Owon THS 317-ET User manual

CB432-TY Din-Rail Relay
Quick Start Guide

2
WARNING: Failure to follow these safety notices could result in
fire, electric shock, other injuries, or damage to the relay and
other property. Read all the safety notices below before using the
relay.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit yourself.
• Do not expose the unit or its accessories to 󽗊ammable liquids,
gases or other explosives.
Safety Handling

Technical Speci󽗉cations
Wireless Connectivity
Wi-Fi • 802.11 B/G/N20/N40
RF Characteristics • Operating frequency: 2.4GHz
Physical Speci󽗉cations
Operating Voltage • 100~240 Vac 50/60 Hz
Calibrated Metering Accuracy • ≤ 100W ( Within ±2W )
• >100W ( Within ±2% )
Max. Load Current • 63 A
Operating environment
• Temperature: -20℃ ~ +55℃
• Humidity:
≤ 90% non-condensing
Dimensions • 81 (L) x 36(W) x 66 (H) mm
Weight • 148g

4
Welcome
1
The Din-Rail Relay CB432-TY is a device with electricity functions. It
allows you to control On/O󽗈 status and to check real-time energy
usage via mobile App.
This guide will provide you an overview of the product and help you
to get through the initial setup.

5
• Tuya compliant
• Support Tap-to-Run and automation with other Tuya device
• Control your home device via Mobile APP
• Schedule the device to automatically power electronics on and o󽗈
• Measures Voltage, Current, PowerFactor, ActivePower and total
energy consumption of the connected devices
• Supports custom values for overcurrent protection on the App
• Status can be retained with power failure.
Features:

6
Installation
2
Important safety information!
• The Din-Rail Relay must be installed and serviced only by
qualified electrical personnel.
• Do not touch the terminals of the device during the testing.
• Turn o󽗈 all power supplying this equipment before installing.
• Make sure that the power supply is off before connecting or
disconnecting it to the auxiliary device.
• Always use a properly rated voltage sensing device to confirm
power is o󽗈.
• Replace all devices, doors and covers before turning on power to
this equipment.
Failure to follow these instructions will result in death or serious
injury.
Wiring Diagram
Please keep the wiring diagram below for future reference.
IN
N
N
L
L
OUT

7
Get to know your device
3
LED indicator
Reset Button & ON/OFF button
IN
N
N
L
L
OUT
Reset button
• Reset. Press and hold the Reset button for about 5 seconds until
the LED indicator 󽗊ashes three times (energy data will be cleared).
ON/OFF button
Press once to switch the relay ON/OFF.

8
LED status What it means
Rapidly blink EZ mode
Slowly blink AP mode
Yellow LED solid on Device is ON when connected with
router.
Green LED solid on Device is OFF when connected
with router.
Red LED solid on Device is ON when disconnected.
No light Device is OFF when disconnected.
LED indicator
The LED status gives the following information of the Relay:
• EZ Mode (Default): To pair devices quickly. You can set all devices
to this mode, and then add devices in batches on your phone.
• AP Mode: If there are many devices, while you only want to pair
one device. You can refer to FAQ1 to configure network in this
mode.

9
4.1 To get started, you will need:
• Connect your phone to the 2.4Ghz Wi-Fi network.
• A mobile phone with a 'SmartLife' APP installed.
Then follow the steps below:
• 1. Power on the Din-Rail Relay.
• 2. Make sure the LED indicator is blink rapidly. If not, please reset
it.
Con󽗉gure Network
4
4.2 Add devices
1. Open your App.
2. Login with an existing account. If you are a new user, you need to
create an account at first.
3. Please click the '+' button at the top right corner of the App to
add devices.
4. Select 'Switch Module' to add manually the Din-Rail Relay in
'Energy' list.

10
5. Enter your home Wi-Fi account and password (Only support
2.4Ghz Wi-Fi), then tap 'Next' button.