PALI Crib User manual

PALI spa
via Palmarina 115
33048 San Giovanni al Natisone
Udine Italy
tel. [phone]
fax [phone]
e-mail [e-mail]
www.paliitaly.com
Assembly
instructions
ref: stationary side
Version 2004
A B D E F G
H
4x 4x
I
4x
J
4x
4x 4x
Z
2x (left + right)
4x 4x
1x
C
4x
1 mattress base (K)
1 dropside (L)
1 stationary side (M)
2 ends (N)
2 rails (P)
1 drawer front (R)
1 drawer center partition (S)
2 drawer ends (T)
2 drawer bottoms (U)
1 drawer back (V)
Crib and drawer parts list
Tools needed
for assembly
INSTRUCTION
LEAFLET
Important, keep
for future reference.
Read carefully
IMPORTANT: In order to properly assemble the cot, carry out the operations in
the order specified. Failure to assemble the crib in the manner recommended
could make the crib hazardous.
Carefully remove and lay out all parts. Familiarize yourself with all diagrams to
facilitate the assembly of your crib. Check parts enclosed in hardware bag with
the HARDWARE PARTS LIST to be sure all are included and quantities are correct.
This crib has been designed for your child's
comfort and your convenience. Quality
material and workmanship have gone into
this crib which will provide a sound and
comfortable bed for your baby if properly
assembled and maintained. For the security of
your child and your own peace of mind be
sure to follow the assembly instructions
exactly. A periodic check should be made of
all bolts and screws, which should be
tightened if needed. Moisture and heat are
harmful to the finish; for this reason use
extreme caution when a vaporizer is in use.
The vapor steam should always be aimed
away from the crib as well as away from any
other wood furniture. Some types of soft
plastic toys could damage the finish when
placed against it.
(not available
on Renee crib)

R
When installing tracks to head & foot boards track
stamped "R" must be placed on right side, track
stamped "L" must be placed on left side. Make sure
the small wheel located on the track is closest to
the front of the crib. Be very careful to the correct
positioning: the track must ALWAYS be positioned
with the small wheel towards the drawer front and
downwards. Fix the tracks using the 4 screws C.
1Applying the metal tracks (Z) to the ends (N)
Footboard (right)Headboard (left)
Headboard
2Casters
Place casters and inserts (G) in bottom of
each leg as shown in Diagram 2, then very
carefully place crib upright.
IMPORTANT: Don't strike the wheels! Place a
piece of wood or something similar that will
fit between the wheels, and gently tap with a
hammer.
N
G
G
insert
caster
hammer
piece of wood
Diagram 2
Diagram 1
C
C
C
Z Z
Red
ring
Edge
L
C
Z Z
Red
ring
Edge

3a
HEADBOARD/FOOTBOARD (ENDS) ATTACHMENT TO RAILS. You will now attach headboard/footboard (ends) (N) to the rails.
Place a curved fastener plate (F) into the large holes on inside of the rails (P) (refer to Diagrams 3 and 4 for placement).
Insert each allenhead bolt (long) (B) into holes located in both ends (N), and into hole in end of rails (P) until seated in
threads of holes in curved fastener plates (F).
Assembling crib and positioning of mattress base
Diagram 3
Diagram 4
F
P
K
N
N
P
P
H
N
D
BE
P
receiving
hole
F
E
B
D
H
N
K
N
AH
Mattress base
lower position
K
I
IMPORTANT: follow carefully the illustrations below.
Correct positioning of the plastic
caps to the mattress support frame
in cribs with headboard/footboard
with rectangular posts
IMPORTANT!
Make sure grooves
are toward
the outer side
of mattress
support frame
Correct positioning of the plastic
caps to the mattress support frame
in cribs with headboard/footboard
with rounded posts
IMPORTANT!
Make sure grooves
are toward
the inner side
of mattress
support frame
INN
I
K K

3b Mattress base higher position
K
M
AH
4Applying the stationary side
J
N L
R
T
U
U
T
When assembling drawers with roller glides, assemble the sides of the drawer so the small wheels are toward the back of the
drawer. The wheels drop into the openings in the rail mounted at the inside of the headboard and footboard. Attach the
drawer ends and the center partition to the drawer back as shown on Diagram 5; slide the bottom panels, making them run
in the grooves, and when the insertion is complete, attach the front panel and tighten the fastenings.
5Drawer assembly
insert the pins
into the relative
holes and turn the key
unlocked position locked position
Diagram 5
key
grooves for
drawer bottom
S
V

N
L
K
6 d
20-30 cm
20-30 cm
L
N
K
N
L
6 c
1
3
3
4
2
6 b
L
N
K
NL
6 a Applying the
dropside
7Inserting the drawer
Stationary side M
Dropside L
Assembled drawer

!WARNING!
FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
KEEP THESE INSTRUCTIONS FOR FUTURE USE.
BEFORE each assembly inspect crib for damaged hardware, loose joints, missing parts
or sharp edges. Upon completion of assembly be sure all screws, bolts and fastening
devices have been tightened securely. A frequent check should be made during the use
of the crib to make sure all parts remain tight and secure.
DO NOT use any crib if any parts are missing or broken.
DO NOT substitute parts!
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
DO NOT use a waterbed mattress.
DO NOT leave child in crib with the side lowered. Be sure side is in raised and locked
position whenever child is in crib.
DO NOT tie pacifiers, necklaces or any other items around a child's neck or on crib
parts. THIS COULD CAUSE STRANGULATION!
WHEN CHILD IS ABLE TO PULL INTO A STANDING POSITION lower the mattress to the
lowest position. Remove all bumper pads, large toys and other objects that could serve
as steps for climbing out. When child is able to climb out or reaches the height of 35
inches, the crib must no longer be used. The child should then be transferred to a youth
or regular bed.
If refinishing the crib, use only a non-toxic finish specified for children's products.
Never use plastic shopping bags or other plastic film as a mattress protector because
they can cause suffocation.
ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27 1/4", BY 51 5/8"
WITH A THICKNESS NOT EXCEEDING 6".
(The dimensions shall be taken seam-to-seam or edge-to-edge where
appropriate.)
This crib conforms to the applicable regulations of the Consumer Product Safety Commission.