Owon CB432-DP User manual

Din-Rail Relay
Quick Start Guide

2
WARNING: Failure to follow these safety notices could result in
fire, electric shock, other injuries, or damage to the relay and
other property. Read all the safety notices below before using the
relay.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit yourself.
• Do not expose the unit or its accessories to 󽗊ammable liquids,
gases or other explosives.
Safety Handling

Technical Speci󽗉cations
Wireless Connectivity
ZigBee • 2.4GHz IEEE 802.15.4
ZigBee Pro󽗉le • ZigBee 3.0
RF Characteristics • Operating frequency: 2.4GHz
• Range: 100m (Open area)
Physical Speci󽗉cations
Relay • Single break
Operating Voltage • 100~240 Vac 50/60 Hz
Power consumption • < 1W
Calibrated Metering Accuracy • ≤ 100W ( Within ±2W )
• >100W ( Within ±2% )
Max. Load Current Di󽗈erent models:
• 32 A/63 A
Operating environment
• Temperature: -20℃~ +55℃
• Humidity:
≤ 90% non-condensing
Dimensions • 81 (L) x 36(W) x 66 (H) mm
Weight • 148g

4
Welcome
1
The Din-Rail Relay is a device with wattage (W) and kilowatt hours
(kWh) measurement functions. It allows you to control On/Off
status and to check real-time energy usage via mobile App.
This guide will provide you an overview of the product and help you
to get through the initial setup.
• ZigBee 3.0
• Work with any standard ZigBee Hub
• Control your home device via Mobile APP
• Measure the instantaneous and accumulative energy consumption
of the connected devices
• Schedule the device to automatically power electronics on and o󽗈
• Extend the range and strengthen ZigBee network communication
Features:

5
Installation
2
Important safety information!
• The Din-Rail Relay must be installed and serviced only by
qualified electrical personnel.
• Do not touch the terminals of the device during the testing.
• Turn o󽗈 all power supplying this equipment before installing.
• Make sure that the power supply is off before connecting or
disconnecting it to the auxiliary device.
• Always use a properly rated voltage sensing device to confirm
power is o󽗈.
• Replace all devices, doors and covers before turning on power to
this equipment.
Failure to follow these instructions will result in death or serious
injury.
Wiring Diagram
IN
N
N
L
L
OUT
Please keep the wiring diagram below for future reference.

6
Get to know your device
3
LED indicator
Reset Button & ON/OFF button
IN
N
N
L
L
OUT
LED status What it means
LED keep 󽗊ashing Device has not joined the
network.
LED solid on Device has joined the network.
Flashing three times Identify mode/Return to Factory
Settings.
Green LED Device is ON
Red LED Device is OFF
LED indicator
The LED status gives the following information of the Relay:

7
Reset button
• Pair mode. Press and hold the Reset button for about three
seconds until the LED indicator 󽗊ashes three times. Then you can
bind it with other devices.
• Reset. Press and hold the Reset button for ten seconds.
• (The LED indicator will 󽗊ash three times at third second and 󽗊ash
again at tenth second.) Then the Relay has restore to default factory
settings.
(Note: This step will not clear the energy data.)
• Clear energy data. Restore the device to factory settings twice in
a row, with a period of no more than 10 seconds.

8
4.1 To get started, you will need:
• A Zigbee Gateway.
• A mobile phone with a mobile APP installed.
4.2 Adding to the gateway's network
1. Set your gateway to permit joining(see your gateway's manual).
2. Power on the relay and make sure the LED indicator is 󽗊ashing
(If not, reset it to factory defaults), indicating it is ready to join the
gateway's network.
3. After few seconds the relay will join the gateway automatically
and the LED indicator will become steady when successfully joined.
4. Now you can control on/o󽗈 status as well as measure the power
consumption of the electric circuit.
Note: If the relay fails to join the gateway's network within one
minute, simply reset the relay and retry.
Con󽗉gure Network
4