Ovizee WVS1000 User manual
Add-on Camera
WVS1000
User manual
WVS1000
Camera
Power AdapterCamera
Before you install the camera, carefully plan where and how it will be positioned,
and where you will route the cable that connects the camera to the power adaptor.
Avoid installing in a location which requires the wireless signal to pass through
cement, concrete and metal structures. This will reduce the transmission range.
TIP
1. Plug the AC power connector from the power adapter into
the AC adapter port on the camera.
2. Connect the power adapter to a power outlet.
3. The charging LED glows red to indicate the camera is charging.
Charging the Camera
NOTE:
• Only use the included power adapter to charge the camera(s).
• Charge the camera for 8 hours to fully charge.
• USB jack is only for power supply use. No data is transferred.
It is recommended to charge your camera before initial use.
Charging LED
Add-on Camera
WVS1000
Skypegateway
Camera
User manual
Add-on Camera
WVS1000
User manual
WVS1000
Camera
1. Hardware Setup Procedure
1.1 WVS1000
If the device is setup properly, all the LED's in the front panel will light up;
and the two LED's at the RJ45 socket will flash.
WVS1000 will get an IP address from the connected network and
will connect to Skype automatically (if default account is set for the device) .
1.2 Wireless Cameras
Connect the camera with the USB power adapter and switch it on.
Power line Internet line Antenna
Add-on Camera
WVS1000
User manual
2. Software Setup Procedure
2.1 Install the PC application for the WVS1000
(support Windows XP, Vista, 7)
2.1.1 Insert the install disk and double-click the setup.exe.
Follow all the instruction in the installation procedure.
Normally, just press “Next” for default installation.
If Skype application is not installed on computer,
it will download the latest Skype and install it.
Add-on Camera
WVS1000
User manual
2. Software Setup Procedure
The following shows completion of installation.
Add-on Camera
WVS1000
Camera
WVS1000
User manual
2. Software Setup Procedure
2.2 Skype
2.2.1 Create a default skype account for WVS1000
(assume “WVS1000username” as the skype name for this guide)
2.2.2 Login with “WVS1000username”
Run local Skype application, logout any existing account if it is online.
Click to create account
WVS1000username
****************
Add-on Camera
WVS1000
User manual
User manual
2.2.3 Add a contact to the default skype account.
you can add your personal Skype account into the contact list
The added users will be able to connect to the WVS1000 for video stream!
After adding user contact,
sign out default WVS1000 Skype account and signin your
personal Skype account to accept invitation
2. Software Setup Procedure
Add-on Camera
WVS1000
User manual
2. Software Setup Procedure
2.3 OVIZEE WVS1000.
2.3.1 In network connection, find the Upnp device named “Ovizee”.
(if you cannot find the device, that means your Upnp service
is not running on Windows, please go to Appendix A.
Check if Upnp is running before proceeding)
In Windows XP
In Windows 7
In Windows Vista
Double-click the icons to go into configuration website.
Ovizee
Ovizee
Ovizee
Ovizee
Double-click the “WVS1000” icon to pop up an internal webpage.
Add-on Camera
WVS1000
User manual
2. Software Setup Procedure
2.3 OVIZEE WVS1000 (web configuration)
2.3.2 During the initial setup, select an appropriate time zone and click Next.
2.3.3 If you have an existing Skype account for WVS1000,
(following the steps in section 2.2.1),
enter the corresponding information here, then click Next.
If you do not have any existing Skype account,
click on the 'Don't have a Skype Name?'
link to create a new one.
Double-click the icons to go into configuration website.
WV 0
Add-on Camera
WVS1000
User manual
2. Software Setup Procedure
2.3 OVIZEE WVS1000
2.3.5 When a valid Skype account was assigned to WVS1000,
you may now check and adjust its online status.
2.3.4 Fill in all the information to create a new Skype account for WVS1000.
WVS1000
******
******
Camera
Skypegateway
3. General Operations
3.1 Connect to WVS1000
a. Start Skype in your PC/notebook;
b. If your WVS1000 is powered up and connected to the Internet properly,
you should be able to your WVS1000 online with its assigned skype name;
c. As making a normal skype voice/video call, click your WVS1000
on the left to select it and click the Call button or the Video Call button
to make a skype call to WVS1000 as below;
d. Your WVS1000 should automatically answer your skype call and
a life video will then stream to your Skype client from the Camera 1,
which is the default camera to be selected automatically in each skype call-in);
e. You will get a welcome message“Welcome to Ovizee Live!”
from your WVS1000;
f. Also, you will get another message“Cam1 is selected!!!” from your WVS1000
to inform you that the Camera 1 is selected;
Add-on Camera
WVS1000
Quickstart Guide
Add-on Camera
WVS1000
User manual
Add-on Camera
Skypegateway
Camera
Skypegateway
Quickstart Guide
j. Double-click the PandaVideo icon to maximize it as shown below:
Click“Allow access”to grant the access right to PandaVideo and it then minimizes in the system tray as below:
i. Whenever your PC/notebook is powered up, PandaVideo will automatically start;
h. PandaVideo tries to interface to Skype and the following screen will show below:
Right now, you are ready to use WVS1000.
Add-on Camera
WVS1000
User manual
Camera
Skypegateway
3. General Operations
3.1.1 Status of button when a Skype Call is made to WVS1000
Add-on Camera
WVS1000
User manual
Dial out a skype call to
the user’s WVS1000
through Skype App.
Cam 1 is acve (current live
video is streaming from
camera1)
Cams 2, 3, & 4
are inacve
Online status:
GREEN is
online;
otherwise, it is
offline
Camera
WVS1000
Add-on Camera
WVS1000
User manual
3. General Operations
3.2 How to Add/Delete WVS1000 Accounts
Click the buon in
the RED circle.
List out the user’s exisng skype
contacts and their online statues
The checkboxes are for selecng/unselecng the
user’s WVS1000 accounts in his/her contact list.
(It supports at most 4 WVS1000 accounts.).
For those WVS1000 that are not selected in
the list, the buon in the applicaon will be
disabled automacally.
Camera
Skypegateway
Add-on Camera
WVS1000
User manual
3. General Operations
3.3 How to select a camera’s video source
Click the buon in
the RED circle.
Cam1,2,3 are online here.
Cam2 or Cam3 can be
selected to be acve for
receiving its stream live
video. The user’s
WVS1000 will
automacally switch to
stream live video from Cam
2 or Cam3 if its buon is
pressed.
Add-on Camera
Skypegateway
Camera
Skypegateway
User manual
3. General Operations
3.4 How to pair a camera
Click the
buon in
the RED
circle to
enable
Pairing
Mode.
Click the buon
in the RED circle
to select Cam4
for pairing.
Cam4’s green
dot will flashing
during pairing.
Aer
pairing is
done,
Cam4 will
be selected
as acve.
This
indicate
pairing is
successful.
Turn off the camera
and turn on again.
Aer 3 seconds,
Camera
Skypegateway
Add-on Camera
WVS1000
User manual
Click the buon in the RED circle
to toggle the mute state ON/OFF.
3. General Operations
3.5 How to access the mute function
Add-on Camera
WVS1000
User manual
Appendix A.
If Ovizee WVS1000 is connected to the internet, Ovizee device icon will
show up in the My Network Place. If this icon is not existed,
please enable the Upnp service in the following:
Enable UPnP service in windows XP.
• Click Start, click Run, type appwiz.cpl, and then click OK.
• Click Add/Remove Windows Components.
• In the Components window, click Networking Services,
and then click Details.
Make sure Internet Gateway Device and UPnP User Interface are selected
Add-on Camera
WVS1000
User manual
• Follow the instructions that appear on the screen to complete
the installation. Or, if you did not make any changes,
close the Add or Remove Programs windows and Control Panel.
• Start the Services MMC snap-in. To do this, click Start,
click Run, type services.msc, and then click OK.
• Locate SSDP Discovery Service in the list of services.
• If the status is not Started, double-click SSDP Discovery Service
to open the SSDP Discovery Service Properties dialog box.
• In the Startup type box, click Automatic,
and then click Start under Service status.
Then, close the SSDP Discovery Services Properties dialog box.
• Click on Start button, then select Control Panel.
• Click on Network and Internet link, and then click on Network and Sharing Center.
• You will see that network discovery is off.
Click on the corresponding arrow button to expand the section.
• Click “Turn on network discovery”, and then click Apply.
Administrator permission required.
If you are prompted for an administrator password or confirmation,
type the password or provide confirmation.
2. Enable UPnP service in Windows Vista.
Add-on Camera
WVS1000
User manual
I. Hardware Specificaon
This secon provides informaon of the specificaon for the product:
WVS1000
1. RJ45 10/100 Mbps Ethernet port for internet connecon
a) Support DHCP client and stacs IP
2. Power On and Reset buons
3. 6 LED indicator
a) 1 for Skype status
b) 1 for Power status
c) 4 for Camera status
4. Internal 64MB flash memory and 128MB RAM memory
5. Internal ISM band 2.4GHz transceiver
6. SMA connector for changeable external 2.4Ghz antenna
7. Power Adapter: DC5V, 1000mA (Model: Helms-Man, SCB0501000P or
Helms-Man, SHB0501000PE)
SC880
Basic Setup
1. internal ISM band 2.4GHz transceiver
2. internal 2.4Ghz antenna
3. 640 x 480 resolution image up to 15fps
4. Built-in mic
5. 9 x IR LED unit
6. Power Adapter: DC5V, 1000mA
Model: Helms-Man, SCB0501000P or
Helms-Man, SHB0501000P
7. Battery: Li-Polymer rechargeable battery
(Model:TFL703048)
WARNING
Do not use non-rechargeable batteries for the Parent Unit.
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Table of contents
