Panasonic DMP-BD75GA User manual

©Panasonic Corporation 2011.
Unauthorized copying and distribution is a violation
of law.
ORDER NO.CHM1104018CE
Blu-ray Disc Player
Model No. DMP-BD75GA
DMP-BD75GC
DMP-BD75GN
DMP-BD75GT
DMP-BD75GW
DMP-BD75PU
Vol. 2
Colour
(K).......................Black Type

2

3
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions----------------------------------------------- 4
1.1. General guidelines ---------------------------------------- 4
1.2. Caution for fuse replacement--------------------------- 4
2 Warning -------------------------------------------------------------- 6
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatic Sensitive (ES) Devices -------------- 6
2.2. Service caution based on legal restrictions --------- 7
3 Service Navigation ----------------------------------------------- 8
3.1. Combination of Multiple Pressing on the
Remote Control -------------------------------------------- 8
3.2. Entering Special Modes with Combination of
Multiple Pressing on the Remote Control ----------- 8
4 Specifications ----------------------------------------------------10
5 Service Mode -----------------------------------------------------12
5.1. Self-Diagnosis and Special Mode Setting ----------12
6 Service Fixture & Tools----------------------------------------21
7 Measurements and Adjustments---------------------------22
7.1. Service Positions -----------------------------------------22
8 Block Diagram----------------------------------------------------23
8.1. Digital P.C.B. Regulator Block Diagram-------------23
8.2. Digital (Back End Section) Block Diagram--------- 24
8.3. IC Pin Terminal Chart ----------------------------------- 25
8.4. Digital (Front End Section) Block Diagram -------- 26
9 Schematic Diagram -------------------------------------------- 27
9.1. Interconnection Schematic Diagram ---------------- 27
9.2. AUDIO_DAC Section Schematic Diagram -------- 28
9.3. AV Section Schematic Diagram ---------------------- 29
9.4. MTK Section Schematic Diagram (1/2)------------- 30
9.5. MTK Section Schematic Diagram (2/2)------------- 31
9.6. DIGITAL_NET Section Schematic Diagram------- 32
9.7. DDR Section Schematic Diagram ------------------- 33
9.8. FE Section Schematic Diagram (1/2) -------------- 34
9.9. FE Section Schematic Diagram (2/2) -------------- 35
10 Printed Circuit Board ------------------------------------------ 36
10.1. Digital P.C.B. ---------------------------------------------- 36
11 Appendix for Schematic Diagram ------------------------- 45
11.1. Voltage and Waveform Chart ------------------------- 45
11.2. Electrical Replacement Parts List-------------------- 48

4
1 Safety Precautions
1.1. General guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1. Leakage current cold check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1MΩand 5.2MΩ.
When the exposed metal does not have a return path to
the chassis, the reading must be .
1.1.2. Leakage current hot check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a
0.15μF capacitors, between each exposed metallic part
on the set and a good earth ground such as a water pipe,
as shown in Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more
sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 volts
RMS. A leakage current tester (Simpson Model 229 or
equivalent) may be used to make the hot checks, leakage
current must not exceed 1/2 milliampere. In case a mea-
surement is outside of the limits specified, there is a pos-
sibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the cus-
tomer.
1.2. Caution for fuse replacement

5
1.2.1. Micro Fuse conducting check
This unit uses the Micro Fuse.
Check the Micro Fuse conducting using the Tester at the check points below.

6
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive
(ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semi-
conductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient
to damage an ES device).

7
2.2. Service caution based on legal restrictions
2.2.1. General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees
C (662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)

8
3 Service Navigation
3.1. Combination of Multiple Pressing on the Remote Control
Press multi-buttons (in combination) on the remote control simultaneously for operations, such as initialization or service mode, etc.
There are no multiple pressing functions on the previous remote controls, thus, please be sure to use the supplied remote control.
3.2. Entering Special Modes with Combination of Multiple Pressing on the
Remote Control
Enter the following special modes by multiple pressing functions on the supplied remote control.
After entering each mode, switch to the desired menus for operation.
3.2.1. Disclosure mode (Combination of multiple pressing: [OK] [Blue] [Yellow])
Press and hold [OK] [Blue] [Yellow] on the remote control simultaneously for 5 sec., then "00 RET" is displayed on FL display
window.

9
3.2.2. Nondisclosure mode 1 (Combination of multiple pressing: [6] [7] [Yellow])
Press and hold [6] [7] [Yellow] on the remote control simultaneously for 5 sec., then [50 RET] is displayed on FL display window.
3.2.3. Nondisclosure mode 2 (Combination of multiple pressing: [5] [9] [Red])
Press and hold [5] [9] [Red] on the remote control simultaneously for about 5 sec., then "70 RET" is displayed on FL display
window.

10
4 Specifications
Power supply: AC220V-240V, 50/60Hz
(BD75GA/GC/GW)
AC110V, 60Hz
(BD75GT)
AC220V-240V, 50Hz
(BD75GN)
AC110V-240V, 50/60Hz
(BD75PU)
Power consumption: Approx. 12W
(BD75GA/GC/GN/GT/GW)
Approx. 14W(BD75PU)
in standby mode: Approx. 0.2W
(BD75GA/GC/GN/GW/PU)
Approx. 0.1W(BD75GT)
in quick start standby mode: Approx. 3.6W
(BD75GA/GC/GN/GW)
Approx. 3.3W
(BD75GT)
Approx. 3.8W
(BD75PU)
Operating temperature range: +5C to +35°C(+41 to +95°F)
Operating humidity range: 10% - 80%RH (no condensation)
Signal system: PAL/NTSC
(BD75GA/GC/GN/GT/GW)
NTSC
(BD75PU)
Video output:
output level: 1.0Vp-p (75Ω)
output connector: Pin jack (1 System)
Video performance:
Horizontal resolution: More than 500 lines
Video S/N ratio: More than 65dB
Audio output:
output level: 2 Vrms (1kHz, 0dB)
output connector: Pin jack
number of connector: 2 channel
1 system
Audio performance:
Frequency response:
DVD(linear audio): 4Hz-22kHz (48kHz sampling)
4Hz-44kHz (96kHz sampling)
CD-Audio: 4Hz-20kHz
S/N ratio: 100dB
Dynamic range: 100dB
Total harmonic distortion: 0.004%
HDMI AV output:
Output connector: TypeA (19pin),
1 system
USB slot:
USB 2.0: 1 system
Ethernet:
10BASE-T/100BASE-TX: 1 system
Regional Code: DVD: #3(BD75GA/GT)
BD: Region A
DVD: #2(BD75GC)
BD: Region B
DVD: #5(BD75GW)
BD: Region C
DVD: #4(BD75GN)
BD: Region B
DVD: #4(BD75PU)
BD: Region A
Media:
Playable discs:
BD-Video(BD-LIVE,
BONUSVIEW):
BD-ROM Version2.3
BD-RE: Version3 (Single Layer/Dual
Layer), JPEG
BD-R: Version2 (Single Layer/Dual
Layer), MKV(*4, *5, *6), DivX(*4,
*5, *7 )
DVD-R: DVD-Video format (*1), DVD
Video Recording format(*1),
AVCHD format(*1), JPEG(*2),
MP3(*2), MKV(*2, *3, *5, *6),
DivX(*2, *3, *5, *7)
DVD-R DL: DVD-Video format (*1), DVD
Video Recording format(*1),
AVCHD format(*1), JPEG(*2),
MP3(*2), MKV(*2, *3, *5, *6),
DivX(*2, *3, *5,*7)
DVD-RW: DVD-Video format (*1), DVD
Video Recording format(*1),
AVCHD format(*1)
+R: Video(*1), AVCHD format(*1)
+R DL: Video(*1), AVCHD format(*1)
+RW: Video(*1), AVCHD format(*1)
DVD-Video: DVD-Video format
CD-Audio: CD-DA
CD-R/CD-RW: CD-DA, JPEG(*2), MP3(*2),
MKV(*2, *5, *6), DivX(*2, *5, *7)
*1: Finalizing is necessary.
*2: ISO9660 level1 or 2(except for extended formats), Joliet.
This unit is compatible with multi-session.
This unit is not compatible with packet writing.
*3: UDF1.02 without ISO9660, UDF1.5 with ISO9660.
*4: UDF2.5.
*5: Maximum number of folders recognizable:300 folders.
(including the root folder)
Maximum number of files recognizable:200 files.
*6: MPEG-4 ASP. Lecel 4. AAC-LC, MP3, Dolby Digital audio,
DTS and PCM can be decoded.
*7: DivX Certified to play DivX video up to HD 1080p, including
premium contrnt.
GMC(Global Motion Compensation) is not supported.
USB device:
USB Standard: USB2.0 High Speed
Format: FAT12, FAT16, FAT32, MP3,
JPEG, MKV, DivX
Contents:
JPEG:
CD-R/RW, BD-RE, DVD-R,USB device:
Pixcels: 34x34~8192x8192
Sub Sampling: 4:2:2, 4:2:0
Motion JPEG not supproted
Maximum numbers of folders and files:
*8: Total of the JPEG.
MP3:
CD-R, CD-RW, DVD-R, USB device:
Compression rate: 32kbps~320kbps
Sampling rate: 44.1kHz, 48kHz
AVCHD (H.264):
DVD: AVCHD format V1.0
HDMI: 480p(525p)/576p(625p)(BD75GA/
GC/GN/GT/GW)/1080i(1125i)/
720p(750p)/1080p(1125p)
HDMI (V.1.4a)
(This unit supports “HDAVI
Control 1” function.)
Playable discs

11
BD-ROM(SL/DL):
(SL:Single Layer/DL;Dual Layer)
compliant Ver.1.3
BD-RE(SL/DL):
(SL:Single Layer/DL;Dual Layer)
BD-MV
BD-R(SL/DL):
(SL:Single Layer/DL;Dual Layer)
BD-MV
DVD-ROM(SL/DL):
(SL:Single Layer/DL;Dual Layer)
DVD-Video
DVD-R: DVD-Video
DVD-VR
DVD-R(DL): DVD-Video
DVD-VR
DVD-RW: DVD-Video
DVD-VR
+R: Video
+R(DL): Video
+RW: Video
CD: CD-DA, CD-Video, CD-R/RW
Optical pick-up: System with 2 lenses
Wave length: 790 nm(CDs) 655 nm(DVDs)
405 nm(BDs)
LASER specification
Class 1 LASER Product
Wave length: 790 nm(CDs) 655 nm(DVDs)
405 nm(BDs)
Laser power: No hazardous radiation is emitted
with the safety protection
Playable discs
BD-ROM(SL/DL):
(SL:Single Layer/DL;Dual Layer)
compliant Ver.1.3
BD-RE(SL/DL):
(SL:Single Layer/DL;Dual Layer)
BD-MV
BD-R(SL/DL):
(SL:Single Layer/DL;Dual Layer)
BD-MV
DVD-ROM(SL/DL):
(SL:Single Layer/DL;Dual Layer)
DVD-Video
DVD-R: DVD-Video
DVD-VR
DVD-R(DL): DVD-Video
DVD-VR
DVD-RW: DVD-Video
DVD-VR
+R: Video
+R(DL): Video
+RW: Video
CD: CD-DA, CD-Video, CD-R/RW
Optical pick-up: System with 2 lenses
Wave length: 790 nm(CDs) 655 nm(DVDs)
405 nm(BDs)
LASER specification
Class 1 LASER Product
Wave length: 790 nm(CDs) 655 nm(DVDs)
405 nm(BDs)
Laser power: No hazardous radiation is emitted
with the safety protection
Dimensions:
430mm(W)
35mm(H)
179mm(D)
(excluding the projecting parts)
185mm(D)
(including the projecting parts)
Mass: Approx. 1.6 kg
Solder: This model uses lead free
solder(PbF).
Note: Specifications are subject to
change without notice.

12
5 Service Mode
5.1. Self-Diagnosis and Special Mode Setting
5.1.1. Self-Diagnosis Functions
Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has
occurred.
U** and F** are stored in memory and held.
You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode.
Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is ON.
Error Code Diagnosis contents Description Monitor Display Automatic FL display
U30 Remote control code error Display appears when main unit and remote
controller codes are not matched.
No display
* is remote controller code of the
main unit.
Display for 5 seconds.
U59 Abnormal inner temperature
detected
Display appears when the drive temperature
exceeds 70°C.
The power is turned off forcibly.
For 30 minutes after this, all key entries are
disabled.
The event is saved in memory as well.
No display
U59 is displayed for 30 minutes.
U71 HDMI incompatible error
(HDMI incompatible)
Display this error when the equipment (com-
patible with DVI such as TV, amplifier etc.)
connected to the unit by HDMI is incompatible
with HDCP (High-bandwidth Digital Content
Protection).
No display
U72 HDMI connection error
(communication error)
This error is displayed when there are any
communication problems with the unit and the
equipments (TV, amplifier etc.) connected to
the unit by HDMI. (or when there is a problem
with the HDMI cable)
The display disappears only when the con-
nection is released. Neither the button opera-
tion nor the passage of the fixed time
disappear the display.
No display
U72 display disappears when
error has been solved by Power
OFF/ON of connecting equipment
or by inserting/removing of HDMI
cable.
U73 HDMI connection error
(authentication error)
When authentication error occurs while the
equipments (TV, amplifier etc.) are connected
by HDMI. (or when there is a problem with the
HDMI cable)
The display disappears only when the con-
nection is released. Neither the button opera-
tion nor the passage of the fixed time
disappear the display.
No display
U73 display disappears when
error has been solved by Power
OFF/ON of connecting equipment
or by inserting/removing of HDMI
cable.
U76 Connection error Display this error when the equipment (com-
patible with DVI such as TV, amplifier etc.)
connected to the unit by HDMI is incompatible
with HDCP (High-bandwidth Digital Content
Protection).
No display
U77 Illegal disc error This error is displayed when it becomes
impossible to reproduce because of copyright
illegal information.
No display
U88 Restoration is operation.
(When the disc is in the disc
tray)
This error is displayed when there is a disc in
the disc tray or abnormality is confirmed dur-
ing playback. It is shown that the restoration
to return the main unit operation normally is
operating. It becomes possible to use as soon
as not the breakdown but the U88 display dis-
appears.
No display
Display for 30 seconds.
F00 No error information Initial setting for error code in memory
(Error code Initialization is possible with error
code initialization and main unit initialization.)
No display No display
F34 Initialization error When initialization error is detected after start-
ing up main microprocessor, the power is
turned off automatically.
The event is saved in memory.
No display No display

13
F58 Drive hardware error When drive unit error is detected, the event is
saved in memory.
No display No display
F74 HDMI Device Key Communica-
tion error.
This error is displayed when the information
error is occurred at HDMI device key loading.
No display
F75 HDMI incompatible error
(HDMI incompatible)
Display this error when the equipment (com-
patible with DVI such as TV, amplifier etc.)
connected to the unit by HDMI is incompatible
with HDCP (High-bandwidth Digital Content
Protection).
No display
F99 Hang-up Displayed when communication error has
occurred between Main microprocessor and
Timer microprocessor.
No display
Displayed is left until the [POWER]
key is pressed.
UNSUP-
PORT
Unsupported disc error *An unsupported format disc was played,
although the drive starts normally.
*The data format is not supported, although
the media type is supported.
*Exceptionally in case of the disc is dirty.
“This disc is
incompatible.”
It is displayed for 5 seconds.
The character indication flows
sideways.
NO READ Disc read error *A disc is flawed or dirty.
*A poor quality failed to start.
*The track information could not be read.
“Cannot read.
Please check the
disc.”
HARD
ERR
Drive error The drive detected a hard error. “BD drive error.”
It is display for 5 seconds.
The character indication flows
sideways.
SELF
CHECK
Restoration operation Since the power cord fell out during a power
failure or operation, it is under restoration
operation.
*It will OK, if a display disappears automati-
cally. If a display does not disappear, there is
the possibility that defective Digital P.C.B. /
BD Drive.
No display
The character indication flows
sideways.
UNFOR-
MAT
Unformatted disc error This error is displayed when the unformatted
DVD-RAM or DVD-RW recorded by another
make of recorder is inserted.
No display
This disc is not formatted properly.
Format the disc in DISC MAN-
AGEMENT?
PLEASE
WAIT
Unit is in termination process Unit is in termination process now.
“BYE” is displayed and power will be turned
off.
No display
The character indication flows
sideways.
No PLAY When there is a viewing restric-
tion on a BD-Video or
DVD-Video.
Rating password is set. No display
Error Code Diagnosis contents Description Monitor Display Automatic FL display

14
5.1.2. Special Modes Setting
Item FL display Key operation
Mode name Description Front Key
Rating password The audiovisual level setting password is
initialized to Level 8. While the unit is on, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds.
- "00 RET" is displayed on the unit's
display.
Repeatedly press [ ] on the
remote control or [POWER] on the
unit until "03 VL" is displayed on the
unit's display.
Press [OK] on the remote control
or [OPEN/CLOSE] on the unit.
Service Mode Setting every kind of modes for servicing.
*Details are described in 7.1.3. (BD) Service
Mode at a glance.
Turn the power on.
Press the [5] [9] and [R] button
simultaneously for five seconds,
then [70 RET] is displayed on FL.
Press the [ ] button to select
until [80 SRV] is displayed on FL.
Press the [OK] button .
*The command is transmitted by
attached remote control.
BD-ROM history cleaning < Persistent Storage> of BD-ROM standard is
cleaned. When the power is on, disc is not
in tray, press and hold [6], [7] and
[Y] on the remote control at the
same time for more than 5 seconds.
- "50 RET" is displayed on the unit's
disply.
Repeatedly press [ ] on the
remote control or [POWER] on the
unit until "51 NOP" is displayed on
the unit's display.
Press and hold [STOP] on the
remote control until "52 BRE" is
displayed on the unit's display.
Press [OK] on the remote con-
trol or [OPEN/CLOSE] on the unit.
Forced disc eject Removing a disc that cannot be ejected.
While Demonstration Lock is being set, this
Forced disc eject function is not accepted.
While the unit is on, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds.
- "00 RET" is displayed on the unit's
display.
Repeatedly press [ ] on the
remote control or [POWER] on the
unit until "06 FTO" is displayed on
the unit's display.
Press [OK] on the remote control
or [OPEN/CLOSE] on the unit.
Forced power-off When the power button is not effective while
power is ON, turn off the power forcibly.
Display in P-off mode. Press [POWER] key over than 4
seconds.

15
Aging Perform sequence of modes as * Aging
Description shown below continually.
Display following the then mode. Turn the power on.
Press the [5] [9] and [R] button
simultaneously for five seconds,
then [70 RET] is displayed on FL.
Press the [ ] button to select
until [81 AIG] is displayed on FL.
Press the [OK] button .
*The command is transmitted by
attached remote control.
NOTE1:
If the unit has hung-up because of
pressing keys for over 10 seconds,
once turn off the power, and re-exe-
cute this command.
*When releasing Aging mode, press
[POWER] key over 4 seconds.
Item FL display Key operation
Mode name Description Front Key

16
Demonstration
lock/unlock
Ejection of the disc is prohibited.
The lock setting is effective until unlocking the
tray and not released by Main unit
initialization of service mode.
*When lock the tray.
“LOCK” is displayed for 3 seconds.
When the power is on, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds. - "00 RET" is dis-
played on the unit's disply.
Repeatedly press [ ] on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [STOP] on the
remote control until "10 OCL" is
displayed on the unit's display.
Press [OK] on the remote con-
trol or [OPEN/CLOSE] on the unit.
*When unlock the tray.
“UNLOCK” is displayed for 3 sec-
onds.
When the power is on, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds. - "00 RET" is dis-
played on the unit's disply.
Repeatedly press [ ] on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [STOP] on the
remote control until "10 OCL" is
displayed on the unit's display.
Press [OK] on the remote con-
trol or [OPEN/CLOSE] on the unit.
*When press [OPEN/CLOSE] key
while the tray being locked.
Display LOCK for 3 seconds.
Press [OPEN/CLOSE] key while the
tray is being locked.
Progressive initialization The progressive setting is initialized to Inter-
lace. When the power is on, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds. - "00 RET" is dis-
played on the unit's disply.
Repeatedly press [ ] on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [OK] on the
remote control or [OPEN/CLOSE]
on the unit.
Default setting The date of Menu, Mode and EEPROM
setting, etc. is set to the default condition in
factory.
While the unit is on, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds.
- "00 RET" is displayed on the unit's
display.
Repeatedly press [ ] on the
remote control or [POWER] on the
unit until "08 FIN" is displayed on
the unit's display.
Press and hold [OK] on the
remote control or [OPEN/CLOSE]
on the unit for at least 3 seconds.
Item FL display Key operation
Mode name Description Front Key

17
5.1.3. Service Modes at a glance
Information necessary for service can be displayed.
Service mode setting:
1. Turn the power on.
2. Press the [5] [9] and [R] button simultaneously for five seconds, then [70 RET] is displayed on FL.
3. Press the [ ] button to select until [80 SRV] is displayed on FL.
4. Press the [OK] button.
5. It is displayed on FL as [HELLO-->SERV].: It is shown to have entered the service mode.
6. The command is transmitted by attached remote control.
Method of making clear service mode: Press the power button (power off).
The display of information to each command is as follows.
NOTE:
Do not use it excluding the designated command.
Item FL display Key operation
Mode name Description (Remote controller key)
Release Items Item of Service Mode executing is cancelled. Press[0][0] or [Return] in service
mode.
Error Code Display Last Error Code of U/F held by Timer is dis-
played on FL.
*Details are described in
7.1.1. Self-Diagnosis Functions.
If any error history dose not exist,
[F00] is displayed.
Press [0] [1] in service mode
ROM Version Display The display contents are switched over every
5 seconds.
1. Region code
2. Main firm version
3. Boot View version
4. Timer firm version
5. Drive firm version
Press [0] [2] in service mode
Laser Used Time
Indication
Check laser used time (hours) of drive.
(****) is the used time display in
hour.
Laser used time of BD/ DVD/ CD
in Playback mode is counted.
Press [4] [1] in service mode.

18
BD drive last error BD drive error code display. 1. Error Number is displayed for 5
seconds.
2. Time when the error has occurred
is display for 5 seconds.
YY: Year
MM: Month
DD: Day
3. Last drive error (1/2) is displayed
for 5 seconds.
00 : Bad disc
03 : Bad disc
04 : Bad disc or drive malfunction
4. Last drive error (2/2) is displayed
for five seconds.
5. Error occurring disc type is dis-
played for 5 seconds.
Press [4] [2] in service mode.
Item FL display Key operation
Mode name Description (Remote controller key)

19
6. Disc maker ID is displayed for 5
seconds.
7. Factor of drive error (hexadeci-
mal) occurring is left displayed.
In case that the maker cannot be
identified, display is blackout.
Item FL display Key operation
Mode name Description (Remote controller key)

20
8. When the last error doesn't exist .
CEC (H) output The CEC terminal high output of HDMI. Press [5] [5] in service mode.
CEC (L) output The CEC terminal low output of HDMI. Press [5] [6] in service mode.
Manufacturing Date Read out the manufacturing date of the unit.
YY: Year
MM: Month
DD: Day
Press[6][1]in service mode.
Tray OPEN/CLOSE Test The BD drive tray is opened and closed
repeatedly.
*is number of open/close cycle
times.
Press [9] [1] in service mode
*When releasing this mode, press
the [POWER] button of Remotes
Controller more than 10 seconds.
Delete the Laser Used
Time
Laser used time information stored in the
memory of the unit is deleted.
Press [9] [5] in service mode.
Delete the Last Drive
Error
Laser Drive Error information stored on the
BD Drive is deleted.
Press [9] [6] in service mode.
Delete the Error History Error History information stored on the unit is
deleted.
Press [9] [7] in service mode.
Initialization of the Error
code
Last Error Code information stored by timer is
deleted. (Write in F00)
Press [9] [8] in service mode.
Initialization of the
Service Mode
Last Drive Error, Error History and Error code
information stored on the unit are initialized to
factory setting.
Press [9] [9] in service mode.
Release Service Mode Release Service Mode and turns the Power
Off.
Display in STOP (SS) mode.
Press [POWER] button on the front
panel or Remote controller in ser-
vice mode.
Item FL display Key operation
Mode name Description (Remote controller key)