OSD Audio HD-706 Installation guide

GSPECIFICATIONS With Intelligent BLC
୔
ITEM HD-706
Image Pick-Up Device
Effective Pixels
Scanning Frequency
Scanning System
Lens
Resolution
Min. Illumination
S/N Ratio
White Balance
Gamma Characteristic
Video Output
Erectronic Shutter Speed
OSD
BLC
AGC
Day&Night (Color / BW)
Display Adjust
Privacy
Power Supply
Power Consumption
Operational Temp.
Storage Temp.
Size
1/3" Sony Super HAD CCD
752(H) x 582(V)
15.625KHz(H) / 50.00KHz(V)
2:1 Interlace
Board Lens: 3.6mm/F2
560TV Lines
0.1 Lux
More than 50dB
ATW / AWB / FIXED / MANUAL
Internal / Line Lock selectable
CVBS : 1.0Vp-p75ohm
Auto / Manual (1/60sec~1/100,000sec) Auto / Manual (1/50sec~1/100,000sec)
Built-In
ON / OFF
ON / OFF
Color / Auto / BW
Contrast / Sharpness / CB-Gain / CR-Gain
ON / OFF(4 Programmable Zone)
DC12V
85mA
-10 to 50ȋC., RH 95% Max.
-20 to 60ȋC., RH 95% Max.
Approx 150g. Ø100mmX60mm
CAMERA ADJUSTMENT
SETTINGS
Settings can be made using the OSD button
located on the rear of the camera.
OSD CONTROL BOARD
LENS
SHUTTER
BLC
AGC
WHITE BAL.
FUNCTION
ADJUST
EXIT
MANUAL
AUTO
ON
ON
ATW
OSD
RETURN
CAMERA ID
MIRROR
DAY NIGHT
MOTION
PRIVACY
GAMMA
LANGUAGE
RESET
ON
OFF
COLOR
OFF
OFF
0.45
ENGLISH
OSD-FUNCTION
- Connect Video & Power Line
(DC12V Regulated Power)
- Please set the position where you want to
connect the camera.
- Loosen the locking screws and adjusting
camera angle.
-
Combine each camera parts and lock & tight
the each locking screws.
HOW TO INSTALL
INSTALLATION
Dimension & Cable Connection
OPTION: Wall Bracket DB100
Power Jack Video Jack
Power(+)
Power(
- )
Video Signal
Video GND
Cable Connection
Power Jack
(DC12V)
Video Jack
OSD Hi-Resolution Dome
Color Camera HD-706

GEASY QUICK MANUAL TO SET UP THE OSD MENU
FUNCTION
RETURN
CAMERA ID
MIRROR
DAY & NIGHT
MOTION
PRIVACY
GAMMA
RESET
FUNCTION ON
OFF
This can adjusted when privacy on.
Area can be selected up to 4 sectors
which you want to select. Area set up
value can be changed. Privacy area
color can change up to 15 color
PRIVACY AREA
AREA SEL
AREA STATE
LEFT
RIGHT
TOP
BOTTON
COLOR
RETURN
AREA0~3
ON/OFF
0~255
0~255
0~255
0~255
0~15
GAMMA USER'S CONTROL(0.00~1.00)
Move the cursor and enter the button
Appears yes/no on screen. If you select
"YES" all data will be return to factory
default.
ADJUST
SAREA STATE
SHARPNESS
CB-GAIN
CR-GAIN
RETURN
0~255
0~255
0~255
0~255
0~255
RESET YES/NO
EXIT
After set up the camera, move to exit
and enter the button to exit.
ADJUST
BLC SET UP
BLC AREA
BLC RATIO
RETURN
0~63
ADJUSTMENT WHEN "BLC" ON
ADJUST
SELECTION OF SENSING AREA
SET UP
LENS
SHUTTER
BLC
AGC
WHITE BAL.
FUNCTION
ADJUST
EXIT
MANUAL
AUTO
ON
ON
ATW
BLC AREA
ALL CLEAR
ALL SET
RETURN
EXIT
SELECTION OF SENSING AREA
BLC SET UP
BLC RATIO
RETURN
0~255
LENS DC
BRIGHTNESS
RETURN
0~255
SHUTTER FIXED
MANUAL
AUTO
FLK
LENS MANUAL
VIDEO
DC
BLC ON
OFF
AGC ON
OFF
୔When DC/VIDEO Lens selecrted,
you must select "FLXED" When you
use manual lens, you MUST select "AUTO"
Η
Θ
GEASY QUICK MANUAL TO SET UP THE OSD MENU
FUNCTION
RETURN
CAMERA ID
MIRROR
DAY & NIGHT
MOTION
PRIVACY
GAMMA
RESET
Camera ID can enter up to 15 characters
by using of button on the back pannel.
Select the position at which camera tittle
will be located. Press enter button to
exit after set up.
After up the motion, enter the button for a
second and below screen appears
FUNCTION
Ι
After setup the blc sensing area, enter
the button for second and below picture
will appear on the screen
WHITE BAL. ATW
AWB
FIXED
MANUAL
AWB MANUAL
RED
BLUE
EXIT
0~255
0~255
ADJUSTMENT IN MANUAL
ID SET UP
CAMERA ID
ซ
POSITION
RETURN
DAY & NIGHT COLOR
AUTO
B/W
MIRROR ON
OFF
MIRROR
DAY &NIGHT AUTO
DELAY
START LEVEL
END LEVEL
RETURN
0~255
0~255
0~255
CONTROL ON AUTO
ADJUSTMENT OF MOTION AREA
MOTION AREA
ALL CLEAR
ALL SET
RETURN
EXIT
FUNTION
RETURN
CAMERA ID
MIRROR
DAY & NIGHT
MOTION
PRIVACY
GAMMA
RESET
ΚMOTION ON
OFF
AWB MANUAL
AREA
MOTION TH.
MOTION TRACE
RETURN
0~255
OFF
ADJUSTMENT WHEN "MOTION" ON