Outdoor GreatRoom Company Crystal Fire WV-56 User manual

1
The Wave
Installation Instructions for WV-56 Table

2

3
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Contents
Required Tools………………………………….........3
Included with your Fire Pit………………………..4
Assembly Instructions……………………………….5
Gas Connections……………………………………….6
Igniter Installation…………………………………….8
Glass Installation………………………………………9
IMPORTANT
Please consult your Wave Burner instruction manual for detailed
instructions and important information related to hooking up your
burner, including safety information, proper tightening of connections
with two wrenches and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL WV-56-BLK-DIY BURNER WITHOUT
FIRST CONSULTING THE WAVE BURNER OWNER’S MANUAL.
Required Tools
Two people are required for this installation.
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from rough edges found on fire pit table during installation
One AAA Battery (not included)
Required for electric spark igniter installation
Utility Knife
To cut and remove packaging
42450 REV C 8.20.18
,

4
Glass Guard Kit
(Components listed in Glass Guard Manual)
Onyx CFG-O Media
(3 bags)
Included with your Fire Pit
Key for Key
Valve

5
Included with your Fire Pit
A. 4 Fasteners
B. 4 B-Bolts
C. 4 C-Bolts
D. 4 Bolt Caps
E. Touch-Up Paint Bottle
Assembly Instructions
55
Assembly Instructions
Once your fire pit has arrived, begin to unpack the contents.
1. Remove individually the burner from the supercast top and the supercast
top from the base. Set both on a soft, flat surface.
2. Remove access door. Set aside. Then,
place base in desired location. Re-
attach the access door.
3. Next, place the supercast top back
onto the base.

6
1. Reach inside the base and attach gas supply line to the input
shown below, using a 1/2” flare fitting.
TIGHTEN SECURELY WITH A WRENCH
2. Ensure the correct orifices are installed for the fuel type you
are using (see Wave Burner user manual included with burner
for orifice sizing infor the included metal flex hose to the
burner.
TIGHTEN SECURELY WITH TWO WRENCHES
Gas Connections
Read and understand your Wave Burner Owner’s Manual before
beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
2. Ensure the correct orifices are installed for the fuel type you are using (see
Wave Burner user manual included with burner for orifice sizing information).
Propane input
Natural gas input

7
Metal flex
line to
burner
ONLY
TIGHTEN CONNECTION
SECURELY WITH WRENCH
Gas Connections
(continued)
3. Set burner into the fire pit base exactly as shown below and make final
gas connection to the Control Panel.
4. Attach the flex line from the burner
to the gas valve as shown above.
Locate igniter
at this end
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks

8
Sparker will not operate correctly without an ignition and ground wire
attached.
3. Plug both BLACK wires hanging from the burner into the back of the
sparker box.
4. Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Wave Burner Owner’s Manual, if the
spark is weak, intermittent, or not present.
Igniter Installation
1. Make sure the valve is in the
OFF position before beginning.
2. Remove sparker cap by turning
counter-clockwise and insert a
AAA battery (not included).
Reinstall sparker cap.

9
2. Glass guard is required for Wave burner. Install according to instructions
supplied with included glass guard kit.
Glass Installation
1. Scatter glass beads evenly onto burner surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT GLASS BEADS OR
OTHER DECORATIVE MEDIA PRESENT

10
IMPORTANT
Please consult your Wave Burner instruction manual for detailed
instructions and important information related to hooking up your
burner, including safety information, proper tightening of connections
with two wrenches, and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL WV-56-BLK-DIY BURNER WITHOUT
FIRST CONSULTING THE WAVE BURNER OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks

11
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form/
to register your product.
Thank you for purchasing an
Outdoor GreatRoom Company
product! This fire pit was made
with pride in the USA.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]