Panasonic AJ-PX270 User manual

Operating Instructions
Excerpted Version
Memory Card Camera-Recorder
Model No. AJ-PX270
VQT5J83
FJ0214HM0 -YI
Printed in Japan
Before operating this product, please read the instructions carefully and save this manual for future use.
ENGLISH
Excerpted Version
This manual is an excerpted version of the full Operating Instructions.
For more information, please visit the Panasonic website (http://pro-av.panasonic.net/en/manual/index.
html), and refer to the Operating Instruction (PDF).
FRANÇAIS Pour de plus amples informations, visiter le site Web de Panasonic (http://pro-av.panasonic.net/en/
manual/index.html) et consulter le mode d’emploi (PDF).
ENGLISH

2
Read this rst!
Read this rst!
indicates safety information.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning ash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufcient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING:
fTo reduce the risk of re or electric shock,
do not expose this equipment to rain or
moisture.
fTo reduce the risk of re or electric shock,
keep this equipment away from all liquids.
Use and store only in locations which
are not exposed to the risk of dripping or
splashing liquids, and do not place any
liquid containers on top of the equipment.
WARNING:
Always keep memory cards (optional
accessory) or accessories (microphone
holder screws) out of the reach of babies
and small children.
CAUTION:
To reduce the risk of re or electric shock
and annoying interference, use the
recommended accessories only.
CAUTION:
Do not jar, swing, or shake the unit by its
handle while the conversion lens or another
accessory is attached.
Due to the added weight of the conversion
lens, any strong jolt to the handle may
damage the unit or result in personal injury.
CAUTION:
The mains plug of the power supply cord
shall remain readily operable.
The AC receptacle (mains socket outlet)
shall be installed near the equipment and
shall be easily accessible.
To completely disconnect this equipment
from the AC mains, disconnect the power
cord plug from the AC receptacle.
CAUTION:
Danger of explosion or re if battery is
incorrectly replaced or mistreated.
fDo not disassemble the battery or
dispose of it in re.
fDo not store in temperatures over 60°C
(140°F).
fDo not expose the battery to excessive
heat such as sunshine, re or the like.
For Battery Pack
fUse specied charger.
fReplace only with same or specied type.
CAUTION:
In order to maintain adequate ventilation,
do not install or place this unit in a
bookcase, built-in cabinet or any other
conned space. To prevent risk of electric
shock or re hazard due to overheating,
ensure that curtains and any other
materials do not obstruct the ventilation.
CAUTION:
Do not lift the unit by its handle while
the tripod is attached. When the tripod
is attached, its weight will also affect the
unit’s handle, possibly causing the handle
to break and hurting the user. To carry the
unit while the tripod is attached, take hold
of the tripod.
CAUTION:
Excessive sound pressure from earphones
and headphones can cause hearing loss.

Read this rst!
3
CAUTION:
Do not leave the unit in direct contact with
the skin for long periods of time when in
use.
Low temperature burn injuries may be
suffered if the high temperature parts of this
unit are in direct contact with the skin for
long periods of time.
When using the equipment for long periods
of time, make use of the tripod.
CAUTION (For USA and
Canada):
To prevent electric shock, match wide
blade of plug to wide slot, fully insert.
CAUTION:
Keep metal objects (such as necklaces and
hairpins) away from the battery.
Short-circuiting may occur across the
terminals, causing the battery to heat up,
and you may seriously burn yourself if you
touch the battery in this state.
CAUTION:
A coin type battery is installed inside of the
unit.
Do not store the unit in temperatures over
60 °C (140 °F).
Do not leave the unit in an automobile
exposed to direct sunlight for a long period
of time with doors and windows closed.
indicates safety information.
CAUTION:
This apparatus can be operated at a voltage in the range of 100-240 V AC.
Voltages other than 120 V are not intended for U.S.A. and Canada.
Operation at a voltage other than 120 V AC may require the use of a different AC plug.
Please contact either a local or foreign Panasonic authorized service center for assistance in
selecting an alternate AC plug.

4
Read this rst!
FCC NOTICE (USA)
Declaration of Conformity
Model Number: AJ-PX270
Trade Name: Panasonic
Responsible Party: Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102
Support contact: 1-800-524-1448
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instructions and do not
make any unauthorized modications.
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
fReorient or relocate the receiving antenna.
fIncrease the separation between the equipment and receiver.
fConnect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
fConsult the dealer or an experienced radio/TV technician for help.
The user may nd the booklet “Something About Interference”
available from FCC local regional ofces helpful.
FCC Warning:
To assure continued FCC emission limit compliance, follow the attached installation
instructions and the user must use only shielded interface cables when connecting to host
computer or peripheral devices. Also, any unauthorized changes or modications to this
equipment could void the user’s authority to operate this device.
NOTIFICATION (Canada)
CAN ICES-3(B)/NMB-3(B)
indicates safety information.
The rating plate is on the underside of the Camera Recorder, Battery Charger and AC Adaptor.

Read this rst!
5
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/ apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
For USA
A lithium ion/polymer battery that is recyclable powers the product you have purchased.
Please call 1-800-8-BATTERY for information on how to recycle this battery.

6
Read this rst!
Brazil Only
Brasil Apenas
rManuseio de baterias usadas
BRASIL
Após o uso, as pilhas e /ou baterias poderão ser
entregues ao estabelecimento comercial ou rede de
assistência técnica autorizada.
Cobrir os terminais positivo (+) e negativo (-) com uma ta isolante adesiva, antes de depositar
numa caixa destinada para o recolhimento. O contato entre partes metálicas pode causar
vazamentos, gerar calor, romper a blindagem e produzir fogo.
Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria
pode irritar a garganta, danicar o lacre do invólucro ou o vazamento provocar calor, ruptura
da blindagem e produzir fogo devido ao curto circuito dos terminais. Não incinere nem aqueça
as baterias, elas não podem car expostas a temperaturas superiores a 100°C (212°F). O gás
liberado pela bateria pode irritar a garganta, danicar o lacre do invólucro ou o vazamento provocar
calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos terminais provocado
internamente.
Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada
com bastante água. Caso haja irritação, consulte um médico.
To remove the battery
Para remover a bateria
Main Power Battery (Lithium ion Battery)
Bateria Principal de Energia
(Refer to page 25 for the detail.)
Press the battery release button.
Pressione o botão para liberar a bateria.
Battery release button
Botão de liberação da bateria
Back-up Battery (Lithium Battery)
fFor the removal of the battery for disposal at the end of its service life, please consult your
dealer.

Read this rst!
7
rBatteries that may be used with this product (Correct as of March 2014)
Panasonic VW-VBD58 batteries may be used with this product.
It has been found that counterfeit battery packs which look very similar to the genuine product are
made available to purchase in some markets. Some of these battery packs are not adequately
protected with internal protection to meet the requirements of appropriate safety standards. There
is a possibility that these battery packs may lead to re or explosion. Please be advised that we
are not liable for any accident or failure occurring as a result of use of a counterfeit battery pack.
To ensure that safe products are used we would recommend that a genuine Panasonic battery
pack is used.
Battery Charger / AC Adaptor
Disconnect the AC mains plug from the AC mains socket when not in use.

8
fSDXC logo is a trademark of SD-3C, LLC.
fHDMI, HDMI logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and/or other countries.
fMMC (Multi Media Card) is a registered trademark of Inneon Technologies AG.
fMicrosoft®and Windows®are registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
fScreenshots are used according to Microsoft Corporation guidelines.
fApple, Macintosh, Mac OS, QuickTime, iPad, and iPhone are trademarks or registered trademarks of
Apple Inc. in the United States and/or other countries.
fJava and all Java-based trademarks are trademarks or registered trademarks of Sun Microsystems, Inc.
in the United States.
fAll other names, company names, product names, etc., contained in this instruction manual are
trademarks or registered trademarks of their respective owners.
fThis product is licensed under the AVC Patent Portfolio License. All other acts are not licensed except
private use for personal and non-prot purposes such as what are described below.
-To record video in compliance with the AVC standard (AVC Video)
-To play back AVC Video that was recorded by a consumer engaged in a personal and non-commercial
activity
-To play back AVC Video that was obtained from a video provider licensed to provide the video
Visit the MPEG LA, LLC website (http://www.mpegla.com/) for details.
fUse of DCF Technologies under license from Multi-Format, Inc.
How to read this document
rIllustrations
fIllustrations of the camera, menu screens, and other items, may vary from the actual items.
rConventions used in this manual
fWords and phrases in [ ] brackets indicate details and content displayed in the viewnder or LCD
monitor.
fWords and phrases in < > brackets indicate design text used on this camera, such as button names.
rReference pages
fReference pages in this document are indicated by (page 00).
rTerminology
fSD memory card, SDHC memory card, and SDXC memory card are referred to as “SD memory card”.
fA memory card with the “P2” logo such as AJ-P2E064AG memory card (optional) is referred to as a “P2
memory card”.
fA memory card with the “microP2” logo such as AJ-P2M032AG memory card (optional) is referred to as a
“microP2 memory card”.
fP2 memory card and microP2 memory card are referred to only as “P2 card” unless distinguished
otherwise.
fMedia such as external hard disk drives (HDD) connected to USB are referred to as “storage devices”.
fVideo that is created during a single recording operation is referred to as a “clip”.

Contents
9
Contents
Read this rst! 2
Before using the camera 10
Description of Parts 14
Left side 14
Right side 17
Front side, rear side 19
Top side 21
Power supply 24
Charging the battery 24
Attaching and removing the battery 25
Attaching and adjusting accessories 27
Attaching the eye cup 27
Setting menu structure 28
Menu types and how to open them 28
Main menu structure 28
Updating the camera rmware 30
Specications 31
Dimensions 31
Specications 31

10
Before using the camera
Before using the camera
rWhen using this product during rain or snow or when at the beach, be careful that water
does not get inside the camera recorder.
Water causes damage to the camera recorder and memory card. (Repair may be impossible)
rKeep the camera recorder away from devices (TVs, TV games, etc.) that produce
magnetism.
fIf you use the camera recorder on or near TVs, video and sound data may be distorted by
electromagnetic waves.
fStrong magnetic elds produced by speakers and large motors may cause damage to recorded contents
and may distort images.
fElectromagnetic waves emitted by microcomputers may have a harmful effect on the camera recorder
and may corrupt video and sound data.
fThe camera recorder may not operate properly if it receives harmful effects from devices that produce
magnetism. If this happens, turn off the camera recorder and either remove the battery or unplug the AC
adaptor from the power outlet. Then, replace the battery or reconnect the AC adaptor. After that, turn on
the camera recorder.
rDo not use the camera recorder near radio transmitters or high-voltage devices.
If you use the camera recorder near radio transmitters or high-voltage devices, the recorded video and
sound data may suffer harmful effects.
rWhen using the camera recorder at the beach, etc., be careful that sand and dust do not
get inside the camera recorder.
Sand and dust may damage the camera recorder and memory card. (Be careful when inserting and
removing the memory card)
rBattery charger and battery
fIf the <CHARGE> lamp continues blinking even when the battery is at its optimal temperature, the
battery or battery charger may be damaged. Contact a dealer.
fIf the battery is warm, it will take longer than usual to charge.
fIf you use the battery charger near a radio, the radio sound may be distorted. Keep the battery and
battery charger at least 1 m away from radios when in use.
fNoise may be emitted when using the battery charger, but this is not a malfunction.
rWhen carrying the camera recorder, be careful not to drop it.
fStrong shocks will damage the camera recorder body and it may not operate properly.
fIf you carry the camera recorder, use a grip strap or shoulder strap and handle it carefully.
rDo not apply insecticide or volatile materials to the camera recorder.
fIf insecticide or volatile materials come into contact with the camera recorder, the camera recorder body
may warp and the paint may come off.
fDo not allow the camera recorder to remain in contact with rubber or vinyl objects for a long period of
time.

Before using the camera
11
rAfter using the camera recorder, either remove the battery or disconnect the AC cable
from the power outlet.
rBattery characteristics
The battery is a rechargeable lithium-ion battery. It produces electrical energy via an internal chemical
reaction. This chemical reaction is easily inuenced by the surrounding temperature and humidity, so the
effective usage time of the battery is reduced when the surrounding temperature is hot or cold. When used
in extremely low temperature environments, the effective usage time is approximately ve minutes.
When the battery is in an extremely hot environment, its protective function will operate and the camera
recorder cannot be used temporarily.
rAfter using the camera recorder, be sure to remove the battery.
Be sure to remove the battery from the camera recorder. (If the battery is left in the camera recorder, it will
continue to consume a small amount of electric current even when the power is turned off)
If the battery is left inside the camera recorder for a long time, it will over discharge and may become
unusable even if it is recharged.
Do not remove the battery when the power is turned on.
Turn off the power and remove the battery after the operation lamp goes completely out.
rTake proper care of the battery terminal.
Do not allow dust or foreign objects on the battery terminal.
Also, if you drop the battery by mistake, make sure that the battery body and the terminal are not warped.
Inserting a deformed battery into the camera recorder or attaching it to the battery charger may cause
damages on the camera recorder or battery charger.
rCautions when throwing memory cards away or transferring them to others
Formatting memory cards or deleting data using the functions of the camera or a computer will merely
change the le management information: it will not completely erase the data on the cards. When throwing
these cards away or transferring them to others, either physically destroy them or use a data deletion
program for computers (commercially available) to completely erase the data. Users are responsible for
managing the data stored in their memory cards.
rLCD monitor and viewnder
fIf the same image or letters are allowed to be displayed on the LCD monitor for a long time, the image
may be burned into the screen. It will return to normal after leaving the camera recorder turned off for
several hours.
fCondensation sometimes forms on the LCD panel of the LCD monitor in locations subject to extreme
temperature differences. If this happens, wipe with a soft, dry cloth.
fIf the camera recorder is very cold, the LCD monitor will be slightly darker than normal immediately
after the power is turned on. The screen will return to its regular brightness when the temperature inside
increases.
fSince the viewnder of the camera uses organic EL, if the same image or letters are allowed to be
displayed for a long time, the image may be burned into the screen. There is no problem with the
recorded images.
Switch the screen by turning off the screen or by using the eye sensor, etc.
fThe LCD monitor and viewnder (organic EL) are highly-precisely managed so that at least 99.99% of
the dots are effective pixels and 0.01% or less are invalid pixels and always lit. This is not a malfunction
and it has no effect whatsoever on the recorded images.
rDo not point the eye piece of the lens and viewnder at the sun.
Doing so might damage the components inside.

12
Before using the camera
rProtective cap for the terminal
Place a protective cap on connection terminals not being used.
rGPS
GPS (Global Position System) satellite is managed by the United States Department of State and its
precision is sometimes intentionally changed.
Position it in a location where there is a good view of the sky and there is no inuence of obstacles such as
roofs and trees, etc.
Depending upon the surrounding environment and the time, it may take a long time to position and errors
may be larger.
rCaution regarding laser beams
The MOS sensor may be damaged if the MOS sensor is subjected to light from a laser beam.
Take sufcient care to prevent laser beams from striking the lens when shooting in an environment where
laser devices are used.
rNote the following points.
fIf you prepare to record important images, always shoot some advance test footage to verify that both
pictures and sound are being recorded normally.
fShould video or audio recording fail due to a malfunction of the camera or the P2 cards used, we will not
assume liability for such failure.
fSet up or check the calendar and time zone before recording. These settings have an effect on the
management and playback order for recorded contents.
rSoftware information about this product
1 This product includes software licensed under GNU General Public License (GPL) and GNU
Lesser General Public License (LGPL), and customers are hereby notied that they have rights
to obtain, re-engineer, and redistribute the source code of these software.
2 This product includes software licensed under MIT-License.
3 This product includes software developed by the OpenSSL Project for use in the OpenSSL
Toolkit (http://www.openssl.org/).
4 This product includes software licensed under OpenBSD License.
5 This product includes PHP, freely available from <http://www.php.net/>.
6 This software is based in part on the work of the Independent JPEG Group.
For details on these descriptions (originally provided in English) and how to obtain the source code, visit
the following website.
http://pro-av.panasonic.net/
We do not accept inquiries about the details of the source code obtained by the customer.
rPrecautions when installing USB drivers
For the latest information on the driver, visit the following website.

Before using the camera
13
http://pro-av.panasonic.net/
fInstall the required driver into your computer from the website.
fFor installation procedure of the driver, refer to the installation manual on the website.

14
Description of Parts
Description of Parts
Left side
1
2
3
4
5
6 8
7 9 11 13 14
20 21
15
2524
26 27
28
29
30
31
22
23
10 12
16 18
17 19
1 Focus ring
Focus manually when the <FOCUS> switch is set to <M>.
2 Zoom ring
Adjust the zoom manually when the <ZOOM> switch is set to <MANUAL>.
3 Lens cover switching lever
Open/close the lens cover.
4 Iris ring
Adjust the lens iris manually when the manual iris is set with the <IRIS> button.
5 <ZOOM> switch
Select the operation of the zoom.
<SERVO>: You can use the motor-driven zoom using the zoom lever.
<MANUAL>: You can operate the zoom ring manually to adjust the angle of view.
6 <DISP/MODE CHK> switch
This is the spring switch to check the status of the shooting, etc.
fPush this switch towards the <OFF> side to clear all displays except the display of the operation
status, frame display such as an area, counter, marker, and safety zone.
fPush this switch towards the <CHK> side to display all information such as setting status of the
functions for the shooting, the list of functions assigned to the USER buttons on the LCD monitor
during shooting stand-by or shooting. Each time the switch is pushed towards the <CHK> side, the
display of the status switches in turn.

Description of Parts
15
7 <GAIN> switch
Switch the brightness of the screen according to the lighting conditions under which you are shooting.
8 <F.AUDIO LEVEL> dial
In the following conditions, the recording levels for the audio channels 1 to 4 can be adjusted.
fWhen the <CH1>/<CH2> switch is set to <MANU>
fWhen [AUTO LEVEL CH3]/[AUTO LEVEL CH4] is set to [OFF] in the main menu →[AUDIO SETUP]
→[RECORDING CH SETTING]
Assignment of audio channels 1 to 4 can be performed in the main menu →[AUDIO SETUP] →
[RECORDING CH SETTING] →[FRONT VR SELECT].
9 <WHITE BAL> switch
Select the method for adjustment of the white balance.
<PRST>: Set the white balance to the preset value. Each time the <AWB> button is pressed, [3200K],
[5600K], and [VAR] are toggled.
<A>/<B>: Select when using the stored value of the adjustment of the white balance.
10 <MENU> button
Press this button to display [USER MENU]. Press this button for 3 seconds or more to display the main
menu. Press it again to return to the original image.
11 <SEL/PUSH SET> dial button
Move, select, and set the items in the setting menu while the setting menu is displayed.
Set the preset values of the shutter, synchro scan, variable frame rate value, and white balance.
12 <MODE/MENU CANCEL> button
fWhen the setting menu is not displayed, each press of the button switches modes to change the
variable value of shutter speed, variable frame rate, and white balance.
fWhen the setting menu is displayed, setting of the menu items is canceled and the previous screen is
displayed.
13 <AUTO/MANUAL> switch
Select the method to adjust the focus, gain, iris, white balance, and shutter speed at shooting. You can
set the function to assign to <AUTO> in the main menu →[AUTO SW].
<AUTO>: Adjust automatically. (Auto mode)
<MANUAL>: Adjust manually. (Manual mode)
14 <SLOT SEL> button
Select the microP2 memory card slot for the target of recording.
This button can be used as the USER button (USER7).
15 Diopter adjustment lever
Adjust the diopter scale so that the viewnder screen can be viewed clearly.
16 <INPUT 1>/<INPUT 2> switch
Switch audio input signals connected to the <AUDIO INPUT 1>/<AUDIO INPUT 2> terminal.
<LINE>: Select when audio equipment is connected by the line input.
<MIC>: Select when the external microphone is connected.
<+48V>: Select when the external microphone is connected and the microphone needs power supply.
17 <CH1 SELECT>/<CH2 SELECT> switch
Select the audio to be recorded to audio channel 1/2.
<INT(L)>/<INT(R)>: Record left audio (right audio) of the built-in microphone.
<INPUT1>: Record input signals from the <AUDIO INPUT 1> terminal.
<INPUT2>: Record input signals from the <AUDIO INPUT 2> terminal.
18 <CH1>/<CH2> switch
Select the method to adjust the input level of audio channel 1/2.
<AUTO>: Adjust automatically.
<MANU>: Adjust using the <AUDIO LEVEL CH1>/<AUDIO LEVEL CH2> dial.

16
Description of Parts
19 <AUDIO LEVEL CH1>/<AUDIO LEVEL CH2> dial
Adjust the recording level of audio channel 1/2.
20 Internal speaker
Output audio during playback.
When connecting the headphones to the headphones terminal, audio from the speaker turns off
automatically.
21 HANDLE ZOOM switch
Select the operation of the zoom lever (handle side).
<FIX>: Zoom in/out with the speed set in the main menu →[SW MODE] → [H.ZOOM SPEED].
<VAR>: Zoom speed changes depending on how strong the lever is pushed. (When pushed gently, the
speed becomes slower, and when pushed strongly, it becomes faster.)
<OFF>: The zoom lever does not work.
22 <ND FILTER> switch
Select the lter to suit the illumination of the subject.
<1/64>: Reduce the amount of light entering the MOS sensor to 1/64.
<1/16>: Reduce the amount of light entering the MOS sensor to 1/16.
<1/4>: Reduce the amount of light entering the MOS sensor to 1/4.
<OFF>: Does not use the ND lter.
23 <IRIS> button
Select the method for adjustment of the lens iris.
24 <FOCUS ASSIST> button
Switch on/off the focus assist function.
This button can be used as the USER button (USER1).
25 <MACRO> button
Switch on/off the macro function of the focus.
This button can be used as the USER button (USER2).
26 <FOCUS> switch
Select the focus function.
<A>: Changes to the auto focus mode. Adjust the focus automatically.
<M>: Changes to the manual focus mode. Control the focus ring manually to adjust the focus.
<c>: Changes to the manual focus mode after the focus distance is set to innity.
This is the spring switch. Even when the <FOCUS> switch is pushed towards the <c> side, the switch
returns to the <M> position.
27 <PUSH AUTO> button
When the button is pressed in manual focus mode, focus is adjusted automatically while it is pressed.
28 <OIS> button
Switch on/off the image stabilization function.
This button can be used as the USER button (USER3).
29 <ZEBRA> button
Select the display of either zebra of marker.
This button can be used as the USER button (USER4).
30 <WFM> button
Select whether to display the waveform monitor on the LCD monitor.
This button can be used as the USER button (USER5).
31 <A.IRIS.LEVEL> button
Switch on/off the auto iris function.
Set the target value of the auto iris level in the main menu →[SCENE FILE] →[A.IRIS LEVEL
EFFECT].
This button can be used as the USER button (USER6).

Description of Parts
17
Right side
187 2 3 54 6
16
9
10
11
12 15
13 17
18
14
1 Eye cup
2 Eye piece
3 Busy (active status indication) lamp
Indicate the active status of the SD memory card, and is illuminated when the card is active.
4 SD memory card slot
This is the insertion slot for the SD memory card (optional). Use the SD memory card for recording/
opening the setting menu of the camera, or uploading metadata or proxy recording, etc.
@@NOTE
tCautions when using SD memory cards
- On the camera, use SD memory cards that conform to the SD standard, SDHC standard, or the
SDXC standard. When performing proxy recording, use SDHC memory cards, SDXC memory
cards, or SD memory cards with the class description of class2 or higher.
- MMC (Multi Media Card) cannot be used. (Bear in mind that taking pictures may no longer be
possible if you use them.)
- When using miniSD/microSD cards with the camera, always install the adaptor specially designed
for miniSD/microSD cards. (The camera will not work properly if only the miniSD/microSD adaptor is
installed. Make sure that the card has been inserted into the adaptor before use.)
- Use of Panasonic SD memory cards and miniSD/microSD cards is recommended. Be sure to
format cards on the camera before use.
- Refer to our support desk at the following website for the latest information not included in these
operating instructions.
http://pro-av.panasonic.net/
- SDHC memory cards are a standard that was established in 2006 by the SD Association for large-
capacity memory cards that exceed 2 GB.

18
Description of Parts
- SDXC memory cards are a standard that was established in 2009 by the SD Association for large-
capacity memory cards that exceed 32 GB.
5 Recording button (grip side)
Press this button to start recording. Press it again to stop recording.
Used for direct shooting in thumbnail mode.
6 Power switch
Switch on/off the power.
7 Microphone cable clamp
Used for securing the microphone cable.
8 Pin holder
Attach the zoom ring pin which is removed from the camera.
9 Headphones terminal
This is the connecting terminal of headphones for audio monitor.
10 <AUDIO INPUT 2> terminal (XLR, 3-pin)
Connect the audio equipment or the microphone.
11 <SDI OUT> terminal
This is the output terminal for HD/SD SDI signals.
12 <TC IN/OUT> terminal
This is the input/output terminal for time code.
Use the <IN/OUT> switch to select the input or output.
13 <GENLOCK IN/VIDEO OUT> terminal
This is the input terminal for reference signals when setting the genlock to the camera section. This is
the output terminal of the video for monitor.
Use the <IN/OUT> switch to switch the input or output.
14 <IN/OUT> switch
Switch the input and output of the <TC IN/OUT> terminal and <GENLOCK IN/VIDEO OUT> terminal.
15 <CAM REMOTE> terminal
Connect the remote control (optional) to control some functions remotely.
<FOCUS IRIS>: (3.5 mm mini jack) Control the focus operation and iris operation remotely.
<ZOOM S/S>: (2.5 mm mini jack) Control the zoom operation and start/stop operation of recording
remotely.
16 Tripod holes
Attach the tripod. (bottom)
fMounting hole size
-1/4-20 UNC (screw length 5.5 mm or shorter)
-3/8-16 UNC (screw length 5.5 mm or shorter)
17 <OPEN> button
Use this button when opening the cover of the <USB2.0 HOST> terminal at the bottom of the button.
18 <USB2.0 HOST> terminal (sub-host)
This is the terminal for the wireless LAN. Mount the wireless module AJ-WM30 (optional).

Description of Parts
19
Front side, rear side
1 1 76 2 3
5
8
411109
12
13
14
15
16
17
19
20
21
22
23
18
1 Built-in microphone
This is the built-in stereo microphone.
2 Light sensor
Detects indoor and outdoor light.
3 Front tally lamp
Lights during shooting. This lamp will blink when the battery level becomes low.
4 Recording button (front side)
Press this button to start recording. Press it again to stop recording.
The operation of this button can be forbidden by the main menu →[SW MODE] →[FRONT REC].
5 <AWB> button
Press this button to adjust the white balance. Press it for two seconds or more to adjust the white
balance and then black balance.
6 Eye sensor
Bring your eyes closer to display the screen on the viewnder.
@@NOTE
tThe eye sensor may not work properly depending on the shape of glasses in use, how you hold the
camera, or by hitting the strong light around the eye piece.
tThe eye sensor does not work during video playback.
7 Viewnder
8 <AUDIO INPUT 1> terminal (XLR, 3-pin)
Connect the audio equipment or the microphone.
9 Rear tally lamp
Light during shooting. This lamp will blink when the battery level becomes low.
10 Battery attachment

20
Description of Parts
11 Battery release button
Remove the battery.
12 microP2 memory card 1 access LED
Indicate the access status of recording and playback of the card inserted in the microP2 memory card
slot 1.
13 microP2 memory card slot 1
14 microP2 memory card 2 access LED
Indicate the access status of recording and playback of the card inserted in the microP2 memory card
slot 2.
15 microP2 memory card slot 2
16 P2 memory card slot
17 P2 memory card access LED
Indicate the access status of recording and playback of the card inserted in the P2 memory card slot.
18 <AUDIO OUT> terminal
Output audio signals recorded to audio channel 1/2.
19 <USB3.0 HOST> terminal (host)
Connect external hard disk drive, etc.
20 <USB2.0 DEVICE> terminal (device)
Connect to a computer with the USB 2.0 cable to transfer data.
21 <HDMI OUT> (monitor output) terminal
This is the output terminal of the video for monitor.
22 <LAN> terminal
Connect the LAN cable.
23 <DC IN 12V> terminal
This is the input terminal for the external power supply. Connect the supplied AC adaptor.