Outdoor GreatRoom Company DAR-1224-K User manual

Installation Instructions for Darien Fire Pit Table
DAR-1224-K, DAR-1224-EBG-K
Darien Fire Table
outdoorrooms.com

IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER
WITHOUT CONSULTING THE CRYSTAL FIRE®PLUS
OWNER’S MANUAL.
CONTENTS
1. About Your Fire Table 2
a. Required Tools
outdoorrooms.com42523 REV A 10-27-20
!!
1
b. Included With Your Fire Pit
2. Assembly Instructions
a. Unpacking
b. Base Assembly
d. Top Assembly
c. CF-SPARKER Assembly
3. Setting Up Your Burner
a. Gas Connections
b. Thermocouple Installation
c. Electrode Installation
d. Propane Tank Installation
4. Miscellaneous
a. Fire Media Installation
b. Glass Cover Installation
5. Operating Instructions
6. Warnings
3
8
11
12
13

outdoorrooms.com 2
Refer to Crystal Fire®Plus manual for items included with Crystal Fire®Plus burners
• Utility Knife
To cut and remove packaging
• 2 Open Ended Wrenches
To secure gas connections
•Phillips Screw Driver (Do not use a drill to assemble)
For assembly
• One AAA Battery (Not Included)
Required for electric spark igniter installation
A. REQUIRED TOOLS
B. INCLUDED WITH FIRE PIT
1.
CFP1224 Burner and Accessories
(1)
ABOUT YOUR FIRE TABLE
INSTRUCTION MANUAL
5
1
Part
Number
Images
Sizes
Qty.
and
FAA125
XXXX
A
B
C
D
E
F
1
1
1
1
1
1
2 3
4
M6*30
G 8
H 4
M6*20
J 12
M6* 16
H
J
G
J
G
J
G
J
Magnet
Metal
6
POSITION WINGNUT AS SHOWN
A
BD
C
E
F
B
B
C
C
B
D
B
C
D
F
F
F
E
A
F
B
C
D

outdoorrooms.com 3
ASSEMBLY INSTRUCTIONS
A. UNPACKING
Do not discard any packaging until assembly is complete and unit is
tested. Keep all included manuals in a safe place for future reference.
It is recommended to keep top in box on a smooth at surface. This
protects the top from scratches and marks during assembly.
WARNING
Exposed edges may be sharp, use leather gloves
when removing packaging and handling the base.
Do not remove protective cardboard packaging
until you have placed the re pit in
its desired location.
B. BASE ASSEMBLY
2.
1. Using 2X M6*30 Bolts (G) and 2X M6*Ø16 Washers (J), attach tank
Support Base (F) to Side Panel (B) as shown in image below. Loosely
tighten with supplied allen wrench. Take note that wingnut on tank
support ring is aligned according to image below.
!!
INSTRUCTION MANUAL
5
1
Part
Number
Images
Sizes
Qty.
and
FAA125
XXXX
A
B
C
D
E
F
1
1
1
1
1
1
2 3
4
M6*30
G 8
H 4
M6*20
J 12
M6* 16
H
J
G
J
G
J
G
J
Magnet
Metal
6
POSITION WINGNUT AS SHOWN
A
BD
C
E
F
B
B
C
C
B
D
B
C
D
F
F
F
E
A
F
B
C
D
INSTRUCTION MANUAL
5
1
Part
Number
Images
Sizes
Qty.
and
FAA125
XXXX
A
B
C
D
E
F
1
1
1
1
1
1
2 3
4
M6*30
G 8
H 4
M6*20
J 12
M6* 16
H
J
G
J
G
J
G
J
Magnet
Metal
6
POSITION WINGNUT AS SHOWN
A
BD
C
E
F
B
B
C
C
B
D
B
C
D
F
F
F
E
A
F
B
C
D
ALIGN WINGNUT AS SHOWN

outdoorrooms.com 4
2. Using 2X M6*30 Bolts (G) and 2X M6*Ø16 Washers (J), attach Side
Panel (C) to Tank Support Base (F) as shown in image below. Loosely
tighten with supplied allen wrench.
3. Using 4X M6*30 Bolts (G) and 4X M6*Ø16 Washers (J), attach Back
Panel (D) to both Side Panels (B & C) as shown in image below. Loosely
tighten with supplied allen wrench.
INSTRUCTION MANUAL
5
1
Part
Number
Images
Sizes
Qty.
and
FAA125
XXXX
A
B
C
D
E
F
1
1
1
1
1
1
2 3
4
M6*30
G 8
H 4
M6*20
J 12
M6* 16
H
J
G
J
G
J
G
J
Magnet
Metal
6
POSITION WINGNUT AS SHOWN
A
BD
C
E
F
B
B
C
C
B
D
B
C
D
F
F
F
E
A
F
B
C
D
INSTRUCTION MANUAL
5
1
Part
Number
Images
Sizes
Qty.
and
FAA125
XXXX
A
B
C
D
E
F
1
1
1
1
1
1
2 3
4
M6*30
G 8
H 4
M6*20
J 12
M6* 16
H
J
G
J
G
J
G
J
Magnet
Metal
6
POSITION WINGNUT AS SHOWN
A
BD
C
E
F
B
B
C
C
B
D
B
C
D
F
F
F
E
A
F
B
C
D

outdoorrooms.com 5
4. Align Door panel (E) pegs to slotted tab openings. Press Door
Panel (E) back to metal located on Side panels (B & C). See below for
referance.
Fully tighten all screws after completing Step 4.
INSTRUCTION MANUAL
5
1
Part
Number
Images
Sizes
Qty.
and
FAA125
XXXX
A
B
C
D
E
F
1
1
1
1
1
1
2 3
4
M6*30
G 8
H 4
M6*20
J 12
M6* 16
H
J
G
J
G
J
G
J
Magnet
Metal
6
POSITION WINGNUT AS SHOWN
A
BD
C
E
F
B
B
C
C
B
D
B
C
D
F
F
F
E
A
F
B
C
D

outdoorrooms.com 6
C. CF-SPARKER ASSEMBLY
• Locate CF-SPARKER inside of Crystal Fire® Plus burner box.
• Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included)
with + end out.
• Install CF-SPARKER into control panel as shown below. CF-SPARKER must be
installed BEFORE control valve.
• Press in CF-SPARKER button to test your sparker.
CF-SPARKER

outdoorrooms.com 7
Using 4X M6*20 Bolts (H) and 4X M6*Ø16 Washer (J), attach Top (A)
to the assembled base as shown in image below. Tighten with the use
of supplied allen wrench.
* Follow the same process listed above to attach Everblend
(DAR-1224-EBG-K) style top.
D. TOP ASSEMBLY ASSEMBLY
INSTRUCTION MANUAL
5
1
Part
Number
Images
Sizes
Qty.
and
FAA125
XXXX
A
B
C
D
E
F
1
1
1
1
1
1
2 3
4
M6*30
G 8
H 4
M6*20
J 12
M6* 16
H
J
G
J
G
J
G
J
Magnet
Metal
6
POSITION WINGNUT AS SHOWN
A
BD
C
E
F
B
B
C
C
B
D
B
C
D
F
F
F
E
A
F
B
C
D

SETTING UP YOUR BURNER
ATTENTION
Read and understand your Crystal Fire® Plus owner’s manual before
beginning burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.
A. GAS CONNECTIONS
3.
•For hard piped installations. Connect the gas supply line (not included) to
the 3/8” male are tting on the valve.USE TWO WRENCHES TO ENSURE A
GAS TIGHT CONNECTION.
outdoorrooms.com 8
!
!
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner installation
including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE®PLUS OWNER’S MANUAL.
!!
• See Crystal Fire®Plus instructions for burner installation.
• All gas connections were completed at the factory.
• Check all connections for leaks. If needed, tighten connection with 2 wrenches
and re-check for leaks.
• Attach burner valve to control panel with provided screws as shown below.
Ensure CF-SPARKER is installed before this step.

B. THERMOCOUPLE INSTALLATION
outdoorrooms.com 9
C. ELECTRODE INSTALLATION
• Plug both BLACK wires hanging from the burner into the back of the
CF-SPARKER. If an orange wire is present, DO NOT USE IT. The orange wire is
for Direct Spark Ignition system only.
• Test system by pushing the button on the igniter. Consult the troubleshooting
section of the Crystal Fire® Plus owner’s manual if the spark is weak,
intermittent or not present.
SEE DETAIL B
SEE DETAIL A
SCALE 0.800
DETAIL A
SCALE 0.800
DETAIL B
•Refer to Crystal Fire®Plus instruction manual for detailed attachment
of thermocouple.
• Attach thermocouple to burner valve as shown below.

outdoorrooms.com 10
D. PROPANE TANK INSTALLATION ATTENTION
HAND TIGHTEN, DO NOT USE A
WRENCH FOR THIS CONNECTION.
!!
• With the propane tank valve
and re pit valve o, attach the
propane regulator to the propane
tank.
• Place tank in tank tray.
• Ensure no hoses or wires are
contacting the bottom of the
burner.
•Replace the access door.
PROPANE REGULATOR
PROPANE TANK
ACCESS DOOR
TANK TRAY

outdoorrooms.com 11
A. FIRE MEDIA INSTALLATION
B. BURNER COVER INSTALLATION
• Scatter all included glass beads, lava
rock, or other approved re media
evenly across entire burner surface.
WARNING
DO NOT OPERATE CRYSTAL FIRE®
PLUS BURNER WITHOUT INCLUDED
GLASS BEADS OR OTHER APPROVED
FIRE MEDIA.
WARNING
DO NOT OPERATE CRYSTAL FIRE®
PLUS BURNER WITH BURNER COVER
IN PLACE.
4. MISCELLANEOUS
!
!
!
!
• Fully shut o gas supply to table and
turn control valve knob to OFF position.
Wait for burner to become cool before
placing cover.
• Carefully place the cover on top of the
burner.
• Remove burner before attempting
ignition.
(NOT INCLUDED)

outdoorrooms.com 12
OPERATING INSTRUCTIONS
IMPORTANT
Before operating your DAR-1224, DAR-1224-EBG ensure all gas connections are
properly tightened and thoroughly leak checked. Refer to the Crystal Fire®Plus
manual for information on proper leak checking and other critical safety
information.
5.
!
!
!
!
FIRE OR EXPLOSION HAZARD
If you do not follow these instructions exactly, a re or explosion may result causing
property damage, personal injury, or loss of life.
Verify control valve is in OFF position. If operating on a self-contained propane
cylinder, ensure cylinder valve is CLOSED. If operating on a hard-piped system,
ensure main gas supply shut-o valve and all other valves in gas system are
OPEN.
If operating on a self-contained propane cylinder, slowly open cylinder valve.
Press and hold sparker button. Verify an audible and visible spark is present
within the ignition wind guard.
Gently press and turn control knob to LOW/IGNITION position. Fully depress
control knob and hold for 3-5 seconds. Burner should ignite and continue to
operate when control knob is released.
If burner does not light or remain lit after 20 seconds of attempting ignition, turn
control valve to OFF position and wait 5 minutes to allow gas to dissipate before
attempting ignition again. DO NOT ATTEMPT TO LIGHT BURNER IF YOU SMELL
GAS.
With burner lit and operating, the ame height can be adjusted between LOW
and HIGH at any time.
WARNING
OFF
LOW/
IGNITION
HIGH
PUSH AND HOLD
TO IGNITE
DEPRESS SPARKER
BUTTON
SEE DETAIL B
LOOK FOR SPARK
HERE
OFF
LOW/
IGNITION
HIGH
PRESS AND HOLD
SPARKER BUTTON
ROTATE COUNTER-CLOCKWISE
TO LOW AND SLOWLY DEPRESS
HOLD KNOB IN FOR 3-5 SECONDS

outdoorrooms.com 13
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner installation
including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE®PLUS OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember: before
operating, all gas connections must be fully checked for leaks.
6. WARNINGS
!
!
!
!

outdoorrooms.com
Thank you for purchasing an
Outdoor GreatRoom Company
product! This re pit was made
with pride in the USA.
Warranty: Fire pit tables are covered under a 1 year
manufacturer’s warranty.
Please visit http://www.outdoorrooms.com/product-registration
to register your product.
14400 Southcross Drive West • Suite 100 • Burnsville, MN 55306
Toll Free: 1-866-303-4028 • [email protected]