OSD Audio XPA1000 User manual

XPA
XPA
1000
600 DIGITAL AMPLIFIER
COMMERCIAL
OWNER’S
MANUAL
XPA1000-600 Amp manual R1.indd 1 7/20/22 10:01 AM

1
INTRODUCTION
We at OSD Audio thank you for your purchase of our XPA-1000/XPA-600 featuring Energy Efcient Class D
Pure 70/100 Volt Commercial Power Ampliers.
Both these Power Ampliers are a welcome addition to our 70/100 Volt Lineup. A perfect add on to our current
PAM245 or as a stand alone product both Ampliers deliver 2 Channels of pure 70/100V power. In addition to the
great features you’ve come to expect in an OSD Audio Amplier, the XPA Ampliers feature both Unbalanced and
Balanced Line Inputs, an included IR-Remote Control, hard-wired IR Receiver module/sensor, an RS232 input for
integration with control systems in a compact 1U rack Chassis. The Class D Power Supplies are 93% Efcient.
Don’t let their compact size fool you, both ampliers double down, the XPA-1000 is 2 x 500 Watts and the
XPA 600 is 2 x 300 Watts
Inside the box:
One 70/100Volt Power Amplier
One Product Manual
One IR Remote Control/ One IR Receiver Module Sensor Kit
One set of rack mounting hardware including two (2) brackets
AC Power Cord
2
SAFETY
The lightning ash with arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of un-insulated “danger-
ous voltage” within the product’s enclosure that may be of sufcient
magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
This product was designed and manufactured to meet strict quality and safety standards. There are, however,some
installation and operation precautions, which you should be particularly aware of.
TO REDUCE THE RISK OF FIRE OR ELECTRICSHOCK,DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER ( OR BACK )
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICE TO QUALIFIED SERVICE PERSONNEL
WARNING
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on appliance and in the operating instructions should be adhered to.
4. Follow instructions - All operating and use instructions should be followed.
5. Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.
6. Carts and Stands - The appliance should be only with a cart or stand that is recommended by the manufacturer. An
appliance and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and cart combination to overturn.
XPA1000-600 Amp manual R1.indd 2-3 7/20/22 10:01 AM

1
INTRODUCTION
We at OSD Audio thank you for your purchase of our XPA-1000/XPA-600 featuring Energy Efcient Class D
Pure 70/100 Volt Commercial Power Ampliers.
Both these Power Ampliers are a welcome addition to our 70/100 Volt Lineup. A perfect add on to our current
PAM245 or as a stand alone product both Ampliers deliver 2 Channels of pure 70/100V power. In addition to the
great features you’ve come to expect in an OSD Audio Amplier, the XPA Ampliers feature both Unbalanced and
Balanced Line Inputs, an included IR-Remote Control, hard-wired IR Receiver module/sensor, an RS232 input for
integration with control systems in a compact 1U rack Chassis. The Class D Power Supplies are 93% Efcient.
Don’t let their compact size fool you, both ampliers double down, the XPA-1000 is 2 x 500 Watts and the
XPA 600 is 2 x 300 Watts
Inside the box:
One 70/100Volt Power Amplier
One Product Manual
One IR Remote Control/ One IR Receiver Module Sensor Kit
One set of rack mounting hardware including two (2) brackets
AC Power Cord
2
SAFETY
The lightning ash with arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of un-insulated “danger-
ous voltage” within the product’s enclosure that may be of sufcient
magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
This product was designed and manufactured to meet strict quality and safety standards. There are, however,some
installation and operation precautions, which you should be particularly aware of.
TO REDUCE THE RISK OF FIRE OR ELECTRICSHOCK,DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER ( OR BACK )
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICE TO QUALIFIED SERVICE PERSONNEL
WARNING
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on appliance and in the operating instructions should be adhered to.
4. Follow instructions - All operating and use instructions should be followed.
5. Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.
6. Carts and Stands - The appliance should be only with a cart or stand that is recommended by the manufacturer. An
appliance and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and cart combination to overturn.
XPA1000-600 Amp manual R1.indd 2-3 7/20/22 10:01 AM

4
FEATURES & SPECIFICATIONS
FEATURES XPA1000 XPA600
Power Output 500 Watts Per Channel 300 Watts Per Channel
Design Class D 93% Efcient
Inputs Balance and Unbalanced Inputs
Outputs Unbalanced Loop Line Output to Another Amplier
12V Trigger For Remote Turn On
12V Trigger Out to Trigger External Device
70V/100V Selectable Rear Panel Swit
IR Remote IR Remote Included/ Hard Wired IR Receiver/ Codes Availab
RS232 RS232 Querries & Commands Available
Output Level Meter Front Panel Status; Protection & Warning LEDs
Chassis Design 1U Rack
Voltage Multi-Voltage: AC115/230V
SPECIFICATIONS XPA1000 XPA600
Power Output 500W X2 300 W X2
THD 1% (Rated Power)
Signal To Noise >90dB A Weighted
Freq Response 20Hz - 22kHz +0/-2dB
Adjustable Level Min - Max
Line Level Input
Sensitivity 510mV
Thermal Protection Yes
Short Protection Yes
Dimensions (WxHxD) 435mm x 44mm x 240mm 17" x 1.7" x 9.4"
Weight 4.2Kgs / 9.25lbs
3
SAFETY
13. Cleaning – Clean only with dry cloth.
14. Power Lines – An outdoor antenna should be located away from the power lines.
15. Nonuse Periods – The power cord of the appliance should be unplugged from the outlet when left unused for a long
period of time.
16. Accessories – Only use attachments/accessories specied by the manufacturer.
17. Object and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into the enclosure
through openings.
18. Damage Requiring Service – The appliance should be serviced by qualied service Personnel when:
A. The Power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
19. Servicing – The user should not attempt to service the appliance beyond that described in the operating instructions.
All other servicing should be referred to qualied service personnel.
7. Wall or Ceiling Mounting – The appliance should be mounted to wall or ceiling only as recommended by
the manufacturer.
8. Ventilation – The appliance should be situated so that its location or position does not interfere with its proper
ventilation.For example, the appliance should not be situated on a bed, sofa, rug or similar surface that
may block the ventilation openings; or, place in a built-in installation, such as a bookcase or cabinet that
may impede the ow of air through the ventilation openings.
9. Heat – Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
( including ampliers ) that produce heat.
10. Power Sources – The appliance should be connected to a power supply only of the type described in the operation
instructions or as marked on the appliance.
11. Grounding or Polarization – Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third grounding prong are provide for your
safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
12. Power-Cord Protection – Power supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cord at plugs, convenience
receptacles, and the point where they exit from the appliance.
XPA1000-600 Amp manual R1.indd 4-5 7/20/22 10:01 AM

4
FEATURES & SPECIFICATIONS
FEATURES XPA1000 XPA600
Power Output 500 Watts Per Channel 300 Watts Per Channel
Design Class D 93% Efcient
Inputs Balance and Unbalanced Inputs
Outputs Unbalanced Loop Line Output to Another Amplier
12V Trigger For Remote Turn On
12V Trigger Out to Trigger External Device
70V/100V Selectable Rear Panel Swit
IR Remote IR Remote Included/ Hard Wired IR Receiver/ Codes Availab
RS232 RS232 Querries & Commands Available
Output Level Meter Front Panel Status; Protection & Warning LEDs
Chassis Design 1U Rack
Voltage Multi-Voltage: AC115/230V
SPECIFICATIONS XPA1000 XPA600
Power Output 500W X2 300 W X2
THD 1% (Rated Power)
Signal To Noise >90dB A Weighted
Freq Response 20Hz - 22kHz +0/-2dB
Adjustable Level Min - Max
Line Level Input
Sensitivity 510mV
Thermal Protection Yes
Short Protection Yes
Dimensions (WxHxD) 435mm x 44mm x 240mm 17" x 1.7" x 9.4"
Weight 4.2Kgs / 9.25lbs
3
SAFETY
13. Cleaning – Clean only with dry cloth.
14. Power Lines – An outdoor antenna should be located away from the power lines.
15. Nonuse Periods – The power cord of the appliance should be unplugged from the outlet when left unused for a long
period of time.
16. Accessories – Only use attachments/accessories specied by the manufacturer.
17. Object and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into the enclosure
through openings.
18. Damage Requiring Service – The appliance should be serviced by qualied service Personnel when:
A. The Power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
19. Servicing – The user should not attempt to service the appliance beyond that described in the operating instructions.
All other servicing should be referred to qualied service personnel.
7. Wall or Ceiling Mounting – The appliance should be mounted to wall or ceiling only as recommended by
the manufacturer.
8. Ventilation – The appliance should be situated so that its location or position does not interfere with its proper
ventilation.For example, the appliance should not be situated on a bed, sofa, rug or similar surface that
may block the ventilation openings; or, place in a built-in installation, such as a bookcase or cabinet that
may impede the ow of air through the ventilation openings.
9. Heat – Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
( including ampliers ) that produce heat.
10. Power Sources – The appliance should be connected to a power supply only of the type described in the operation
instructions or as marked on the appliance.
11. Grounding or Polarization – Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third grounding prong are provide for your
safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
12. Power-Cord Protection – Power supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cord at plugs, convenience
receptacles, and the point where they exit from the appliance.
XPA1000-600 Amp manual R1.indd 4-5 7/20/22 10:01 AM

The following information is provided for reference only. Please consult a professional if unsure about any
aspects of commercial or residential installations.
Speaker Connection
The rear panel of the amplier contains 2 Line Outputs (Line 1 and Line 2). BE SURE TO CONNECT SPEAKERS
PROPERLY, see line voltage instructions below. The speaker lines are to be connected directly between
the appropriate COM terminal on the terminal strip and the terminal corresponding to the impedance of the
speaker(s). Connect the cables to the terminals on the screw terminal strip provided. Use the screw terminals
which correspond to the proper polarity of the speaker(s). One lead must always be connected to the COM.
IMPORTANT NOTICE: When 70V constant line voltages are used, a line matching transformer must be used with
each speaker. All transformers must be connected in parallel.
ALWAYS CONNECT LINE TRANSFORMERS IN PARALLEL, NEVER CONNECT IN SERIES
Speaker Impedances
Speaker terminal taps for 70V constant line voltage are provided on the rear panel of the unit. To connect the
power output directly to a speaker or PA horn or a combination of speakers and/or PA horns, connect to the COM
and (+) terminal on the strip. Be sure the speaker(s) or PA horn(s) can handle a reasonable power output from
the amplier or permanent damage to the speaker(s) or PA horn(s) may result. Also, be careful not to overload
the amplier with too many speakers or PA horns. If it is desired to use a number and variety of speakers, the
speakers must be arranged in various series or parallel arrays to provide proper impedance matching. 70V
constant line voltage must be used (parallel connection only). If you are not familiar with impedance matching,
consult a professional installer or technician for advice. If 70V constant line voltages are used, a line matching
transformer must be used with each speaker. Again do not overload or use incompatible speakers. Line
transformers are the preferred method for multi-speaker installation.
Cable Requirements
Output cabling need not be shield in most case and should be of sufcient gauge to minimize losses due to the
resistance of the wire over long runs (insertion loss). Cable thinner than 18 gauge AWG is not recommended.
Long runs require 16 gauge AWG or heavier.
In some cases where the output cable is run in close proximity to unshielded intercom cables, electrical cables,
radio transmission antennas or other sources of interference, or when the amplier is being used for paging from
a telephone system, the amplier may require shielded output cabling to prevent audio feedback or interference.
WHENEVER IN DOUBT ABOUT INSTALLATION, CONSULT WITH A PROFESSIONAL INSTALLER OR
TECHNICIAN. OTHERWISE, PERSONAL INJURY, DAMAGE TO THIS AMPLIFIER AND/OR
SPEAKERS MAY RESULT AND YOUR WARRANTY MAY BE VOID.
REFERENCE INFORMATION
6
5
FRONT & REAR PANEL DESCRIPTION
100V
MADEIN CHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
44.00
434.00
丝印色： Cool Gray 2C XPA-1000
2022-07-18
100V
MADEIN CHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
UL
62368
UL
62368
1. 70/100V Selector: 70V for U.S., 100V for Europe
2. RS232 Control
3. IR Receiver Connection
4. 12V Trigger In & Out: Apply 4.5-15 Volts DC to turn Amplier On, Link other equipment connected to the 12V Out
with the same 12V signal.
5. Audio Loop Outputs: RCA Connections, unbalanced mono for sending audio from channel one (1) to channel two
(2) or output to other components.
6. Unbalanced Inputs: Unbalanced mono RCA Source inputs for Channels One (1) and Two (2)
7. Balanced Inputs Connector 3 & 4: Six Pin Set Screw connector for two Balanced Input Connections for Channels
3 and 4
8. Output Gain Controls: Ch1 & Ch2 Level control knob for Channels 1 and 2. Turn clockwise to increase and
counterclockwise to decrease output levels.
9. Speaker Output Connector: Speaker output connector with set screw for Channels one (1) and two (2)
10. Multi Voltage Selector Switch: 115V or 230V
11. IEC Power Receptacle
12. AC Fuse/Holder
1. Power Switch
2. Protection LED: Normal (Blue) Protection (Red)
3. Output Level Meter: 3 LEDs for each channel -30, -20, -10 (Flashing Blue)
Clip Indicator (Red Light) Illuminates when each channel clips.
NOTE: If clipping occurs trun the gain control down on the back of the amp.
1
1 2 3 4 5 6 7 8 9 10 11 12
2 3
XPA1000-600 Amp manual R1.indd 6-7 7/20/22 10:01 AM

The following information is provided for reference only. Please consult a professional if unsure about any
aspects of commercial or residential installations.
Speaker Connection
The rear panel of the amplier contains 2 Line Outputs (Line 1 and Line 2). BE SURE TO CONNECT SPEAKERS
PROPERLY, see line voltage instructions below. The speaker lines are to be connected directly between
the appropriate COM terminal on the terminal strip and the terminal corresponding to the impedance of the
speaker(s). Connect the cables to the terminals on the screw terminal strip provided. Use the screw terminals
which correspond to the proper polarity of the speaker(s). One lead must always be connected to the COM.
IMPORTANT NOTICE: When 70V constant line voltages are used, a line matching transformer must be used with
each speaker. All transformers must be connected in parallel.
ALWAYS CONNECT LINE TRANSFORMERS IN PARALLEL, NEVER CONNECT IN SERIES
Speaker Impedances
Speaker terminal taps for 70V constant line voltage are provided on the rear panel of the unit. To connect the
power output directly to a speaker or PA horn or a combination of speakers and/or PA horns, connect to the COM
and (+) terminal on the strip. Be sure the speaker(s) or PA horn(s) can handle a reasonable power output from
the amplier or permanent damage to the speaker(s) or PA horn(s) may result. Also, be careful not to overload
the amplier with too many speakers or PA horns. If it is desired to use a number and variety of speakers, the
speakers must be arranged in various series or parallel arrays to provide proper impedance matching. 70V
constant line voltage must be used (parallel connection only). If you are not familiar with impedance matching,
consult a professional installer or technician for advice. If 70V constant line voltages are used, a line matching
transformer must be used with each speaker. Again do not overload or use incompatible speakers. Line
transformers are the preferred method for multi-speaker installation.
Cable Requirements
Output cabling need not be shield in most case and should be of sufcient gauge to minimize losses due to the
resistance of the wire over long runs (insertion loss). Cable thinner than 18 gauge AWG is not recommended.
Long runs require 16 gauge AWG or heavier.
In some cases where the output cable is run in close proximity to unshielded intercom cables, electrical cables,
radio transmission antennas or other sources of interference, or when the amplier is being used for paging from
a telephone system, the amplier may require shielded output cabling to prevent audio feedback or interference.
WHENEVER IN DOUBT ABOUT INSTALLATION, CONSULT WITH A PROFESSIONAL INSTALLER OR
TECHNICIAN. OTHERWISE, PERSONAL INJURY, DAMAGE TO THIS AMPLIFIER AND/OR
SPEAKERS MAY RESULT AND YOUR WARRANTY MAY BE VOID.
REFERENCE INFORMATION
6
5
FRONT & REAR PANEL DESCRIPTION
100V
MADEIN CHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
44.00
434.00
丝印色： Cool Gray 2C XPA-1000
2022-07-18
100V
MADEIN CHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
UL
62368
UL
62368
1. 70/100V Selector: 70V for U.S., 100V for Europe
2. RS232 Control
3. IR Receiver Connection
4. 12V Trigger In & Out: Apply 4.5-15 Volts DC to turn Amplier On, Link other equipment connected to the 12V Out
with the same 12V signal.
5. Audio Loop Outputs: RCA Connections, unbalanced mono for sending audio from channel one (1) to channel two
(2) or output to other components.
6. Unbalanced Inputs: Unbalanced mono RCA Source inputs for Channels One (1) and Two (2)
7. Balanced Inputs Connector 3 & 4: Six Pin Set Screw connector for two Balanced Input Connections for Channels
3 and 4
8. Output Gain Controls: Ch1 & Ch2 Level control knob for Channels 1 and 2. Turn clockwise to increase and
counterclockwise to decrease output levels.
9. Speaker Output Connector: Speaker output connector with set screw for Channels one (1) and two (2)
10. Multi Voltage Selector Switch: 115V or 230V
11. IEC Power Receptacle
12. AC Fuse/Holder
1. Power Switch
2. Protection LED: Normal (Blue) Protection (Red)
3. Output Level Meter: 3 LEDs for each channel -30, -20, -10 (Flashing Blue)
Clip Indicator (Red Light) Illuminates when each channel clips.
NOTE: If clipping occurs trun the gain control down on the back of the amp.
1
1 2 3 4 5 6 7 8 9 10 11 12
2 3
XPA1000-600 Amp manual R1.indd 6-7 7/20/22 10:01 AM

Rack Mounting
The XPA-1000/600 both come with Rack Mounts in the box. Remove the two chassis
screws from each side panel, closest to the front panel Attach the rack-mount ears
to the sides of the front face plate using the screws that come with the rack mounts
(2 each side). The amplier will occupy 1U of rack space. Ensure that the unit is in a
well-ventilated area that provides adequate cooling. Free air space is required above
the amplier and below the amplier. The recommended distance is 1U to 2U, 1.75” to
3.5” being sure to avoid blocking any vents on the unit’s chassis.
Bottom feet on the amplier chassis may be removed if necessary.
NOTE: Do not place the screws back into the chassis. Without the feet, the length of
the screw may touch internal components and affect the performance of the amplier.
Balanced Input
Use the BALANCED INPUT to connect balanced or unbalanced cables to
the amplier.
NOTE: The unbalanced connection needs a jumper from the Shield to the
Negative. The unbalanced connection is used when there is no balanced
source and more additional connections to the amp are needed.
Unbalanced Connections
Use standard RCA cables to connect sources using the
UNBALANCED LINE IN input. Connect sources through the
applicable mono input. Use the LOOP OUT ports to connect
more ampliers or equipment.
Unbalanced Loop Out
1 & 2
Unbalanced Line In
1 & 2
Using Fixed Loop Out
The LOOP OUT connections on the amplier may
be used to send audio signals to other equipment, or
to the other channel of the amplier. This connection
sends audio signals out from the UNBALANCED
INPUT of the channel.
7
FEATURES AND FUNCTION
8
APPLICATION DIAGRAMS
100V
MADEINCHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
44.00
434.00
丝印色： Cool Gray 2C XPA-1000
2022-07-18
100V
MADEIN CHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
UL
62368
UL
62368
44.00
434.00
丝印色： Cool Gray 2C XPA-1000
2022-07-18
100V
MADEIN CHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
UL
62368
UL
62368
44.00
434.00
丝印色： Cool Gray 2C XPA-1000
2022-07-18
100V
MADEIN CHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
UL
62368
UL
62368
100V
70V
VCC
MADE IN CHINA
100/120V~60Hz 12A
T12AL 250V
220/240V~50Hz 6.3A
T6.3AL 250V
POWER
PROT -30 -20 -10 CLIP
1
2
XPA 500
XPA 500
100V
70V
VCC
MADE IN CHINA
100/120V~60Hz 12A
T12AL 250V
220/240V~50Hz 6.3A
T6.3AL 250V
POWER
PROT -30 -20 -10 CLIP
1
2
XPA 500
XPA 500
100V
70V
VCC
MADE IN CHINA
100/120V~60Hz 12A
T12AL 250V
220/240V~50Hz 6.3A
T6.3AL 250V
POWER
PROT -30 -20 -10 CLIP
1
2
XPA 500
XPA 500
Ch 3 Ch 4 Ch 3 Ch 4
Balanced Un-Balanced
From Source
Connect Channel 1
Loop OUT to
Channel 2 Loop
in for two channels
with one source, or
to equipment.
SOURCE
SOURCE2
Unbalanced
SOURCE1
Unbalanced
SINGLE SOURCE
Mono
CH2
Mono
Channel 2
RIGHT
Channel 2
RIGHT
Channel 1
LEFT
Channel 1
LEFT
Single Source W/ Stereo Output
Two Source W/ Two Mono Output Zones
Single Mono Source Unbalanced
Loop Out For
Additional Amp
Loop Out For
Additional Amp
Source 2 Balanced
Audio cannot be
looped out
CH1
Mono
Loop OUT Ch1
to Ch2 Input
XPA1000-600 Amp manual R1.indd 8-9 7/20/22 10:01 AM

Rack Mounting
The XPA-1000/600 both come with Rack Mounts in the box. Remove the two chassis
screws from each side panel, closest to the front panel Attach the rack-mount ears
to the sides of the front face plate using the screws that come with the rack mounts
(2 each side). The amplier will occupy 1U of rack space. Ensure that the unit is in a
well-ventilated area that provides adequate cooling. Free air space is required above
the amplier and below the amplier. The recommended distance is 1U to 2U, 1.75” to
3.5” being sure to avoid blocking any vents on the unit’s chassis.
Bottom feet on the amplier chassis may be removed if necessary.
NOTE: Do not place the screws back into the chassis. Without the feet, the length of
the screw may touch internal components and affect the performance of the amplier.
Balanced Input
Use the BALANCED INPUT to connect balanced or unbalanced cables to
the amplier.
NOTE: The unbalanced connection needs a jumper from the Shield to the
Negative. The unbalanced connection is used when there is no balanced
source and more additional connections to the amp are needed.
Unbalanced Connections
Use standard RCA cables to connect sources using the
UNBALANCED LINE IN input. Connect sources through the
applicable mono input. Use the LOOP OUT ports to connect
more ampliers or equipment.
Unbalanced Loop Out
1 & 2
Unbalanced Line In
1 & 2
Using Fixed Loop Out
The LOOP OUT connections on the amplier may
be used to send audio signals to other equipment, or
to the other channel of the amplier. This connection
sends audio signals out from the UNBALANCED
INPUT of the channel.
7
FEATURES AND FUNCTION
8
APPLICATION DIAGRAMS
100V
MADEINCHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
44.00
434.00
丝印色： Cool Gray 2C XPA-1000
2022-07-18
100V
MADEIN CHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
UL
62368
UL
62368
44.00
434.00
丝印色： Cool Gray 2C XPA-1000
2022-07-18
100V
MADEIN CHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
UL
62368
UL
62368
44.00
434.00
丝印色： Cool Gray 2C XPA-1000
2022-07-18
100V
MADEIN CHINA
70V
VCC
1000
1000
100/120V~60Hz12A
T12AL250V
220/240V~50Hz6.3A
T6.3AL250V
UL
62368
UL
62368
100V
70V
VCC
MADE IN CHINA
100/120V~60Hz 12A
T12AL 250V
220/240V~50Hz 6.3A
T6.3AL 250V
POWER
PROT -30 -20 -10 CLIP
1
2
XPA 500
XPA 500
100V
70V
VCC
MADE IN CHINA
100/120V~60Hz 12A
T12AL 250V
220/240V~50Hz 6.3A
T6.3AL 250V
POWER
PROT -30 -20 -10 CLIP
1
2
XPA 500
XPA 500
100V
70V
VCC
MADE IN CHINA
100/120V~60Hz 12A
T12AL 250V
220/240V~50Hz 6.3A
T6.3AL 250V
POWER
PROT -30 -20 -10 CLIP
1
2
XPA 500
XPA 500
Ch 3 Ch 4 Ch 3 Ch 4
Balanced Un-Balanced
From Source
Connect Channel 1
Loop OUT to
Channel 2 Loop
in for two channels
with one source, or
to equipment.
SOURCE
SOURCE2
Unbalanced
SOURCE1
Unbalanced
SINGLE SOURCE
Mono
CH2
Mono
Channel 2
RIGHT
Channel 2
RIGHT
Channel 1
LEFT
Channel 1
LEFT
Single Source W/ Stereo Output
Two Source W/ Two Mono Output Zones
Single Mono Source Unbalanced
Loop Out For
Additional Amp
Loop Out For
Additional Amp
Source 2 Balanced
Audio cannot be
looped out
CH1
Mono
Loop OUT Ch1
to Ch2 Input
XPA1000-600 Amp manual R1.indd 8-9 7/20/22 10:01 AM

9
IR REMOTE CONTROL
10
IR CODES & RS232 COMMANDS
XPA IR Remote
The XPA-1000 and XPA-600 IR Remote Controller, controls the individual zones on our PAM-1270 amplier. It can also
be used to teach IR commands to a programmable, integrated universal IR Remote, zone control system or other IR
routing device.
Both of the XPA-1000 and the XPA-600 come with a IR Receiver module that connects to
the IR two conductor input connector. There is no built in IR Sensor. The following are brief
descriptions of each button. Universal IR codes are also available on the next page of the
Owners Manual.
XPA IR Remote Universal Codes
The XPA 70V Ampliers IR Remote Controller, controls the individual Power On/Off, Source, and the Volume Levels for
Channels 1/3 & 2/4 and All Channels combined. It can also be used to teach IR commands to a programmable, integrated
universal IR Remote or other IR routing device. The following are the Remote Controller Head Code and Hex codes for
the individual buttons:
IR Remote Function
1. IR LED - One, high-output IR LED. The IR LED ashes invisible
(infrared light pulses that are the control codes for the XPA-1000
& XPA-600. The LED must be pointed at an IR receiver that is
connected to an XPA-1000/600. The IR Receiver Sensor must be
connected to the IR 2 Conductor Connector
2. Power On/Off– Separate Power On (Red Button) and Power Off.
3. Source Selects between the Unbalanced and Balanced Sources.
4. Ch1 Vol+, Vol- & Mute – CH1-Unbalanced/CH3-Balanced;
Volume Up. CH1-Unbalanced/CH3-Balanced and Mute for CH1 and
CH3.
5. Ch2 Vol+, Vol- & Mute – CH2-Unbalanced/CH4-Balanced;
Volume Up. CH2-Unbalanced/CH4-Balanced and Mute for CH2 and
CH4.
6. All Channels Vol+, Vol- & Mute – All Channels-Unbalanced/
Balanced; Volume Up. All Channels-Unbalanced/Balanced and
Mute for All Channels.
100V
70V
VCC
MADE IN CHINA
100/120V~60Hz 12A
T12AL 250V
220/240V~50Hz 6.3A
T6.3AL 250V
POWER
PROT -30 -20 -10 CLIP
1
2
XPA 500
XPA 500
POWER
ON
CH1
VOL+
CH1
VOL-
POWER
OFF
SOURCE
MUTE
CH1
VOL+
CH1
VOL- MUTE
ALL
VOL+
ALL
VOL- MUTE
K1 K2
K4 K6K5
K7 K9K8
K10 K12K11
K3
1
2
3
4
5
6
XPA1000/XPA600 Remote Controller Head Code: 00FF
Function Key Keys Code Remark
Power On K1 45 power turn amplier on
Power Off K2 47 power turn amplier off
Source K3 43 RCA Balance/UnBalanced Inpus select
CH1 VOL + K4 16 CH1/CH3 VOL UP
CH1 VOL - K5 19 CH1/CH3 VOL DOWN
MUTE K6 OD CH1/CH3 Silence audio on amp
CH2 Vol + K7 OC CH2/CH34 VOL UP
CH2 Vol - K8 18 CH2/CH34 VOL DOWN
MUTE K9 5E CH2/CH4 Silence audio on amp
All VOL + K10 O8 CH1+CH2 and CH3/CH4 VOL UP
All VOL - K11 1C CH1+CH2 and CH3/CH4 VOL DOWN
MUTE K12 5A CH1+CH2 and CH3+CH4 Silence audio on amp
XPA1000/XPA600 RS232 Commands
Sequence # Name Command Remark
1<CR>: Enter Key
2<Esc>: Escape Key
3<Spaec>: Space Key
4Nov<CR> Show All PA Status:
5Power<Space>On<CR> Power On Power On/Off Control:
6Power<Space>Off<CR> Power Off Power On/Off Control:
7Power<Space>Toggle<CR> Power Toggle Control Power On/Off Control
8Source<Space>1<CR> RCA (Unbalanced Inputs) Source Control:
9Source<Space>2<CR> Balanced Inputs Source Control:
10 Volume<Space>xx<CR> Volume xx (xx range 00-63) Total Volume Control: 00 to MIN; 63 to MAX
11 Volume<Space>01<CR> Setting Volume as 01 level Total Volume Control
12 Mute<Space> On<CR> Mute On RCA (Unbalanced/balanced inputs) Mute Control
13 Mute<Space>Off<CR> Mute Off RCA (Unbalanced/balanced inputs) Mute Control
14 Mute<Space>Toggle<CR> Mute Toggle Control Mute On/Off Control
15 Ch1 Mute On/Off/Toggle Ch1 Mute On/Ch1 Mute Off/Ch1 Toggle Ch1/Ch3 Mute Control
16 Ch2 Mute On/Off/Toggle Ch2 Mute On/Ch2 Mute Off/Ch2 Toggle Ch2/Ch4 Mute Control
17 Attenuator xx(00-31) Ch1 Ch2 Vol Total Attenuator
18 Ch1 Attenuator xx(00-31) Ch1 Vol(xx range 00-31) Ch1 Volume Attenuator
19 Ch2 Attenuator xx(00-31) Ch2 Vol(xx range 00-31) Ch2 Volume Attenuator
20 Save<CR> Store all current setting w/out power on/off status
XPA1000-600 Amp manual R1.indd 10-11 7/20/22 10:01 AM

9
IR REMOTE CONTROL
10
IR CODES & RS232 COMMANDS
XPA IR Remote
The XPA-1000 and XPA-600 IR Remote Controller, controls the individual zones on our PAM-1270 amplier. It can also
be used to teach IR commands to a programmable, integrated universal IR Remote, zone control system or other IR
routing device.
Both of the XPA-1000 and the XPA-600 come with a IR Receiver module that connects to
the IR two conductor input connector. There is no built in IR Sensor. The following are brief
descriptions of each button. Universal IR codes are also available on the next page of the
Owners Manual.
XPA IR Remote Universal Codes
The XPA 70V Ampliers IR Remote Controller, controls the individual Power On/Off, Source, and the Volume Levels for
Channels 1/3 & 2/4 and All Channels combined. It can also be used to teach IR commands to a programmable, integrated
universal IR Remote or other IR routing device. The following are the Remote Controller Head Code and Hex codes for
the individual buttons:
IR Remote Function
1. IR LED - One, high-output IR LED. The IR LED ashes invisible
(infrared light pulses that are the control codes for the XPA-1000
& XPA-600. The LED must be pointed at an IR receiver that is
connected to an XPA-1000/600. The IR Receiver Sensor must be
connected to the IR 2 Conductor Connector
2. Power On/Off– Separate Power On (Red Button) and Power Off.
3. Source Selects between the Unbalanced and Balanced Sources.
4. Ch1 Vol+, Vol- & Mute – CH1-Unbalanced/CH3-Balanced;
Volume Up. CH1-Unbalanced/CH3-Balanced and Mute for CH1 and
CH3.
5. Ch2 Vol+, Vol- & Mute – CH2-Unbalanced/CH4-Balanced;
Volume Up. CH2-Unbalanced/CH4-Balanced and Mute for CH2 and
CH4.
6. All Channels Vol+, Vol- & Mute – All Channels-Unbalanced/
Balanced; Volume Up. All Channels-Unbalanced/Balanced and
Mute for All Channels.
100V
70V
VCC
MADE IN CHINA
100/120V~60Hz 12A
T12AL 250V
220/240V~50Hz 6.3A
T6.3AL 250V
POWER
PROT -30 -20 -10 CLIP
1
2
XPA 500
XPA 500
POWER
ON
CH1
VOL+
CH1
VOL-
POWER
OFF
SOURCE
MUTE
CH1
VOL+
CH1
VOL- MUTE
ALL
VOL+
ALL
VOL- MUTE
K1 K2
K4 K6K5
K7 K9K8
K10 K12K11
K3
1
2
3
4
5
6
XPA1000/XPA600 Remote Controller Head Code: 00FF
Function Key Keys Code Remark
Power On K1 45 power turn amplier on
Power Off K2 47 power turn amplier off
Source K3 43 RCA Balance/UnBalanced Inpus select
CH1 VOL + K4 16 CH1/CH3 VOL UP
CH1 VOL - K5 19 CH1/CH3 VOL DOWN
MUTE K6 OD CH1/CH3 Silence audio on amp
CH2 Vol + K7 OC CH2/CH34 VOL UP
CH2 Vol - K8 18 CH2/CH34 VOL DOWN
MUTE K9 5E CH2/CH4 Silence audio on amp
All VOL + K10 O8 CH1+CH2 and CH3/CH4 VOL UP
All VOL - K11 1C CH1+CH2 and CH3/CH4 VOL DOWN
MUTE K12 5A CH1+CH2 and CH3+CH4 Silence audio on amp
XPA1000/XPA600 RS232 Commands
Sequence # Name Command Remark
1<CR>: Enter Key
2<Esc>: Escape Key
3<Spaec>: Space Key
4Nov<CR> Show All PA Status:
5Power<Space>On<CR> Power On Power On/Off Control:
6Power<Space>Off<CR> Power Off Power On/Off Control:
7Power<Space>Toggle<CR> Power Toggle Control Power On/Off Control
8Source<Space>1<CR> RCA (Unbalanced Inputs) Source Control:
9Source<Space>2<CR> Balanced Inputs Source Control:
10 Volume<Space>xx<CR> Volume xx (xx range 00-63) Total Volume Control: 00 to MIN; 63 to MAX
11 Volume<Space>01<CR> Setting Volume as 01 level Total Volume Control
12 Mute<Space> On<CR> Mute On RCA (Unbalanced/balanced inputs) Mute Control
13 Mute<Space>Off<CR> Mute Off RCA (Unbalanced/balanced inputs) Mute Control
14 Mute<Space>Toggle<CR> Mute Toggle Control Mute On/Off Control
15 Ch1 Mute On/Off/Toggle Ch1 Mute On/Ch1 Mute Off/Ch1 Toggle Ch1/Ch3 Mute Control
16 Ch2 Mute On/Off/Toggle Ch2 Mute On/Ch2 Mute Off/Ch2 Toggle Ch2/Ch4 Mute Control
17 Attenuator xx(00-31) Ch1 Ch2 Vol Total Attenuator
18 Ch1 Attenuator xx(00-31) Ch1 Vol(xx range 00-31) Ch1 Volume Attenuator
19 Ch2 Attenuator xx(00-31) Ch2 Vol(xx range 00-31) Ch2 Volume Attenuator
20 Save<CR> Store all current setting w/out power on/off status
XPA1000-600 Amp manual R1.indd 10-11 7/20/22 10:01 AM