Panasonic SDR-S26 User manual

until
2009/1/23
Operating Instructions
SD Video Camera
Model No. SDR-S26
Before connecting, operating or adjusting this product, please read the instructions completely.
LSQT1490 B
PU
SDR-S26PU-LSQT1490_mst.book 1 ページ ２００９年１月１９日 月曜日 午後４時２７分

2
LSQT1490
Information for Your Safety
Use only the recommended accessories.
≥Do not use any other AV cables and USB
cables except the supplied one.
≥When you use the cable which are sold
separately, please make sure to use the one
whose length is less than 3 meters.
≥Keep the Memory Card out of reach of children
to prevent swallowing.
-If you see this symbol-
WARNING:
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR PRODUCT
DAMAGE,
≥DO NOT EXPOSE THIS APPARATUS TO
RAIN, MOISTURE, DRIPPING OR
SPLASHING AND THAT NO OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES,
SHALL BE PLACED ON THE
APPARATUS.
≥USE ONLY THE RECOMMENDED
ACCESSORIES.
≥DO NOT REMOVE THE COVER (OR
BACK); THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION!
≥DO NOT INSTALL OR PLACE THIS UNIT
IN A BOOKCASE, BUILT-IN CABINET OR
IN ANOTHER CONFINED SPACE.
ENSURE THE UNIT IS WELL
VENTILATED. TO PREVENT RISK OF
ELECTRIC SHOCK OR FIRE HAZARD
DUE TO OVERHEATING, ENSURE THAT
CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE
VENTILATION VENTS.
≥DO NOT OBSTRUCT THE UNIT’S
VENTILATION OPENINGS WITH
NEWSPAPERS, TABLECLOTHS,
CURTAINS, AND SIMILAR ITEMS.
≥DO NOT PLACE SOURCES OF NAKED
FLAMES, SUCH AS LIGHTED CANDLES,
ON THE UNIT.
≥DISPOSE OF BATTERIES IN AN
ENVIRONMENTALLY FRIENDLY
MANNER.
The socket outlet shall be installed near the
equipment and easily accessible.
The mains plug of the power supply cord shall
remain readily operable.
To completely disconnect this apparatus from
the AC Mains, disconnect the power supply
cord plug from AC receptacle.
Camera:
Product Identification Marking is located in the
battery compartment of the unit.
AC adaptor:
Product Identification Marking is located on
the bottom of unit.
Information on Disposal in other Countries
outside the European Union
This symbol is only valid in the
European Union.
If you wish to discard this
product, please contact your
local authorities or dealer and
ask for the correct method of
disposal.
SDR-S26PU-LSQT1490_mst.book 2 ページ ２００９年１月１９日 月曜日 午後４時２７分

3
LSQT1490
∫Indemnity concerning recording
content
The manufacturer shall in no event be liable for
the loss of recordings due to malfunction or
defect of this unit, its accessories or recordable
media.
∫Carefully observe copyright laws
Recording of pre-recorded tapes or discs or
other published or broadcast material for
purposes other than your own private use
may infringe copyright laws. Even for the
purpose of private use, recording of certain
material may be restricted.
∫Cards that you can use with this
unit
SD Memory Card and SDHC Memory Card
≥4 GB or more Memory Cards that do not have
the SDHC logo are not based on SD Memory
Card Specifications.
≥Refer to page 15 for more details on SD cards.
∫For the purposes of these
operating instructions
≥SD Memory Card and SDHC Memory Card are
referred to as the “SD card”.
≥Pages for reference are indicated by an arrow,
for example: l00
∫Licenses
≥SDHC Logo is a trademark.
≥U.S. Patent Nos. 6,836,549; 6,381,747;
7,050,698; 6,516,132; and 5,583,936.
This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Macrovision, and is intended for
home and other limited viewing uses only
unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
≥Manufactured under license from Dolby
Laboratories.
Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
≥Microsoft®, Windows®, Windows Vista®,
DirectDraw®, DirectSound® and DirectX®are
either registered trademarks or trademarks of
the Microsoft Corporation in the United States
and/or other countries.
≥Microsoft product screen shot(s) reprinted with
permission from Microsoft Corporation.
≥IBM, PC/AT and PowerPC are registered
trademarks of International Business Machines
Corporation of the U.S.
≥Intel®, Core™, Pentium®and Celeron® are the
registered trademarks or trademarks of the
Intel Corporation in the United States and other
countries.
≥YouTube and the YouTube logo are the
registered trademarks or trademarks of
YouTube LLC.
≥Macintosh and Mac OS are either registered
trademarks or trademarks of Apple Inc. in the
United States and/or other countries.
≥Other names of systems and products
mentioned in these instructions are usually the
registered trademarks or trademarks of the
manufacturers who developed the system or
product concerned.
SDR-S26PU-LSQT1490_mst.book 3 ページ ２００９年１月１９日 月曜日 午後４時２７分

4
LSQT1490
Information for Your Safety ...........................2
Accessories.....................................................6
Preparation
Before using
[1] Parts identification and handling....... 7
[2] Power supply ..................................... 10
Inserting the battery............................. 10
Charging the battery ............................ 11
Charging time and recordable time ..... 13
[3] About SD cards.................................. 14
About SD cards ................................... 14
Access lamp ........................................ 16
[4] Inserting/removing an SD card ........ 17
Setup
[1] Turning the unit on/off
Selecting a mode ............................... 18
[2] Using the menu screen ..................... 19
Language selection ............................. 20
Menu list .............................................. 20
[3] Setting date and time ........................ 22
World time setting (Displaying the time
of the travel destination) ...................... 23
[4] Adjusting LCD monitor ..................... 24
Recording
Recording (Basic)
[1] Before recording................................ 25
Intelligent auto mode ........................... 25
[2] Recording motion pictures............... 27
Record motion picture to be uploaded
to YouTube .......................................... 28
Recording modes and recordable
time...................................................... 29
[3] Recording still pictures..................... 30
Number of pixels.................................. 31
[4] Recording functions.......................... 32
Zoom in/out function ............................ 32
Recording yourself............................... 33
Quick start ........................................... 33
Optical image stabilizer function.......... 34
Recording (Advanced)
[1] Recording functions of operation
icons................................................... 35
Operation icons................................... 36
Backlight compensation/Fade/Help
mode/MagicPix/Soft skin mode/
PRE-REC/Face detection/Self-timer
[2] Recording functions of menus ........ 41
Menus ................................................. 41
Aspect ratio/Wind noise reduction/
Guideline/Auto slow shutter
[3] Manual recording functions ............. 43
Scene mode........................................ 44
Manual focus adjustment .................... 44
White balance ..................................... 45
Manual shutter speed/aperture
adjustment........................................... 46
Playback
Playback
[1] Motion picture playback ................... 47
[2] Still picture playback ........................ 50
Editing
[1] Deleting scenes/files......................... 52
Deleting scenes/files one at a time ..... 52
Deleting multiple scenes/files.............. 52
Deleting the copied scenes
collectively........................................... 53
[2] Editing scenes................................... 54
[3] Editing still pictures.......................... 55
SD card management
[1] Formatting an SD card...................... 57
With other products
[1] Playback on TV.................................. 58
[2] With a DVD burner ............................ 60
Connecting this unit to the DVD
burner.................................................. 61
DVD COPY function............................ 62
FAVORITE SCENES function ............. 63
Notes for copying data to discs using
the DVD burner ................................... 65
Playing back a disc inserted in
the DVD burner ................................... 66
Contents
SDR-S26PU-LSQT1490_mst.book 4 ページ ２００９年１月１９日 月曜日 午後４時２７分

5
LSQT1490
PreparationRecordingPlaybackWith a PCOthers
[3] With other video devices .................. 67
Recording (dubbing) images onto other
video devices....................................... 67
[4] With a printer (PictBridge) ................ 68
With a PC
Before using
[1] What you can do with a PC............... 70
[2] Operating environment ..................... 71
End User License Agreement.............. 73
Setup
[1] Installation.......................................... 74
Installing VideoCam Suite ................... 74
Uninstalling the software ..................... 75
[2] Connection and recognition............. 76
About the PC display ........................... 76
To disconnect USB cable safely .......... 77
Using software
[1] Using VideoCam Suite ...................... 78
Reading the operating instructions of
the software ......................................... 78
Upload to YouTube .............................. 79
Using a Macintosh
[1] If using a Macintosh .......................... 80
Others
Indications
[1] Indications.......................................... 81
[2] Messages ........................................... 84
Helpful hints
[1] Functions that cannot be used
simultaneously .................................. 86
[2] Troubleshooting ................................ 87
Cautions for use ...........................................92
Explanation of terms ....................................95
Specifications ...............................................97
Number of recordable pictures .......... 100
SDR-S26PU-LSQT1490_mst.book 5 ページ ２００９年１月１９日 月曜日 午後４時２７分

6
LSQT1490
Accessories
Check the accessories before using this unit.
Battery pack
VW-VBJ10
AV cable
K2KC4CB00022
≥The battery is not charged. Be sure to charge the
battery before using this unit. (l11)
AC adaptor
VSK0695
USB cable
K1HA05AD0006
AC cable
K2CA2CA00029 or
K2CA2CA00025
CD-ROM
SDR-S26PU-LSQT1490_mst.book 6 ページ ２００９年１月１９日 月曜日 午後４時２７分

7
LSQT1490
Preparation
Before using 1Parts identification and
handling
1 LCD monitor open
2 Joystick
3 LCD monitor
4 Web mode button [WEB MODE] (l28)
5 When recording: Zoom lever [W/T] (l32)
When playing back: Volume lever
[sVOLr] (l48)
6 Intelligent auto button [iA] (l25)
7 Menu button [MENU] (l19)
8 Speaker
9 Delete button [ ] (l52)
10 Manual button [MANUAL AF/MF] (l43)
11 Optical image stabilizer button
[ , O.I.S.] (l34)
12 SD Card access lamp [ACCESS]
(l16)
13 SD Card slot cover [SD CARD] (l17)
14 SD card slot (l17)
8
6
791011 12 13
12 3 54
14
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the LCD monitor screen.
However, this is not a malfunction and
does not affect the recorded picture.
LCD monitor
Pull the LCD monitor out in the direction of
the arrow with your fingers.
≥It can open up to 90o.
≥It can rotate up to 180oAtowards the lens
or 90o B towards the opposite direction.
≥The brightness and color level of the LCD
monitor can be adjusted. (l24)

SDR-S26PU-LSQT1490_mst.book 7 ページ ２００９年１月１９日 月曜日 午後４時２７分

8
LSQT1490
15 Open/close switch for the lens cover
16 Lens
17 Grip belt
18 Microphone (built-in, stereo)
Joystick
Use the joystick to select the recording
functions and playback operations, and to
operate the menu screen.
Move the joystick up, down, left, or right to
select a setting or scene and then press
the joystick to set it.
1Select by moving up, down, left or right.
2Set by pressing the center.
≥Menu screen operations (l19)
≥To select the recording functions (l35)
≥To adjust manually (l43)
≥Playback operations (l47, 50)

18
16
17
15
Lens cover
For the lens protection, be sure to close the
lens cover when not in use.
Slide open/close switch for the lens cover.
Grip belt
Adjust the belt length and the pad position.
1Flip the belt.
2Adjust the length.
3Replace the belt.


SDR-S26PU-LSQT1490_mst.book 8 ページ ２００９年１月１９日 月曜日 午後４時２７分

9
LSQT1490
19 Status indicator (l11, 18)
20 Mode dial (l18)
21 Recording start/stop button (l27, 30)
22 Terminal cover
23 Audio-video output terminal [A/V]
(l58, 67)
24 DC input terminal [DC IN] (l11)
≥Do not use any other AC adaptors except the
supplied one.
25 USB terminal [ ] (l61, 68, 76)
26 Tripod receptacle
27 Battery cover (l10)
28 Battery cover release button [PUSH/
SLIDE OPEN] (l10)
24 2523
20
19
22
21
Tripod receptacle
This is a hole for attaching the unit to the
optional tripod.
≥When the tripod is used, the battery cover
cannot be opened. Insert the battery before
attaching this unit to the tripod. (l10)
27
26
28
SDR-S26PU-LSQT1490_mst.book 9 ページ ２００９年１月１９日 月曜日 午後４時２７分

10
LSQT1490
Preparation
Before using 2Power supply
∫About batteries that you can use with this unit
The battery that can be used with this unit is supplied battery/VW-VBJ10.
¬Rotate the mode dial to select OFF.
Insert the battery until it clicks paying attention to the direction of the
battery.
≥Be sure to set the mode dial to OFF and check that the status indicator is off before removing the
battery.
It has been found that counterfeit battery packs which look very similar to the genuine
product are made available to purchase in some markets. Some of these battery packs are
not adequately protected with internal protection to meet the requirements of appropriate
safety standards. There is a possibility that these battery packs may lead to fire or explosion.
Please be advised that we are not liable for any accident or failure occurring as a result of use
of a counterfeit battery pack. To ensure that safe products are used we would recommend
that a genuine Panasonic battery pack is used.
Inserting the battery


Removing the battery
Open the battery cover, then
remove the battery.
ABattery cover release button [PUSH/SLIDE OPEN]
1While pressing the battery cover release button, slide
and open the battery cover
2Close and slide the battery cover
SDR-S26PU-LSQT1490_mst.book 10 ページ ２００９年１月１９日 月曜日 午後４時２７分

11
LSQT1490
The unit is in the standby condition when the AC adaptor is connected. The primary circuit is always
“live” as long as the AC adaptor is connected to an electrical outlet.
When this unit is purchased, the battery is not charged. Charge the battery before using this unit.
¬Rotate the mode dial to select OFF.
The battery will not be charged if the power is turned on.
1Open the LCD monitor and then open the terminal cover.
2Connect the AC cable to the AC adaptor and the AC outlet.
3Connect the AC adaptor to this unit’s DC input terminal.
≥Do not use the AC cable with any other equipment as it is designed only for this unit. Also, do not use
the AC cable from other equipment with this unit.
≥We recommend using Panasonic batteries (VW-VBJ10).
≥If you use other batteries, we cannot guarantee the quality of this product.
≥Do not heat or expose to flame.
≥Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period of time with
doors and windows closed.
Charging the battery




Status indicator A
Flashes red at intervals of about 1
second:
Charging (l13, Charging time)
Goes off:
Charging completed
Flashes rapidly or slowly:
Charging errors have occurred (l12)
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the
manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
Warning
Risk of fire, explosion and burns. Do not
disassemble, heat above 60 xC (140xF) or
incinerate.
SDR-S26PU-LSQT1490_mst.book 11 ページ ２００９年１月１９日 月曜日 午後４時２７分

12
LSQT1490
∫About charging errors
If the status indicator does the following:
Does not flash:
Remove and reinsert the battery, and disconnect
and reconnect the AC adaptor.
Flashes rapidly at approx. 0.25 seconds
intervals:
The battery cannot be charged. Try doing the
following.
≥Remove and reinsert the battery, and try
recharging the battery.
≥The battery temperature or surrounding
temperature is too high/low, therefore wait until
the unit and the battery are at suitable
temperatures and try recharging the battery.
Flashes slowly at approx. 3 seconds
intervals:
Charging requires time for the following reasons:
≥The battery has been excessively discharged.
≥The battery temperature or ambient
temperature is too high/low.
∫Connecting to the AC outlet
If you turn on this unit while charging the battery
using the AC adaptor, you can use the power
supplied from the AC outlet to power the unit for
use. (While it is in use, the battery will not be
charged.)
If the status indicator still does not flash, contact
consumer support.
If battery charging still does not commence,
contact consumer support.
SDR-S26PU-LSQT1490_mst.book 12 ページ ２００９年１月１９日 月曜日 午後４時２７分

13
LSQT1490
∫Charging time
≥Temperature: 25 oC (77 oF)/humidity: 60%
≥If the temperature is higher or lower than 25 oC (77 oF), the charging time will become longer.
∫Recordable time
≥Temperature: 25 oC (77 oF)/humidity: 60%
≥These times are approximations.
≥The actual recordable time refers to the recordable time when repeatedly starting/stopping recording,
turning the unit on/off, moving the zoom lever, etc.
≥The recordable times will vary depending on the status of use. Be aware that the operating time of the
battery will become shorter in low temperatures. We recommend charging a spare battery for use
when recording.
≥The batteries heat up after use or charging. This unit will also heat up while being used. This is not a
malfunction.
Charging time and recordable time
Battery model number Voltage/Capacity (Minimum) Charging time
Supplied battery/
VW-VBJ10 (optional) 3.6 V/940 mAh 2 h 15 min
Battery model
number
Voltage/Capacity
(Minimum)
Maximum
continuously
recordable time
Actual recordable
time
Supplied battery/
VW-VBJ10 (optional) 3.6 V/940 mAh 1 h 15 min 40 min
Battery capacity indication
≥The display changes to the following indications step-by-step as the battery capacity decreases.
####
≥If the battery discharges, then ( ) will flash.
SDR-S26PU-LSQT1490_mst.book 13 ページ ２００９年１月１９日 月曜日 午後４時２７分

14
LSQT1490
Preparation
Before using 3About SD cards
This unit can be used for recording motion pictures and still pictures to an SD card.
* Cannot be guaranteed in operation.
≥Please confirm the latest information on the following website. (This website is in English only.)
http://panasonic.jp/support/global/cs/e_cam
≥This unit supports SD Memory Cards formatted in FAT12 system and FAT16 system based on SD
Memory Card Specifications and SDHC Memory Cards formatted in FAT32 system.
≥If you wish to use Memory Cards that are 4 GB or more, only SDHC Memory Cards can be used.
≥4 GB or more Memory Cards that do not have the SDHC logo are not based on SD Memory Card
Specifications.
≥Use this unit to format SD cards. If an SD card is formatted on other products (such as a PC), the time
spent for recording may become longer and you may not be able to use the SD card. (l57)
≥We recommend that you use a Panasonic brand SD card.
≥When using an SD card on which data has been written many times, the remaining time left for
recording may be reduced.
≥When the write-protect switch Aon SD card is locked, no recording, deletion or
editing will be possible on the card.
≥Keep the Memory Card out of reach of children to prevent swallowing.
≥A MultiMediaCard cannot be used on this unit.
SD Memory Card SDHC
Memory Card
Capacity
8MB/16MB 32 MB/64 MB/
128 MB
256 MB/
512 MB/1 GB/
2GB
4GB/6GB/
8GB/12GB/
16 GB/32 GB
Functions
Recording motion pictures – ¥*¥
Recording still pictures ¥
¥: applicable –: not applicable
About SD cards
This unit is compatible with both SD Memory cards and SDHC Memory cards. You can only use
SDHC Memory cards on devices that are compatible with them. You cannot use SDHC Memory
cards on devices that are only compatible with SD Memory cards. (When using an SDHC Memory
card on another device, be sure to read the operating instructions for that device.)

SDR-S26PU-LSQT1490_mst.book 14 ページ ２００９年１月１９日 月曜日 午後４時２７分

15
LSQT1490
We recommend using SD cards conforming to Class 2 or higher of the SD Speed Class Rating or the
following SD cards made by Panasonic for motion picture recording. (If another kind of SD card is used,
the recording may suddenly stop during motion picture recording.)
≥Operation in motion picture recording is not guaranteed with the following SD cards.
jSD cards from 32 MB to 128 MB
jSD cards from 256 MB to 32 GB other than the ones mentioned above
≥Do not touch the terminals on the back of the card.
≥Do not expose the terminals of the card to water, garbage or dust.
≥Do not leave SD card in the following areas:
jIn direct sunlight.
jIn very dusty or humid areas.
jNear a heater.
jLocations susceptible to significant difference in temperature (condensation can occur).
jWhere static electricity or electromagnetic waves occur.
≥To protect SD cards, keep them in their cases when not being used.
≥Electrical noise, static electricity, or failure of this unit or the SD card may damage or erase the data
stored on the SD card. We recommend saving the SD data to a PC.
About SD cards that you can use for motion picture recording
High Speed SD
Memory Card
Class 2 SD/SDHC
Memory Card
Class 4 SD/SDHC
Memory Card
Class 6 SD/SDHC
Memory Card
256 MB RP-SDH256 RP-SDR256 – –
512 MB RP-SDK512 RP-SDR512 – –
1GB RP-SDH01G RP-SDR01G – RP-SDV01G
2GB RP-SDK02G RP-SDR02G RP-SDM02G RP-SDV02G
4GB – RP-SDR04G RP-SDM04G RP-SDV04G
6GB – – RP-SDM06G –
8GB – – – RP-SDV08G
12 GB – – RP-SDM12G –
16 GB – – – RP-SDV16G
32 GB – – – RP-SDV32G
SD card handling
SDR-S26PU-LSQT1490_mst.book 15 ページ ２００９年１月１９日 月曜日 午後４時２７分

16
LSQT1490
ASD card access lamp [ACCESS]
≥When this unit accesses the SD card, the lamp
lights up.
≥When lamp is on, do not
sOpen the SD card slot cover and remove
the SD card
sOperate the mode dial
sRemove the battery or disconnect the AC
adaptor
≥Performing the above while lamp is on may
result in damage to data/SD card or this unit.
However, the access lamp is supposed to light
up while rotating the dial to select a mode. In
this case, there is no problem.
Access lamp

SDR-S26PU-LSQT1490_mst.book 16 ページ ２００９年１月１９日 月曜日 午後４時２７分

17
LSQT1490
Preparation
Before using 4Inserting/removing an SD
card
Caution:
If the SD card is inserted or removed while the power is on, this unit may malfunction or the data
recorded on the SD card may be lost.
1Rotate the mode dial to OFF.
≥Check that the status indicator has gone off.
2Open the LCD monitor and then open the SD card slot cover.
3Insert/remove the SD card.
≥Press the SD card straight in as far as it will go.
≥Press the center of the SD card and then pull it straight out.
4Securely close the SD card slot cover.
ALabel side




SDR-S26PU-LSQT1490_mst.book 17 ページ ２００９年１月１９日 月曜日 午後４時２７分

18
LSQT1490
Preparation
Setup 1Turning the unit on/off
Selecting a mode
Rotate the mode dial to switch to recording, playback or power OFF.
While pressing the lock release
button, set the mode dial to , ,
or to turn on the power.
The status indicator lights and the power turns
on.
≥When the unit is turned on for the first time, a
message asking you to set the date and time
will appear. Select [YES] and set the date and
time. (l22)
To turn off the power
Set the mode dial to OFF.
≥The status indicator goes off and the power
turns off.
When the mode dial is set to or , the
power can be turned on and off with the LCD
monitor.
∫To turn on
Open the LCD monitor.
The status indicator lights.
∫To turn off
Close the LCD monitor.
The status indicator goes off.
≥When quick start is set to [ON], the status
indicator flashes green. To turn off the power
immediately after closing the LCD monitor, set
quick start to [OFF]. (l33)
≥Rotate the mode dial while at the same
time pressing in the lock release button
Aif changing from OFF to another
mode.
≥Align with the status indicator B.


Video recording mode (l27)
Video playback mode (l47)
Picture recording mode (l30)
Picture playback mode (l50)
OFF
How to turn the power on and off
with the LCD monitor
Set the mode dial to OFF when this unit is not
being used.
SDR-S26PU-LSQT1490_mst.book 18 ページ ２００９年１月１９日 月曜日 午後４時２７分

19
LSQT1490
Preparation
Setup 2Using the menu screen
1Press the MENU button.
The menu displayed differs depending on the
position of the mode dial.
2Select the desired top menu, then
move the joystick right or press
the joystick.
3Select the submenu item, then
move the joystick right or press
the joystick.
4Select the desired setting, then
press the joystick to enter the
selection.
To get back to the previous screen
Move the joystick left.
To exit the menu screen
Press the MENU button.
≥Do not switch the mode dial when the menu is
displayed.
≥The menu screen does not appear during
recording or playing. You cannot start other
operations while the menu screen is displayed.
MENU
ENTER
SDR-S26PU-LSQT1490_mst.book 19 ページ ２００９年１月１９日 月曜日 午後４時２７分

20
LSQT1490
You can select the language displayed on the
screen.
1Press the MENU button, then
select [LANGUAGE] and press
the joystick.
2Select [English] and press the
joystick.
*1 It will be displayed only in the manual mode.
*2 It is not displayed when the Intelligent auto
mode is set to on.
Part of the menu will not be used depending on
the used functions. (l86)
Motion picture recording menus
∫[BASIC]
[SCENE MODE]*1 (l44)
[REC MODE] (l29)
[ASPECT] (l41)
[CLOCK SET] (l22)
[SET WORLD TIME] (l23)
∫[ADVANCED]
[D.ZOOM] (l32)
[FACE FRAMING] (l38)
[WIND CUT]*2 (l41)
[GUIDE LINES]*2 (l41)
[ZOOM MIC] (l33)
[AUTO SLW SHTR]*2 (l41)
[FADE COLOR] (l37)
∫[SETUP]
[DISPLAY]
[DATE/TIME] (l22)
[DATE FORMAT] (l22)
[FORMAT CARD] (l57)
[QUICK START] (l33)
[ECONOMY]
[AUDIO REC] (l28)
[BEEP SOUND]
[POWER LCD] (l24)
Language selection
Menu list
≥[OFF] ≥[ON]
The screen indications are selected as shown
in the illustration below.
[OFF] [ON]

NOV.15.2009
A

0h00m00s
R 1h20m
SP
NOV.15.2009
≥[OFF] ≥[5 MINUTES]
[OFF]:
The economy function is not activated.
[5 MINUTES]:
When about 5 minutes have passed without
any operation, this unit automatically turns off
to save battery life. To use this unit, turn it on
again.
≥The economy function will not activate
when:
jconnected to AC adaptor
jusing the USB for PC, DVD burner, printer
jPRE-REC is used
≥[OFF] ≥[ON]
This allows operations such as starting and
ending recording to be signaled by a beep.
1 Beep
When you start recording
When you turn on the power
When this unit is recognized by the PC or the
printer, etc.
2 Beeps
When you pause recording
When you turn off the power
2 Beeps for 4 times
When an error occurs e.g. recording not
starting. Check the sentence displayed on the
screen. (l84)
SDR-S26PU-LSQT1490_mst.book 20 ページ ２００９年１月１９日 月曜日 午後４時２７分