Franke 7612982131844 User manual

18-05.813e-Exp.fm/25.11.11
Installation and operating instructions Montage- en bedrijfsinstructies
Notice de montage et de mise en service Montaż i instrukcja obsługi
Franke Aquarotter GmbH
EA-Nr.: 7612982131844
FAR-Best.-Nr.: 4089 36 24
AQUA612
EA-Nr.: 7612982131998
FAR-Best.-Nr.: 4089 36 29
AQUA616
EA-Nr.: 7612982131950
FAR-Best.-Nr.: 4089 36 24-S
AQUA614
EA-Nr.: 7612982132001
FAR-Best.-Nr.: 4089 36 29-S
AQUA618

2
Inhaltsverzeichnis04.fm
...............................................................3
Please refer to the graphics in the German Instal-
lation and Operating Instructions.
...............................................................16
Les graphiques sont disponibles dans la notice
de montage et de mise en service allemande.
...............................................................30
De tekeningen kunt u in de Duitse montage- en
bedrijfsinstructies vinden.
...............................................................43
Prosimy przyjąć grafikę z niemieckiej instrukcji
montażu i obsługi.

3
18-05.813e-GB.fm
0English
AQUATIMER - A3000 open Shower Panel
made of stainless steel with thermostat, 24 V DC
7612982131844
7612982131998 .......... with InoxPlus® surface finishing
7612982131950 .......... with integrated tray for shower gel
7612982132001 .......... with InoxPlus® surface finishing and integrated tray for
shower gel
Please refer to the graphics in the German Installation and Operating Instructions.
0Table of Contents
1. Abbreviations and Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Description of Product
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7. Scope of Delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
8. Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
9. Installation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
10. Jet dispersion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation, Function and Commissioning
11. Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
12. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
13. Adjusting the Flow Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
14. Setting Hygiene Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
15. Setting the Scald-protector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance
16. Maintenance and Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
17. Cleaning the Jet Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
18. Replacing the Grit Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
19. Replacing the Thermocouple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
20. Replacing the Flow Rate Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
21. Replacing the Non-return Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
22. Changing the Solenoid Valve Cartridge . . . . . . . . . . . . . . . . . . . . . . . 13
23. Fault Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
24. Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4
18-05.813e-GB.fm
1. Abbreviations and Units
2. Key
Warning!
Failure to observe can result in injury or even death.
Caution!
Failure to observe can result in material damage.
☞Important!
Failure to observe can cause the product to malfunction.
☞Useful information for optimally handling the product.
3. Warranty
Liability is accepted according to the General Terms and Conditions of Business and
Supply.
Use original replacement parts only!
DN Nominal diameter in mm
RCD Residual Current Protective Device,
Earth leakage circuit breaker
SELV Safety Extra Low Voltage
SW Width A/F
TW Drinking water
TWW Hot drinking-water
EA-Nr. European Article Number
FAR-Best.-Nr. Franke Aquarotter Order Number
Conversion 1 mm = 0.03937 inches
1 inch = 25.4 mm
All length specifications in the graphics are in mm.

5
18-05.813e-GB.fm
4. Important Notes
• Installation, commissioning and maintenance are to be performed only by a
qualified technician according to the instructions provided and in accordance with
legal requirements and acknowledged rules of technology.
• All technical connection regulations specified by the local water and electricity
supply utility companies must be complied with.
• When using the device for paid water distribution with AQUAPAY coin-activated
switches, carefully observe the connection guide provided in the instructions for the
AQUAPAY coin-operated switch.
• All rights reserved to make technical alterations.
5. Application
AQUATIMER - A3000 open shower panel made of stainless steel, for on-wall
installation, with electronic time-control, thermostatic mixer and a facility for paid
water distribution via AQUAPAY coin-activated switches, and a feature for externally
controlling options such as fitting settings and communication via ECC function
controller. For connection to the hot and cold water supply. Split-second adjustment of
flow duration.
Individual control unit in compact design.
Control functions:
– Optional temperature sensor on the hot water side; the temperature is measured
and a protocol is saved every 60 seconds, during thermal disinfection every 10
seconds
– Temperature-controlled hygiene flushing in conjunction with optional
temperature sensor on the cold water side
– Time-controlled hygiene flushing, optionally with fixed interval or after a certain
defined time after last usage
– Peak load program for demand-oriented fitting functions
Additional functions with ECC function controller (Ethernet):
– Automatic thermal disinfection according to DVGW work sheet W 551 as well as
safety switch-off
–Cleaningswitch-off

6
18-05.813e-GB.fm
6. Technical Specifications
7. Scope of Delivery
8. Dimensions
9. Installation Example
10. Jet dispersion
Minimum flow pressure: 1.0 bar
Recommended flow pressure: 1-5 bar
Maximum operating pressure: 10 bar
Calculation flow rate: Drinking-water 0.15 l/s
Hot drinking water 0.15 l/s
Volumetric flow:
Fitting: 0.20 l/s at a flow pressure of 3 bar
Bypass: 0.06 l/s at a flow pressure of 3 bar
Operating voltage: 24 V DC
Power consumption: 2.5 W
Communication: Ethernet via ECC function controller
Type of protection: IP 68
Quantity Description
1 Stainless-steel casing with: Thermostat, electronic
module M1, Piezo-button, solenoid-valve cartridge,
blockable water flow regulators, connecting hoses and
AQUAJET Slimline shower head
1ElectricT-junction
4 Wood screw, dowel
1 Hook-in strip
2Connectionbracket
1 Flow rate regulator 0.15 l /s
1 Installation and Operating Instructions
Connections can be selected
from
top A = 50
rear A = max. 200

7
18-05.813e-GB.fm
11. Assembly Instructions
Warning!
Use the fitting only with non-return valves and the grit filters specified.
Failure to observe can result in an increased bacterial load in drinking water and cause
a health risk or even risk of death.
Warning!
• Operate the product only with safety extra low voltage (SELV). Do not earth the
components.
• The power supply (not included in the scope of delivery, see accessories,
Chapter 24) must be set up outside of the wet area, in a separate room.
• Secure the electric connection with an earth leakage circuit breaker (RCD).
Failure to observe can mean risk of death or material damage, e. g. from electric shock
or fire.
☞Important!
Before installing, flush the pipes in compliance with DIN 1988.
☞To protect the tiles, use masking tape when marking and drilling. Drill at low speed.
☞Depending on the composition of the wall, special wall dowels may have to be used (to
be provided by the customer).
☞The system line (not included in scope of delivery) for connecting the power supply to
the fittings must be installed in a conduit (to be supplied by customer) and looped
through.
Installing the Electric T-junction
☞Important!
The components of the electronic T-junction must be installed only when they are in a
dead condition.
☞Recommended system lines see Chapter 24., Accessories.
When using other cables for the system line, note the different colour coding. The outer
diameter must not exceed 7.5 mm.
Fig. A: Water connection from above
Fig. B: Water connection from rear
11.1 Only when the water connection is from the rear: Install the connection bracket (a)
leaktight.
11.2 Screw in the water volume regulators (b) leak-tight.
11.3 Align the water volume regulator in such a way that the screw plug and the operating
element are freely accessible.
11.4 For a shower head height of 2.10 m to 2.30 m, mark drill holes for installation at a
height (c) of 2.14 m to 2.34 m from the upper edge of the prefabricated foot base.
11.5 Drill according to the markings.
11.6 Insert the dowels.
11.7 Screw on the hook-in strip.
11.8 Hook-in the stainless steel housing.

8
18-05.813e-GB.fm
11.9 Mark the other drill holes.
11.10 Remove the stainless steel housing.
11.11 Drill according to the markings.
Insert the dowels.
11.12 Strip the shielding (a) off from the system lines (approx. 40 mm).
11.13 Fit the union nut (c) on to the system line (b) up to the stop.
☞The cable cores are marked with numbers 1 through 4.
A: Union nut
B: FAR Order No. 84-032-12.468
FAR Order No. 84-032-12.534
FAR Order No. 84-032-12.563
FAR Order No. 84-032-12.720
11.14 Latch the cable cores (d) into the cable core guides (e) according to their colours.
11.15 Cut off the protruding ends of the cable core so that they are flush, i. e. so that they do
not protrude.
11.16 Place the union nut (c) on the electronic T-junction (f) and tighten with the required
torque (1.2 Nm).
Caution!
Ensure correct polarity.
Each core cable colour must be in the same cable core guide on both union nuts.
☞When the union nut is being tightened, an electric contact and the pull-relief are
automatically established.
Special seals provide protection against dust and water.
11.17 Install the line connections between the electronic module, the solenoid-valve
cartridges and the Piezo-button.
A: Solenoid valve cartridge, mixed water (Actuator 1)
B: Solenoid valve cartridge bypass, thermal disinfection (Actuator 2, optional)
C: Analogue output 0-10 V
D: Temperature sensor, cold water (optional)
E: Temperature sensor, hot water (optional)
F: AQUAPAY coin-operated switch (optional)
G: Piezo-button
H: Electric T-junction system lines (Power)
K: Electronic module
11.18 Only when the water connection is from the rear: Bring forward work steps 11.20 to
11.22.
11.19 Hook the stainless steel housing into the hook-in strip and fasten with screws.
AB
1 brown red
2white white
3 blue blue
4black black

9
18-05.813e-GB.fm
11.20 Take the hoses together with the water volume regulators and connect them to the hot
and cold water lines.
11.21 Use a hollow hexagon wrench to open the water volume regulators.
d: closed
e: open
11.22 Check the water connections for leaks.
12. Function
Triggering water flow
12.1 Press the Piezo-button.
•Waterflows.
• Water flow stops automatically after the set flow duration time has passed or when
the Piezo-button is pushed again.
Flow duration
The flow duration has been factory-set to 30 s. The flow duration can be altered in
increments of 0.1 seconds, from 1 – 6500 s.
Selecting the temperature
13. Adjusting the Flow Duration
Flow duration can be adjusted with a free program available from Franke (FAR Order
No. 4897 00 00).
14. Setting Hygiene Flushing
Hygiene flushing can be adjusted with a free program available from Franke (FAR Order
No. 4897 00 00).
15. Setting the Scald-protector
Warning!
If the hot-water supply temperature is more than 45 °C, set the scald-protector.
Failure to observe can cause bodily harm due to scalding.
☞The scald-protector (hot water limit) is factory set to 40 °C (in compliance with
DIN 1988) . Before using, set the plant-specific parameters.
15.1 Remove the cover platelet (a).
15.2 Loosen the screw (b).
15.3 Remove the temperature selection knob (c) and the stop ring (d).
15.4 Trigger the valve.
15.5 The temperature can be made freely selectable or it can be set to a permanent value.
➀To set the temperature to be freely selectable:
Use the regulating nut (e) to set the maximum water temperature, e. g. to 40 C.

10
18-05.813e-GB.fm
➁To set a permanent temperature:
Use the regulating nut (e) to set the required water temperature, e. g. to 40 C.
15.6 Slide the stop ring (d) on to the regulating nut (e).
➀Temperatur frei wählbar einstellen:
Den Anschlag (f) des Anschlagringes an die hintere Kante (g) des Steges (i) stellen.
➁Temperatur dauerhaft voreinstellen:
Die Aussparung (h) des Anschlagringes genau auf den Steg (i) schieben.
15.7 Den Temperaturwahlgriff (c) auf den Anschlagring (d) schieben.
r: rot
☞Push the temperature selector knob on to the limit ring so that both red dots point
upwards (12-o’clock-position).
15.8 Use the screw (c) to secure the temperature selection knob (b) on the fitting.
15.9 Press the cover platelet (a) on to the temperature selector lever.
16. Maintenance and Servicing
Depending on the quality of the water, the local conditions and the rules and
regulations applicable on site, the fitting must be maintained and serviced at regular
intervals.
Perform maintenance on the following components:
• Shower head (see Chapter 17.)
•Filters(seeChapter 18.)
• Non-return valves (see Chapter 21.)
Use suitable cleaning agents that are not harmful to the fittings in a proper manner and
rinse with water after use. High-pressure cleaners must not be used for cleaning.
Remove the stainless steel housing
Some maintenance work requires that the stainless steel housing be removed.
16.1 Only when the water connection is from the top:
Close the flow volume regulator.
a: closed
b: open
16.2 Only when the water connection is from the top:
Trigger the valve.
Release the connecting hoses for hot and cold water from the water volume regulators.
16.3 Loosen the screws on the stainless steel housing.
☞Never let the stainless steel housing hang by the connecting hoses.
16.4 Unhinge the stainless steel housing.
16.5 Only when the water connection is from the rear:
Close the flow volume regulators (see Instruction Step 16.1).
16.6 Only when the water connection is from the rear:
Trigger the valve.
Release the connecting hoses for hot and cold water from the water volume regulators.