Panasonic DMP-BDT310 User manual

PanasoniC
Owner's
Manual
Blu-ray
Disc™
Player
«·>
TM
B/u·ragD/sc
Panasonic
The illustration shows the image
of
DMP-BDT310.
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully.
Model
No.
DMP-BDT310
DMP-BDT215
DMP-BDT210
DMP-BDT110
Before connecting, operating
or
adjusting this product, please read the instructions completely.
Pl
ea
se
keep this manual for future reference.
If
you have any questions contact
U.S.A. and Puerto Rico : 1-800-211-PANA(7262)
Canada : 1-800-561-5505
VQT3B58-1

IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow
the safety instructions on the unit and the applicable safety instructions
listed below. Keep these operating instructions handy for future reference.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus
near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8 Do notinstall nearany heatsources such as radiators,
heat registers,
stoves,
or otherapparatus (including amplifiers) that produce heat.
9 Do notdefeatthe safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding-type plug has two bladesand a third grounding prong. The
wide blade or the third prong are provided foryour safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement
of the obsolete outlet.
10 Protect the power cord from being walked on or pinched partcularlyat plugs,
convenienoe reoeptacles , and the pointwhere th ey exitfrom the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket,or table <I
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Referall servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supplycord or plug isdamaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
I WARNING
Unit
To reduce th e risk of fire, elec tr ic shock or producl damage,
-Do not expose this unit to rain, moisture, dripping or splashing.
-Do not place objects filled with liquids, such as vases, on this unit.
-Use only the recommended accessories.
-Do not remove covers.
-
Do not repair this unit by yourself. Referservi ci ng to qualified servioe personn e l.
Unit
-This unitutilizes a laser. Use of controls or adjustments or performance
of procedures otherthan those specified herein may result in
hazardous radiation exposure.
Do not place sources of naked flames, such as lighted candles, on this unit.
Placement
To reduce the risk of fire, electric shock or product damage,
Do not install or place this unit in a bookcase, built-in cabinet or in
anotherconfined space. Ensure this unit is well ventilated.
-Do not obstruct this unit's ventilation openings with newspapers,
tablecloths, curtains, and simi
lar items.
2 VQ T3 B5 8
CAUTION- ~ ~ ~ ~ ~ f~~ Y ~~E ~ ~ER RAD IA l ~ ~ ~ ~ ~ ~ ~:~N ri ( ll a)
CAUTION- ~i~~ ~~ :~~~ N ~~~:r~ H E I ~ =1 , t A2 1 CtASS 1 M
ATI E NTION- ~ ~ = ~ ~: . VI S IBLE ET INV ~ IBL E, CLASSE '" ·
NE PAS AE GAROER DIREC TEME NT A L' AI DE O'I N STRIJMENTS D'OPT10U E.
FoRsiGTIG- m~ ~~~ , ~~ ~ ~~ iT ~:
6
~~ ~ ~ ~ ~ ~ ~ - ~ ~ " 'f ~: T '"
VARO - ~~s:..~ T A LT T IIN A L UOKA N 1MNA KYVAA JA NAKYMA TONTA
ALA KA T SO OPTISEUA LA tiT EELlA SUO RAA N S.i.TE E SEEN
VARNING- ~ ~ ~~~~~=~~~~~~ ~~~ ~~ ~ ~ A ~~/:r.
voRS I CHT - ~~ ~~eAci ~~B~~ ~ S ~~~ ~ LA S ER ST RAHLU NG KtAss e 1M.
NICHT DIA E KT MIT O PTI SC HEN IN ST AUM E NT EN BETR AC HT EN.
(Inside of product)
THE FOLLOWING APPLIES ONLY IN THE U.S.A. AND
CANADA.
CAUTION : TO REDUCETHERISK OF ELECTRIC
SHOCK,DO NOTREMOVE SCREWS.
NOUSER-SERVICEABLEPARTS
INSIDE.
REFERSERVICINGTO QUALIFI
ED
SERVICE PERSONNEL
The lightning flash with arrowhead symbol, within an
A equilateral triangle, is intended to alert the user to the
presence ofuninsulated "dangerous voltage" within
the product's enclosure that may be ofsufficient
magnitude to constitute a risk
of electric shock to persons.
AThe exclamation point within an equilateral triangle
is
intended to alert the userto the presence of important
operating
and maintenance (servicing) instructions in
the literature accompanying the appliance.
IFor units with PX printed on the outer packagingI
THIS UNIT IS INTENDED FOR USE IN MODERATE CLIMATES.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits ar e designed to provide reasonable protection agai nst harmful
interference in a residential installation. This equipment
gene rates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occurin a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on,
the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient
or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connectthe equipment into an outlet on a cir cuitdifferent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, follow the attached
installation instructions and use only shielded interface cables when
connecting to peripheral devices.
Any changes
or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject
to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must acc ept any interference
received, including interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation
of North America
One Panasonic Way,
Se caucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No .: 1-800-211-PANA (7262)

Table
of
contents
Getting started
IMPORTANT SAFETY
INSTRUCTIONS
................
2
Accessories
....................
4
Unit and media care
.............
4
Control reference guide
..........
5
Playable discs/Cards/USB devices. . 6
Connections
&
Settings
STEP 1 : Connecting to a TV
......
8
STEP 2 : Connecting to an amplifier/
receiver
.....
.
.........
9
STEP 3 : Connecting to a broadband
network
..........
..
..
10
STEP 4 : Connecting to an AC power
source
...............
12
STEP 5 : Settings . . . . . . . . . . . . . .
12
Playback
Inserting
or
removing media
......
16
HOME menu .
.................
16
Playing video contents . . . . . . . . . .
17
Enjoying 3D video. . . . . . . . . . . . . .
20
Playing still pictures
............
21
Playing music
.................
22
Enjoying VIERA CAST™
.........
23
Playing contents saved
on
other
equipment
....................
24
Linked operations with the
TV
(VIERA Link™ "HDAVI Control™")
......
26
Settings
Playback menu
.................
27
Setup menu
...................
29
Reference
Troubleshooting guide
...........
34
Messages
.....................
37
Supplemental information
....
.
...
38
Specifications
....
.
.............
39
Limited Warranty (ONLY FOR U.S.A.
AND PUERTO RICO)
...........
41
Limited Warranty
(Only for CANADA)
.............
42
Referencia rapida
en
espariol
(Spanish Quick Reference)
[Para EE.
UU
.
y
Canada) . .
..............
43
Index
..........
.
......
Back cover
About
descrip~ion!
f
irl'this
Ow~
!
!;
s
·
Manual ·
··'"
•
lnstru
e
tion~
tor
operati
6n
s aregenerany:d
es
G
rl
bed .
~'l'
" ' '
f'l<l
'9!
~
i""
.:<'
•"
" '
I ,
!'~
t'
, '
using·tl'le rernote controt.
··
'·
•!•
:·;
·,
::"
·
·
"'
-__
-_
,_
-"'
_ r : ·
,"'1''
~
.}••
•
'•
·'
"'
-
"' ".
--_
·
~
_
,·
'
'·tHI
•}•
ci!;~
(.?';}'
·'
'
I
•;
Ttl!
:s
.
$:}
W~~t
r
$
k
Ma
~~
:a
~
i
:
s
-
~
-
af)-pti;~bl
~
:
~q
:
m9~
t
s
-
~·%
_
,;
-~-~-
0
.DMP
:.
BOT310,
OMP
-
BOT2
~
5
DMP£
0T210.and
•
____
- -
;:
_ ' _ -'"'
_
-~
-
-) , • _
-·:
-
'J;
>i!i'$
W'~
·
:
:!'
_ •
-<c
DMP
~
BDT11
0. Unless
.
oth~f!iise
indicate
.5f.:
Htustrations
in this.
owner's
Manl,!al are
of
DMPd30.1'$j
fl..
•,
....
;'!('
• __
,..
' " ·"
'•'
.
't
-
~
' .
'0'''"'
__ .
~
-~
;
-
~
I
aora1o
t
i
.
BDT215
U
BDT2~o
. l l
aDT1.1o
L
:
Jh!;fj
'
~
te
J>
.feature
,
s
appti~~bte
.
to
DMi?
~
st5
T:3t
o
:
,
QMl?
t
~
'
:
.~
J5
;
r
;
. .
,;
· ' .
·o·
M
·,
_
"'
p·-, ,.;;,
"s'
-;0
--
,,...,2
.-
"1·o
··
'·
·
"'
,
--
t
.d
.,
~
:
·o·:,
"M"
_,
_m
·~-
B
-
~
6.~
-
1
°
1
-
;
~
r\
:
r:
:;
1
:
::
;~~'
;iii
·
li:
-
,'3!,
_,.
1-
'f.
.·
:. ;
..,
.
,;..
. , ,, · . an · .
..
,:;.
.;;
'"'·';,.
v
; r
~
f:!
;
. y:
""
'·'~-·
,.
'"'
;»
_
,-:;
-:»
: .
i
~·
fi
Iii:
:;!
/
,;
"'
VQT3B58 3

Accessories
Check the supplied accessories before using this unit.
1 Remote
control
(N2QAYB000574)
2
Batteries for remote control
1 AC power supply cord
I For U.S. A. and CanadaI
(K2CB2CB00022)
I For units with PX printed on the outer packaging I
(K2CQ2CA00007)
1 I For units with PX printed on the outer packaging I
AC plug adaptor
(K2DAYYY00002)
1 IBDT215I HDMI cable
(K1 HY19YY0012)
I For CanadaI
The enclosed Canadian French label sheet corresponds to the English
display on the front and back side
of the unit.
w
• Product numbers provided in this Owner's Manual correct as of
December 2010. These may be subject to change.
• Do not use
AC power supply cord with other equipment.
• I For U.S.A. and Puerto Rico I: To order accessories, refer to
"Accesso Purchases (United States and Puerto Rico)" on page 41.
For other areas : To orderaccessories, call the dealer from whom
you have made your purchase.
Insert so the poles(+ and -)match those in the remote
control.
R6/LR6,AA
(Alkaline or
manganese batteries)
Point it at remote control signal sensoron this unit.
(Q 5)
m
Mishandling of batteries can cause electrolyte leakage which can da mag e
items the fluid contacts and may cause a fire.
• Do notmix old and new batteries
or different types at the same time.
• Do not heat
or expose toflame.
• Do not leave the battery(ies) in a carexposed to direct sunlight fora
long period
of time with doors and windows closed.
• Do nottake apart
or short circuit.
• Do notattempt to recharge alkaline
or manganese batteries.
• Do not use batteries
if the covering has been peeled off.
Remove batte
ri es if th e remote control is not going to be used fo r a long
period oftime. Store
in a cool, dark place.
CAUTION
• Danger of explosion if battery is incorrectly replaced. Replace only
with the type
re commended by the manufacturer.
•
Wh en disposing the batteries, please contact your local authorities
ordealer and ask forthe correct method
of disposal.
4 VQT3B58
Unit and media care
• Clean this unit with a soft, dry cloth
• Never use alcohol, paint thinner or benzine to clean this
unit.
• Before using chemically treated cloth, carefully read the
instructions that came with the cloth.
• Clean the lens
• Use the lens cleaner (not supplied) to clean the unit's lens.
• Clean discs
DO DONOT
@I/~
Wipe with a damp cloth and then wipe dry.
• Disc and card handling precautions
• Handle discs by the edges to avoid inadvertent scratches
or fingerprints on the disc.
• Do not attach labels
or stickers to discs.
• Do not use record cleaning sprays, benzine, thinner, static
electricity prevention liquids
or any other solvent.
• Clean any dust, water, orforeign matterfrom the terminals
on the rear side
of the card.
• Do not use the following discs:
-Discs with exposed adhesive from removed stickers
or
labels (rented discs etc).
-Discs that are badly warped or cracked.
-Irregularly shaped discs, such as heart shapes.
• To dispose or transfer this unit
The unitmay keep the usersettings information in the unit. If
you discard this unit eitherby disposal
or transfer, then
follow the procedure to return all the settings to the factory
presets to delete the usersettings.
(Q 34, "To return all
settings to the factory preset.")
• The operation history may be recorded in the memory
of
this unit.

Control
reference
guide
1
2
.-------9
~
1
~
1m
!il
1o~~-1o
liJ
--11
-1
+
~
I
INPUT
VOL
DI
SPlAY
....
~
-
0
i
i
---------------
-
~
0 J
!GiJ [
2Asc
][
3oEF
]!
CJ
--12
:(4;]~~~
I
!
4GHI
5JKL
0
6MN
O •
3
--;--"1
I
CJ
-~
13
![
78Rs
J
[
8ruv
J
[
9~
v
z
]j
[u
010
-J
--14
~
lcANffil
f(jl
fill
:
NETFLIX
I
~
~
l.!:::!J
: 0
--15
~-----------------
1
Turn the unit on and off
2 TV operation buttons
You
can operate the Panasonic TV through the unit's
remote control. (Depending on the TV these buttons
may not work.)
[<9
TV POWER] : Turn the television
on
and off
[AV]
: Switch the input select
[+ -
VOL] : Adjust the volume
3 Select title numbers, etc./Enter numbers or characters
(~
23)
[CANCEL] : Cancel
4 Basic playback control buttons (
~
17)
5 Show status
messages(~
17)
6 Show Pop-up menu/Top menu/Direct
Navigator(~
17)
7 Show sub menu
(~
18)
8 These buttons are used when;
• Operating a BD-Video disc that includes Java™
applications (BD-J).
• Operating contents
of
VIERA CAST.
(~
23)
9 Transmit the remote control signal
10
Open or close the disc tray (
~
16)
CAUTION
Do
not place objects in front of the unit. The disc tray
may collide with objects when it is opened, and this may
cause malfunction.
11
Show Playback
menu(
~
27)
12
Start
up
a video
communication(~
23)
13
Setup
30
effects(~
20)
14
Select
audio(~
17)
15
Show NETFLIX screen
16
Exit the menu screen
17
Displays the Home screen
of
the VIERA
CAST(~
23)
18
Show HOME
menu(~
16)
19
Selection/OK,
Frame-by-frame(~
17)
20
Return to previous screen
[
~
]6
q
:
~"== 1 1
~
=====:JJ
I
~
~h
~ I
Tf
Pull to flip down
the front panel.
1 2 3
4
57
POWER button
(POWER
<9/1)
(~
12)
Press to switch the unit from on to standby mode
or
vice
versa.
In
standby mode, the unit is still consuming a
small amount of power.
2 Disc
tr
a
y(
~
16)
3 SO
ca
rd
slot(
~
16)
4 USB
port(~
16)
5
IBDT310I:
V.OFF
LED
(Video offLED)
It
is
possible to set the LED to turn on/off.
(
~
31)
6 CALL
L
E
D(
~
23)
The LED will light
up
when this unit receives incoming
call etc. of the video communication.
8
910
11
7 Remote control signal sensor
Distance: Within approx. 7 m (23 feet)
Angle: Approx.
20°
up and down,
30°
left and right
8 Display
9
Stop(
~
17)
10
S
ta
rt
pl
a
y(
~
17)
11
Open or close the disc tray (
~
16)
12
IBDT31oliBDT215I IBDT210I :
Touch Free
Sensor(
~
33)
The LED will light up when TOUCH-FREE SENSOR
is
activated.
Rear panel
termin
a
l
s
(
~
8--10, 12)
VQT3B58 5

Playable discs/Cards/USB devices
Type ILogo examplesI Type detail I Playable contents
(~
39)
BD-Video Video
Video
BD-RE
JPEG/
lm1
~
MPO
(30
still picture)
B/u·rayD/sc
Video
BD-R DivX®
I
BDT310/210
for
Canada
I
MKV
DVD.
DVD-Video Video
VIDEO
~
Video
DVD-R
AVCHD
R
R4
.7
DivX®
!
BDT310/21
o
for
Canada
I
MKV
1•11•1
!00?
MP3
R
DVD-R DL JPEG/
RDL
MPO
(30
still picture)
ore
DVD-RW
Video
RW
AVCHD
-+R/+RW/+R DL
rn1o~@
Music
CD
Music [CO-DA]
DIGITAL
AUDIO
DivX®
I
BDT310/210
for
Canada
I
mJ
MKV
CD-R
Music [CO-DA]
-
CD-RW
MP3
JPEG/
MPO
(30
still picture)
SD Memory Card (from
8MB
to
2GB)
MPEG2
m
S;~i~
'"
SDHC
Memory
Card
(from
4
GB
to
32
GB) AVCHD
...XC:
SDXC Memory Card (48
GB,
64
GB)
JPEG/
(Compatible with both mini and micro types) MPO
(30
still picture)
DivX®
I
BDT310/210
for
Canada
I
USB devices
MKV
11~1=J
-(up to 2
TB)
MP3
JPEG/
MPO
(30
still picture)
6
VQT3B58

• Discs that cannot be played in this
unit
Any other disc that is not specifically supported or
previously described.
• DVD-RAM
• Super Audio CD
• Photo CD
• DVD-Audio
• Video CD and Super Video CD
• WMA discs
• IBDT31 0/210 for other than Canada II BDT215II BDT110 I :
All types of DivX discs
IBDT310/210 for Canada I: DivX Plus HD discs
•
PAL discs
•
HD DVD
• BD-Video discs recorded at a rate
of 50 fields/sec
• Region management information
BD-Video
This unit plays BD-Video marked with labels containing the
region code "A".
Example:
DVD-Video
This unit plays DVD-Video marked with labels containing the
region number
"1" or "ALL".
Example:
• Finalize
DVD-R/RW/R DL, +R/+RW/+R DL and CD-R/RW recorded
by a recorder, etc. needs
to be finalized by the recorder to
play
on this unit. Please refer to the recorder's instructions.
• BD-Video
• This unit supports high bit rate audio (Dolby Digital Plus,
Dolby TrueHD, DTS-HD High Resoluiion Audio and
DTS-HD Master Audio) adopted
in BD-Video.
- IBDT110 I : If "Dolby D/Dolby D +/Dolby TrueHD" is set to
"PCM", the maximum possible numberof Dolby sound
is
5.1 ch PCM. (~ 30)
• 30
• 30 videos and 30 still pictures can be played back when
this unit
is connected to a 30 compatible TV using a High
Speed HDMI Cable.
•
20 video can be enjoyed as 30 virtually. (~ 20)
• Music CD
• Operation and sound quality of COs that do not conform to
CO-DA specifications (copy control CDs, etc.) cannot be
guaranteed.
• The digital audio content side
of a DualDisc does not meet
the technical specifications
of the Compact Disc Digital
Audio (CD-DA) format
so playback may not be possible.
• SO card
• miniSD Cards, microSD Cards, microSDHC
Cards and microSDXC Cards can be used,
but must
be used with an adaptor card.
These are usually supplied with such cards,
or otherwise customer provided.
• Keep the Memory Card out of reach
of
children to prevent swallowing.
•
To protect the card's contents, move the record prevention
tab (on the
SO card) to "LOCK".
• This unit is compatible with SD Memory Cards that meet
SO Card Specifications FAT12 and FAT16 formats, as well
as SDHC Memory Cards in FAT32 format (Does not
support long file name.) and SDXC Memory Cards
in
ex FAT.
• If the SO card is used with incompatible computers or
devices, recorded contents may be erased due to the card
being formatted etc.
• Useable memory may
be slightly less than the card
capacity.
• USB device
• This unit does not guarantee connection with all USB
devices.
• This unit does not support USB device charging.
• When using Communication Camera TY-CC10W or
Wireless LAN Adaptor DY-WL10, connect it to the rear
terminal
of this unit. (~ 10, 23)
• FAT12, FAT16 and FAT32 file systems are supported.
• This unit supports USB 2.0 High Speed.
• This unit supports an HOD formatted
in FAT32. Ifthe HOD
is not recognized the power to the HOD may not be
supplied. Supply power from an external source.
m
• It may not be possible to play the above media in some cases due to the
type
of media, the condition of the recording, the recording method and
how the files were created.
• The producers
of the disc can control how discs are played, so you may
not always be able to control play as described in this Owner's Manual.
Read the disc's instructions carefully.
VQT3B58 7

STEP
1 : Connecting
to
a
TV
• Do not place the unit on amplifiers/receivers
or
equipment
that may become hot. The heat can damage the unit.
• Before making any connections we suggest you
temporarily disconnect all the units from AC power.
• Do not connect video signals through a video recorder.
Due to copy guard protection the picture may not be
displayed properly.
[8DT3101
f8DT215
1
BDT210 ·
• Via an HDMI
AV
OUT terminal (High quality)
-l]!DT310 I :
Use HOMI AV
OUT
MAIN terminal.
-It is possible to play back
30
videos and 3D still
pictures
by
connecting this unit with a
30
compatible
TV
.
HOMI cable
(Only supplied with
OMP-BOT215)
• Set "HOMI Audio Output" to
"On"(~
32).
• The HOMI connection supports VIERA Link "HOAVI
Control"(
~
26).
8 VQT3B58
• Please use High Speed HDMI Cables that have the HDMI
logo (as shown on the back cover). It is recommended that
you use Panasonic's HOMI cable. When outputting 1
080p
signal, please use HOMI cables 5.0 meters (16.4 ft.)
or
less.
Recommended part number (High Speed HDMI Cable):
RP-COHS15 (1.5 m/4.9 ft.
),
RP-CDHS30 (3.0 m/9.8 ft.),
RP-COHS50 (5.0 m/16.4 ft.), etc.
Back
of
the unit
• Via a VIDEO OUT terminal (Standard quality)
AUD
IO
IN
R l
VI
DEO
IN
(<?>
(@
(@
)
'---------
~-·-
~
~~
~
______;
f
_ Audio/Video cable
_
.,_
• Connect terminals
of
the same color.

STEP 2 : Connecting to an amplifier/receiver
• Via an HOMI AV OUT terminal
-IBDT310I: Use HDMI AV OUT
MAIN terminal.
-It is possible to play back 3D
videos and 3D still pictures when
the connected TV and amplifier/
receiver are 3D compatible.
Multi channel
speakers
Amplifier/receiver
HDMI cable
(Only supplied with
C)
DMP-BDT215)
•
Set "HDMI Audio Output" to "On"(~ 32) .
• Set "Digital Audio Output" depending
on the connected amplifier/receiver
(~ 30).
• The HDMI connection supports VIERA
Link "HDAVI Control"
(~ 26).
• When connecting to a non-3D
compatible amplifier/receiver, connect
this unit to a
TV via HDMI AV OUT,
then connect the
TV and the amplifier/
receiver, using HDMI cables forthe
respective connections.
-Please note, however, thatthe audio
can only be up to 5.1 ch.
• When using the TV
or amplifier/
receiver that does not have the
indication
of "(ARC)"
(non-ARC-compatible) on the HDMI
terminal,
in orderto enjoy TV's sound
by amplifier/receiver it is also required
to connect the amplifier/receiver and
TV using an optical digital cable.
• IBDT310 I: HDMI AV OUT SUB • Via an OPTICAL terminal
terminal
- You can enjoy richer sound by using
the HDMI
AV OUTSUB terminal.
-It is possible
to play back 3D
videos and 3D still pictures when
the connected
TV is 3D
compatible, even ifthe amplifier/
receiver is not 3D compatible.
HDMI cable
HDMI cable
Multi channel
~
speakers ~
ilc: J
Amplifier/receiver
• Set "HDMI Audio Output" to "On"
(~ 32).
• Set "HDMI(SUB) Output Mode" to
"V.OFF".
(~ 20)
-Audio is output in high resolution
regardless
of compatibility of the
amplifier/receiver with 3D.
• The HDMI connection using HDMI
AV
OUT MAIN supports VIERA Link
"HDAVI Control"
(c:::> 26).
The HDMI AV OUT SUB terminal is
notcompatible with the VIERA Link
"HDAVI Control".
Amplifier/receiver
]I
Optical cable
• When connecting a
TV(~ 8) with
HDMI AV
OUT terminal, set "HDMI
Audio Output" to "Off'
(c:::> 32).
• Set "Digital Audio Output" depending
on the used terminal and connected
amplifier/receiver(~ 30).
VQT3B58 9

STEP 3 :
Connecting
to
a
broadband
network
The following services can be used when this unit is
connected
to
broadband.
• Firmware can be updated
(Q
15)
•
You
can enjoy BD-Live
(Q
19)
•
You
can enjoy VIERA CAST
(Q
23)
•
You
can access other devices (Home Network)
(Q
24)
•
LAN
cable connection
Broadband router, etc.
Modem
(Broadband)
*Provided by ISP
--
LAN Cable
• Use category 5 or above straight LAN cables (STP) when
connecting
to
peripheral devices.
• Inserting any cable other than a LAN cable
in
the LAN
terminal can damage the unit.
10
VQT3B58
For details about connection method, refer to the
instructions supplied with the connected equipment.
• Wireless LAN connection
-I
BDT31
o
II
BDT21SII
BDT210
I:
Wireless LAN is built in.
(There is no need to connect a Wireless LAN
Adaptor.)
- I
BDT110
I:
Connect the Wireless LAN Adaptor
DY-WL10 (optional).
IBDT110
I
Wireless LAN Adaptor
LAN Cable
Modem
(Broadband)
*Provided by ISP
108ASE-
TJ
I
!XIIA.'if-TX
LAN
• For up to date compatibility information on your Wireless
router refer to
http://panasonic.jp/support/global/cs/
(This site is in English only.)
For additional information about this unit refer to
http://www.panasonic.com/consumer/support (For U.S.A.)
• The unit is not compatible with public wireless LAN
services provided in airports, stations, cafes etc.
•IBDT11ol
-Only
the Wireless LAN Adaptor DY-WL
10 (optional) can
be used.
-Read the operating instructions for
th
e Wireless LAN
Adaptor DY-WL
10 (optional) thoroughly when using
it.
-To
simultaneously connect the Wireless LAN Adaptor
DY-WL
10
(optional) and a LAN cable, use the extension
cable supplied with the DY-WL
10
.

Precautions
of
Wireless LAN connection
The following limits are
in
place regarding the usage
of
this unit or
Wireless LAN adaptor.
You
must be aware
of
these limits before using
these devices.
Panasonic will in no way
be
responsible for any incidental damage which
may
arise
due
to a failure
to
obey these limits,
or
to
any condition
of
use or
disuse
of
these devices.
• Data
transmitted
and
received
over
radio
waves
may
be
intercepted
and
monitored.
•
This
unit
or
Wireless
LAN
adaptor
contain
delicate
electronic
components.
Please use these devices in the manner
in
which itwas intended and
follow the following points:
-Do notexpose these devices to high temperatures or direct sunlight.
-Do not bend,
or
subject these devices to strong impacts.
-Keep these devices away from moisture.
-Do not disassemble or alter the device in any way.
I
BOT31
0
II
BDT215
II
BDT210I
THE FOLLOWING APPLIES IN THE U.S.A. AND CANADA
This devicecomplies with Part 15
of
FCC Rules and RSS-Gen of IC
Rules.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must
accept any interference, including interference that maycause undesired
operation
of
this device.
Contains FCC 10: VPY-LBSJ
Contains IC:772C-LBSJ
This transmitter must not be co-located
or
operated
in
conjunction with
any other antenna ortransmitter.
This product is restricted to indoor use due to its operation
in
the 5.15 to
5.25 GHz frequency range.
FCC and IC require this product to be used indoors forthe frequency
range 5.15to 5.25 GHz to reduce the potential for harmful interference
to
co-channel Mobile Satellite systems. High power radars are allocated as
primary users
of
the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands.
These radar stations can cause interference with and/ordamage this
product.
This equipment complies with FCC/IC radiation exposure limits setforth
foran uncontrolled environmentand meets the FCC radio frequency (RF)
Exposure Guidelines in Supplement C
to
OET65 and RSS-1 02
of
the IC
radio frequency (RF) Exposure rules. This equipment has very low levels
of
RF energy that itdeemed to comply without maximum permissive
exposure evaluation (MPE). But it is desirable that it should be installed
and operated keeping the radiator
at
least 20cm or more away from
person's body (excluding extremities: hands, wrists, feet and ankles).
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15
of
the FCC Rules.These limits
are designed
to
provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and,
if
not installed and used in
accordancewith the instructions, maycause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur
in
a
particular installation.
If
this equipment does cause harmful interference
to radio
or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged
to
try to correct the
interference
by
one
or
more
of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer
or
an experienced radio/TV technician for help.
FCC caution:
To
maintain compliance with FCC regulations, shielded
interface cables must be used with this equipment. Operation with
non-approved equipment or unshielded cables may result in interference
toradio and TV reception. Any changes or modifications not approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
This device complies with Part 15
of
the FCC Rules. Operation is subject
to
the following two conditions:
(1) This device may notcause harmful interference, and
(2) this device must accept
any
interference received, including
interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation
of
North America
One Panasonic Way
Secaucus,
NJ
07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-PANA (7262)
THE FOLLOWING APPLIES ONLY
IN
CANADA.
This Class B digital apparatus complies with Canadian ICES-003.
VQT3B58
11

STEP 4 :
Connecting
to
an
AC
power
source
~
AC
IN"-'
AC powersupply cord
(supplied)
To a household AC outlet
I
For units with PX printed on the outer packaging I
If
the power plug does
not
fit
~
[t:
your AC outlet, use the power
=
..
~~~
plug adaptor (supplied).
If
it still doesn't fit, contact an
electrical parts distributor for assistance.
• This unitconsumes a small amount
of
AC
power(~
39)
even when turned off. In the interest
of
power
conservation,
if
you will notbe using this unit for an
extended period
of
time, it can be disconnected.
Install this
unit
so
that
the
power
cord
can
be
unplugged
from
the
socket
outlet
immediately
if
any
problem
occurs
.
12
VQT3B58
STEP 5 :
Settings
I Easy
Setting
After connecting your new player for the 1st time and
pressing the power button, a screen for the basic settings
will appear.
Preparation
Turn on the television and select the appropriate video
input
on
the television.
1
Press
[<!>
POWER].
Setup screen appears.
If
this unit is connected to a Panasonic TV (VIERA)
supporting HDAVI Control 2
or
latervia
an
HOMI cable,
then setting information
on
the TV such as "On-screen
Language" is acquired by this unit.
2
Follow the on-screen instructions and
make the settings with
[_.,
.,.]
and press
[OK].
Aftercompleting "Easy Setting", you can perform "Network
Easy Setting".
m
•
You
can perform this setup anytime by selecting "Easy Setting"
in
the
Setup menu.
(Q
33)
Touch Free Sensor
I
BDT31
0
II
BDT215
II
BDT21
0
I
By setting "Sensor"
in
"Touch Free Sensor" to "On", you can open or close
the trayjust
by
waving yourhand over
th
e TOUCH-FREE SENSORon the
upper side
of
the unit. (This will also work when in stand-by.)
• Beawarethatthe TOUCH-FREE SENSOR
may
function unintentionally
in the following cases:
-When your hand
or
arm, an object, a small child,
or
a small animal
comes close to the upper part
of
the unit
-When an object is placed
on
top
of
the unit and vibration is applied
-When connecting a cable etc. to the rear
of
the unit
• Reactive distance
of
the sensor is automatically
set
in
accordance with
the installation conditions at
th
e time
of
power supply connection and
when the open/close button is pressed.
To
prevent
an
incorrect setting,
do
not place your hands
or
objects above the unit at these times.
• Depending on the usage conditions, the TOUCH-FREE SENSOR may
stop working
or
the reactive distance may become shorter. In such
cases, press the tray open/close button once.

I
Network
Easy
Setting
The configuration
of
your network is about to begin. If you
failed to make the settings, refer to page 14.
Wired
connection
Select "Wired" and press [OK].
LAN
cable
connect
i
on:
Connect
a
LAN
ca
ble
to
the
unit
a
nd
se
lect "Wired.'
Wireles
s
LAN
connection
:
Select
"Wireless
."
Follow the on-screen instructions to make your connection
settings.
Preparation
• Obtain your network name
(Q
15, 5510).
• If your wireless connection is encrypted please be
sure that you know your encryption
key.
• iBDT110I: If "Wireless LAN Adaptor
is
not connected." is
displayed, check that the Wireless
LAN
Adaptor is fully
inserted.Alternatively, disconnect and reconnect
it.
Ifthere
is still no change in the display, consult your dealer for
advice.
1
Select "Wireless" and press [OK].
2
Select "Search for wireless network" or
"WPS (PUSH button method)" and press
[OK] then follow the on-screen
instructions and make the settings.
•
"WPS
(PUSH
button
method)"
Ifyou are using a Wireless router that supports WPS (Wi-Fi
Protected Setup), you can easily perform the settings.
•
"Search
for
wireless
network"
The available wireless networks will be displayed.
CD
Select your network name and press [OK].
• If your network name is not displayed search again by
pressing the [R] button on the remote control. Stealth
SSID will not be displayed,
in
this case enter manually.
When your wireless network is encrypted
®
Press [OK] to select "Encryption Key".
®
Enter your encryption
key.
To
enter 5510 manually
If your SSID is not displayed
in
step
CD.
follow these steps.
1
To
display SSID input sc
re
en :
Press [HOME] Q select "Setup" Q select "Player
Settings" Q select "Network" Q [OK] Q select "Network
Settings" Q [OK] Q select "Wireless Settings" Q [OK] Q
select "Connection Setting
"Q
[OK] Q select "Manual
setting" Q [OK]
2 Press [OK] to select "SSID" and enter your SSID.
• Ifyour wireless network is encrypte
d,
go to step
@.
VQ
T3B58 13
(I)
0)
.
::
t
Q)
Cl)
""
(I)
c:
.52
-
u
Q)
c:
c:
0
(.)

When you experience
problems with settings
Wireless
Settings
A confiict
with
another device occurred.
Do you want to configure wireless network connection
setting again
?
Display
Check
the
following
A conflict with another • Please wait a few moments,
device occurred. and then try again.
• Setting
of
the Wireless router
for MAC Address etc.
A time out error • The signal
may
be weak.
occurred.
iBDT110i :
Using the USB
extension cable supplied with
the Wireless LAN Adaptor,
adjust the position
of
the
Wireless LAN Adaptor.
An authentication error • The SSID
(~
15) and the
or
a time out error encryption key
of
the Wireless
occurred. router.
• Please wait a few moments,
and then try again.
• BDT11()J:
Connection
of
Wireless LAN Adaptor
A device error occurred. • Contact our Customer
Service Centeror your
nearest dealer.
14
VQT3B58
Network
Easy
Setting
(Home
Network
Connection
Check)
1.
LAN
cable
co
nnection · Fail
2.
IP
address setting ·
Fail
3.
Connecti
on
to
gateway : Fail
r;
t.AN
u
~~
't
~j;~~
~
~~
{
c;
n
~;ct;d.
~'~-~r:~
'
'
?'<~w.
Please
c
he
ck
the
connection.
Select
"
Yes·
and
press
[OK
] to
check
network
connection
agai
n.
Select
"
No
"
and
press
[OK]
to
finish
Network
Easy
Setting.
Display
1.
LAN cable connection or
Wireless setting
2. IP address setting
3. Connection to gateway
1. LAN cable connection or
Wir
eless setting
2.
IP address setting
3.
Connection to gateway
1. LAN cable connection or
Wireless setting
2.
IP
address setting
3.
Connection to gateway
:Fail
:Fail
:Fail
:Pass
:Fail
:Fail
:Pass
:Pass
or
Home
network
available
:Fail
Check
the
following
• Connection
of
the LAN
cables
(~
1
0)
• Connection
and settings
of
the hub
and router
• Settings of
"
IP
Address/
DNS
Settings"
(~
32)
Network
Easy
Setting
(Internet
Connection
Check)
· -Connection
to
t
he
Internet
Fa
ii(Error code: 8019)
Failed the connection test.
Cannot
find
t
he
server.(Error code:
801
9)
Please
refe
r
to
t
he
owner's ma
nu
al for
the
cause
of
the
errorandthe solution for
it.
Press
[OK
].
Display
Check
the
following
Cannot find the • "Primary DNS" and "Secondary
server. DNS" settings
of
"IP Address/
(Error code: 8019) DNS
Settings
"
(~
32)
• The server may
be
busy or the
Failed to connect to service may have been
the server. suspended.
Pl
ease wait a few
(Error code: 8020) moments, and then try again.
• Settings of "Proxy Server
S
e
tt
ings"(~
32) and the router

m
• Refer to the operating instructions
of
the hub orrouter.
• WPS (Wi-Fi Protected Setup) is a standard that facilitates settings
relating to the connection and security
of
wireless LAN devices. To see
whether your Wireless router supports WPS, check the Wireless router
operating instructions.
•
You
can perform this setup anytime by selecting "Network Easy Setting"
in the Setup menu.
(
c:;>
32)
•
You
can redo these settings individually using "Network Settings".
(c:;>
32
)
• Do not use this unit or Wireless LAN adaptor to connect
to
any wireless
network for which you do not have usage rights.
During automatic searches
in
a wireless network environment,
wireless networks (SSID*) for which you do not have usage rights
may be displayed; however, using these networks
may
be regarded
as illegal access.
• After performing network settings on this unit, the settings (encryp
ti
on
level, etc.)
of
the
Wireless router might change. When you have trouble
getting on
li
ne on your PC, perform the network settings on your PC in
accordance with the settings
of
Wireless router.
• Please be aware that connecting to a network without encryption may
result in the content
of
the communication being illegitimately viewed by
a third party,
or
the leaking ofdata such as personal
or
secret
information.
I
*An
SSID (Service Set IDentification) is a name used by wireless LAN
to identify a particular network. Transmission is possible ifthe SSID
matches for both devices.
Reprogramming
the
remote
control
Ifyou have more than one Panasonic player/recorder and
the remote control operates both products at once, you will
need to change the remote control code
on
one product to
prevent this occurrence.
(~
33, "Remote Control Code")
I
Firmware updates
Occasionally, Panasonic may release updated firmware for
this unit that may add or improve the way a feature
operates. These updates are available free
of
charge.
This unit is capable
of
checking the firmware automatically
when connected to the Internet via a broadband connection.
When a new firmware version is available, the following
message is displayed.
To
update the firmware
Press [HOME]
~
select
"Setup"
~
select
"Player
Settings"~
select
"Others"~
[OK]~
select
"Firmware
Update"
~
[OK]
~
select
"Update
Now"
DO
NOT DISCONNECT the unit from the AC power or
perform any operation while the update takes place.
After the firmware is installed, "FINISH" will be displayed on
the unit's display. Unit will restart and the following screen
will be displayed.
mT
ln
~J
•
If
downloading
on
this
unit
fails
or
this
unit
is
not
connected
to
the
Internet, then
you
can
download
the
latest
firmware
from
the
follow
i
ng
website
and
burn
it
to
a CD-R
to
update
the
firmware.
http
://panasonic.
jp/support/global/cs/
(This
site
is in
English
only
.)
To
show
the
firmware
version
on
this
unit.
(
c:;>
33, "
System
Information
")
•
Downloading
will
require
several
minutes.
It
may
take
longer
or
may
not
work
properly
depending
on
the
connection
environment.
• Ifyou do not want to check for
th
e latest firmware version, set
"Automa
ti
c Update Ch
ec
k" to "Off'.
(c:;>
33)
VQT3B58 15
U)
Ol
·
==
t:
~
~
U)
c:::
.!2
-
(,)
Cll
c:::
c:::
0
u

Inserting
or
removing
media
rstil'Zfs:
[
6bT210
]
• When inserting a media item, ensure that it is facing the
right way up.
• When removing the
SO
card, press
on
the center
of
the
card and pull it straight out.
•
If
you connect a Panasonic product with a USB
connection cable, the setup screen may
be
displayed
on
the connected equipment. For details, refer to the
instructions for the connected equipment.
16 VQT3B58
HOME
menu
Major functions
of
this unit can be operated from the HOME
menu.
Preparation
Turn on the television and select the appropriate video input
on the television.
1 Press
[<9
POWER] to turn
on
the unit.
2 Press [OK] or
[•,
T,
-<1111,
...,.]
to select the
item.
• When a media is inserted, contents selection screen
for that media
is
displayed.
• If there are any other items, repeat this step.
•
To
return to HOME menu, select "HOME"
or
press
[RETURN] several times.
Disc
Videos/
Photos/ SD card
Music USB
Internet
Content
Network Home
Network
Player
Settings
Setup SD Card
Management
Wallpaper
To
show the HOME menu
Press [HOME].
Play back the contents.
(~17,21,22)
• When multiple contents are
recorded, select the types
of
contents orthe title.
Displays the Home screen
of
VIERA CAST.
(~
23)
DLNA
Client(~
24)
Media
Renderer(~
25)
(~
29)
(~
19)
Changes the screen
background
of
HOME menu.
• Items to
be
displayed may vary with the media.

Playing
video
contents
1
Insert
the
media.
If
the menu is displayed, press [.&,
T,
...,..
,
.,..]
to select
the item.
(Q
16)
2 Press
(A,
~)to
select
the
title
and
press
[OK).
When a message screen is displayed while playing back
3D compatible video software, play back
in
accordance
with the instructions.
•
To
show
menus
You can show Top Menu, Direct Navigator
or
Pop-up Menu.
Press [POP-UP MENU/TOP MENU].
• Press [.&,
T,
...,..
,
.,..]
to selectthe item and press [OK].
•
To
show
the
status
messages
While playing, press [STATUS].
The status messages give you information about what is
currently being played. Each time you press [STATUS], the
display information maychange
or
will disappearfrom the
screen.
e.g.BD-Video
T:
Title, C: Chapter, PL: Playlist
6 C Elapsed time in the title
•
T1
C1
0:05.14 0•20.52
Current position Total time
m
• DISCS CONTINUE
TO
ROTATE
WHILE
MENUS
ARE
DISPLAYED.
Press
[•STOP]
when you have finished playback to prot
ec
t the unit's
motor, yourtelevision screen and so on.
• Depending on media and contents, the display may change
or
may not
appear.
• DivX
r::l
e=o:=T
7
31'""0-:::/2
..,.
10=-f=-o
-r
c=a
-n-a
""'"
da
'l
and MKV: Successive play is not
possible.
• It is not possible
to
playback AVCHD and MPEG2 video which have
been dragged and dropped, copied and pasted to the media.
•
To
save on electricity, the power is turned
off
automatically
if
there is no
button operation for about 30 minutes
when
not playing back (such as
when paused, displaying the menu, displaying still pictures, etc.).
(Compalible with ENERGY STAR)
I
Other
operations
during
play
These functions
may
notwork depending on the media and
contents.
I Stop
---
-
------·
Press
£•STOP].
The stopped position is memorized.
Resume play function
Press [.,..PLAY]
to
restart from this position.
•
The
position iscleared ifthe tray is
opened
or
you
press
[•STOP]
several
times to display
"STOP"
on the unit's
display.
• On BD-Video discs including BD-J, the resume play
function does not work.
I Pause
-----
-----·-·-
Press
[IIPAUSE).
• Press
[IIPAUSE]
again
or
[.,.PLAY] to restart play.
~
arch/Slow-motion
Search
While
playing,
press
(SEARCH<OIIIII<OIIIII]
or
[SEARCH~~).
• Music and MP3: The speed is fixed to a single step.
Slow-motion
While
paused,
press
[SEARCH<OIIIII<OIIIII]
or
[SEARCH~~).
• BD-Video and AVCHD: Forward direction [SEARCH......]
only.
The speed increases up to 5 steps.
• Press [.,.PLAY] to revert to normal playback speed.
Skip
While
playing
or
paused,
press
[
~]
or
[
IJII+l].
Skip to the title, chapter
or
track you want
to
play.
• Each press increases the number
of
skips.
Frame-by-frame
While
paused,
press
[<IIIII)
(<IIIII
II)
or[~)
(II~).
• Press and hold to change
in
succession forward
or
backward.
• Press (.,.PLAY] to revert to normal playback speed.
• BD-Video and AVCHD: Forward direction [.,..] (II.,.) only.
Changing audio
Press
[AUDIO).
You
can change the audio channel number
or
soundtrack
languag
e,
etc.
VQT3B58
17

I
Useful
functions
1 Press [SUB MENU].
2 Select an item, then press [OK].
While Direct Navigator screen is displayed
Properties
To
display the titles properties (recording
date, etc.).
View
To
select the chapter.
Chapters
View
To
play playlists.
Playlists
View Titles
To
select the title.
Select
To
switch to another folder.
Folder
While playing
When black bars are shown at the top,
Screen bottom, left, and right sides
of
the screen,
Aspect you can enlarge the image to fill the
screen.
Top Menu
To
display
Top
Menu.
Pop-up
To
display Pop-up Menu.
Menu
Menu
To
display Menu.
2D video can be virtually output as 3D, or
3D Settings output effect
of
the 3D video can be setup.
(Q
20)
• Depending on the played contents
if
you perform "Screen
Aspect", there may be no effect.
• When "TVAspect"
(Q
31) is set to "4:3 Pan
&
Scan"
or
"4:3 Letterbox", the "Zoom" effect
in
"Screen Aspect" is
disabled.
m
• Depending on the media and contents, displayed items are different.
•
Displaying
subtitle
text
You
can display subtitle text on the
DivX
I
BDT310/210
for
Canada!and MKV video disc with this
unit. The operation might be different or it may notoperate
properly depending
on
the way the file was made orthe
state
of
this unit (playing, stopped, etc.).
Set "Subtitle" in "Disc"
(Q
27)
m
• DivX and MKV video files that
do
notdisplay "Text"
do
not contain
subtitletext.
•
If
the subtitle text is not displayed correctly, try changing the language
settings.
(
~
29)
• This function has norelation to the subtitles specified
in
DivX standard
specifications and has no clear standard.
18
VQT3B58
I
Regarding
DivX
I
BDT310/210 for Canada
I
ABOUT DIVX VIDEO:
DivX®
is a digital video format created by DivX, Inc. This is
an official DivX Certified®device that plays DivX video. Visit
divx.com for more information and software tools
to
convert
yourfiles into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND:
This DivX Certified® device must be registered
in
order to
play purchased DivX Video-on-Demand (VOD) movies.
To
obtain your registration code, locate the DivX
VOD
section
in
your device setup menu.
Go to vod.divx.com for more information on howto complete
your registration.
• Video images
of
the copyright-protected DivX contents
stored
on
USB device can
be
output only through the
HDMI output terminal.
Display the unit's registration code.
(Q
33, "DivX Registration"
in
"Others")
10 alphanumeric
characters
• After playing DivX VOD content forthe first time, the
registration code is not displayed.
• Ifyou purchase DivX VOD content using a registration
code differentfrom this unit's code, you will not
be
able to
play this content.
Cancel the unit's registration.
(Q
33, "DivX Registration"
in
"Others")
Press
[..,..,
..,..]
to select "Yes"
in
"DivX Registration".
Use the deregistration code to cancel the registration
in
www.divx.com.
Regarding DivX VOD content that can only
be played a set number of times
Some DivX VOD contents can only be played a set number
of
times. When you play this content, the number of times
already played and initially playable number of times is
displayed.
• The remaining number
of
plays decreases each time a
program is played. However,when playing from the point
where playwas previously stopped, the remaining number
of plays does not decrease due to the resume play
function.

I
Enjoying
BD-Live
or
picture-in-picture
in
BD-Video
Enjoying
BD-Live
discs
with
Internet
BD-Live allows you to enjoy more functions such as
subtitles, exclusive images and online games by connecting
this unit to the Internet. Since most
of
the BD-Live
compatible discs are played back using the BD-Live
function, additional contents are required to
be
downloaded
into the external memory (local storage).
• This unit is using an SD card as a local storage device.
BD-Livefunction cannot be used when there is no
SO
card
inserted.
1 Perform network connection and
settings.
(Q
10, 13)
2 Insert an
SO
card with 1
GB
or
more free
space.
3 Insert the disc.
•
Deleting
data/Formatting
SO
cards
Ifyou no longer need data recorded on the
SO
card, you can
delete data with the following operation.
CD
Insert an SO card.
®
Press [HOME].
@ Press [OK] to select "Setup".
@)
Press[._]
to
select "SO Card Management".
@ Press.[A,
T]
to select "BD-Video Data Erase" or
"Format
SO
Card" and press [OK].
@ Press
[..,..,
._]
to select "Yes" and press [OK].
(j)
Press
[..,..,
._]
to select "Start" and press [OK].
Playing
picture-in-picture
To
turn on/offsecondary video and audio
[DISPLAY]
9
select "Disc"
9
[~]
9
select
"Signal Type"
9
[OK]
9
set "Video" and
"Soundtrack" in "Secondary Video" to "On"
or
"Off"
Primary video
w
•
The
usable functions and the operating method
may
vary with each
disc, please refer to the instructions on the disc
and
/
or
visit their
website.
• Some BD-Live content available on
the
Blu-ray
dis
cs
may
require an
Internet account to be created in order
to
access the BD-Live content.
Follow the screen display
or
instruction manual
of
the disc for
information on acquiring an account.
•
To
use
BD-Live function,
it
is recommended that
you
format the card on
this unit.
If
the SD card you
use
is formatted, all data on the card will be
erased.
It
cannot
be
recovered.
• "
BD
-Live Internet Access" may need
to
be changed
for
certain discs
(~
29).
• When discs supporting BD-Live are played back, the player
or
disc IDs
may
be
sent
to
the content provider via the Internet.
• During search/slow-motion
or
frame-by-frame,
only
the primary video is
displayed.
• When "BD-Vi
deo
Secondary
Aud
io" in "Digital
Audio
Output" is set to
"
Off'
, secondary audio will not be
played(~
30).
VQT
3B58 19

Enjoying
30
video
You
can enjoy powerful
30
videos with realistic sensations
by connecting this unit with a High Speed HOMI Cable to a
30
compatible
TV.
The image is
an
illustration.
Preparation
Connect
30
compatible TV to an
HOM
IAV OUT terminal
of
this unit using a High Speed HDMI Cable.
(~
8,
9)
• Perform the necessary preparations for the
TV.
Method
of
playback is the same as normal disc playback.
(~
17)
• Playback following the instructions displayed on the
screen.
I
30
settings
Perform the following settings as necessary.
30
BO-Video It is also possible to play back
30
Playback discs
in
20
(conventional video).
(~
29)
If
30
video cannotbe played back
in
30,
change the settings as required
30Type
by the connected TV format. (
~
31)
• Change the settings for
30
on the
TV also when "Checker board"
or
"Side byside" is selected.
Ifthe amplifier/receiver is connected
\BDT310 \
to the
HOM
I
AV
OUT SUB terminal
HDMI(SUB)
(~
9), set to "V.OFF".
(~
31)
Output Mode •
HOM
I (SUB) V.OFF LED on this unit
will light.
(~
31)
30
Playback Hide the
30
viewing warning screen.
Precautions
(~
31)
Adjust the pop-up position for the
Pop-Out Level Playback menu or message screen
etc.(~
28)
20
VQT3B58
I
Usefu
I
functions
1
While playing
Press
[@i?).
2 Select
an
item, then press [OK].
Original Keep original picture format.
Signal Side by
30
picture format comprising of
Format side left and right screens.
20
to
30
Converts
20
pictures to
30
effect.
Normal Playback pictures with normal
30
effects.
You
can enjoy
30
pictures with a
Soft feeling
of
broadness, holding
back the depth perception.
Set
30
effect manually.
Distance
30
Set the amount
of
depth
Picture perception.
Mode Screen Type
Manual Selects how the screen appears
Settings during
30
playback (flat
or
round).
Frame Width
Set the amount
of
feathering at
the edge ofscreen.
Frame Color
Set the color
of
feathering at the
edge
of
screen.
It appears also by pressing [SUB MENU] and selecting
"30
Settings".
w
• Depending on the contents, displayed items are different.
• Please refrain from viewing
30
images
if
you
do
not feel well
or
a
re
experiencing visual fatigue.
In the event that you experience dizziness, nausea, or otherdiscomfort
while viewing 3D images, discontinue use and rest your eyes.
• Depending on the connected
1V
, the video being played back might
switch to
2D
video due to changes in resolution etc. Check the
3D
setting
on
the
TV.
• 3D images may not output as settings
of
"HOMI Resolution" and "24p
Output
"
.
(~
31)