OSEE HMV160 User manual

HMV160 High-definition
Multi-viewer Display Processor
USER MANUAL

Product Information
Model: HMV160 High-definition Multi-viewer Display Processor
Version: V010001
Release Date: January 1st, 2011
Company
OSEE TECHNOLOGY CO., LTD.
Contact Information
Address: No.22 Building, No.68 zone, Beiqing Road, Haidian District,
Beijing, China
Post Code: 100094
Tel: [phone]
Fax: [phone]
Web: http://www.osee-dig.com/
E-mail: [email protected]

Contents
Chapter 1 HMV160 Main Unit........................................................................................... 1
1.1 Introduction................................................................................................................................ 1
1.2 Features....................................................................................................................................... 1
1.3 Function Block Diagram............................................................................................................ 3
1.4 Frame Introduction.................................................................................................................... 3
Front panel................................................................................................................................ 4
Rear panel................................................................................................................................. 4
Chapter 2 Installation.......................................................................................................... 5
2.1 Maximum Power Ratings for Frame........................................................................................ 5
2.2 Unpacking the Module............................................................................................................... 5
2.2.1 Check the Packing List................................................................................................... 5
2.2.2 Preparing the Product for Installation.......................................................................... 5
2.3 Installing the Power Supply Module ........................................................................................ 5
2.4 Rack Installation........................................................................................................................ 6
2.5 Installing the Board Module ..................................................................................................... 6
2.6 Making the Connections............................................................................................................ 7
2.7 Removing the Board Module .................................................................................................... 7
2.8 Remove the Power Supply Module........................................................................................... 8
Chapter 3 Signal and Control Connections....................................................................... 9
3.1 Rear panel of HMV160.............................................................................................................. 9
3.2 Introduction of HMV160 Board Series.................................................................................... 9
3.3 Signal Connection Instruction of HMV160 Board Series..................................................... 10
3.3.1 Main board .................................................................................................................... 10
3.3.2 Model of Back Connector: HMV160-I4A8G8 and HMV160-I4AOG16T ............... 10
3.3.3 Model of Back Connector: HMV160-I4O1E.............................................................. 12
3.3.4 Model of Back Connector: HMV160-I4O2E.............................................................. 12
Chapter 4 Operation Instruction...................................................................................... 13
Chapter 5 LED Indicators................................................................................................. 13
Chapter 6 Dimensions........................................................................................................ 14
Chapter 7 Specification ..................................................................................................... 15
7.1 The Input and Output Connectors......................................................................................... 15
7.2 Analog Composite Input.......................................................................................................... 16
7.3 HD-SDI Digital Video Input.................................................................................................... 16
7.4 SD-SDI Digital Video Input..................................................................................................... 16
7.5 Analog Audio Input.................................................................................................................. 16
7.6 The Frame................................................................................................................................. 17

HMV160 High-definition Multi-viewer Display Processor User Manual
-1 -
HMV160 High-definition Multi-viewer Display Processor
Chapter 1 HMV160 Main Unit
1.1 Introduction
HMV160 High-definition Multi-viewer Display Processor is the specialized high-end image
processing equipment, which can simultaneously display multiple dynamic images on one single high
resolution output display.
It is designed for the occasions that need the high-quality and multiple video screen display.
HMV160 provides the ideal and practical solution for the occasions of command centre, video
conference, multimedia and multi-function hall.
HMV160 is based on module structure, and can be flexibly configured. One frame can be equipped
with many groups of multi-image system. It supports up to 64 pieces of images display.
1RU Frame: For the maximum, it supports 16 channel inputs and 4 channel outputs.
3RU Frame: For the maximum, it supports 64 channel inputs and 32 channel outputs.
HMV160 supports multiple input/output formats. For video input signal, it supports analog
composite, SD-SDI and HD- SDI video signal. For video output signal, It supports VGA, DVI，HDMI
video signal. For audio signal, it supports embedded audio and analog audio monitoring, and can display
multiple audio display windows. Moreover, it supports LTC input, and equips with GPIO port, which
can be flexibly configured.
HMV160 supports circle clock, digital time and digital date. It also supports timer up and timer
down. Furthermore, it can display image files.
Compared to the traditional upper computer control system, the HMV160 control system provides
users with more flexible and practical settings. Application of the embedded system, it realizes more
user-friendly interface. The user can set the board parameters via the mouse and keyboard.
The unit supports user-definable function of hardware and software. Support Ethernet control.
Support flexible setups of alarm, time code, GPIO and so on.
According to the needs of user, HMV160 can group different scales of display system to meet the
occasions of different monitoring scale and different applications. The multiple-in-one mode makes the
user to monitor multiple signals on one output display in real time. The user can send any signal to any
display, in any position and scale, without the restriction of the signal source grouping.
1.2 Features
Any combination of auto sense HD-SDI/ SD-SDI /Composite.
Signal path based on operation system for 24/7 mission critical application.
The user can send any signal to any display, in any position and scale, without the restriction of the
signal source grouping.
The maximum resolution of output display is wuxga：1920*1200.
Support 1080P50 output format for 50Hz input signal application.

HMV160 High-definition Multi-viewer Display Processor User Manual
-2 -
Strong signal monitoring function. Support multiple outputs in single frame; Support up to 64
pieces of images display. Simple windows setup and control via mouse.
Supporting analog audio input. Supporting the stereo audio monitoring of embedded audio and
external audio.
Up to 8 audio meter display per window.
Supporting multiple audio display windows for audio monitoring only.
16:9/4:3 aspect, various marker supported.
Supporting the Ethernet control.
Image files display supported.
Embedded TC code display supported.
Multiple analog clock and/or digital clock.
Supporting timer up and timer down.
Supporting user-definable function of hardware and software.
Supporting flexible time code setup. Supporting GPIO port with flexible configuration.
Supporting video and audio alarming. Supporting flexible alarm setup.
The board modules are hot-swappable.
Dual power supply for 1RU and 3RU frame.
The excellent cooling system effectively reduces the temperature of the frame.
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

HMV160 High-definition Multi-viewer Display Processor User Manual
-3 -
1.3 Function Block Diagram
Figure 1-1 HMV160 System Diagram
1.4 Frame Introduction
Model Appearance Description
HMV160-FR1 1RU Frame
The 1RU main processor of HMV160 can house up to 4 modules, dual power
supply and air cooling system.
HMV160-FR3 3RU Frame
The 3RU main processor of HMV160 can house up to 16 modules, dual power
supply and air cooling system.

HMV160 High-definition Multi-viewer Display Processor User Manual
-4 -
Front panel
1 2 3 1
Fig.1-2 the front panel of HMV160
The description of front panel is as follows:
1：Dual orientation locks.
2：They are the indicators lamps of power supply and fan.
PS1、PS2: the indicators lamps of dual power supply;
FAN：the indicator lamp of fan.
3：The fan and air vents
Rear panel
For the HMV160-FR3 frame, it includes two power connectors and can house up to 16 modules. For
the connecting descriptions, please refer to the following sections.
Fig.1-3 the rear panel of HMV160
Slot No. 01
Slot No.16 Blind Flange
Back connector Power Supply
Air ventAir vent

HMV160 High-definition Multi-viewer Display Processor User Manual
-5 -
Chapter 2 Installation
2.1 Maximum Power Ratings for Frame
Tab. 2-1 Maximum Power Consumption
Frame Maximum Voltage Redundant Power Supplies Numbers of Slots
HMV160-FR3 480W Yes 16
2.2 Unpacking the Module
2.2.1 Check the Packing List
The packing list includes one or more models of HMV160 unit, user manual, warranty card and the
other accessories.
2.2.2 Preparing the Product for Installation
Check the packing list. Contact your dealer right now if any items are missing.
Follow the procedures below before installing the module:
Check the equipment for any damage that may have occurred during transit.
Confirm all the items listed on the packing list have been received.
Remove all the packing material including electrostatic-resistant packing.
Retain these packing for future use.
2.3 Installing the Power Supply Module
The HMV160 equips with two power supply modules.
Follow the procedures below before installing the power supply module:
1. Make sure the frame stands firmly, and then unpack the fan section of the front panel.(For the
operation, please refer to the description of section 2.5 Step 1)
2. As shown below, on both sides of the front panel, make sure the power connector is installed
toward inside with the swivel handle of the fan side downward. And then push gently the
power supply module into the frame along the slot out of frame.
3. Make sure the power supply module has been pushed inside completely, and the power
connector rightly corresponds to the power hole of the frame. Fasten the screws under the
power connector to fix the module.

HMV160 High-definition Multi-viewer Display Processor User Manual
-6 -
2.4 Rack Installation
Install the frame to the rack.
Via the ear holder on both sides of the frame, install the HMV160 frame into a standard 19” rack,
using the proper screws and washers, which are not included in the packing list.
For proper ventilation, make sure the air vents of the side panel and top panel are not blocked.
2.5 Installing the Board Module
Caution：Static electricity may cause sensitive semiconductor out of order. Avoid installing
or removing the module in the electrostatic-induced environment.
Follow the next steps to install the module:
Step 1: Open the front panel of the frame, as shown below:
In order to open the front panel, firstly push the two orientation locks inward, as shown
below.
Secondly pull it out to remove the fan section, as shown below.
Step 2: Locate the position for back connector and insert the back connector.

HMV160 High-definition Multi-viewer Display Processor User Manual
-7 -
Step3: Fasten the screws to fix the back connector.
Step4: Locate the slot for module.
Step 5: Get the module installed in the slot, push the module slightly along the slot, press module
again to confirm that the module is installed firmly and then close swivel handle.
Step6: Install the front panel.
Fig. 2-1 Installation of 3RU Frame of HMV160 Series
2.6 Making the Connections
Please connect signals based on chapter 3.
Notes: while connecting the cables, please pay attention to the cable weighs so as to avoid the damage to
the back connector.
2.7 Removing the Board Module
Follow the following steps to remove board module:

HMV160 High-definition Multi-viewer Display Processor User Manual
-8 -
1. Open the front panel.
2. Press the swivel handle of the main board.
3. First make sure that the frame stands firmly, and then gently pull the module along the slot out
of frame.
4. Install the front panel.
5. Loosen the screws of back connector, and remove the back connector.
6. Install the Blind Flange.
Notes:
1. When the power is turned on, do not remove the front panel too long. If the user must remove
the front panel for a long time, please make disconnect the power supply.
2. Do not block any ventilation openings.
3. If the user needs to remove the back connector, please install the Blind Flange.
If there is no Blind Flange, please do not remove back connector.
4. Please do not remove the back connector when the power is turned on.
2.8 Remove the Power Supply Module
There are two power supply modules in the HMV160. Please refer to the following methods to
remove the power supply module.
a) Cut off the power supply.
b) Disconnect the power cord, and remove the screw under the power connector.
c) Make sure that the frame stands firmly, and then gently pull the power supply module along
the slot out of frame.

HMV160 High-definition Multi-viewer Display Processor User Manual
-9 -
Chapter 3 Signal and Control Connections
HMV160 Processor: The 3RU main processor of HMV160 equips with dual power supply,
multiple input boards, output boards, and so on.
The internal bus is used to connect the processing module and the power supply. All modules are
fixed in the 3RU frame. Every processing module works with the corresponding back connector.
3.1 Rear panel of HMV160
Fig.3-1 the rear panel of HMV160
1. Power input connector
2. Video input connector （BNC）
3. GPIO connector (DB26)
Stereo input /output connector (DB26)
LTC input connector (DB26)
4. HDMI output connector
5. DVI/VGA output connector（DVI-I）
6. Ethernet port（RJ45）：10M/100M autosensing.
3.2 Introduction of HMV160 Board Series
Board model Appearance Description
HMV160-I4A8G8 Board
4-Ch autosensing inputs on HD/SD/Composite (BNC);
1DB26 connector, which includes 8 Stereo audio inputs
and 8 GPI/O.
HMV160-I4AOG16T Board
4-Ch autosensing inputs on HD/SD/Composite (BNC);
1DB26 connector, which includes 1 Stereo audio
output, 16 GPI/O and 1 LTC input.

HMV160 High-definition Multi-viewer Display Processor User Manual
-10 -
Board model Appearance Description
HMV160-I4O1E Board
4-Ch autosensing inputs on HD/SD/Composite (BNC);
1-Ch DVI +1 Ch VGA output (DVI-I); dual discrete
video outputs;
1-Ch 10M/100M autosensing Ethernet port.
HMV160-I4O2E Board
4-Ch autosensing inputs on HD/SD/Composite (BNC);
2-Ch HDMI outputs (HDMI); dual discrete video
outputs;
1-Ch 10M/100M autosensing Ethernet port.
3.3 Signal Connection Instruction of HMV160 Board Series
3.3.1 Main board
Fig.3-2 Input main board
Fig.3-3 Output main board
3.3.2 Model of Back Connector: HMV160-I4A8G8 and HMV160-I4AOG16T
Fig.3-4 Back connector 1
1. IN1～IN4 Connectors
Used for HD-SDI/ SD-SDI /Composite video and embedded audio input.
2. GPIO/AUDIO/LTC Connector

HMV160 High-definition Multi-viewer Display Processor User Manual
-11 -
Fig.3-5 DB26 connector（mail）
For board model：HMV160-I4A8G8
AIN01～AIN16:Analog audio input connector from No.1 to No.16.
GPIO17～GPIO24:GPIO connector from No.1 to No.8.
Used as GPI or GPO, it can be flexibly configured.
Table Description of DB26 PIN (For board model：HMV160-I4A8G8)
PIN Signal Name Description PIN Signal Name Description
1 AIN01 Analog audio
Input 1 14 AIN14 Analog audioInput14
10 AIN02 Analog audio
Input 2 23 AIN15 Analog audio
Input15
19 AIN03 Analog audio
Input 3 6 AIN16 Analog audio
Input16
2 AIN04 Analog audio
Input4 7 GPIO17 GPI or GPO
11 AIN05 Analog audio
Input5 16 GPIO18 GPI or GPO
20 AIN06 Analog audio
Input6 25 GPIO19 GPI or GPO
3 AIN07 Analog audio
Input7 8 GPIO20 GPI or GPO
12 AIN08 Analog audio
Input8 17 GPIO21 GPI or GPO
21 AIN09 Analog audio
Input9 26 GPIO22 GPI or GPO
4 AIN10 Analog audio
Input10 9 GPIO23 GPI or GPO
13 AIN11 Analog audio
Input11 18 GPIO24 GPI or GPO
22 AIN12 Analog audio
Input12 15 GROUND
5 AIN13 Analog audio
Input13 24 GROUND
For board model: HMV160-I4AOG16T
GPIO01～GPIO16: GPIO ports, which can be flexibly configured
GPIO18: Left audio channel output of the monitored audio.

HMV160 High-definition Multi-viewer Display Processor User Manual
-12 -
GPIO22: Right audio channel output of the monitored audio.
GPIO17: LTC input. For the LTC input connector, it is the Time Code input, which
makes the internal time be synchronized with the system time. The LTC must
comply with the standard of SMPTE12M (EBU-3259-E).
GPIO19: Serial interface TXD+
GPIO23: Serial interface TXD-
GPIO20: Serial interface RXD+
GPIO24: Serial interface RXD-
Table Description of DB26 PIN (For board model：HMV160-I4AOG16T)
PIN Signal Name Description PIN Signal Name Description
1 GPIO01 GPI or GPO 14 GPIO14 GPI or GPO
10 GPIO02 GPI or GPO 23 GPIO15 GPI or GPO
19 GPIO03 GPI or GPO 6 GPIO16 GPI or GPO
2 GPIO04 GPI or GPO 7 GPIO17 LTC input
11 GPIO05 GPI or GPO 16 GPIO18 Left audio channel output of
the monitored audio
20 GPIO06 GPI or GPO 26 GPIO22 Right audio channel output
of the monitored audio
3 GPIO07 GPI or GPO 25 GPIO19 Serial interface TXD+
12 GPIO08 GPI or GPO 9 GPIO23 Serial interface TXD-
21 GPIO09 GPI or GPO 8 GPIO20 Serial interface RXD+
4 GPIO10 GPI or GPO 18 GPIO24 Serial interface RXD-
13 GPIO11 GPI or GPO 17 GPIO21
22 GPIO12 GPI or GPO 15 GROUND
5 GPIO13 GPI or GPO 24 GROUND
3.3.3 Model of Back Connector: HMV160-I4O1E
Fig.3-6 Back connector 2
IN1～IN4 Connectors
Used for HD-SDI/ SD-SDI /Composite video and embedded audio input.
Ethernet port（RJ45）
The Ethernet port is 10M/100M autosensing, and used with the control software.
Please refer to the user manual of control software for the details.
DVI/VGA Connector
1 channel DVI +1 channel VGA output (DVI-I); dual discrete video outputs.
3.3.4 Model of Back Connector: HMV160-I4O2E

HMV160 High-definition Multi-viewer Display Processor User Manual
-13 -
Fig.3-7 Back connector 3
IN1～IN4 Connectors
Used for HD-SDI/ SD-SDI /Composite video and embedded audio input.
Ethernet port（RJ45）
The Ethernet port is 10M/100M autosensing, and used with the control software.
Please refer to the user manual of control software for the details.
HDMI1、HDMI2 Connector
1 channel DVI +1 channel VGA output (DVI-I); dual discrete video outputs.
2 channels HDMI outputs (HDMI); dual discrete video outputs;
Chapter 4 Operation Instruction
The HMV160 is used with the control software.
The whole process is finished under the control of system control software. HMV160 control software is
divided into two parts.
One part is installed in the embedded processor. It is used to control HMV160 main processor to
process and integrate with information of various signal source.
The other is installed in the remote computer. It is used to control HMV160 main processor to
change the display mode in real time.
HMV160 combines information of multiple sources together, and make them become one signal string
which can display on a screen.
The HMV160 also provides the editing software. For HMV160 main processor, it can set the parameters
of display window quantity, window size, window location, program name, audio source selection,
audio source display mode, clock, and so on. The editing software can download the set parameters to
the main processor for preservation or real-time use.
For the detailed operation instruction of remote control software and editing software, please refer to the
HMV160 Control Software User Manual.
Chapter 5 LED Indicators
There are three LED indicators on the front of the panel.
Indicators Description
PS1、PS2 The indicators lamps of dual power supply.
Green: the power supply works normally;
Red: the power supply errors.
FAN The indicator lamp of fan.
Green: the fan works normally;
Red: the fan errors.

HMV160 High-definition Multi-viewer Display Processor User Manual
-14 -
Chapter 6 Dimensions
Front View （Unit: mm）
Rear View （Unit: mm ）
Top Side View （Unit: mm）

HMV160 High-definition Multi-viewer Display Processor User Manual
-15 -
Chapter 7 Specification
7.1 The Input and Output Connectors
Board model Description
HMV160-I4A8G8 4-Ch autosensing inputs on HD/SD/Composite (BNC);
8 Stereo audio inputs (DB26); 8 GPI/O (DB26).
HMV160-I4AOG16T 4-Ch autosensing inputs on HD/SD/Composite (BNC);
1 Stereo audio output (DB26); 16 GPI/O (DB26); 1 LTC input (DB26).
HMV160-I4O1E
4-Ch autosensing inputs on HD/SD/Composite (BNC);
1-Ch DVI +1 Ch VGA output (DVI-I);
1-Ch 10M/100M autosensing Ethernet port.

HMV160 High-definition Multi-viewer Display Processor User Manual
-16 -
Board model Description
HMV160-I4O2E
4-Ch autosensing inputs on HD/SD/Composite (BNC);
2-Ch HDMI outputs (HDMI);
1-Ch 10M/100M autosensing Ethernet port.
7.2 Analog Composite Input
Standard：PAL 、NTSC
Impedance: 75Ω
Return Loss：35 dB to 5.75 MHz
Connector: BNC
7.3 HD-SDI Digital Video Input
Standard: SDI1080i50, SDI1080i60, SDI1080sf24, SDI1080p24, SDI1080p25,
SDI1080p30, SDI1080p50, SDI1080p60, SDI720p24, SDI720p25, SDI720p30,
SDI720p50, SDI720p60, SDI1035i60
Impedance: 75Ω
Cable Length: 100 m （Belden 8281）
Return Loss: > 15 dB (5 MHz to 750 MHz)
> 10 dB (750 MHz to 1.5GHz)
Connector: BNC
7.4 SD-SDI Digital Video Input
Standard: SDI525I, SDI625I
Impedance: 75Ω
Cable Length: 100 m （Belden 8281）
Return Loss: > 15 dB to 270 MHz
Connector: BNC
7.5 Analog Audio Input
Standard: 8-channel balanced stereo analog audio or 16-channel balanced
monophonic analog audio
Impedance: 20KΩbalanced, 10KΩsingle ended,
Peak Ballistic: Rise Time: 10 ms; Fall Time: -20dB/s
VU Ballistic: 300ms
Scales：0to-72dB
MaximumLevel: +24dBu
Connector：DB26（male）

HMV160 High-definition Multi-viewer Display Processor User Manual
-17 -
7.6 The Frame
Type: Redundantpowersupply
Voltage: 100-240VAC
Frequency: 50/60Hz
Power: 480WMax
Working temperature: 0-40℃
Dimension: 3RUframe（482 mm（W）× 468.5 mm（D）×133 mm（H））
Note ： Specifications are subject to change without notice.