Oypla GARDEN 4862 User manual

Page 1
Model Code: 4862
Oypla.com LLP / www.oypla.com
User Manual
Model Code: 4862
Contents
1
Front Cover
-
2
Safety
Instructions
-
2
Warnings
-
3
Assembly
Instructions
-
4
Cleaning and
Maintenance
-
4
Trouble
Shooting
-
4Back Cover
Garden Water
Fountain

Page 2
Model Code: 4862
Oypla.com LLP / www.oypla.com
Contents
1
Front Cover
-
2
Safety
Instructions
-
2
Warnings
-
3
Assembly
Instructions
-
4
Cleaning and
Maintenance
-
4
Trouble
Shooting
-
4
Back Cover
End
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
Always unplug the pump from the
electric outlet before cleaning and
handling the fountain.
Use with clean water only. Do not use
other liquids.
Never let the pump run dry, as this can
damage it.
This appliance is earthed.
Do not use the pump with water above
30 degrees Celcius.
Do not lift, carry or pull the pump by the
power cord.
Only use this product on stable, level and
dry ground.
This product is not a toy, and is only to
be used for its designated purpose.
This fountain is the be used outdoors,
but ensure that the plug remains indoors
at all times.
Do not allow children to play with the
product.
Do not replace the power cord. Stop
using the pump if it is damaged.
Plug this fountain into a RCD circuit
breaker before connecting it to the
mains.
This plug is fitted with a 13-amp fuse link,
which is suitable for this type of
appliance and should only be replaced by
a fuse link of the same rating.
This appliance has been fitted with a BS
UK compliant plug which should not be
replaced or removed.
If access to the fuse link is only possible
by removing the plug cover, this must
only be done by a suitably qualified
person.
If the plug or mains cable of this
appliance is damaged, do not use it.
Dispose of the appliance responsibly.
Only use the pump that is supplied with
this appliance.
⚠Never allow water to make contact
with the plug or cable. Doing so can create a
risk of electrical shock.
⚠Children and pets should not play with
or next to this product.
⚠Ensure you have read and
understood the Safety Instructions above
before using this product.
Warnings

Page 3
Model Code: 4862
Oypla.com LLP / www.oypla.com
Parts List:
-If you are missing any of the below parts, please contact
[email protected]
-Please be aware that you will be referring to this parts list throughout the
assembly process.
Contents
1
Front Cover
-
2
Safety
Instructions
-
2
Warnings
-
3
Assembly
Instructions
-
4
Cleaning and
Maintenance
-
4
Trouble
Shooting
-
4
Back Cover
End
Assembly Instructions
1. Invert the small bucket (5) and connect the big
panel (4) with the small bucket (5) by using the
small screws (10).
2. Place the pump (8) into the large bucket (6)
ensuring that the electrical cord is placed in the
hole where the electrical cord fits in the bucket.
Hold the support bar (12) in place on the
underside of the large panel (4) and connect the
small bucket (5) with the large bucket (6) by using
the middle screws (9). Ensure the cable of the
pump goes through the hole of the large panel (4).
3. Connect the handle (1) with the pole (2) using
the large screws (11), and connecting the pole (2)
with the small bucket (5).
4. Connect the pump (8) with the large panel (4)
using the long pipe (7). Connect the large panel
(4) with the small panel (3) using the short pipe
(7).

Page 4
Model Code: 4862
Oypla.com LLP / www.oypla.com
Contents
1
Front Cover
-
2
Safety
Instructions
-
2
Warnings
-
3
Assembly
Instructions
-
4
Cleaning and
Maintenance
-
4 Trouble
Shooting
-
4
Back Cover
End
Cleaning & Maintenance
Unplug the pump from the electrical outlet. Use a small soft brush or rinse it
under running water to clean.
Always unplug the appliance before attempting any cleaning.
Never allow the plug or cord to become wet. Doing so may create a risk of
electrical shock.
To clean the buckets, use only a damp cloth. Do not use any harsh cleaning
substances, as these may damage the product.
Troubleshooting
If the pump fails to run, the following should be checked:
Check the circuit breaker or try a different outlet to make sure that the pump
is getting electric power.
*Note: always disconnect the pump from electrical outlet before checking.
Check the pump discharge and tubing for kinks and obstructions.
Algae buildup can be flushed out with a garden hose.
Remove the pump front cover and plate to access the impeller area. Turn the
rotor to ensure it is not broken or jammed.
With little flow rate, the pump may spew. Check the water level to make sure
the pump is completely submerged.
Imported by Oypla.com LLP, Hangar 1, Upwood Air Park, Ramsey, Cambs, PE26 2RA