Osaki Power Tools CS36Li User manual

QUALITY GUARANTEE & WARRANTY
OSAKI POWER TOOLS carry one years manufacturers warranty.
OSAKI POWER TOOLS are designed & produced
to the highest standards & specifications
OSAKI POWER TOOLS are fully guaranteed against
faulty materials & workmanship
Should they be found to be defective, they will either be repaired or replaced
free of charge (fair wear and tear and/or misuse excepted).
This does not affect your legal rights.
Please retain supplier invoice as proof of purchase.
Osaki Power Tools are designed for DIY and hobby use only.
They are not covered by an industrial warranty. Industrial use will invalidate this guarantee.
OPERATOR’S MANUAL
3.6V CORDLESS SCREWDRIVER
ORDER CODE
OSA-279-7100K
CS36Li
• Suitable for DIY,
home improvement
and workshop use.
• Compact design allows
you to get into tight spaces.
• Powered by a high capacity lithium-ion
battery.
• ONLY weighs 350g
• 7 torque settings
• Forward/reverse & spindle lock
• Integral 3 LED worklight
• Ergonomic bi-material grip for comfort
with wrist strap
• 3 colour LED battery condition lights
© The Kennedy Group Ltd. 09/11
EC DECLARATION OF CONFORMITY
Osaki Power Tools continually strives to improve its products. Specifications may change without prior notice.
OSAKI TOOLS Official Agents - JAPAN: MIKI TOOL TRADING CO. MIKI CITY, JAPAN.
EUROPE, MIDDLE EAST, AMERICA & AFRICA: KENNEDY TOOLS, WIGSTON, ENGLAND.
DECLARATION OF CONFORMITY
We hereby certify that OSAKI CS36Li Screwdriver and Charger
complies with all the relevant provisions of the following directives:
Electromagnetic Compatibility 2004/108/EC (Charger), Low Voltage 2006/95/EC (Charger)
Electromagnetic Compatibility 2004/108/EC (Screwdriver), Machinery 2006/42/EC (Screwdriver).
Official Agent
KENNEDY TOOLS
Wigston, Leicester, England.
Signed:
Date: 1st September 2011 Name: Martin Cooke Position: Director, The Kennedy Group Ltd.
Osaki, Osaki Xtra-plus and the round Mitsudomoe logo are trade marks of Osaki Tools.
OSA-279-7100K_Instructions.qxd 22/08/2011 07:53 Page 1

SYMBOLS USED WITH THIS PRODUCT
SAFETY INSTRUCTIONS
72
Man, Earth and the Universe
are forces that create an
immovable centre of balance . . . the
balance of power
“
”
Read operator’s
manual
Double
insulated
Centre
positive
Recycle
See page 5
Short - circuit proof
safety transformer
For indoor use
only
WEEE
See page 5
European
Conformity
WarningRoHS
See page 5
Plug type
OTHER OSAKI
SPECIFIC OPERATING HAZARDS
Always use the corresponding charger that
comes with the Screwdriver.
Never operate the Screwdriver whilst charging.
Never charge the Screwdriver in a damp or wet
environment. The charger is for indoor use only.
Never charge the Screwdriver in an air
temperature below 40°F (4.5°C) or above 105°F
(40.5°C). This could cause serious damage to
the battery.
Never cover the charger, use it in direct sunlight
or near heat sources.
GENERAL OPERATING HAZARDS
Always stay alert and watch what you are doing.
Always ensure the tool is kept in a good working
condition. Do not use the tool if any parts are
missing or damaged. Ensure servicing and repair
is undertaken by a suitably qualified person.
Never modify the tool or accessories and only
use it for the task for which it has been
designed.
Never force or apply excessive pressure, let the
tool do the work for you.
Never operate the tool when tired or under the
influence of alcohol or prescription/non-
prescription drugs.
Never touch parts of the tool or accessories
when they are moving.
PERSONAL PROTECTION
Always wear approved eye protection when using
the screwdriver.
WORKPLACE HAZARDS
Always keep your work area clean and well lit.
Always maintain a balanced body position and
secure footing.
Always use a vice or clamping device to hold
small work pieces firmly in place.
Always keep children away from the work area
and where tools are stored.
Always be aware of hidden cables and pipes.
Always avoid body contact with earthed or
grounded surfaces such as pipes, radiators and
refrigerators.
Never make contact with electric power sources
as this tool is not insulated.
Never work in a combustible atmosphere.
Osaki Power Tools are committed to the Production of a range of Quality Power Tools
that are designed for high performance and long service life. By following the recommended
safety and maintenance procedures they will last for many years.
OSA-279-7100K_Instructions.qxd 22/08/2011 07:53 Page 2

36
Save the packaging material for future transportation of the Screwdriver in the event of service
or repair.
SPECIFICATIONS
BOX CONTENTS
Model Number CS36LI
Order Code OSA- 279-7100K
Operating Voltage 3.6V DC
Battery 1 x Lithium 3.6V
Charging Time 5-7 hours
Charger Input 230v ~ 50 Hz
Charger Output 6V 300mA
No Load Speed 180rpm
Drive 1/4” hexagon
Maximum Torque 3.5Nm (58kg/cm)
Vibration Level 0.323m/s2
Sound Power Level - LWA 62.4dBA
Sound pressure Level - LPA 51.4dBA
Net Weight Screwdriver Only 350g
60mm Magnetic
bit holder
CORDLESS SCREWDRIVER
CHARGER
DRIVER BITS
60mm Magnetic Bit Holder:
50mm Bits: 1 of each - Phillips: No.1 & 2, Pozi No.1 & 2, Slotted: 5 & 6mm.
25mm Bits: 1 of each - Hexagon: - 2, 2.5, 3, 3.5, 4, 5 & 6mm. TX: - T10, T15, T20 (x2), T27,
T30, T40 & T45. Pozi: - No. 0, 1, 2 & 3. Phillips: - No. 0, 1, 2 & 3. Slotted: - 3, 4, 5, 6 & 7mm.
25mm - 1/4” Hexagon to 1/4” Sq. Socket adaptor
1/4” Drive Sockets: 6, 7, 8, 9, 10, 11, 12 & 13mm
A comprehensive repair and service
facility is available through your
local Osaki agent.
ACCESSORIES
MAINTENANCE
SERVICE & REPAIR
THE ENVIRONMENT
Always dispose of unwanted tools, accessories and packaging materials in an environmentally
friendly manner.
After its useful working life, the Screwdriver can be easily dismantled to remove the lithium-ion
battery. The battery can then be disposed of in an approved environmental manner. To dismantle,
firstly remove the six screws holding the two enclosures together using a No.0 crosspoint
screwdriver. Disconnect the battery from the circuit by cutting the wires.
For EU and EEA countries only.
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE) and its implementation in accordance with national law, electrical goods that have reached
the end of their life must be collected separately and returned to an environmentally compatible
recycling facility.
Do not dispose of electrical goods with domestic waste materials as inappropriate disposal may
cause potential hazards to the environment and human health.
For further information, please contact your local authority or the retailer from whom you purchased
the product.
This product does not contain any restricted substances in concentrations and applications which
are banned by the European RoHS Directive.
The outer casing can be cleaned using a damp cloth and mild detergent. NEVER use solvent.
The charger can be cleaned by removing it from the mains electricity supply and then wiping dirt and
grease off using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions.
Recommended accessories for use with your Screwdriver are available at extra cost from your local Osaki
agent.
OSA-279-7100K_Instructions.qxd 22/08/2011 07:53 Page 3

OPERATION
This driver kit comes complete with 42 bits and sockets for
driving different types of screws plus a magnetic bit driver and
1/4” Sq. socket adapator. When using the 25mm bits it allows
you to get into tight places with a overall depth of 170mm. If
you need that extra reach you can add the magnetic bit holder
and the 50mm bits to give you an increased reach of 245mm,
FORWARD AND REVERSE OPERATION
Looking at the front of the driver (Fig.4), if the slide switch is
as shown, the drive shaft will rotate towards the LEFT
(Anti-clockwise/Reverse). If the opposite side, the drive shaft will
turn towards the RIGHT (Clockwise/Forward). When the slide switch
is in the central/locked position the driver will act as a torch.
MANUAL SCREWDRIVING
If the slide switch is left in the central position this locks the
spindle. With the trigger switch dis-engaged, it can be used for
manual screwdriving.
TORQUE/DRILL SETTING
The driver has seven pre-set torque settings which are useful if doing repetitive work and you need to keep
torques at a constant. It is always best to do a trial on the same materials and fixings you are using so
that the torque can be set to tighten a fixing just enough and not damage materials being fixed into. The
diffferent toques are set using the twist dial at the front of the driver as shown in Fig.5, the higher the
number, the higher the torque set.
To use as a drill you need to set the dial on the last setting as shown in Fig.6 so that the clutch
mechanism will not kick in when drilling.
INSTALLING AND REMOVING
HEXAGON BITS
The hexagon driver bits are
fitted by pushing their
hexagonal end fully into the
hexagon drive. To get the
best drive it is always best
to use the shortest bits
possible for the job you are
doing as the more
connections are involved the
looser the drive.
Locked
CHARGING
54
IMPORTANT CHARGING NOTES
To obtain a good performance, the batteries should be charged when the air temperature is between
65°F (18°C) and 75°F (24°C).
The batteries will require 5 - 10 charges/discharges before they reach full capacity.
The charger and batteries may become warm whilst charging. This is a normal condition and does not
indicate a problem.
CHARGING
1. Connect the output cord of the charger to the charging socket (See fig. 1 & 2) on the bottom of the
Screwdriver’s handle.
2. Make sure the mains electricity voltage is the same as that shown on the specification label of the
charger. Connect the plug of the charger into the mains electricity supply socket.
3. Charge for 5-7 hours then disconnect from the charger.
4. Use the battery condition indicator lights (Fig.3.) to check the battery is fully charged. When all 3 lights
(Red, Green & Yellow) are illuminated the battery is at full capacity.
5. When 2 lights (Yellow & Red) are illuminated, this indicates that the battery capacity is beginning to
diminish.
6. When only one light is illuminated (Red) it indicates that the battery capacity is low and the unit needs
to be charged.
Fig. 2
Fig. 3
Fig. 1
Fig. 4
LR
Fig. 5 Fig. 6
OSA-279-7100K_Instructions.qxd 22/08/2011 07:53 Page 4