Panasonic CQDP875EUC - AUTO RADIO/CD DECK User manual

Panasonic.
<CQ-DP875EUC>
Removable
Face
High-Power
CD
Player/Receiver
with
Changer
Control
Récepteur/lecteur
CD
à
puissance
élevée
avec
contrôleur
de
changeur
et
panneau
avant
amovible
<CQ-DP850/DP830EUC>
Removable
Face
High-Power
CD
Player/Receiver
Aécepteur/lecteur
CD
à
puissance
élevée
avec
panneau
avant
amovible
CQ-DP875/DP850/DP830EUC
Operating
Instructions
Manuel
d'utilisation
Please
read
these
instructions
completely
before
operating
this
unit.
ll
est
recommandé
de
lire
attentivement
ce
manuel
avant
d'utiliser
l'appareil.

Izn-rozm
Panasonic welcomes you to our ever growing family of electronic product owners. We know that this
product will bring you many hours of enjoyment. Our reputation is built on precise electronic and
mechanical engineering , manufactured with carefully selected components and assembled by people
who take pride in their work. Once you discover the quality, reliability, and value we have built into this
product, you too will be proud to be a member of our family.
(1 Use This Equipment Safely
When Driving
Keep the volume level low enough to be aware of road and traffic conditions.
When Car Washing
Do not expose the equipment, including the speakers and CDs, to water or excessive moisture. This
could cause electrical shorts, fire, or other damage.
When Parked
Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a
chance to cool down before switching the unit on.
Use the Proper Power Supply
This equipment is designed to operate off a 12 volt, negative ground battery system (the normal system in
a North American car.)
Protect the Compact Disc Mechanism
Avoid insertion any foreign matters to the slot of the compact disc.
Failure to observe this may cause malfunction due to precise mechanism of this unit.
Use Authorized Servicenters
Do not attempt to disassemble or adjust this precision equipment. Please refer to the Servicenter list
included with this product for service assistance.
Note:
This operating instruction manual is for 3 models CQ-DP875EUC, DP850EUC and CQ-DP830EUC. AI
illustrations throughout this manual represent model CQ-DP875EUC unless otherwise specified. The
following table describes the differences between 3 models.
40W X 4 35W X 4
2 pre (Lead type) | 2 pre (Lead type) 1 pre (Fix)
Programmed Sound Memory
Find the model number and serial number on either the back or bottom of the unit. Please record them in
the space below and retain this booklet as a permanent record of your purchase to aid in identification in
case of theft.
MODEL NUMBER CQ-DP875/850/830EUC SERIAL NUMBER
DATE PURCHASED_______ FROM
CQ-DP875/850/830EUC

Contents
Use This Equipment Safely SiG Seneds avcebendagsavacesaudcessesaerscasevecsezeureesesesucsaeve Page 2
Laser Products-...sssssssssssssesssessssensssnssessesencnessenesessssessesesesess 6
O Power and Sound Controls ss 7
How to adjust the volume, Tone Enhancement, Attenator, balance,
and tone for best listening
O Radio Basics ----------.--...s.sssresressserisosreasssecorsesansvsacosavoevsosenerenreresesreessea 10 WO
Manual and automatic tuning, band selection, preset stations
D Compact Disc Player Basiçs..….......…......................................……… 12 S29 ) ) ))
Mode selection, play repeat, random and scan VIS
O CD Changer Basics (Only for CQ-DP875EUC) 14
Play, repeat, random and scan A
Note: TY
CD changer controls are applicable to units with optional CD charger unit
(sold separately).
O Clock Basics---...-..scmssisoissssossousssoucesssossssocsssosersaseononeosovsesesnenns 16 HN m
Initial time setting, resetting the time, selecting the clock display ‘LI LI
O Programmed Sound Memory (For CQ-DP875/DP850EUC)...---..---- 17
©) Remote Control Unit Basics (For CQ-DP875/DP850EUC) -...........- 18
Battery replacement, notes and Operating procedures.
O Installation Guide- -.-..seesssssssssessssevsossesesresovoseeresevevespestorereosereeresennsnnn 20
Step-by-step procedures, anti-theft system, electrical connections
O Trou bleshooting E E E ines 27
Error messages, troubleshooting tips,where to get service help
o Special NOTES <0-ccrccscvccvccvcescsccnrcsssccsnssascnnasnensonsssessesascseccencascnseracareenesracs 29
Notes on compact discs, a caution on new discs
Specifications... 30
3
CQ-DP875/850/830EUC

N=—PoZean
Panasonic est heureuse de vous compter parmi les utilisateurs de ses appareils électroniques.
Nous pouvons vous assurer que cet appareil vous procurera de longues heures d'agrément. Notre
réputation est fondée sur une ingénierie électronique et mécanique de haute précision laquelle préside à
la fabrication d'appareils ne comportant que des composants de choix assemblés par un personnel
soucieux de la bonne réputation acquise par la qualité de son travail. Après avoir découvert la qualité, la
valeur et la fiabilité de cet appareil, vous aussi serez fier d'être un client Panasonic.
O Précautions à prendre
Au volant
Régler le volume à un niveau qui ne risque pas de masquer les bruits ambiants.
Lavage de la voiture
Afin de prévenir tout risque de court-circuit ou d'incendie, ne pas exposer l'équipement, y compris les
haut-parleurs et les disques, à l’eau ni à une humidité excessive.
Voiture stationnée
L’habitacle d'une voiture immobile exposée au soleil toutes vitres fermées devient rapidement très chaud.
Laisser rafraîchir l'intérieur du véhicule avant d'utiliser l'appareil.
Source d'alimentation
Cet appareil est conçu pour fonctionner sur un système d'alimentation avec batterie de 12V avec négatif à
la masse (système standard sur les voitures de construction nord-américaine).
Mécanisme du lecteur audionumérique
Ne pas insérer d'objet dans le logement du disque. Autrement, le mécanisme ultra-précis du lecteur
pourrait être irrémédiablement endommagé.
Réparation
Ne pas tenter de démonter ou d'ajuster l'appareil soi-même. Confier toute réparation à un centre de
service agréé.
Remarque:
Ce manuel a été conçu pour les modèles CQ-DP875EUC, CQ-DP850EUC et CQ-DP830EUC. Toutes les
illustrations du présent manuel mettent en présence le modèle CQ-DP875EUC a moins d'indication
contraire. Le tableau ci-dessous décrit les différences entre les 3 modèles.
Modèle
Commande
[nm | o
oid
oT
Décbiemètre [Où | oi |
Voyant du système de séu | ou | où
Soris, extrémes-graves | Où | Non
Commandes du edeurctargeur amenée] Oui | Non |
DC NE ©" EE
Télécommande
Afficheur couleur LCD Vert
il est recommandé de noter, dans l'espace prévu ci-dessous, les numéros de modèle et de série inscrits
soit à l'arrière soit sous le fond de l'appareil, et de conserver ce manuel comme mémorandum de l'achat
afin de permettre l'identification de l'appareil en cas de vol.
Numéro de modèle: CQ-DP875/850/830EUC Numéro de série:
Date de l’achat: Vendeur:
CQ-DP875/850/830EUC

Table des matieres
Précautions a prendre RO RTE TES PS RTE PORT EU RETURN RP CNE IUT sagan 4
O Interrupteur et commandes de réglage de la sonorité -e 31
Comment régler le volume sonore, la fonction d'enrichissement tonal,
l'atténuateur et la commande d'équilibre pour une meilleure écoute
O Fonctionnement de la radio... 34
Syntonisation manuelle et automatique, sélection de la bande et stations rs) €
en mémoire
O Fonctionnement du lecteur audionumérique--............... 36 a.
Sélection de mode, lecture, lecture en reprise, lecture aléatoire et SON
VIY
balayage
O—PFOZrPDn
O Fonctionnement du lecteur-changeur audionumérique--------.-------- 38
(Modèle CQ-DP875EUC seulement)
Lecture, lecture en reprise, lecture aléatoire et balayage KAN
Remarque: Les commandes de changeur de disques ne s'appliquent SOS
qu'aux autoradios auxquelles un lecteur-changeur (vendu séparément)
est raccordé.
J Fonctionnement de l'horloge drsrta soie dent e est etes er rt ranVe ne rates tal idter etes nest 40 7 m
Réglage de l'heure, remise à l'heure, sélection de l'affichage de l'horloge HEI Lf
OC Mémoire des réglages GOMOTOS rrerssrsresssersnennsuarusnorennurersareeroreoranesseas 4i
(Modèles CQ-DP875/DP850EUC)
O Instructions concernant la télécommande... 42
(Modèles CQ-DP875/DP850EUC)
Remplacement de la pile, remarques et fonctionnement
O Guide d'installation- ---e-eeeeerrererressesssseeressersasnssnssssnenususnnereesosessereseeses 44
Marche à suivre, système antivol, raccordements électriques
O En cas de difficulté sise 51 P D |
Messages d'erreurs, guide de dépannage, service après-vente
O o 107 O ©
O Généralités virisicssciccrssccavccsnenscistscncsaseessccedersconsasevreseevesteeusuacedsadeons suave rinse 53
Remarques sur les disques audionumériques, précautions a prendre
Données techniques sense 54
5
CQ-DP875/850/830EUC

In-r0ozm
O Laser Products (The standard described on this page is for U.S.A. only.)
Caution:
This product utilizes a laser.
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
Laser products:
Wave length 780 nm
Laser Power No hazardous radiation is emitted with safety protection.
+ Label indications and their locations
Certification Label
Identification Label
Certification Label Identification Label
Product complies with DHHS Rules 21
FR,
Subch
in
eff
dat
Mode!
No.
ra
gla
ect
as of
date
uc
CQ-DP875EUC
Matsushita Communication Industrial Co., Ltd.
Yokohama, Japan
MANUFACTURED
Manufactured by Matsushita Communication
Industrial Co., Ltd.
Yokohama, Japan Made in Japan
CQ-DP875/850/830EUC

Power and Sound Controls
=- In-r0zm
If the car is not already running, turn the key in the ignition until the
accessory indicator lights.
Press PWR to switch on the power.
Note: When power is switched on for the first time, greeting words
display. To cancel this display, press PWR to switch power off then
power on again (For CQ-DP875/850EUC).
When a CD is inserted with all power connected, the unit power will
automatically turn on and CD loading begins and plays.
Volume
Press “VOLA” or “VOLYV’” to increase or decrease volume.
Volume Level
0 to 40
Press “VOL” or “VOLV”" for more than a half second to change
numeric levels on the display rapidly.
Attenuator
e Press ATT. Volume will decrease to about 1/10 of its previous level.
¢ Press ATT again to deactivate when listening at normal volume.
ATT
S-HDB (Super High Definition Bass)
(For CQ-DP875/850EUC)
Especially for rock music, the bass-sound will be more powerful.
e Press HDB to be able to listen to high-definition bass.
e Press HDB again to return to the normal tone.
Note: This unit is equipped with an anti-volume-blast circuit which serves as an automatic volume
level adjuster so that you will not be deafened sudden loud volume.
This system operates as follows. When PWR is switched on, the volume level is low. After that, the
volume level gradually returns to its previous level prior to switching off the unit.
7
CQ-DP875/850/830EUC

Power and Sound Controls continued
Tone Enhancement (Only for CO-DP830EUC)
Press LOUD ( © ) to enhance bass and treble tones when listening at
low or medium volume. Press LOUD ( © ) again to deactivate.
Changing Audio Modes
Press SEL to switch the audio mode in the following order.
D DBH—CFos2m
<For CQ-DP875EUC> <For CQ-DP850/830EUC>
POÈME La BASS + THERES VOLUME Le BASS -> THEBLE
t
SUB a FADER « BALANCE FADER - BALANCE
Bass and Treble
e Press SEL to select the BASS (TREBLE) mode. Press “VOL or
“VOLV” to increase or decrease the bass/treble response.
-12 to 12 -12 to 12
° Press “VOLA" or “VOLV” for more than a half second to change
4 numeric levels on the display rapidly.
Balance
e Press SEL to select the BALANCE mode. Press “VOLA” or
“VOLY” to shift the sound volume to right or left speakers.
or L 1t0 15 Balance Center
e Press “VOLA” or “VOLV” for more than a half second to change
numeric levels on the display rapidly.
Fader
+ Press SEL to select the FADER mode. Press “VOL” or “VOLV”
to shift the sound volume to the front or rear Speakers.
orR 1t0 15 Balance Center
+ Press “VOLA” or “VOLV” for more than a half second to change
numeric levels on the display rapidly.
Note: When a control mode (BAS/TRE/BAL/FAD) is selected but no operation is made within 5
seconds(2 seconds at volume mode), the display wilt return to the normal operation (Radio, CD, etc)
mode. In such a case, press SEL again to select the control mode.
8
CQ-DP875/850/830EUC

Sub-woofer Volume (Only for C0-DP875EUC)
+ Press SEL to select the Sub-woofer Volume mode.
e Press “VOLA” or “VOLV” to increase or decrease the Sub-woofer
votume level.
KA Rp LT
Gi; a rf i t-
(MUTE to 5)
Selecting Auxiliary Source
e Press AUX to select AUX Input mode. <For DP875/DP850EUC>
fy} iV
LIA
e Connect the auxiliary equipment (an optional DCC player deck or
any other appropriate equipment) to the AUX Jack.
Canceling AUX Input mode
Press AUX or MODE again while the AUX mode is operated, the
mode will return to the previous mode. Or insert a CD and the mode
will change to CD mode.
Note: The AUX mode enables setting of VOL,BAS,and
FAD, independently of other modes. (For CQ-DP875/DP850EUC)
Caution:
In order to insert the plug into the “AUX” Jack properly, make
sure to use the correct size of the stereo plug shown on the left.
A-MIN 1/2" LONG (12mm)
B-MAX 2/5" DIA. (10mm)
C-MIN 1/8" DIA. (3.5mm)
9
CQ-DP875/850/830EUC

> In-rOoOzm
10
Radio Basics
DPS7S 40W:4 CD
CQ-DP875/850/830EUC
REMOTE
}
ise ©)
©)
To change Tuner Mode
<For CQ-DP875/DP850EUC>
Tuner mode is selected if the MODE button is pressed while in either
CD Player or CD Changer Control modes (Only for CQ-DP875EUC).
<Only for CQ-DP830EUC>
You can select FM or AM directly.
Selecting a Band
<For CQ-DP875/DP850EUC> <Only for CQ-DP830EUC>
+ Press BAND to select the + Press FM to select the bands
bands in the following order. in the following order.
FM1—» FM2 —> FM3 — AM FMI ——> FM2 —~ FM3
e Press AM to select the bands.
“STEREO” indicator lights if the station is broadcasting in stereo.
Manual Tuning
Press “TUNEN” or “V TUNE” to move to a higher or lower frequency.
Seek Tuning
Press and hold “TUNE” or ““ TUNE” for more than a half second,
then release. The radio automatically stops on the next station.
MONO/LOCAL Selection
* Much interference is reduced during a weak FM stereo broadcasts.
When MONO is ON. (Only for FM mode)
e Searching stops automatically at a strong wave station only when
LOC is ON
Press MONO to switch on or off the
MONO mode as follows.
MONO OFF ~«—a MONO ON
Press LOC to switch on or off the
LOC mode as follows.
LOC OFF -#— LOC ON

(=== Preset Station Setting
Up to 24 stations can be preset in the station memory as follows;
FM FM2 FM3
Canne [ttre | Samora | Cts
Manual Station Preset
@ Press BAND to select a desired band. <For CQ-DP875/DP850EUC>
You can select FM or AM directly. <For CQ-DP830EUC>
@ Use manual or seek tuning to find a station that you want to
program into memory.
@ Press and hold one of the station selector buttons 1 through 6 until
the display blinks.
Repeat the process to set other stations for the FM1 to AM bands.
Note: You can change the memory setting by repeating the
above procedure.
Tuning in a Preset Station
Press any of the buttons 1 through 6 to tune in the station preset by
the above steps @ to @.
Auto Station Preset
Select a band and press and hold APM (AUTO PRESET) for more
than 2 seconds. (Only for CQ-DP875/DP850EUC)
Select a band and press AeP. (Only for CQ-DP830EUC)
+ The 6 strongest available stations will be automatically set in
memory preset buttons 1 through 6.
+ Once set, the preset stations are sequentially scanned for 5
seconds.
¢ Press the appropriate preset button for the station you want to
hear.
Press and Hold
ECEIVER WITH CHANGER CONTROL Q
Caution: For safety reasons, do not attempt to program while driving.
11
CQ-DP875/850/830EUC

12
Compact
Disc
Player
Basics
CQ-DP875/850/830EUC
Mode Selection
While
the
disc
is
inserted,
press
MODE
to
switch
the
operation
mode
in the following order.
<For
CQ-DP875EUC>
Tuner
—»
CD
Player
——
CD
Changer
Control
4
|
<For CQ-DP850EUC>
Tuner «—— CD Player
<For CQ-DP830EUC>
You
can
select
CD
play
(press
CD)
directly.
To
start
the
CD
Player
Insert
the
disc
(label
side
up)
and
playback
starts
automatically.
Li L UH at
“CD
LOAD”
will
be
displayed
until
the
disc
is
loaded.
Play
starts
from
first
track.
( DISC,
Note:
While
the
disc
is
inserted,
“@a
”
(DP875/DP850EUC)
or
“DISC”
(DP830EUC)
indicator
will
light.
If
you
press
“MODE”
after
the
disc
is
ejected,
the
disc
will
be
re-inserted.
Stopping
and
Ejecting
a
Disc
Press
“A
”
to
stop
CD
play,
and
the
disc
will
quietly
eject
from
the
CD
slot.
(During
disc
ejection,
“CD
EJECT’
will
be
displayed.)
Selecting a Track
Press
“TRACK
»»”
once
to
go
to
the
next
track.
Press
repeatedly
to
step
forward
through
all
the
tracks.
Press
“TRACK”
once
to
play
from
the
beginning
of
the
track
you
are
listening
to.
Press
twice
to
play
the
previous
track.
Press
repeatedly
to
step
backward
through
all
the
tracks.

Hold and Release
Press and Hold
Searching a Track
Press and hold “TRACK»™” or ““<TRACK” for more than a half
second to activate fast forward or reverse through a track.
Release “TRACK »»” or “««TRACK” to resume the normal CD play
from that position.
Repeating a Track
Press R/R» to repeat the current selection. “REP” indicator will light.
The current selection will continue to repeat until you press R/R»
again.
Random Selection
Press and hold R/R® for more than 2 seconds. “RAND” (DP875/
DP850EUC), “Rem” (DP830EUC) indicator will light. A random
selection of music is played from all available tracks.
To turn off the random play feature, press and hold R/R® again for
more than 2 seconds.
Scanning Tracks
Press SCAN. The display will blink and the first 10 seconds of each
track on the disc play in order.
To stop scanning and continue with the current track, press SCAN
again.
Selecting by Track Number
(Direct access)
Press a number from “1” to “6” then the corresponding track will
start.
e Press and hold a number from “7” to “12” (“1” to “6”) for more than
one second and the corresponding track will start.
CQ-DP875/850/830EUC
13

CD Changer Basics (only for ca-pps7sEuc)
DP675 40Wx4 CD PLAYER/RECEIVER WITH CHANGER CONTROL
m i
To start the CD Changer
With a disc magazine inserted in the CD Changer, press MODE. Play
stars from first track.
Selecting a Disc
Press
a
number
from
"1"
to
"6"
then
the
corresponding
Disc
wili
start.
Press
and
hold
a
number
from
"7"
to
"12"
("1"
to
"6"}
for
more
than
one
second
and
the
corresponding
Disc
will
start.
EA/RECEIVER WITH CHANGER CONTROL
Selecting a Track
Press
“TRACK"
once
to
go
to
the
next
track.
Press
repeatedly
to
step
forward
through
all
the
tracks.
Press
““
TRACK”
once
to
play
from
the
beginning
of
the
current
track.
Press
twice
to
play
the
previous
track.
Press
repeatedly
to
step
backward
through
all
the
tracks.
[Hold
and
Release
—
=
e
Hold
and
Release
Searching
a
Track
O
AO
P375
é0W-4
CD
PLAYERRECEIVER
WITH
Press
and
hold
“TRACK™”
or
"““
TRACK”
for
more
than
a
half
second
to
activate
fast
forward
or
reverse
through
a
track.
Release
“TRACKA”
or
““
TRACK”
to
resume
the
normal
CD
play
from
that
position.
Repeating a Track
Press R/R to repeat the current selection. “REP” indicator lights.
The
current
selection
continues
to
repeat
until
you
press
R/R»
again.
14
CQ-DP875/850/830EUC

Press and Hold
DP875 40W=4 CD
Random Selection
Press and hold R/R» for more than 2 seconds. “RAND” indicator will
light. À random selection of music is played from ail available tracks.
To turn off the random piay feature, press R/R again for more than
2 seconds.
Note:
+ If R/R® is pressed during random play, the track now in play
automatically returns to beginning upon coming to the end plays
back again. (Random repeat)
REP RAND
+ When R/R® is pressed again, repeat play stops and returns to
random play.
e Press and hold R/R > again, random play stops.
Scanning Tracks
Press SCAN. The display blinks and the first 10 seconds of each
track on the discs play in sequence.
To stop scanning and continue with the current track, press SCAN
again.
Scanning Discs
Press and hold DeSCAN for more than 2 seconds. The 1st track of all
the discs in the magazine is played for 10 seconds each. Also, Disc
Number is displayed at the same time. To stop the current play of the
disc scanning, press and hold DeSCAN for more than 2 seconds
again.
Changing the Display
Press DISP to switch the display in sequence as follows.
Disc / Track Number
Track Play Time
CQ-DP875/850/830EUC
15

Clock Basics (The clock system is 12-hours.)
o Z=zn-rOozm
DP875 40Wx4 CD PLAYER/RECEIVER WITH CHANGER CONTROL
{J MOTE
el
thse
Initial Time Seiting
@ Press DISP. “Adu” is displayed.
@ Press and hold DISP again for more
than 2 seconds, “12” blinks indicating
the time setting mode is activated.
OTo set hours, press ““ TUNE” or
“TUNEZ”.
| #
z=
DP875 40W:4 CD PLAYEI
|
@
Press
DISP
again
for
minute
setting.
H
® To set minutes, press "VTUNE” or
“TUNEA” .
Hold “A” or “v” to change numbers rapidly.
© When you have set the time, press DISP.
Resetting the Time
When
you
want
to
reset
the
time,
press
DISP
for
more
than
2
seconds
to
activate
the
time
setting
mode.
Then,
repeat
step
©
to
©
above.
Selecting the Clock Display
Press DISP for clock display.
Press
DISP
once
again,
the
current
audio
display
mode
resumes.
When
power
is
turned
off
while
the
time
is
displayed,
the
clock
mode
remains
on.
When
the
PWR
is
pressed
again,
the
system
is
completely.
Note:
Before
you
leave
your
car
that
has
no
ACC,
be
sure
to
switch
power
off.
16
CQ-DP875/850/830EUC

Programmed
Sound
Memory
¢ocospsrsoresceuc
Programmed Sound Memory Mode
Selection
A
desired
sound
setting
(except
for
VOL
and
ATT)
can
be
memorized
and
recalled.
Press
SDM
to
select
to
the
sound
memory
mode.
1) (NI TI
SOUND
eee
|
Programmed
Sound
Memory
Input
e
To
preset
sound
setting,
press
the
corresponding
preset
memory
button
(1
to
4)
for
more
than
2
seconds
at
sound
memory
mode.
VP ined Ti
GENINT uy
*
The
preset
memory
buttons,
5
and
6
are
not
valid
for
sound
memory.
Recall Programmed sound Memory
+
When
a
desired
preset
memory
button
is
pressed
in
sound
memory
mode,
the
corresponding
sound
setting
is
called.
Preset number
e The preset memory button 5 is recommended for setting
¢ The preset memory button 6 is used to release all sound settings.
To change to normal mode
+ Press MODE or SDM to return to the normal mode.
Note: When the sound memory mode is selected but no setting is
made within 5 seconds, the mode will return to the normal mode.
Level Meter
ge LUT Ae Aaa faa
E=
tocar
HAN
SAUT
Alt
PA
LS
te:
M
à
`
i
eae
pancreas
When
power
is
ON,
the
level
of
sound
sources,
such
as
radio
and
CD, is displayed.
R-ch sound Note: The level meter indications do not change when VOL, BAL, or
source level Other control is turned.
L-ch sound
source level
CQ-DP875/850/830EUC

u
18
Remote Control Unit Basics ror co-opsrspesoeuc)
Battery Replacement (Remote Control Unit)
1.Remove the battery holder.
Pull the holder by the Position B while pushing Position A in the
direction indicated by the arrow. Lithium battery
Rear view of remote
2.Replace the battery. control
Set a new battery properly with the (+) side up as illustrated.
3.Insert
the
battery
holder.
j
.
Push
in
the
holder
to
the full.
>
B
NAA
Notes on Batteries
Old batteries must immediately be removed and disposed.
Battery hoider Position A
Battery Information:
+ Designated Battery: Panasonic Lithium Battery (CR2025)
e Battery Life: 6 months with normal use (in normal room temperature)
Caution:
Improper use of batteries may cause overheating, explosion or ignition, resulting in injury or fire.
Battery leakage may cause damage to the unit.
+ Do not disassemble or short the batteries. Do not throw the batteries into the fire.
* To avoid the risk of accident, keep the batteries out of reach of children.
@® Power Button
@BAND/DISC UP Button
@ATT Button
@TUNE/TRACK Button
®Volume Control Button
© Mode Button
Please refer Battery Replacement before using
remote control.
Ope
rati
ng
Proced
ures
eae
controller
toward
the
sensor
of
Attenuator/Tone Enhancement
@ATT (ATT Button)
+ Press ATT to immediately decrease
Power
@POWER (Power Button)
Press POWER to switch on the power.
Press POWER again to switch off the power.
volume to about 1/10 of its previous level.
+ Press ATT again to resume the previous
volume.
Mode Selection
@MODE (Mode Button)
Press MODE to switch the operation
Volume
®VVOLA (Volume Control Button)
mode in the following order.
Radio ——» CD Player ——> CD Changer
Control
ney) ee
Press “A” or “V” to increase or decrease
volume level.
CQ-DP875/850/830EUC

Radio
Selecting a Band
@BAND (Band select Button)
Press BAND to select bands in sequence.
FM1 —> FM2 —> FM3 —> AM
Manual Tuning
@VTUNE® (Manual Tuning Button)
Press “V” or “A” to tune the frequency
downward or upward.
Compact Disc Player
(When a disc is inserted, playback starts.)
To starts CD Play
@MODE {MODE Button)
+ Only when a disc is inserted, press to
select CD play mode, and playback starts
automatically.
e When connecting with the CD changer,
press repeatedly to select the mode as
follows.
Radio ——> CD Player -—» CD Changer
Control
En AUX <—=———]
When a disc is inserted, the CD play starts
automatically regardless what mode you
are being listened.
CD Changer Control (Only for CQ-DP875EUC)
(In connection with the CD changer.)
Selecting a DISC
@DISC UP (Disc Select Button)
Press to sequentially advance to the next disc.
Selecting a Track
@®~VTRACKA (Track Select Button)
Press “^” once to go to the next track.
Press “Vv” once to play from the
beginning of the currently played track.
Press repeatedly to skip forward or
backward through ail the tracks.
Seek Tuning
@®VTUNEA (Seek Tuning Button)
Press and hold “Vv” or “A” for more than a
half second, then release. The radio will
automatically stop on the next station.
Selecting a Track
@VTRACKA (Track Select Button)
+ Press “A” once to go to the next track.
e Press “Vv” once to play from the
beginning of the currently played track.
e Press repeatedly to skip forward or
backward through all the tracks.
Searching a Track
@VTRACKA (Track Search Button)
* Press and hold “v” or “A” for more than a
half second to activate fast forward or
reverse through a track.
+ Release to stop fast forward or reverse.
Searching a Track
@VTRACKA (Track Search Button)
e Press and hold “v” or “A” for more than a
half second to activate fast forward or
reverse through the disc.
Release to stop fast forward or reverse.
CQ-DP875/850/830EUC
19

20
Installation Guide
ÁN WARNING
The installation information is designed for experienced installers and is not
intended for non-technical individuals. It does not contain warnings or cautions of
potential dangers in attempting to install this product.
Any attempt to install this product in a motor vehicle by anyone other than
qualified installer could cause damage to the electrical system and could result in
serious personal injury or death.
g Overview
This equipment should be installed by a
professional. However, if you plan to install this
unit yourself, your first step is to decide where to
install it. The instructions in these pages will
guide you through the remaining steps: (Piease
refer to “WARNING” statement above).
e Identify and label the vehicle wires
e Connect the vehicle wires to the wires of the
power connector
+ Install the unit in the dash
e Check the operation of the unit
If you do encounter problems, please consult
your nearest professional installer.
Caution: This unit will operate with a 12 volt DC
negative ground auto battery system only. Do not
attempt to use it in any other system. Doing so
could cause serious damage.
Before you begin installation, look for the
following items included in the packing with your
unit.
+ Warranty Card .... Fill this out promptly
+ MSC (in Canada: Panasonic) Servicenter
Directory ..... Keep for future reference in case
the unit needs servicing
° Installation Hardware ..... Needed for in-dash
installation
CQ-DP875/850/830EUC
O Installation Hardware
No.| tem =| Diagram |Qty|
Mounting Collar Sil
| Plain Washer (5 mm) | © |?
Spring Washer (5 mm) | 8 |?
Rear Support Strap
(6)
|
Hex.
Bolt
1
e (5 mmo x 25 mm) A
@) | Toothed Lock Washer Q 1
(5 mmo)
Mounting Bolt (5 mm) ean
ane 2a i”
Removable Face Plate 1
2 Case WA
a) | Remote Control Unit
(Only for CQ-DP875/850EUC)
Lithium battery 1
(Only for CO-DP875/850EUC)| C2
Dismounting Plate