Panasonic DMP-BD45GA User manual

©Panasonic Corporation 2010.
Unauthorized copying and distribution is a violation
of law.
ORDER NO.CHM1003008CE
Blu-ray Disc Player
Model No. DMP-BD45GA
DMP-BD45GC
DMP-BD45GN
DMP-BD45GW
DMP-BD45GT
DMP-BD45PU
DMP-BD65GN
DMP-BD65PU
DMP-BD65PX
Vol. 2
Colour
(K).......................Black Type

2

3
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions----------------------------------------------- 4
1.1. General guidelines ---------------------------------------- 4
1.2. Caution for fuse replacement--------------------------- 4
2 Warning -------------------------------------------------------------- 5
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatic Sensitive (ES) Devices -------------- 5
2.2. Service caution based on legal restrictions --------- 6
3 Service Navigation ----------------------------------------------- 7
3.1. Combination of Multiple Pressing on the
Remote Control -------------------------------------------- 7
3.2. Entering Special Modes with Combination of
Multiple Pressing on the Remote Control ----------- 7
4 Service Mode ------------------------------------------------------ 9
4.1. Self-Diagnosis and Special Mode Setting ----------- 9
5 Service Fixture & Tools----------------------------------------19
6 Block Diagram----------------------------------------------------20
6.1. Digital P.C.B. Regulator Block Diagram-------------20
6.2. Analog Video/Audio Block Diagram------------------21
6.3. Timer Block Diagram ------------------------------------22
6.4. Digital (Back End Section) Block Diagram ---------23
6.5. IC Pin Terminal Chart------------------------------------24
6.6. Digital (Front End Section) Block Diagram---------25
7 Schematic Diagram -------------------------------------------- 26
7.1. Interconnection Schematic Diagram ---------------- 26
7.2. BP1 (BP) Schematic Diagram ------------------------ 27
7.3. EX-BUS Section Schematic Diagram--------------- 28
7.4. BP1_PERI Section Schematic Diagram------------ 29
7.5. BP1_CH0 Section Schematic Diagram------------- 30
7.6. BP1_CH1 Section Schematic Diagram------------- 31
7.7. ETHER Section Schematic Diagram---------------- 32
7.8. FE Section Schematic Diagram (1/2) -------------- 33
7.9. FE Section Schematic Diagram (2/2) -------------- 34
7.10. AUDIO_IO Section Schematic Diagram ----------- 35
7.11. DAC_HDMI Section Schematic Diagram --------- 36
7.12. DIGITAL_NET Section Schematic Diagram ------ 37
7.13. TIMER Section Schematic Diagram ---------------- 38
7.14. VIDEO_OUT Section Schematic Diagram -------- 39
8 Printed Circuit Board ------------------------------------------ 40
8.1. Digital P.C.B. ---------------------------------------------- 40
9 Exploded View and Replacement Parts List ----------- 49
9.1. Exploded Views ------------------------------------------ 49
9.2. Electrical Replacement Parts List-------------------- 51
10 Schematic Diagram for printing with A4 size---------- 59

4
1 Safety Precautions
1.1. General guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1. Leakage current cold check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1MΩand 5.2MΩ.
When the exposed metal does not have a return path to
the chassis, the reading must be .
1.1.2. Leakage current hot check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a
0.15μF capacitors, between each exposed metallic part
on the set and a good earth ground such as a water pipe,
as shown in Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more sensi-
tivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 volts
RMS. A leakage current tester (Simpson Model 229 or
equivalent) may be used to make the hot checks, leakage
current must not exceed 1/2 milliampere. In case a mea-
surement is outside of the limits specified, there is a pos-
sibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the cus-
tomer.
1.2. Caution for fuse replacement

5
2 Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive
(ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semi-
conductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient
to damage an ES device).

6
2.2. Service caution based on legal restrictions
2.2.1. General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees
C (662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)

7
3 Service Navigation
3.1. Combination of Multiple Pressing on the Remote Control
Press multi-buttons (in combination) on the remote control simultaneously for operations, such as initialization or service mode, etc.
There are no multiple pressing functions on the previous remote controls, thus, please be sure to use the supplied remote control.
3.2. Entering Special Modes with Combination of Multiple Pressing on the
Remote Control
Enter the following special modes by multiple pressing functions on the supplied remote control.
After entering each mode, switch to the desired menus for operation.
3.2.1. Disclosure mode (Combination of multiple pressing: [OK] [Blue] [Yellow])
Press and hold [OK] [Blue] [Yellow] on the remote control simultaneously for 5 sec., then "00 RET" is displayed on FL display
window.

8
3.2.2. Nondisclosure mode 1 (Combination of multiple pressing: [6] [7] [Yellow])
Press and hold [6] [7] [Yellow] on the remote control simultaneously for 5 sec., then [50 RET] is displayed on FL display window.
3.2.3. Nondisclosure mode 2 (Combination of multiple pressing: [5] [9] [Red])
Press and hold [5] [9] [Red] on the remote control simultaneously for about 5 sec., then "70 RET" is displayed on FL display
window.

9
4 Service Mode
4.1. Self-Diagnosis and Special Mode Setting
4.1.1. Self-Diagnosis Functions
Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has
occurred.
U** and F** are stored in memory and held.
You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode.
Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is ON.
Error Code Diagnosis contents Description Monitor Display Automatic FL display
U30 Remote control code error Display appears when main unit and remote
controller codes are not matched.
No display
* is remote controller code of the
main unit.
Display for 5 seconds.
U59 Abnormal inner temperature
detected
Display appears when the drive temperature
exceeds 70°C.
The power is turned off forcibly.
For 30 minutes after this, all key entries are
disabled.
The event is saved in memory as well.
No display
U59 is displayed for 30 minutes.
U71 HDMI incompatible error
(HDMI incompatible)
Display this error when the equipment (com-
patible with DVI such as TV, amplifier etc.)
connected to the unit by HDMI is incompatible
with HDCP (High-bandwidth Digital Content
Protection).
No display
U72 HDMI connection error
(communication error)
This error is displayed when there are any
communication problems with the unit and the
equipments (TV, amplifier etc.) connected to
the unit by HDMI. (or when there is a problem
with the HDMI cable)
The display disappears only when the con-
nection is released. Neither the button opera-
tion nor the passage of the fixed time
disappear the display.
No display
U72 display disappears when
error has been solved by Power
OFF/ON of connecting equipment
or by inserting/removing of HDMI
cable.
U73 HDMI connection error
(authentication error)
When authentication error occurs while the
equipments (TV, amplifier etc.) are connected
by HDMI. (or when there is a problem with the
HDMI cable)
The display disappears only when the con-
nection is released. Neither the button opera-
tion nor the passage of the fixed time
disappear the display.
No display
U73 display disappears when
error has been solved by Power
OFF/ON of connecting equipment
or by inserting/removing of HDMI
cable.
U76 Connection error Display this error when the equipment (com-
patible with DVI such as TV, amplifier etc.)
connected to the unit by HDMI is incompatible
with HDCP (High-bandwidth Digital Content
Protection).
No display
U77 Illegal disc error This error is displayed when it becomes
impossible to reproduce because of copyright
illegal information.
No display
U88 Restoration is operation.
(When the disc is in the disc
tray)
This error is displayed when there is a disc in
the disc tray or abnormality is confirmed dur-
ing playback. It is shown that the restoration
to return the main unit operation normally is
operating. It becomes possible to use as soon
as not the breakdown but the U88 display dis-
appears.
No display
Display for 30 seconds.
F00 No error information Initial setting for error code in memory
(Error code Initialization is possible with error
code initialization and main unit initialization.)
No display No display
F34 Initialization error When initialization error is detected after start-
ing up main microprocessor, the power is
turned off automatically.
The event is saved in memory.
No display No display

10
4.1.2. Special Modes Setting
F58 Drive hardware error When drive unit error is detected, the event is
saved in memory.
No display No display
F74 HDMI Device Key Communica-
tion error.
This error is displayed when the information
error is occurred at HDMI device key loading.
No display
F75 HDMI incompatible error
(HDMI incompatible)
Display this error when the equipment (com-
patible with DVI such as TV, amplifier etc.)
connected to the unit by HDMI is incompatible
with HDCP (High-bandwidth Digital Content
Protection).
No display
F99 Hang-up Displayed when communication error has
occurred between Main microprocessor and
Timer microprocessor.
No display
Displayed is left until the [POWER]
key is pressed.
UNSUP-
PORT
Unsupported disc error *An unsupported format disc was played,
although the drive starts normally.
*The data format is not supported, although
the media type is supported.
*Exceptionally in case of the disc is dirty.
“This disc is
incompatible.”
It is displayed for 5 seconds.
The character indication flows
sideways.
NO READ Disc read error *A disc is flawed or dirty.
*A poor quality failed to start.
*The track information could not be read.
“Cannot read.
Please check the
disc.”
HARD
ERR
Drive error The drive detected a hard error. “DVD drive error.”
It is display for 5 seconds.
The character indication flows
sideways.
SELF
CHECK
Restoration operation Since the power cord fell out during a power
failure or operation, it is under restoration
operation.
*It will OK, if a display disappears automati-
cally. If a display does not disappear, there is
the possibility that defective Digital P.C.B. /
BDP drive.
No display
The character indication flows
sideways.
UNFOR-
MAT
Unformatted disc error This error is displayed when the unformatted
DVD-RAM/DVD-RW or the DVD-RW
recorded by another make of recorder is
inserted.
No display UNFORMAT
This disc is not formatted properly.
Format the disc in DISC MAN-
AGEMENT?
PLEASE
WAIT
Unit is in termination process Unit is in termination process now.
“BYE” is displayed and power will be turned
off.
No display
The character indication flows
sideways.
No PLAY When there is a viewing restric-
tion on a BD-Video or
DVD-Video.
Rating password is set. No display
Item FL display Key operation
Mode name Description Front Key
Rating password The audiovisual level setting password is
initialized to Level 8. While the unit is on, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds.
- "00 RET" is displayed on the unit's
display.
Repeatedly press [ ] on the
remote control or [POWER] on the
unit until "03 VL" is displayed on the
unit's display.
Press [OK] on the remote control
or [OPEN/CLOSE] on the unit.
Error Code Diagnosis contents Description Monitor Display Automatic FL display

11
Service Mode Setting every kind of modes for servicing.
*Details are described in 7.1.3. (BD) Service
Mode at a glance.
Turn the power off.
Press the [5] [9] and [R] button
simultaneously for five seconds,
then [70 RET] is displayed on FL.
Press the [ ] or [ ] button to
select until [80 SRV] is displayed on
FL.
Press the [OK] button .
*The command is transmitted by
attached remote control.
BD-ROM history cleaning < Persistent Storage> of BD-ROM standard is
cleaned.
Screen display: [The history has been
cleared] is displayed for five seconds. Same display as before execution.
When the power is on, disc is not in
tray, press [STOP] and [POWER
(Remote Controller)] keys simulta-
neously for 5 seconds.
Forced disc eject Removing a disc that cannot be ejected.
The tray will open and unit will shift to P-off
mode.
While Demonstration Lock is being set, this
Forced disc eject function is not accepted.
While the unit is off, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds.
- "00 RET" is displayed on the unit's
display.
Repeatedly press [ ] on the
remote control or [POWER] on the
unit until "06 FTO" is displayed on
the unit's display.
Press [OK] on the remote control
or [OPEN/CLOSE] on the unit.
Forced power-off When the power button is not effective while
power is ON, turn off the power forcibly.
Display in P-off mode. Press [POWER] key over than 4
seconds.
Aging Perform sequence of modes as * Aging
Description shown below continually.
Display following the then mode. Turn the power on.
Press the [5] [9] and [R] button
simultaneously for five seconds,
then [70 RET] is displayed on FL.
Press the [ ] or [ ] button to
select until [81 AIG] is displayed on
FL.
Press the [OK] button .
*The command is transmitted by
attached remote control.
NOTE1:
If the unit has hung-up because of
pressing keys for over 10 seconds,
once turn off the power, and re-exe-
cute this command.
*When releasing Aging mode, press
[POWER] key over 4 seconds.
Item FL display Key operation
Mode name Description Front Key

12
Demonstration
lock/unlock
Ejection of the disc is prohibited.
The lock setting is effective until unlocking the
tray and not released by Main unit
initialization of service mode.
*When lock the tray.
“LOCK” is displayed for 3 seconds.
When the power is on (SS mode),
press [PLAY] and [OPEN/CLOSE]
keys simultaneously for 5 seconds.
Note:
When a disc is not in tray, this
setting is not effective.
*When unlock the tray.
UNLOCK is displayed for 3 sec-
onds.
When the power is on (SS mode),
press [PLAY] and [OPEN/CLOSE]
keys simultaneously for 5 seconds.
*When press [OPEN/CLOSE] key
while the tray being locked.
Display LOCK for 3 seconds.
Press [OPEN/CLOSE] key while the
tray is being locked.
Progressive initialization The progressive setting is initialized to Inter-
lace.
The display before execution
leaves.
When the power is on (SS mode),
press [STOP] and [PLAY] simulta-
neously for 5 seconds.
Default setting The date of Menu, Mode and EEPROM
setting, etc. is set to the default condition in
factory.
“HELLO” is displayed 10 seconds.
While the unit is off, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds.
- "00 RET" is displayed on the unit's
display.
Repeatedly press [ ] on the
remote control or [POWER] on the
unit until "08 FIN" is displayed on
the unit's display.
Press and hold [OK] on the
remote control or [OPEN/CLOSE]
on the unit for at least 3 seconds.
Item FL display Key operation
Mode name Description Front Key

13
4.1.3. Service Modes at a glance
Information necessary for service can be displayed.
Service mode setting:
1. Turn the power off.
2. Press the [5] [9] and [R] button simultaneously for five seconds, then [70 RET] is displayed on FL.
3. Press the [ ] or [ ] button to select until [80 SRV] is displayed on FL.
4. Press the [OK] button.
5. It is displayed on FL as [HELLO-->SERV].: It is shown to have entered the service mode.
6. The command is transmitted by attached remote control.
Method of making clear service mode: Press the power button (power off).
The display of information to each command is as follows.
NOTE:
Do not use it excluding the designated command.
Item FL display Key operation
Mode name Description (Remote controller key)
Release Items Item of Service Mode executing is cancelled. Press[0][0] or [Return] in service
mode.
Error Code Display Last Error Code of U/H/F held by Timer is dis-
played on FL.
*Details are described in
7.1.1. Self-Diagnosis Functions.
If any error history dose not exist,
[F00] is displayed.
Press [0] [1] in service mode
ROM Version Display The display contents are switched over every
5 seconds.
1. Region code
2. Main firm version
3. Timer firm version
4. Drive firm version
5. ROM correction version
6. BOO2 version
7. BOO3 version
Press [0] [2] in service mode

14
Drive application check Checking whether the drive is applicable drive
or not.
Press [0] [3] in service mode.
Drive Check Simple quality of BD drive
*If the date of the present or the
trouble occurred time is incorrect, it
may be not able to judge correctly.
Press [3][8] in service mode.
Laser Used Time
Indication
Check laser used time (hours) of drive.
(****) is the used time display in
hour.
Laser used time of BD/ DVD/ CD
in Playback/Recording mode is
counted.
Press [4] [1] in service mode.
Item FL display Key operation
Mode name Description (Remote controller key)

15
BD drive last error BD drive error code display. 1. Error Number is displayed for 5
seconds.
2. Time when the error has occurred
is display for 5 seconds.
YY: Year
MM: Month
DD: Day
3. Last drive error (1/2) is displayed
for 5 seconds.
00 : Bad disc
03 : Bad disc
04 : Bad disc or drive malfunction
4. Last drive error (2/2) is displayed
for five seconds.
5. Error occurring disc type is dis-
played for 5 seconds.
Press [4] [2] in service mode.
Item FL display Key operation
Mode name Description (Remote controller key)

16
6. Disc maker ID is displayed for 5
seconds.
7. Factor of drive error (hexadeci-
mal) occurring is left displayed.
In case that the maker cannot be
identified, display is blackout.
Item FL display Key operation
Mode name Description (Remote controller key)

17
8. When the last error doesn't exist .
CEC (H) output check Check of the CEC terminal high output of
HDMI.
Press [5] [5] in service mode.
CEC (L) output check Check of the CEC terminal low output of
HDMI.
Press [5] [6] in service mode.
Manufacturing Date Read out the manufacturing date of the unit.
YY: Year
MM: Month
DD: Day
Press[6][1]in service mode.
Tray OPEN/CLOSE Test The BD drive tray is opened and closed
repeatedly.
*is number of open/close cycle
times.
Press [9] [1] in service mode
*When releasing this mode, press
the [POWER] button of Remote
Controller more than 4 seconds.
Delete the Laser Used
Time
Laser used time information stored in the
memory of the unit is deleted.
Press [9] [5] in service mode.
Delete the Last Drive
Error
Laser Drive Error information stored on the
BD Drive is deleted.
Press [9] [6] in service mode.
Delete the Error History Error History information stored on the unit is
deleted.
Press [9] [7] in service mode.
Item FL display Key operation
Mode name Description (Remote controller key)

18
Initialization of Error code Last Error Code information stored by timer is
deleted. (Write in F00)
Press [9] [8] in service mode.
Initialization of the
Service Mode
Last Drive Error, Error History and Error code
information stored on the unit are initialized to
factory setting.
Press [9] [9] in service mode.
Release Service Mode Release Service Mode and turns the Power
Off.
Display in STOP (SS) mode. Press [POWER] button on the front
panel or Remote controller in ser-
vice mode.
Item FL display Key operation
Mode name Description (Remote controller key)

19
5 Service Fixture & Tools
Part Number Description Compatibility
RFKZ0215 Extension Cable (Power P.C.B. - FL P.C.B. / 12 Pin) Same as BR570 Series
RFKZ0216 Extension Cable (Power P.C.B. - Digital P.C.B. / 23 Pin) Same as BR570 Series
RFKZ03D01KS Lead Free Solder (0.3mm/100g Reel) Same as BD60 Series
RFKZ06D01KS Lead Free Solder (0.6mm/100g Reel) Same as BD60 Series
RFKZ10D01KS Lead Free Solder (1.0mm/100g Reel)) Same as BD60 Series
RFKZ0316 Solder Remover (Lead free low temperature Solder/50g) Same as BD60 Series
RFKZ0328 Flux Same as BD60 Series

20
6 Block Diagram
6.1. Digital P.C.B. Regulator Block Diagram
DIGITAL P.C.B. REGULATOR
BLOCK DIAGRAM
19,20,21,22
P58001P1102
(REG.PW_D3.3V)
IC58003
SW
VCC
3
FB 5
7
2
EN PW_D3.3V
PW_1.8V
PW_D1.2V_A
PW_D1.2V_C
+5V
PW_3.3V
PW_3.3V
IC51001-VDDR,VDDA
IC51001-VDDIO,VDDIOCK
IC51001-VDD,VDDUSB, IC56036-VDD12
(DC-DC CONVERTER)
IC58004
VCC OUT2 H
OUT2 L
LX2
OUT1 H
OUT1 L
VO1
20
EN2
EN1
8
1
15
17
16
23
21
4
Q58003
D1
7
D1 D2
D2
D2
D2
G1
G2
8
2
4
5
S1 1
6
(REG.PW_1.8V)
Q58004
D1
7
D1
G1
G2
8
2
4
5
S1 1
6
(REG.PW_1.2VC)
12,13,14
P58001P1102
(REG.+5V)
IC56001
VIN
VOUT 4
1
5
ON
(REG.PW_3.3V)
IC57006
VIN
VOUT 4
1
5
ON
(REG.PW_SUB5V)
PW_DR12V
IC51701
Vin
Vout 3
1
2ON[H]
(REG.DR12V)
Q58006
4
3
(REG.PW_DR5V)
IC58302
VIN
VOUT 3
2
1
ON[H]
PW_X_SW5.9V
PW_X_SW12.2V
PW_HSW5V
1 2
(REG.PW_AD5V)
IC54001
VIN VOUT 3
2
1
ON[H]
FROM
POWER P.C.B.
FROM
POWER P.C.B.
2
P58001 P1102 TO POWER P.C.B.
1
P51701-
IC57001-
14 35
IC55006-
/
28 39
P55001-
/
3 12
IC55005-
/
41
/54 /55 /
16
IC55005-
67
/31 59 //
JK56001-
18
4
P51602-
12 37
IC51301-
/
2
,IC53003-
2
IC53002-
7 8
IC59001-
/25
/26 /
10 14
IC56036-
18
63 65
//
22
/26 /37 /43 /
66 82
/95 /100 /110 /111 /127 /
52
/
/
/ /
72
73
/
74
/75 /76 /77 /78 /82 83
// 84 /
79
/80
/81
/
IC51001-VDD33,AVDD_APLL1,AVDD_MPLL2,
AVDD_MPLL1,AVDD_DPLL,VDDAUSB,VDDPUSB
,JK59001-
69 70
IC52001,IC52002,IC52201,IC52202-
/71
/
HDMI_P_ON[H]
IC57001-
55
FROM TIMER
SECTION
P_STANBY_H
IC57001-
42
FROM TIMER
SECTION
JC_P_ON[H]
IC57001-
49
FROM TIMER
SECTION
DR_P_ON_H
IC57001-
43
FROM TIMER
SECTION
(REG.PW_HSW5V)
IC51702
/OC
Vout 5
1
4
EN3
Vin
FROM BP1_PERI
SECTION
FROM BP1_PERI
SECTION
SBI1
IC51001-
P31
IC51001-
FROM FE
SECTION
IP55005
D5V
DR5V
A5V
2
1
5
6
1 2
IP55004 (REG.BLD8V)
IC55002
VIN
VO 3
2
1
VC
(REG.DR5V)
IC55007
1
8
5
BLD8V BLD8V
23
IC55006-
12V
C25
3 6
QR58001
(SWITCHING)
21
IC57005
(RESET)
VDD OUT IC57001-
14
FB1 3
LX1
22
VO2
10
FB2
11
PW_AD5V
D58001
SBO1
IC51001-
2 16
IC53001-
/
1 10
IC54002-
/
PW_DR5V
only for BD65GN/PU/PX
only for BD45GA/GC/
GN/GW/PU
only for BD45PU/65GN/65PU/65PX
only for BD65GN/PU/PX
W32
V34
DMP-BD65GN/PU/PX
DMP-BD45GA/GC/GN/GT/GW/PU