Out of the Box H8CF101 User manual

1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
H8CF101 Assembly manual
V1.20161004

Welcome and thank you for purchasing the H8CF101 conversion kit. I know you are looking forward
to ying an advanced racing drone that can be customized and can deliver e󰀩cient air ow, a strong
frame, and fantastic ying capabilities. In this manual you will nd the instructions that will take you
step by step to comple your drone and to start ying!
As you are working through the instructions it is important that you READ THE DIRECTIONS! There
are ne points covered that you will miss if you only assemble by the pictures. You will enjoy your
journey much more if you follow the instructions provided in this manual.
As always, we are dedicated to your drone ying experience and if you have thoughts, suggestions,
concerns, or want to share a happy ight, please feel free to contact us!
[email protected]
DISCLAIMER:
Out of the Box Innovations RC can not forsee the equipment you will purchase or how you will use
the product when you recieve it. We are not responsible for any injuries or property damage to any-
one or anything as it relates to this product. USE AT YOUR OWN RISK!

Please go over this list below. Verify that all
objects on this list are accounted for before
building your quad-copter.
You will need these items to y your kit.
Eachine H8 or equivalent quad-copter.
8.5mm brushed motors x4
55mm-65mm propellers for the motors x4
(though extras are always recommended)
For FPV ight
Micro Camera with Built in VTX
FX798T Recommended
PICO male connector with small wire attached.
Battery Lipo 500mAh 25C rating or better.
Small philips head screwdriver
Soldering iron
Double Sided Sticky Tape
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN CHECKED
QA MFG APPROVED
Henri 9/27/2016
DWG NO hardware_generic
TITLE
SIZE
D
SCALE
REV
1
14 15
20
25
28
40
5
1.5
.75
8
6
4
3
3
2
M2x20
M2x6
M2x10
M3x6
M3x6
M3x8
M3x10
M3x10
M3x10
M3x12
M3x16
M3x20
34
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 9/27/2016
DWG NO
hardware_generic
TITLE
SIZE
D
SCALE
REV
1
14 15
20
25
28
40
5
1.5
.75
8
6
4
3
3
2
M2x20
M2x6
M2x10
M3x6
M3x6
M3x8
M3x10
M3x10
M3x10
M3x12
M3x16
M3x20
34
M3 x 6 nylon screw
25mm Stando󰀨
Rubber Band
Rubber Caps
x 2
x 1
x 1
x 4
Main Plate
X 1
Side Plate
X 2
Camera Plate
X 1
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm

What you need for this step
What you need for this step What you need for this step
Remove the screws from under the H8 frame. Gently re-
move the top and de-solder the motors from the PCB.
Gently remove the PCB from the quad-copter.
Solder your power tail from the male PICO connector to
your PCB at the point where the battery connects to the
PCB. Be sure to solder positive to positive and negative to
negative. Reversing these may damage your FPV camera.
If you are going to flash your H8 to make it ACRO, then
you’ll also want to attach your flash leads at this time. Use
as small a connector as possible to keep your weight to a
minimum if you’re going to leave it on the board.
Attach the 25mm standoff to the side plate as shown with
1 nylon screw.
Stretch the rubber band between the slots on the side
of the main frame. The battery will be held in place be-
tween it and the frame underneath.
Cut small pieces of double sided tape to hold the PCB
in place on the frame. Make sure the battery connector
fits into the slot as shown. Be sure your PCB is relatively
straight on the frame..
1 2
3 4
PCB Preperation Side Plate Assembly
Battery Strap Assembly PCB Assembly
M3 x 6 nylon
screw
25 MM Standoff
Rubber Band
PCB
Double Sided
Stick Tape
x 1
x 1
x 1
x 1
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
25mm Standoff
Rubber Band
PCB
M3 x 6 Screw
Double Sided Tape

1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
What you need for this step
What you need for this step
What you need for this step
What you need for this step
Assemble your side plates using the attached 25mm
standoff and nylon screw. Be sure to secure the camera
plate between the side plates. Be cautios of the rubber
band and try not to pinch it with the side plates.
Gently pinch the rubber grommet and insert into the
groove at the end of each limb. Release the gromment
and gently adjust any material until it rests in the groove.
A little soapy water can make this part much easier.
Put a tiny bit of soapy water on the bottom of each grom-
met. Gently press the motors until they slide into place
inside the grommet. Adjust the heigh until the top of the
motor is about 5mm from the top of the frame.
Re-connect your motors to the
PCB and verify motor rotation.
Be sure to leave a little slack in the
wires for the protectors.
Mount your FPV camera using a small piece of double
sided sticky tape and secure to the camera plate as
shown. You can adjust from 0 degrees to 20 degrees
angle on your camera by using the correct slots on the
side plates.
5 6
7 8
PCB Preperation Motor Assembly
Pod Assembly FPV Camera Assembly
Side Plates
25mm Standoff
M3 x 6 nylon
screw
Camera Plate
Rubber Grommet
8.5mm Motors
FPV Camera
Double Sided
Stick Tape
x 1
x 1
x 1
x 1
x 4
x 4
x 1
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
FPV Camera Double Sided Tape
25mm Standoff
Rubber Grommet
8.5 Brushed Motor
M3 x 6 nylon screw
Cam Plate

What you need for this step
Gently press on your new 55mm-65mm propellers onto
the motors verifying the direction of the props.
Gently press on the rubber caps to the underside of the
motors which will help protect the motors and
wire connections.
Now you’ve completed your build. Be sure to research
your particular equipment and be sure it is 100% opera-
tional before attempting to fly.
WARNING: NEVER test your motors with the propel-
lers on.
910
PCB Preperation Ready to fly
55mm - 65mm Propellers
Ruber Caps
x 4
x 4
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
Henri 10/4/2016
DWG NO
assy_01
TITLE
SIZE
D
SCALE
REV
1 : 1
5mm
Propeller
Rubber Cap