Palermo Smart Camera User manual

Smart Camera Guide
Read and understand this safety awareness and
instruction manual thoroughly before using your
camera, and keep it for future reference.
If you would like to watch video setup:
YYP2P: https://youtu.be/7DMNWkU1KfY
YOOSEE: https://youtu.be/4puRoH34UG8

24/7 PHONE SUPPORT 252-316-0108
- 1 -
Please note: Camera works best on normal 2.4
GHz WIFI and does not support 5GHz WIFI. Most
routers broadcast both 2.4GHz and 5GHz networks
simultaneously. No need to disable your 5GHz
network to use the camera.
TO RESET THE CAMERA for any reason during setup:
Use included pin to place into RESET hole (see photo
below).
Be sure to hold the reset button for at least 10
seconds until you hear reset sound “CHICHING”.
(Please note: if after 1 minute you do not hear the
camera beeping repeat the above instructions by
holding the reset pin for another 10 seconds until you
hear the reset sound,“CHICHING”. The camera is not
reset unless you hear the reset sound,”CHICHING”.

24/7 PHONE SUPPORT 252-316-0108
- 2 -
IOS Phone Users: Go to the App Store, search for YYP2P
or YOOSEE and download the App.
Android Phone Users: Go to the Play Store, search for
YYP2P or YOOSEE and download the App.
It does not matter which app you use on your mobile device.
You cannot use both apps for the same account. The app
you use on the initial setup device (mobile phone) you will
need to use the same app for all additional devices. Do not
mix the apps.
Step 1:
Open YYP2P / YOOSEE App on your mobile device.
Tap on the Register button to get to the next screen.

24/7 PHONE SUPPORT 252-316-0108
- 3 -
Do not use a phone number to register, only email
addresses are used in the United States.
Once you have successfully registered, you will be
redirected to Account login to enter your password.

24/7 PHONE SUPPORT 252-316-0108
- 4 -

****Click on (CHINA) at the top of the screen and a
dropdown menu will open. Select America. The United
States is not an option then Click Login****
Step 2:
Add Device by tapping “+” in top right-hand corner of your
screen.

24/7 PHONE SUPPORT 252-316-0108
- 5 -
Click Add New Device, to add device to your WIFI.

24/7 PHONE SUPPORT 252-316-0108
- 6 -
FYI:
Add Online Device Option for YYP2P Only. Cannot
use with YOOSEE app due to the New Sharing
Feature.
Note: You will need to have your camera plugged in
at this point. (If you had already plugged in your
camera from the start and it stopped beeping,
unplug the camera from the electrical outlet and
plug it back in.
The camera goes through a bootup process once it is
plugged into the electrical outlet. That process takes about
30-50 seconds before it starts beeping.

24/7 PHONE SUPPORT 252-316-0108
- 7 -
Step 3: Smartlink
Step:4
Enter your WIFI password, and tap next step.
While camera is beeping, tap Hear the beeping. Keep
phone and camera at a 30cm distance and tap next step.

24/7 PHONE SUPPORT 252-316-0108
- 8 -
Connection usually takes no more than 20–30 seconds.
Once connected you will automatically be taken to the
Connection Succeeded, screen. Enter the default codes
(name the camera “example: Camera 1” & password:123),
then tap save in the top right corner of your screen.

24/7 PHONE SUPPORT 252-316-0108
- 9 -
Tap on the Chinese writing in the grey box on the left side
of your screen, you will see, “On-line”. Tap; online to see
live video. Click OK to access the microphone and enjoy
your camera.
You should be all set and enjoying your camera. If you
were setting this camera up the Ethernet cable, please
continue with instructions below.

24/7 PHONE SUPPORT 252-316-0108
- 10 -
Ethernet Connection:
Step:1
Unplug and re-plug your camera from the electrical outlet
so it can reload. When the camera starts beeping, connect
your Ethernet cable to your router and the back of your
camera. Once the Ethernet cable is plugged in, the
beeping will stop and there will be a green and yellow light
coming out of the back of the camera from the Ethernet
cable and a dim yellow light in the front of the camera
(Network Indicator light).
Step:2
Login to your app, on the device list screen you will see
highlighted in blue (discover new device). Tap on it.

24/7 PHONE SUPPORT 252-316-0108
- 11 -
Once you tap Discover New Device you will see the
device ID number and a blue (+) sign on the right. Tap on
the blue (+) sign. Name the camera and enter passcode
(use default name & passcode during initial setup).
Tap on the Chinese writing in the grey box on the left side
of your screen, wait for it to say “online”, and tap. Click OK
to access the microphone.

24/7 PHONE SUPPORT 252-316-0108
- 12 -
Transfer from Ethernet to WIFI
Step:1
Tap the gear icon(settings) at top right corner of screen.
Tap network settings.
On the next screen, Do Not Click On WIFI.
Find your network in the list of networks.
Tap on your network and Confirm the change.
Put in your WIFI password and confirm.
Wait for the blue checkmark to appear on your
network.
Step:2
Tap the arrow at the top left of screen to go back (2x).
You want to be back on the picture screen.
Make sure you still have live video, if not tap the screen.
Disconnect Ethernet cable and enjoy your camera.

24/7 PHONE SUPPORT 252-316-0108
- 13 -
YOOSEE DEVICE SHARING INSTRUCTIONS
If you are using the YOOSEE app, click on the sharing icon on the all devices screen. The icon is 3
little circles clumped as a triangle located at the upper right of the play button. It gives you the
option to share your camera to 10 devices by sending a link to the person you wish to share too.
The person will have to register their app with their own email address and password then scan
the link that you sent them. Your camera information will show on their app.
Sharing management.
Click the share button,
The "Share Administration" interface appears and you can delete
shared friends or share them with other friends.
PS：
In the "Security Settings" section, add the RTSP password setting.
Share the model to add the device, do not display the admin password and
the guest password.

24/7 PHONE SUPPORT 252-316-0108
- 14 -
YYP2P MANUALLY ADDING MULTIPLE DEVICES.
Manually Adding Devices
The camera can only be smart linked once. The first mobile device is
considered the initial device. Every device after that must be added
manually. FYI. there can only be (1) one account per app. Meaning, all
added devices must use the same account information exactly. Below
are the instructions for adding multiple devices.
Manually Adding Devices
The camera can only be smart linked once. The first mobile device is
considered the initial device. Every device after that must be added
manually. FYI. there can only be (1) one account per app. Meaning,
all added devices must use the same account information exactly.
Below are the instructions for adding multiple devices.
Manually Adding Devices Method 1 (With Mobile Data)
For devices connecting away from camera location
1) Install the app on the mobile device.
2) Log into the app using the same login information you created
for the initial setup device.
3) No need for the mobile device to be connected to the WIFI.
4) On the All devices/devices list screen tap the (+) sign in the top
right corner.
5) Add online Device
6) Input the same Name as the initial device.
7) Input the device id /(3CID) which is the 7 digits at the bottom of
the camera under the barcode.
8) Input the same passcode as the initial device and tap (Save) in
the top right of the screen.

24/7 PHONE SUPPORT 252-316-0108
- 15 -
9) Tap on the word (Online) on the left side of the picture for live
view.
Manually Add Devices Method 2 (Connected to same WIFI as the
camera)
1) Install the app on the mobile device.
2) Log into the app using the same login information you created
for the initial setup device.
3) Make sure the mobile device is connected to your home WIFI
2.4 GHz.
4) On the All devices/devices list screen, the camera will
automatically pop up on the screen highlighted in blue as (Discover
New Device), tap on it. Tap on the blue (+) sign.
5) Input the same Name & Password as the initial setup device
then tap (Save) in the top right of the screen.
6) Tap on the word (Online) on the left side of the picture for live
view.

24/7 PHONE SUPPORT 252-316-0108
- 16 -
Usage Tips when using with a smart phone:
Tap the camera image to connect. If it times out, wait one
second and tap again. This may happen several times
depending on your internet speed.
Double tap the camera image to use full screen.
To move the camera position, slide your finger either left
to right or up to down and vice versa.
To zoom, slide two fingers moving out in opposite
directions.
Muting: Tap the sound button and there will be an “X”
when muted and “))))” when not muted.
To speak, hold the microphone button then speak into the
smart phone. When finished speaking, release the button.
To take a photo, tap the camera button.
Activate Motion Detection Sensor Alarm: Go to the
settings icon located between the camera and information
icons. Click the settings icon then tap Alarm settings and
set. On this same screen you can also set the camera to
take photos.

24/7 PHONE SUPPORT 252-316-0108
- 17 -
Computer Setup:
Note: You must first set up your camera on your smart
phone since the camera needs to be connected to your
WIFI for this.
1. Turn on your computer.
2. Enter "www.yoosee.co" in the browser.
Yoosee web page:
Click on CMS for PC, and the Apple Icon for Mac.

24/7 PHONE SUPPORT 252-316-0108
- 18 -
Once you select your choice, the download will begin.
Click on file: cmssetup.exe and click Next.
Click Next again.

24/7 PHONE SUPPORT 252-316-0108
- 19 -
Click Install.