Padom SH-02 User manual

Padom Sunrise Alarm
Clock User Manual (EN)
01

To reduce the risk of Fire, Electric Shock, or Injury to
Persons:
1.This appliance is only intended for household use, including
similar use in hotels.
2.Place this appliance on a stable, level and non-slippery
surface.
3.Do not use this appliance in wet surroundings (e.g. in the
bathroom or near a shower or swimming pool).
4.Make sure the adapter does not get wet.
5.Do not let water run into the appliance or spill water onto the
appliance.
6.Only use the original adapter. Do not use the other adapter if
they are damaged.
7.This appliance has no on/off switch to disconnect the
appliance from the power source, remove the plug from the
wall outlet.
8.Do not use this appliance as a means to reduce your hours
of sleep. The purpose of this appliance is to help you wake up
more easily. It does not diminish your need for sleep.
9.This appliance has a built-in back up battery in the base to
remember your settings of clock and alarm when the power
goes off. AC power must be required for the clock and all
functions to work. It supports AC 100-240V input.
02

1.Clean the appliance with a soft cloth.
2.Do not use abrasive cleaning agents, pads or cleaning
solvents like alcohol, acetone, etc., as this might damage the
surface of the appliance.
3.lf the appliance will not be used for an extended period of
time, remove the power cord from the wall outlet and store the
appliance in a safe, dry surroundings where it will not be
crushed, banged, or subject to damage.
03

You have to set the clock time when you plug in the appliance
for the first time.
1. Hold the setting button (in the lower right corner) for 2
seconds to enter the time setting mode.
2. Click+/- button (in the upper left corner) to select "Hour".
For example, "6". Click the setting button to confirm it.
3. Click+/- button (in the upper left corner) to select "Minute".
For example, "15". Click the setting button to confirm it.
4. Click+/- button (in the upper left corner) to select "12H or
24H". For example, "24H". Click the setting button to confirm
it.
04
Please note: When the 12-H time format is selected, AM or PM
icon will be displayed.

1. Press the alarm 1 button to turn the alarm 1 on. Hope the
alarm 1 button for 2 seconds to enter the alarm 1 setting
mode.
2. Press+/- button to adjust "Hour". For example, "6". Press
the alarm 1 button to confirm it.
3. Press+/- button to adjust "Minute". For example, "30".
Press the alarm 1 button to confirm it.
4. Press+/- button to adjust "Ringtone". You can choose
between 7 pre-set sounds or FM radio as a wake-up sound.
Press the alarm 1 button to confirm it.
5. Press+/- button to adjust "Volume". Press the alarm 1
button to confirm it.
6. Press+/- button to adjust "Brightness". Press the alarm 1
button to confirm it.
7. Press+/- button to adjust "Sunrise Simulation Time". You
can set it to 10 minutes. Press the alarm 1 button to confirm it.
05

Please note: When alarm clock goes off, if there aren't any
operations within 15 minutes, it will turn off the light and sound
automatically.
1. Press the LED light button (in the upper left corner when you
face the clock) to enter the manual color light mode.
2. Press the +/- button to adjust brightness of the light.
3. Double click the LED light button to enter the auto color light
mode, which means it will change the light color automatically.
Please know that when the clock is in this mode, the light will
maintain maximum brightness and you can't adjust the
brightness of the light.
4. Press the +/- button to adjust different colors of lights
manually, which means it will keep the color of the light until you
press the +/- button again. There are 7 colors for you to choose.
06
You have set up the alarm 1. The sunrise light will be on gradually from 10%
brightness to 100% by 10 minutes from 6:20 AM. 10 minutes later, the alarm
will go off at 6:30 AM. You can get an extra 9 minutes of sleep time after
pressing the snooze button (snooze up to 5 times). You can turn the alarm
off by pressing the alarm 1 button. {Take alarm 1 as an example, alarm 2 is
the same.)

5. Press the LED light button again to quit the colorful light mode.
07

1. Hold the radio button down for 2 seconds, the clock will
scan all the available stations automatically and save them as
P-01/P-02/P-03 and so on (up to 10 channels). You don't need
to do anything until it finishes the process.
2. After finishing, the clock radio will select P-01 channel by
default.
3. Press the volume"+"/"-" button (near the radio button) to
adjust the radio volume.
4. Hold the volume "+"/"-" button for 2 seconds to select
P-02/P-03 or another channel.
5. Press the FM radio button again to quit the FM radio mode.
08

1.Press ode.
2.Hold the fall-asleep button for 2 seconds to set the
fall-asleep mode.
3.Press the + / - button to adjust the Timer (up to 120
minutes). And then press the fall-asleep button to confirm it.
4.Press the + / - button to adjust the Brightness. And then
press the fall-asleep button to confirm it.
5.Press the + / - button to adjust the sound. You can choose
between 3 pre-set sounds or FM radio as a fall-asleep sound.
And then press the fall-asleep button to confirm it.
6.Press the + / - button to adjust the volume. And then press
the fall-asleep button to confirm it.
7.Now you are in the fall-asleep mode. You can still press the
+ I - to adjust brightness and press the volume + / - button to
adjust the volume at this point.
8.Press the fall-asleep button again to quit the fall-asleep
mode.
09

Specifications
Material: PC, ABS, Electronics
Size: 170×170×55 mm
Weight: 350g
Battery: Built-in 210mAh Battery
FM Frequency: 78–108 MHz
Light Brightness function: 20 levels light brightness
Alarm volume: 15 level volume setting
Charging mode: Adapter
Power: 10 W
Input Voltage(V): DC 5V
Working Time (hours): 30000
Light Source: LED
10
Please Note: After finish
setting, the light will slowly
turn on from the pre-set
brightness level to dark, and
the light will turn off at the
end of the preset time.

Q 1: This appliance doesn't work at all.
1. Perhaps the adapter is not inserted properly in the
walloutlet. Plug the adapter properly in the wall outlet.
2. Perhaps there is a power failure. Check if the power supply
works by connecting another appliance.
Q 2: The radio products a cracking sound.
1. Perhaps the broadcast signal is weak, please fully unwind
antenna and move it around until you receive the best recep-
tion.
Q 3: Could I completely turn off the time display?
1. Yes, you can adjust the brightness of the time display, or
turn it off by clicking the setting button several times.
Q 4: Does this clock have a back-up battery option in the
event of a power outage?
1. This clock has a built-in back up battery in the base to
remember your settings of clock and alarm when the power
goes off, but it does NOT support battery operated. AC power
must be required for the clock and all functions to work. It
supports AC 100-240V input.
11

Q 5: How can I turn the alarm sound off once it has gone
off?
1. You just need to press the corresponding alarm button. So
if you set "Alarm 1" press the "Alarm 1" button on the side and
it should shut off.
Q 6: Can I make it so that only the light comes on, not the
alarm? ( Or can I set the alarm so there is only sound, no
light?)
1. You can set the volume to the lowest level when you setup
an alarm. That means when the alarm goes off, the sound is
almost invisible, and only the light is on.
2. When setting an alarm, you can select the lowest light
intensity, which means when the alarm clock goes off, there is
almost no light.
12