OYPLA Home 3866 User manual

Page 1
Manual Version: v1.0
Model Code: 3866
Oypla.com LLP / www.oypla.com
User Manual
Model Code: 3866
Contents
1Front Cover
-
2Safety
Instructions
-
2Warnings
-
3Assembly
Instructions
-
4Installation
Instructions
-
6 Additional
Instructions
-
7Back Cover
End
Stainless Steel Sink

Page 2
Manual Version: v1.0
Model Code: 3866
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
2Warnings
-
3Assembly
Instructions
-
4Installation
Instructions
-
6 Additional
Instructions
-
7Back Cover
End
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
•Never clean the sink using wire wool
and/or abrasive cleaning substances, as
these may damage the product.
•Do not expose the sink ware to bleaches
containing hypochlorite for extended
periods, as this can cause “pitting” in the
surface of the stainless steel. Also, a
reminder that abrasive cleaners,
chemicals used to unblock drains, silver
dip cleaner, salt and vinegar should be
diluted as quickly as possible and flushed
away.
•Do not leave standing water in your sink,
especially when it may contain strong
staining pigments such as coffee or tea.
•Make sure all fastenings are tightly in
place and that everything is in order
before using the product. This should be
checked periodically by an adult.
•Using metal scouring pads on your sink
can not only cause rust and scratches,
but can also lead to discolouring on your
sink’s surface. Do not use metal scouring
pads.
•Avoid placing a rubber mat on your sink
bottom. It provides a perfect
environment for cultivating harmful
bacteria, which can not only cause illness
but can also tarnish your sink’s colour
and finish.
•This product is intended for indoor use
only.
•This product is only to be used for its
intended purpose.
•Do not make modifications or alterations
to this product.
•If your product is damaged or defective,
please contact cserv[email protected]
⚠Be wary of sharp metal edges during
the sink installation process.
⚠Take extra care when using power tools
during the installation process.
Warnings

Page 3
Manual Version: v1.0
Model Code: 3866
Oypla.com LLP / www.oypla.com
Parts List:
-If you are missing any of the below parts, please contact
[email protected]
-Please be aware that you will be referring to this parts list throughout the
assembly process.
Contents
1Front Cover
-
2Safety
Instructions
-
2Warnings
-
3Assembly
Instructions
-
4Installation
Instructions
-
6 Additional
Instructions
-
7Back Cover
End
Assembly Instructions

Page 4
Manual Version: v1.0
Model Code: 3866
Oypla.com LLP / www.oypla.com
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are
available from hardware and plumbing, supply stores. It is essential that the tools
and materials be on hand before work is begun.
Contents
1Front Cover
-
2Safety
Instructions
-
2Warnings
-
3Assembly
Instructions
-
4Installation
Instructions
-
6 Additional
Instructions
-
7Back Cover
End
Installing the Sink

Page 5
Manual Version: v1.0
Model Code: 3866
Oypla.com LLP / www.oypla.com
STEP 1 –CREATING A TEMPLATE
1. Turn the sink upside down on the piece of plywood and draw around it.
2. Cut out the template and place it on the countertop, making sure that the
sink front is parallel to the front of the counter. Be sure the sink is properly centred,
both front to back and side to side.
3. Check for adequate clearance relative to cabinet walls and pull-out or tilt-
down drawers.
4. Tape the template in place and trace the line with a pencil.
5. Accurately mark out a second line 10mm inside the initial bowl outline (to
the appropriate measurement, there are many differences in flange dimensions);
this will be the actual cut-out.
STEP 2 –CREATING SINK CUTOUT
1. Place a brace under the countertop to support the sink cutout area. This
will also make it easier to do the sink cutout.
2. Drill a hole inside every corner of the cutout section outlined by the
template.
3. Place a strip of masking tape along the inside and outside of each cutout
line. The tape protects the countertop surface from scratches while cutting.
4. Insert the saber saw's laminate blade into the pilot hole and cut along the
template lines. When you get to the fourth side of the cutout, support the waste
panel with your hand to keep the edge countertop from splintering as it falls.
Contents
1Front Cover
-
2Safety
Instructions
-
2Warnings
-
3Assembly
Instructions
-
4Installation
Instructions
-
6 Additional
Instructions
-
7Back Cover
End

Page 6
Manual Version: v1.0
Model Code: 3866
Oypla.com LLP / www.oypla.com
STEP 3 –INSERTING & CAULKING
1. Trial fit the sink, by inserting it into the countertop to test whether the cutout
is the correct size.
2. Apply a bead of caulk on the surface of the countertop around the edge
of the cutout. The caulk forms a watertight seal around the edge of the sink and
prevents water damage to the laminate’s substrate.
3. Place the sink in the cutout and press it firmly in place to spread the caulk.
4. Wipe away excess caulk on the countertop around the edge of the sink
with plastic scraper or laminate strip, then wipe clean and smooth with white spirits
and a clean cloth.
Contents
1Front Cover
-
2Safety
Instructions
-
2Warnings
-
3Assembly
Instructions
-
4Installation
Instructions
-
6 Additional
Instructions
-
7Back Cover
End
Additional Guidance
Please refer to the instructions below in regards to cleaning and maintaining your
product.
•After use, the stainless-steel sink ware should be wiped down using: - A soft, damp, soapy
cloth.
- A nontoxic all-purpose cleaner.
- Full-strength distilled white vinegar on a sponge.
•Please take note that hard water can cause a buildup of a grey film on the steel causing a
discoloration.
•For sanitation purposes, we recommend regularly disinfecting your sink with a light bleach
solution, pre-packaged disinfectant wipes, or other mild anti-bacterial solutions. Ensure that
you thoroughly rinse your sink to alleviate any residue or buildup.
•Have your water quality checked. Hard water can cause buildup that can break down the
protective surface of your sink and cause rusting.

Page 7
Manual Version: v1.0
Model Code: 3866
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
2Warnings
-
3Assembly
Instructions
-
4Installation
Instructions
-
6 Additional
Instructions
-
7Back Cover
End