Osaki Power Tools CS36TR User manual

E C LOW VOLTAGE DIRECTIVE 73/23/EEC
E C ELECTROMAGNETIC COMPATIBILITY DIRECTIVE 89/336/EEC
E C MACHINERY DIRECTIVE 89/392/EEC
DECLARATION OF CONFORMITY
We hereby certify that OSAKI CS36TR Cordless Screwdriver
Complies with all the relevant provisions of the
EC Directives 73/23/EEC, 89/336/EEC, 89/392/EEC
Harmonised Standards Applied: HD400-1, HD400-2,
EN50082-1, EN55014, EN60555-2, EN60555-3.
Official Agent
KENNEDY TOOLS
Wigston Works, Leicester, England.
ISO 9001 REGISTERED COMPANY
Signed:
Date: 1st April 2003 Name: Martin Cooke Position: Director, The Kennedy Group Ltd.
Pozidriv
®
and Torx
®
are registered trade marks and the property of their respective owners.
© The Kennedy Group Ltd. 04/03
QUALITY GUARANTEE & WARRANTY
OSAKI POWER TOOLS carry one years manufacturers warranty.
OSAKI POWER TOOLS are designed & produced
to the highest standards & specifications
OSAKI POWER TOOLS are fully guaranteed against
faulty materials & workmanship
Should they be found to be defective, they will either be repaired or replaced
free of charge (fair wear and tear and/or misuse excepted).
Please retain supplier invoice as proof of purchase.
AVAILABLE FROM YOUR DISTRIBUTOR
CORDLESS SCREWDRIVER WITH TORCH
CS36TR
OPERATORS MANUAL
Please read all of this manual before using your tool and retain for future reference.
TWIN BULB
ILLUMINATION
SUPPLIED
COMPLETE
WITH 36
ACCESSORIES
ORDER CODE
OSA-279-6340K
WITH TORCH LIGHT
& SPINDLE LOCK
OSA-279-6340K_Instructions.qxd 25/06/2008 09:13 Page 1

23
SAFETY INSTRUCTIONS CONTENTS
OPERATING
MAINTENANCE
Osaki Power Tools are committed to the Production of Quality Power Tools
that are designed for high performance and long service life.
If safety and maintenance procedures are observed they will last for many years.
Man, Earth and the Universe
are forces that create an
immovable centre of balance . . . the
balance of power
“
”
GENERAL SAFETY
Keep work area clean - clutter invites
injuries.
Do not expose power tools to rain or
damp conditions. Do not use power tools
near flammable liquids or gases.
Do not let people who are not familiar
with power tools handle them without
supervision. Keep children away from the
work area.
Store tool in dry, secure place, away
from children.
Use correct tool for the job, do not force
small tools or attachments to do the job
of a heavy tool. The job will be done
more efficiently and safely if the tool is
used for the intended application.
Wear safety glasses or a dust mask if
necessary.
Secure work with a clamp or vice. This
will allow both hands free to operate the
tool.
Before using tool ensure that all parts
are functional. A damaged part should be
repaired and serviced by an authorised
technician.
Stay alert at all times. Watch what you
are doing and use your common sense.
Do not operate tools when you are tired.
Do not overreach. Keep a proper footing
and balance at all times.
Do not force the tool. It will do the job
better and safer at the rate for which it
was intended.
Do not attempt to use the tool whilst it is
connected to the charger.
Do not carry the charger by its cord.
Do not use the charger if it is cracked,
has been dropped or the cord is
damaged in any way .
Do not charge battery below 4°C (40°F)
or above 40°C (104°F).
Do not attempt to open the screwdriver
or battery charger for any reason.
Do not store the screwdriver in locations
where the temperature may reach or
exceed 40°C (104°F).
Guard against electric shock. Prevent
body contact with grounded surfaces; for
example, pipes and radiators.
If you drive through a “live” wire do not
touch any metal part of the tool until
after isolating the power and full
withdrawal.
Do not alter the tool or the charger.
Model Number CS36TR
Nominal Voltage 230v
~ 50 Hz
Battery 3.6V
Torque 45 Kgf-cm
No Load Speed 200 rpm
Gross Weight 1.58kg
Screwdriver Weight Only 603gm
1 x SOCKET ADAPTOR
1/4” x 50mm
9 x SOCKETS
4, 5, 6, 7, 8, 9, 10, 11, & 12mm
Plus holder.
5 x HSS DRILL BITS
1/4” - 1.5, 2, 3, 4, 5.5mm
Fitted with 1/4” Hex drive bits.
1 x SCREWDRIVER
3.6V Cordless
1 x CHARGER
3 hour
1 x CARRY CASE
Fitted to hold all accessories.
1 x BIT HOLDER
1/4” x 60mm
20 x
1/4
” HEX DRIVER BITS
CROSSPOINT HEAD 1, 2 & 3
POZIDRIV
®
1, 2 & 3
SLOTTED 3, 4 & 5mm
HEX 2, 2.5, 3, 4, 5, 6mm
TORX
®
T10, T15, T20, T25 & T30
Plus 2 holders.
Before drilling in ceilings and walls check for concealed electric wires and gas/water pipes using a
metal detector. Keep long hair away from drill. Do not operate while wearing loose clothing.
FORWARD/REVERSE SWITCH OPERATION
Press on the left side of the switch to remove fasteners with a
counterclockwise rotation. (See Fig. a)
Press on the right side of switch to drive/install fasteners with a
clockwise rotation. (See Fig. a)
LOCKING THE SCREWDRIVER
The Osaki Cordless Screwdriver is fitted with an automatic
spindle lock which engages when the motor is not active,
to allow it to be used as a manual screwdriver.
TORQUE ADJUSTMENT COLLAR
The screwdriver has 12 torque positions. To change settings,
turn the torque adjustment collar to the left from setting 1 to increase the
torque and back towards the right to decrease the level of torque. When
the optimum torque position for a particular application is not known it
is recommended to start at a low position and “work up” until the right
setting is achieved. This will avoid unnecessary damage of the workpiece.
(See Fig. b) Do not attempt to force the collar past the number 12 torque
position.
TURNING ON THE LIGHT
To turn the light on, rotate the light switch collar to the right until the bottom
triangle aligns with the light symbol. (See Fig. c)
The exterior plastic parts of the screwdriver may be cleaned with a damp cloth and a mild detergent.
The charger should only be cleaned using a dry cloth or a soft non-metallic brush. Do not use water or
detergent.
WARNING: Disconnect the charger from the mains power supply outlet before cleaning.
Fig. a
Fig. b
Fig. c
OSA-279-6340K_Instructions.qxd 25/06/2008 09:13 Page 2