
BAUD
1
2
AI7
AI8
AI6
AI5
AI4
AI1
AI2
AI3
GND
GND
GND
GND
AI8
AI7
AI6
AI5
AI4
AI3
AI2
AI1
THERM
VDC
300
300
300
300
300
300
300
300
COM
COM
COM
COM
D11
CONNEC
ONBOA
COMMLI
RELAYCONTACT
RATING IS 1 AMP
MAX @ 24 VAC
RS-485 COMMUNICATION LOOP
. WIRE
“R” TO “R”, “T” TO “T” “SHLD”TO“SHLD”
RELAY2
RELAY6
RELA
Y1
RELA
Y5
RLY 1 =
VDC
OUTPUTS
AI1 =
+ 24 VDC
+ 5 VDC
GND
BI1 = AO1 =
AI2 = BI2 = AO2 =
AI3 = BI3 = AO3 =
AI4 = BI4 = AO4 =
AI5 = BI5 =
AI6 = BI6 =
AI7 = BI7 =
AI8 = BI8 =
RLY 2 =
RLY5=
RLY 3 =
RLY 6 =
RLY 4 =
RLY 7 =
RLY 8 =
RELA
Y3
RELAY7
RELAY4
RELAY8
COMMON
COMMON
USB
PORT
E-BUS
PORT
NOTES:
1.) ANALOGINPUTJUMPER SETTINGS MUST BE
SET FORYOUR SPECIFIC INPUT DEVICE
REQUIREMENT.
2.) IT IS RECOMMENDED THATYO
UWRITE THE
DESCRIPTIONOFTHE INPUT,AND/OR
OUTPUTS YOUARE CONNECTINGTO THE
CONTROLLER IN THEBOXES PROVIDED ABOVE
USINGAPE
RMANENT MARKER (SHARPIE) FOR
FUTUREREFERENCE.
®
24 VAC POWER ONLY
WARNING!POLARITY MUST BE OBSERVED
ORTHE CONTROLLER WILL BE DAMAGED
www.wattmaster.com
AI1
AI2
AI3
AI4
AI5
AI6
AI7
AI8
THERM
4-20mA
0-10V
0-5V
ANALOG
INPUT
JUMPERS
LED BLINK C ODES
LED NAME STATUS1 STATUS2
NORMAL OP ERATION 0 1
SCHEDULE OV ERRIDE 0 2
OE338-23-GPC-XP
GPC-XP CONTROLLER
WattMaster Label
#LB102095
Rev.: 1C
+24VAC
GND

Zone
Zone
NAVIGATION
SMTS II for GPC-XP Technical Guide
8
Main Screen Icons and Button Functions
Icons and Button Functions
System settings and screens are easily accessible by simply touch-
ing one of the five icons on the Main Screen. The subscreens contain
green outlined data entry boxes with accessible number keypads for
data entry and screen maneuvering buttons such as <Esc>, <Back>,
and <OK>.
NOTE: Do not attempt to make changes to the Touch Screen
while the GPC-XP is initializing. This can cause
programming errors.
Main Screen Icons
There are five Main Screen icons. See Table 1 for a list of the Main
Screen icons and their functions.
Icon Main Screen Icons
The <Login> icon takes you to the Login
Screen where you enter your passcode.
In a networked system, the <My System>
icon takes you to a Unit Selection Screen
which takes you directly to the GPC-XP
Controller’s Status Screen. In a stand-alone
system, the <My System> icon takes you
directly to the Status Screen.
The <User Passcodes> icon takes you
to the System Manager Passcode Levels
Screen if you are a Level 3 user.
The <Settings> icon takes you to the
System Settings Screen where you can
change the Backlight settings, set the
System Manager address, or choose One
to One Unit Connection (stand-alone
connection). System settings are only
accessible to a Level 3 user.
The <Set Time & Date> icon takes you to
the Set Time and Date Screen. Any level of
user can set the time and date.
Navigation Buttons
See Table 2 for a list of Navigation buttons and their functions.
Button Function
Back
Use the <Back> button while in a Data Entry
Screen to return to the Status Screen. Use
the <Back> button while in a Status Screen
to return to the Main Screen.

+Use the <+> key to step to the next screen.
-Use the <-> key to step to the previous
screen.
Data Entry, Selection, and Alarm Buttons
See Table 3 for a list of data entry, selection, and alarm buttons and
their functions.
Button Function
Esc Use the <Esc> (Escape) key to exit from data
entry without saving any new data.
OK Use the <OK> key to save the data you just
selected or entered.
Touch the gray radio button to make your
selection. A white circle will designate that the
item is selected. You can only select one radio
button item per screen.
Touch the gray square to make your selection.
A white square will designate that the item is
selected. You can select more than one
square per list of items.
No Alarms
The <No Alarms> or <ALARM> button, ap-
pearing on each Status Screen, takes you
directly to the GPC-XP Alarm Status Screen
where you can program alarms and view
active alarms. If red, alarm(s) are present.
If black, no alarm(s) are present.
Table 2: Navigation Button Functions
Table 1: Main Screen Icon Functions Table 3: Configuration Selection Buttons

SMTS II for GPC-XP Technical Guide
MAIN SCREEN FUNCTIONS
9
Entering Your System Manager
Passcode
NOTE: There are three available passcode levels. Level 1 defaults
to 1111, Level 2 defaults to 2222, and Level3defaults to3333. These
defaults can be changed by anyone who logs in at Level 3.
When you power-up your System Manager TS II, the message
System Secured is displayed under the time display at the upper
right of the Main Screen.
Touch the <Login> icon found on bottom left of the
Main Screen and type the default Level 3 passcode of
“3333” using the number keypad to gain access to
all setpoint and configuration items. See Figure 7.
First Things First
The first thing you need to do when setting up your Touch Screen is
to log in.The second thing youneed to do is establish userpasscodes.
The third thing you need to do is set the clock. After you complete
these simple tasks, you are ready to set your system’s settings, view
GPC-XPstatus screens, changeschedules, and performforce modes.
NOTE: Do not attempt to make changes to the Touch Screen
while the GPC-XP is initializing. This can cause
programming errors.
Main Screen
Once you have connected your System Manager TS II to a control-
ler and have powered it up with the proper power supply, the Main
Screen will appear. See Figure 6.
Figure 7: Login Screen
Enter the 4 digit Passcode
for the required Level.
Level #1:
Can change space setpoints.
Level #2:
Can change schedules.
Level #3:
Can change all setpoints.
Esc
123
4
7
-0
.
9
8
56
OK
<<
Currently: ****
DATA ENTRY
Logging In
Figure 6: Main Screen NOTE: For security reasons, the current passcode characters
displayed at the top of the screen are never shown and
appear as asterisks.
Touch <OK>. The Login Screen will automatically close, and the
passcode will be tested against all previously defined passcodes to
determine the passcode’s access level.
If 3333 is still the active Level 3 code, the status message
System
Access Level 3 will now be displayed under the time display at
the upper right of the Main Screen.
NOTE: SystemAccess willautomatically default toSystem
Secured after the time set for Backlight Timeout
in the System Manager Settings Screen (see Figure
12, page 12). If timeout is set to zero, the passcode
will timeout after two minutes.

Zone
Zone
MAIN SCREEN FUNCTIONS
SMTS II for GPC-XP Technical Guide
10
Editing Passcodes
Passcode Clearance Levels
Below is a list of the passcode levels, default codes, and actions that
can be performed at the various levels.
Level 0—No Passcode Needed, System
Secured
Level 0 users can view status screens. They can also
change the system date and time. No other changes can
be made at this level.
Level 1—Default: 1111
Level 1 users can view status screens. They can also
change the system date and time. Alevel 1 user can also
temporarily override a schedule.
Level 2—Default: 2222
Level 2 users can view status screens. They can also
change the system date and time. Level 2 users can also
set schedules and holidays and temporarily override a
schedule.
Level 3—Default: 3333
Level 3 users have system manager access and can
change all configurations, including default passcodes.
Level 3 users can also access force modes. This Level
is normally reserved for qualified HVAC service per-
sonnel.
Edit Passcodes
WARNING: MAKE SURE YOU CHANGE ALL PASS-
CODES AS SOON AS POSSIBLE TO SECURE THE
SYSTEM!
NOTE: Only a Level 3 user (system manager level) can change
Level 1, 2, and 3 passcodes.
NOTE: Do not use the same passcode for all 3 levels. If you do,
each passcode will default to Level 1.
From the Main Screen, touch the <User Pass-
codes> icon.The System Manager Passcode Levels
Screen will appear. See Figure 8.
To change a passcode, touch the blue highlighted box containing
the current passcode. The keypad will appear with instructions for
changing the passcode. See Figure 9.
The current passcode will appear on the top menu bar. Type in the
new four-digit passcode. You cannot use the period or minus char-
acters in your passcode. Use the <<<>key if you make a mistake.
Touch <Esc> to return to the previous screen without changing the
passcode. When you have typed in the new passcode, touch <OK>.
The System Manager Passcode Levels Screen should now display the
passcode that you entered.
NOTE: Ifyou change the Level 3passcode, make sure to write
it down. If you should happen to forget the Level 3
passcode, contact WattMaster Technical Support.
Touch <Back> to return to the Main Screen.
Figure 8: System Manager Passcode Levels Screen
1111
Passcode Levels
You can limit access to critical settings
by giving the user access only to those
items needed to maintain comfort levels
or to modify operating hours.
All critical setpoints and configurations
are protected by Level #3 and should not be
accessed except by a service technician.
Level #1 Passcode
{ Temporary Schedule Overrides }
2222
Level #2 Passcode
{ Can change Schedules & Holidays }
3333
Level #3 Passcode
{ Can change All Setpoints }
Back
Enter the 4 digit Passcode
for the required Level.
Esc
123
4
7
-0
.
9
8
56
OK
<<
Currently: ****
DATA ENTRY
Level #1:
Can temporarily override schedules.
Level #2:
Can change schedules and holidays.
Level #3:
Can change user passcodes and
access force modes.
Figure 9: Change Passcode Screen

SMTS II for GPC-XP Technical Guide
MAIN SCREEN FUNCTIONS
11
Setting the System Clock
Set Time and Date
When you first power up your System Manager TS II, you will need
to change the day of the week, the time, and the month, day, and
year to the current time and date. If your system has been turned
off or has been down for a long time, you may have to do the same,
although the time and date can maintain itself for several days. Any
level of user can change the time and date settings.
The day of the week, the time, and the date appear at the top right
on the Main Screen. See Figure 6, page 9.
From the Main Screen, touch the <Set Time &
Date> icon.The Set Time & Date Screen will appear.
See Figure 10.
In the example above, the current time and date is 2:12 PM, January
16, 2014. There is no day of the week selected yet.
Set Day of the Week: Select the day of the week by simply
touching your selection. The day of the week text will change from
white to blue.
Set Hour, Minute, Month, Day, and Year: Touch the blue high-
lighted box to have each selection screen appear. See Figures 10 &
11. Read the instructions on each screen for entering data.
Broadcast: When you are finished setting the clock, touch the
<Broadcast> button to broadcast the Time and Date to all Units.
The following message will appear:
Figure 10: Set Time & Date Screen
Back
Set Time & Date
Broadcast
System Manager Settings
Mon Tue Wed
Hour Minute
Month
Day Year
14 12 116 14
Sun Thu
Sun
Thu Fri
Sun
Fri Sat
Sun
Sat
Esc
123
4
7
-0
.
9
8
56
OK
<<
Currently: 10
DATA ENTRY
Set Clock Hour
Enter the Current Hour in
24 hour military format.
Example:
5:00 AM = 5
5:00 PM = 17
Hi Limit: 23
Lo Limit: 0
Figure 11: Set Clock Hour
Set Clock Hour: Touch the number buttons to enter the current hour
in 24 hour military format. Valid entries are from 0-23. Press <OK>.
NOTE: See Appendix on page 20 for a Military Time
Conversion table.
Set Clock Minute: Touch the number buttons to enter the current
minutes. Valid entries are from 0-59. Press <OK>.
Time & Date Broadcast to All Units.
OK
Set Clock Month: Touch the number buttons to enter the current
month. Valid entries are from 1-12. Press <OK>.
Set Clock Day: Touch the number buttons to enter the current day
of the month. Valid entries are from 1-31. Touch <OK>.
Set Clock Year: Touch the number buttons to enter the current year.
Valid entries are from 0-99. Touch <OK>. Note: The year is based
on the current century; therefore, 14 = 2014. If you enter more than
two digits, e.g. 2014, the system will not recognize your entry.

Zone
Zone
MAIN SCREEN FUNCTIONS
SMTS II for GPC-XP Technical Guide
12
System Manager Settings
Figure 12: System Manager Settings Screen
30
System Manager Settings
Backlight Timeout
Backlight Intensity
System Manager Address
Back
30 Minutes
3050 %
3063
One to One Unit Connection
System Manager Version: 1.02
System Manager Settings
Additional system settings are available under the <Settings>
icon. These include setting the Backlight Timeout, the Backlight
Intensity Percentage, the System ManagerAddress, and One to One
Unit Connection.
From the Main Screen, touch the <Settings> icon.
The System Manager Settings Screen will appear. See
Figure 12.
Backlight Timeout: This setting is actually a setting for three
separate functions—Backlight Timeout, Main Screen Timeout, and
Passcode Timeout. To set the Backlight Timeout, enter the amount
of time you wish the screen to maintain the active intensity level
after the last touch pad activity occurs. The High limit is 30 and the
Low limit is 0. 0 = No Timeout. The System Manager TS II will
return to the Main Screen display at the same rate as the Backlight
Timeout, except that if set to 0, the Main Screen will display after 2
minutes. The Passcode will timeout at the same rate as the Backlight
Timeout, except that if set to 0, the Passcode will timeout after 2
minutes and will return to System Secured Setting.
Backlight Intensity Percentage: Enter the percentage of light
level you wish to maintain whenever touch pad activity occurs. The
High limit is 100 and the Low limit is 0.
System Manager Address: Enter the address of the System
Manager TS II. 0 = StandAlone Mode. 63 = Network System. 1-60
= Multiple Managers based on the following definitions:
•
Stand Alone—If your System Manager TS II is connected to
one controller and you are not using a CommLink or MiniLink
anywhere on the loop, your system is Stand Alone. If your
System Manager TS II is connected to more than one controller
daisy-chained together and you are not using a CommLink or
MiniLinkanywhereon theloop, yoursystem isInterconnected.
If you have either a Stand Alone or Interconnected system,
you must enter <0> for Stand Alone Mode. In order to view
all controllers on an Interconnected System, make sure that
One to One Unit Connection, described below, is not selected.
•
Network—If youare usingthis SystemManagerTSIIonacom-
munications loop that has a MiniLink or CommLink installed
and you have a single System Manager TS II for your entire
system, you must enter <63> for Network System.
•
Multiple Managers—If you are using this System Manager TS
II on a communications loop, have a MiniLink or CommLink
installed, and have more than one System Manager TS II, then
you need to operate in MultipleManagersMode. Enter the ad-
dress <1-60> at which you want thisparticular System Manager
TS II to be set. When more than one System Manager TS II
is used on a local loop, each must be set with a unique address
different from any other device on that loop. If you want one
of the System Manager TS II’s to be able to indicate alarms for
the entire system, you must enter <63> for Network System
for that particular System Manager TS II.
One to One Unit Connection: If your System Manager TS II
is directly connected to the GPC-XP Controller, you may wish to
select this option to bypass the Unit Selection Screen and go directly
to the unit’s Status Screen. The controller must be set to address #1
for this to work. Touch the black box to the left of this item on the
screen to select it. The box will turn white. If you wish to deselect
this option, simply touch the box again.
System Manager Version: The version number of the System
Manager software appears on the bottom menu bar. This version
number is important to know for troubleshooting purposes.

SMTS II for GPC-XP Technical Guide
GPC-XP CONTROLLER SCREENS
13
Unit Selection and Analog Inputs
My System Unit Selection
From the Main Screen, touch the <My System> icon.
The Selected Unit Screen will appear. See Figure 13.
NOTE: If you have chosen the One to One Unit Connection
in the System Manager Settings Screen, this screen
(Figure 13) will not appear. Instead, the unit’s first
Status Screen will appear.
Back
Selected Unit [Loop 1 - Unit 1]
1
GO
010
- - - -
+ + + +
Figure 13: Unit Selection Screen
InFigure13, Loop 1and Unit 1are selected asindicated inthefigure
with white text. They also appear in the Top Menu Bar in brackets.
Use the <+> and <-> buttons to move up and down through the loops
and units. Enter the desired Loop # and Unit # and then touch <GO>
to access the unit’s Status Screen.
Viewing / Configuring GPC-XP Status
Screens
Figures 14-27 depict the GPC-XP Status Screens and corresponding
data entry screens associated with them. Notice that the controller
is identified by loop number and unit number - in this case, 0001
represents Unit 1 with a stand-alone connection.
Figure 14: Analog Inputs Screen
While in each Status Screen, touch the <+> and <-> buttons to view
more status screens. These screens roll back to the first Status Screen.
Figure 15: Analog Input Details Screen
Analog Inputs: Thermistor sensors can be calibrated and all read-
ings can be overridden to specific values by Level 3 users. To do
this, while in the Analog Input Screen, touch the value field for the
sensor you would like to calibrate or override.
In this example below (Figure 15), Analog Input #1 - OSA Tem-
perature Sensor is selected.
Calibrate Sensor: To calibrate a thermistor sensor, touch the Cali-
brate Sensor value field. The Data Entry Screen will appear. Type a
positive value to increase the reading or a negative value to decrease
thereading.High Limit:+100.Low Limit:-100.Press<OK> to save.
Figure 16: Calibrate Sensor Data Entry Screen

Zone
Zone
GPC-XP CONTROLLER SCREENS
SMTS II for GPC-XP Technical Guide
14
Figure 18: Binary Inputs Screen
Figure 20: Relay Outputs Screen
Figure 19: Binary Input Force Mode Screen
Binary Inputs: Level 3 users can force a binary input on or off or
to return it back to normal operation. To do this, while in the Binary
Inputs Screen (Figure 18), touch the value field for the binary input
you would like to force on or off.
In this example that follows (Figure 19), Binary Input #1 - Chilled
Water Flow - is selected.
You can now select the radio button for the force mode—Normal
Operation, Force Input Active, or Force Input Off.
Relay Outputs: Level 3 users can force a relay on or off or to return
it back to normal operation. To do this, while in the Relay Outputs
Screen (Figure 20), touch the value field for the Relay you would
like to force on or off.
In the example below (Figure 21), Relay Output #5 - Tower Fan
- is selected. Touch the Tower Fan’s data field. The Relay Output
Force Mode Screen will appear (Figure 22).
Figure 21: Relay Output Details Screen
Analog Inputs, Binary Inputs, and Relay Outputs
Override Reading: To override a reading for a thermistor sensor,
touch the Override Reading value field. The Data Entry Screen will
appear. (Figure 17) Type a value that will override the actual sensor
reading and press <OK> to save. High Limit: 3000. Low Limit: -80.
Clear Sensor Override: To clear an override for a thermistor sen-
sor, touch the Override Reading value field. The Data Entry Screen
will appear. (Figure 17) Type -90 to clear a sensor override that was
entered. Press <OK> to save.
Figure 17: Sensor Override Data Entry Screen

SMTS II for GPC-XP Technical Guide
GPC-XP CONTROLLER SCREENS
15
Figure 22: Relay Output Force Mode Screen
Figure 26: Outdoor and AVC Status Screen
Figure 27: Schedules and Holidays Screen
Figure 23: Analog Outputs Screen
Figure 24: Analog Output Detail Screen
Figure 25: Analog Output Force Screen
Relay Output Force Modes, Analog Outputs, and Analog Force
Relay Force: You can now select the radio button for the force
mode—Normal Operation, Force Relay On, or Force Relay Off.
Runtime Reset: You can also touch the Runtime Hrs and Runtime
Minutes data field to reset Runtimes (Figure 21).
Analog Outputs: From the Analog Outputs Screen (Figure 23)
you can access the detail screen by selecting one of the data fields.
In the example below (Figure 24), Tower Fan Speed is selected.
Force Analog Output: From the Analog Output Detail Screen
(Figure 24), you can access the Force Screen (Figure 25 above)
by selecting the Force Value data field. Enter a percentage between
0 and 100. Enter -1 to Cancel the Force Mode.
Outdoor and AVC Status: This screen (Figure 26) is for view-
ing only.
Schedules & Holidays: Refer to the next section for instructions.

SCHEDULES
SMTS II for GPC-XP Technical Guide
16
Viewing and Setting Schedules
Viewing and Setting Schedules
You can view and set schedules from GPC-XP Status Screen #6.You
can set up to 8 different schedules. See Figure 28 below.
To set a schedule, touch the <ON> or <OFF> button to the right of the
Schedule #. The Week Schedules Screen will appear. See Figure 29.
The default day will be Sunday and the default event start/stop times
will be midnight.
Figure 28: Status Screen #6 - Schedules
Figure 30: Schedule Times Screen
A Level 2 user can set two schedules per day for individual days
of the week, all weekdays, weekends, and holidays. All times are
entered in military time format.
If you wish to enter a schedule for a certain day of the week, first
touch the day of the week at the top of the screen. Otherwise, the
day defaults to Sunday.
Touch the start and stop time for each Event and enter the desired
times. See Figure 29. All times must be entered in military time
format. See the Military Time Table in the Appendix,page 20.
Touch <OK> to save the time you entered or touch <Esc> to exit the
Schedule Times Screen without changing the time and return to the
Week Schedules Screen (Figure 29).
To eliminate a schedule from any event, simply enter a zero for the
Start and Stop time for that day. The screen will display 12:00 am
for both the Start and Stop times, indicating that the equipment will
not activate on that day.
Once back at the Week Schedules Screen, you can continue setting
schedules day by day or use following options:
SEND TO <All Days> - Touch this button to send the schedule ap-
pearing on the screen to all days of the week, except for holidays.
SEND TO <Weekdays> - Touch this button to send the schedule
to weekdays only. You will need to set up a separate schedule for
Saturday and Sunday when selecting this option.
CLEAR <All Schedules> - Touch this button to clear all schedules.
SET <24 Hr Mode> - Touch this button to have the system run
continuously, 24 hours a day, 7 days a week including holidays. All
event times will display 11:59 PM.
Figure 29: Week Schedules Screen

HOLIDAYS & SCHEDULE OVERRIDE
SMTS II for GPC-XP Technical Guide 17
Schedule Override
Level 1, 2,and 3 userscan override schedules.To override a schedule,
while at Status Screen #6 (Figure31), touch the <AUTO>, <ON>, or
<OFF> button next to the <NORMAL> button. The Schedule Over-
ride Screen will appear (Figure 33 below):
Touch the radio button to select the schedule option. Default is
Schedule AUTO Mode. This selection will remain in effect unless
it is changed again on this screen. Schedule overrides do not auto-
matically time out after a certain period of time.
  Schedule AUTO Mode—Select this to restore normal
schedule operation.
  Schedule FORCED ON—Select this to Force the unit into
continuous Occupied Mode operation.
  Schedule FORCED OFF—Select this to Force the unit
into continuous Unoccupied Mode operation.
Viewing and Setting Holidays
You can set holidays from Status Screen #6. See Figure 31 below.
You can set up to 8 different holiday schedules.You must be a Level
2 user in order to set holidays.
To viewandset holidays,touch the <NORMAL> button forthe desired
Schedule #. The Holidays Schedule Screen will appear, starting with
the current month and year. See Figure 32.
Figure 32: Holidays Schedule Screen
Figure 31: Status Screen #6 - Schedules
The holidays in the screen will initially not be set. You can only set
holidays for the current year. Simply touch the day(s) of the month
to select holidays. Touch the <<> button to go back one month and
the <>>button to go forward one month.
There are 14 holiday periods available for each year. These holiday
periods can be a single day or they can span days, weeks, or even
months.
For example, if you wantto schedule a summer break, you needonly
schedule one holiday period to define a two or three month break
from operating in the occupied mode.
Viewing and Setting Holidays & Schedule Override
Figure 33: Schedule Override Screen
Every defined holiday uses the Holiday operating schedule pro-
grammed in the controller’s Schedules Screen.
Holidayscanonlybeprogrammed for thecurrentyear.Youcannotprogram
holidays before the next year occurs. Holidays do not automatically
adjust for the new year, so you will need to access this screen after
the new year and make necessary adjustments to the days that float,
such as Memorial Day.

Zone
Zone
VCM-X CoVCM-X Co
ALARMS
SMTS II for GPC-XP Technical Guide
18
In addition to simply viewing alarms, the Alarm Status Screen can
also be used for enabling and disabling alarms that will be emailed
or texted. The emailing and texting feature will only work if Prism
2 is running and has emailing capability.
The alarms must first be configured using Prism 2 software. Once
the alarm settings have been established in Prism 2, the settings you
choose in the Alarm Status Screen will be stored in the controller so
that you will not have to reconfigure the alarms for that controller
in Prism 2. Once configuration is complete, Prism 2 does not have
to be running in order to view alarms on the Alarm Status Screen in
the System Manager TS II. However, as mentioned previously, Prism
2 does have to be running for emailing or texting alarms to occur.
To enable an alarm, simply touch the gray square next to each alarm.
Awhite box designates thatthe alarm is enabled.To disable the alarm,
simply touch the square again. A gray box designates that the alarm
category is disabled.
When an alarm is enabled and there is no alarm condition, the word
OK appears in a box next to the type of alarm. When an alarm occurs,
this box will turn red and will read ALARM.
Figure 35: GPC-XP Controller Alarm Status Screen
Viewing/Enabling/Disabling Alarms
To view or configure alarms, touch the <No Alarms>
or <ALARM> button on any of the Status Screens. See
Figure34.The GPC-XP AlarmStatus Screen willdisplay.
See Figure 35.
NOTE: The <ALARM> button only appears red on the
screen if the unit has an active alarm condition.
Only a Level 3 user has the option to enable or
disable each type of alarm.
Viewing and Enabling/Disabling Alarms
Figure 34: GPC-XP Status Screen 1
No Alarms

ntrollersntrollers
SMTS II for GPC-XP Technical Guide
APPENDIX
19
Troubleshooting
System Manager TS II LEDs, Buttons,
Dipswitches & Jumpers
LEDs and system function buttons are located behind your System
Manager TS II’s cover. See Figure 36 for locations. Dipswitches
and jumpers are located on the back of your System Manager TS.
Power LED
This LED will light up and stay on as long as power is supplied to
your TS.
Operation LED
ThisLEDwill blinkoncea secondto indicate thatthe systemisalive.
Update LED
This LED will turn on when the Update program is running.
Screen Refresh LED
This LED will turn on when the screen refreshes.
Communications LED
This LED will light up and blink when there is a connection with the
CommLink and/or network. If you are using your TS in stand-alone
mode, this LED will not light up.
Reset Button
Press this button to reset the screen. The screen should refresh itself
to the Main Screen within 2 minutes.
Diagnostics Button
Under the direction of WattMaster Controls Technical Support, you
may have to perform diagnostics on your System Manager TS II.
Press this button to do so.
Touch Screen Suspend Button
Press this button to temporarily freeze the touch screen function of
your System Manager TS II in order to clean the screen.Always use
a dry, dust-free cloth to clean the screen.
OPT1 Dipswitch
OPT1 Dipswitch should be ON if the GPC-XPis set to High Speed.
This Dipswitch is located on the back of the System Manager TS.
See Figure 5, page 7 for location.
OPT4 Dipswitch
As of April 2014, Dipswitch OPT4 should be set to ON by default.
Previous versions should be set to OFF. If you see your screen is
not centered correctly, switch OPT4 to the opposite position. This
Dipswitch is located on the back of the System Manager TS. See
Figure 5, page 7 for location.
TERM Jumpers
Both TERM Jumpers must be ON for Stand-Alone applications
(No CommLink or MiniLink). Both TERM Jumpers must be OFF
for applications with CommLink(s) and/or MiniLink(s). See Figure
5, page 7 for location.
Reset Button
A302-12
Power LED Communications LED
Diagnostics Button
Suspend Button
Not Used
Not Used Screen Refresh LED
Operation LED
Update LED
Figure 36: System Manager TS II LEDs and Buttons

Zone
Zone
VCM-X CoVCM-X Co
APPENDIX
SMTS II for GPC-XP Technical Guide
20
Military Time Conversion
The main difference between regular and military time is how hours
are expressed. Regular time uses numbers 1 to 12 and a.m. and p.m.
to identify each of the 24 hours in a day. In military time, the hours
are numbered from 0000 to 2300.
Military time is based on a 24-hour day. Hours are numbered 0000
through 2300 and are recorded first. The last two digits indicate the
minute after the hour. Military time does not exceed 2359 hours. For
example, midnight is recorded as 0000, one minute past midnight is
0001, 1 a.m. is 0100, 1 p.m. is 1300, and so on.
Regular and military time express minutes and seconds in exactly
the same way. When converting from regular to military time and
vice versa, the minutes and seconds do not change.
Regular time requires the use of a.m. and p.m. to clearly identify the
time of day. Since military time uses a unique two-digit number to
identify each of the 24 hours in a day, a.m. and p.m. are unnecessary.
The following table summarizes the relationship between regular
and military time.
Regular
Time Military Time
12:00 a.m. 0000
12:30 a.m. 0030
1:00 a.m. 0100
1:30 a.m. 0130
2:00 a.m. 0200
2:30 a.m. 0230
3:00 a.m. 0300
3:30 a.m. 0330
4:00 a.m. 0400
4:30 a.m. 0430
5:00 a.m. 0500
5:30 a.m. 0530
6:00 a.m. 0600
6:30 a.m. 0630
7:00 a.m. 0700
7:30 a.m. 0730
8:00 a.m. 0800
8:30 a.m. 0830
9:00 a.m. 0900
9:30 a.m. 0930
10:00 a.m. 1000
10:30 a.m. 1030
11:00 a.m. 1100
Regular
Time Military Time
11:30 a.m. 1130
12:00 p.m. 1200
12:30 p.m. 1230
1:00 p.m. 1300
1:30 p.m. 1330
2:00 p.m. 1400
2:30 p.m. 1430
3:00 p.m. 1500
3:30 p.m. 1530
4:00 p.m. 1600
4:30 p.m. 1630
5:00 p.m. 1700
5:30 p.m. 1730
6:00 p.m. 1800
6:30 p.m. 1830
7:00 p.m. 1900
7:30 p.m. 1930
8:00 p.m. 2000
8:30 p.m. 2030
9:00 p.m. 2100
9:30 p.m. 2130
10:00 p.m. 2200
10:30 p.m. 2230
11:00 p.m. 2300
11:30 p.m. 2330
Table 6: Military Time Conversion
Military Time Conversion
Table 6, cont.: Military Time Conversion