Panasonic DVD-LX110EE User manual

Operating temperature
range: +5 to +35°C (+41 to +95°F)
Operating humidity range: 5-85% RH (no condensation)
Region number: Region No.3 (DVD-LX110GCS)
Region No.5 (DVD-LX110EE)
Discs played
[8cm (3”) or 12cm (5”)]:
DVD [DVD-Video, DVD-Audio, DivX
(EE only /*6, 8)]
DVD-RAM [DVD-VR, JPEG(*4,6,7),
MP3(*2,6), MPEG4(*5,6), DivX (EE
only /*6, 8)]
DVD-R [DVD-Video, DVD-VR,
JPEG(*4,6,7), MP3(*2,6),
MPEG4(*5,6), DivX (EE only /*6, 8)]
DVD-R DL (DVD-Video, DVD-VR)
DVD-RW [DVD-Video, DVD-
VR,JPEG(*4,6,7), MP3(*2,6),
MPEG4(*5,6), DivX (EE only /*6, 8)]
+R/RW (Video)
+R DL (Video)
CD, CD-R/RW [CD-DA, Video-CD,
SVCD(*1), MP3(*2, 6), WMA(*3, 6),
JPEG (*4,6,7), MPEG4(*5,6), DivX
(EE only /*6, 8), HighMAT Level 2
(Audio and Image)]
©2006 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
DVD-LX110EE
DVD-LX110GCS
RAE1907Z-C Mechanism Series
Colour
(S).................Silver Type
*1: Conforming to IEC62107
*2: MPEG-1 Layer3, MPEG-2 Layer3
*3: Windows Media Audio Ver9.0 L3.
Not compatible with Multiple Bit Rate
(MBR)
*4: Exif Ver 2.1 JPEG Baseline files
Picture resolution: between 160×120
and 6144×4096 pixels (sub sampling
is 4:0:0, 4:2:2, 4:2:0 or 4:4:4)
*5: MPEG4 data recorded with the
Panasonic SD multi cameras or DVD
recorders Conforming to SD VIDEO
specifications (ASF standard)/MPEG4
(Simple Profile) video system/G.726
audio system.
*6: The total combined maximum
number of recognizalbe audio, picture
and movie contents and groups:
4000 audio, picture and movie
contents and 400 groups.
*7: Extremely long and slender
pictures may not be displayed.
Portable DVD/CD PLAYER
Specifications
ORDER NO.CHM0606037CE

*8: Plays all versions of DivX® video
(including DivX®6) with standard
playback of DivX® media files.
Certified to the DivX Home Theater
Profile.
GMC (Global Motion Compensation)
is not supported.
Signal system: PAL 625/50 PAL 525/60 NTSC
LCD screen: 11” -Si, TFT wide-screen LCD
VGA 800 × 480 × RGB pixels
Composite-video output/
input:
Output/input level: 1Vp-p (75W)
Output/input terminal: Mini-jack ( 3.5mm)
Number of terminals: 1system (output/input selectable)
Audio output/input:
Output/input level: 1.5Vrms (1kHz, 0dB, 10kW)
Output/input terminal: Stereo mini-jack ( 3.5mm)
Number of terminals: 1system (output/input selectable)
Audio performance:
(1) Frequency response:
lDVD (linear audio): 4Hz-22kHz (48kHz sampling)
4Hz-44kHz (96kHz sampling)
lDVD-Audio: 4Hz-88kHz (192kHz sampling)
lCD audio: 4Hz-20kHz
(2) S/N ratio:
lCD audio: 115dB
(3) Dynamic range:
lDVD (linear audio): 98dB
lCD audio: 97dB
(4) Total harmonic distortion:
lCD audio: 0.008%
Digital audio output:
Optical digital output: Mini optical terminal
Number of terminals: 1system
(also used for audio output/ input)
SD Playback*1,5,6
Picture Playback: JPEG*2,3,7
Video Playback: MPEG4*2,4
*1 Useable memory capacities: 8MB, 16MB, 32MB, 64MB,
128MB, 256MB, 512MB, 1GB, 2GB
*2 Total maximum number of recognizable picture and video files
and folders
Picture: 4000 files and 398 folders
Video: 4000 files and 398 folders
*3 Extremely long and slender pictures may not be displayed.
*4 MPEG4 data recorded with the Panasonic SD multi cameras or
DVD recorders
Conforming to SD VIDEO specifications (ASF
standard)/MPEG4 (Simple Profile) video system/G.726 audio
system.
*5 SD card formatted with equipment conforming to SD File
System specifications Ver.1.01 such as Panasonic SD multi
cameras or DVD recorders (Conforming to FAT 12 standard
and FAT 16 standard)
*6 miniSDTM card is supported. (miniSDTM adaptor is required.)
*7 Conforming to SD Picture specifications
Picture resolution: between 160 × 120 and 6144 × 4096 pixels
(Sub sampling is 4:0:0, 4:2:0, 4:2:2 or 4:4:4)
Headphone output:
Output: Stereo mini-jack ( 3.5mm)
Number of terminals: 2systems
Battery duration
*CGR-H713: Option
*Room temperature
*using headphones
· When brightness is set to “-5”
while playing DVD 6 hours (CGR-
H713) / 3 hours (CGR-H712)
· When brightness is set to “0” while
playing DVD 4 hours (CGR-H713)
/ 2 hours (CGR-H712)
· When brightness is set to “+5”
while playing DVD 3 hours (CGR-
H713) / 1.5 hours (CGR-H712)
· When LCD panel is off while DVD
playing 12 hours (CGR-H713) / 6
hours (CGR-H712)
· When brightness is set to “-5”
while playing SD 7 hours (CGR-
H713) / 3.5 hours (CGR-H712)
· When brightness is set to “0” while
playing SD 5 hours (CGR-H713) /
2.5 hours (CGR-H712)
· When brightness is set to “+5”
while playing SD 4 hours (CGR-
H713) / 2 hours (CGR-H712)
· When LCD panel is off while SD
playing 18 hours (CGR-H713) / 9
hours (CGR-H712)
Battery recharge time
(at 20°C)
8 hours (CGR-H712) / 10 hours
(CGR-H713)
Pickup:
Wave length: 662nm/ 785nm (DVD/CD)
Laser power: CLASS 1M / CLASS 1M (DVD/CD)
Power supply: DC 12V (DC IN terminal) /
DC 7.2V (Exclusive battery terminal)
Power consumption
(Using included AC adaptor):
23W (Unit only: 20W)
Power consumption in
Standby mode
(Using included AC adaptor):
0.3W
Power consumption in
Recharge mode
(Using included AC adaptor):
13W
AC adaptor:
Power source:
A
C 110-240V, 50/60Hz
Power consumption: 36W
DC output: 12V, 2A
Car DC adaptor:
DC output: 12V 2A (Vehicle with 12V battery
only)
Battery pack CGR-H712
(lithium ion):
Voltage: 7.2V
Capacity: 4500mAh
2
DVD-LX110EE / DVD-LX110GCS

Dimensions (excluding
protrusions and battery):
287.6(W) × 216.0(D) × 50.3*(H) mm
[1121/64” (W) × 833/64” (D) × 2” (H)]
*30.5mm (113/64”) at lowest point
[D=221.7mm (823/32”) including
battery]
[H=55.3mm (23/16”) including battery]
Mass
(including battery): approximately 1875g (66.13 oz)
(without battery): approximately 1638g (57.77 oz)
solder:
This model uses lead free solder (PbF).
Note
Specifications are subject to change without notice.
Mass and dimensions are approximate.
Manufactured under license from Dolby Laboratories.
“Dolby“ and the double-D symbol are trademarks of Dolby
Laboratories.
“DTS“ and “DTS 2.0+ Digital Out” are trademarks of Digital Theater
Systems, Inc.
This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
1 Important Service Information 5
1.1. Notes 5
1.2. About DivX 5
1.3. Manual for Customer 6
2 SAFETY PRECAUTIONS 7
2.1. GENERAL GUIDELINES 7
3 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO
ELECTROSTATICALLY SENSITIVE (ES) DEVICES 7
4 PRECAUTION OF LASER DIODE 8
5 HOW TO REPLACE THE LITHIUM BATTERY 9
6 Service caution based on legal restrictions 10
6.1. General description about Lead Free Solder (PbF) 10
This product is licensed under the MPEG-4 Visual patent portfolio
license for the personal and noncommercial use of a consumer for
(i) encoding video in compliance with the MPEG-4 Visual Standard
(“MPEG-4 Video”) and/or (ii) decoding MPEG-4 Video that was
encoded by a consumer engaged in a personal and non-
commercial activity and/or was obtained from a video provider
licensed by MPEG LA to provide MPEG-4 Video.
No license is granted or shall be implied for any other use.
A
dditional information including that relating to promotional, internal
and commercial uses and licensing may be obtained from MPEG
LA, LLC. See http://www.mpegla.com.
Portions of this product are protected under copyright law and are
provided under license by ARIS/SOLANA/4C.
7 HANDLING PRECAUTIONS FOR TRAVERSE DECK 11
7.1. Handling of optical pickup 11
7.2. Grounding for electrostatic breakdown prevention 11
8 DISASSEMBLY, REASSEMBLY AND SERVICE POSITION 12
8.1. Disassembly 13
8.2. P.C.B. location 14
8.3. Main cabinet of the unit 15
8.4. Traverse assembly 16
8.5. Optical pick-up unit 17
8.6. Disc motor 17
8.7. Main P.C.B. 18
8.8. Front SW P.C.B. 18
CONTENTS
Page Page
3
DVD-LX110EE / DVD-LX110GCS

8.9. SD card P.C.B. 18
8.10. Side SW P.C.B. 18
8.11. Monitor assembly 19
8.12. Disc cover 19
8.13. Monitor cover 20
8.14. Mono arm 21
8.15. LCD I/F P.C.B. 22
8.16. LCD panel and inverter unit 22
8.17. Replacing the fuse in the car dc adaptor 22
8.18. Service position 23
9 SELF-DIAGNOSIS FUNCTION AND SERVICE MODE 24
9.1. Optical Pickup Breakdown Diagnosis 24
9.2. UHF displays 25
9.3. Service Mode Table 1 26
9.4. DVD Self Diagnostic Function-Error Code 26
9.5. Last Error Code saved during NO PLAY 28
9.6. Service mode table 28
9.7. Lens cleaning 30
10 SERVICE PRECAUTIONS 31
10.1. Recovery after the dvd player is repaired 31
10.2. Firmware version-up of the DVD player 31
11 ADJUSTMENT PROCEDURES 32
11.1. Service Tools and Equipment 32
11.2. Important points in adjustment 32
11.3. Storing and Handling Test Discs 32
11.4. Optical adjustment 33
11.5. Electrical adjustment (LCD) 35
11.6. Electrical check (Video output check) 36
12 Abbreviations 37
13 VOLTAGE CHART 39
13.1. MAIN P.C.B. 39
13.2. LCD P.C.B. 43
14 BLOCK DIAGRAM 45
14.1. OVERALL BLOCK DIAGRAM 45
14.2. POWER SUPPLY BLOCK DIAGRAM 46
14.3. SERVO BLOCK DIAGRAM 47
14.4. VIDEO BLOCK DIAGRAM 48
14.5. AUDIO BLOCK DIAGRAM 49
14.6. LCD DRIVE BLOCK DIAGRAM 51
15 INTERCONNECTION SCHEMATIC DIAGRAM & SCHEMATIC
DIAGRAM NOTES 53
15.1. INTERCONNECTION SCHEMATIC DIAGRAM 53
15.2. SCHEMATIC DIAGRAM NOTES 54
16 SCHEMATIC DIAGRAM 55
16.1. POWER SUPPLY/CHARGE BATTERY SECTION (MAIN
P.C.B. (1/4)) SCHEMATIC DIAGRAM 55
16.2. OPTICAL PICK UP/SERVO/OPERATION SECTION
(MAIN P.C.B. (2/4)) SCHEMATIC DIAGRAM 56
16.3. DV3 SECTION (MAIN P.C.B. (3/4)) SCHEMATIC
DIAGRAM 57
16.4. AUDIO OUT/VIDEO OUT SECTION (MAIN P.C.B. (4/4))
SCHEMATIC DIAGRAM 58
16.5. LCD IF SCHEMATIC DIAGRAM 59
16.6. LCD PAL SECTION (LCD P.C.B. (2/2)) SCHEMATIC
DIAGRAM 63
16.7. SIDE SW SCHEMATIC DIAGRAM 64
16.8. FRONT SW SCHEMATIC DIAGRAM 65
16.9. SD CARD SCHEMATIC DIAGRAM 66
16.10. IR & BATTERY JACK SCHEMATIC DIAGRAM 67
17 CIRCUIT BOARD ASSEMBLY 69
17.1. MAIN P.C.B. (1/2) (COMPONENT SIDE) 69
17.2. MAIN P.C.B. (2/2) (FOIL SIDE) 70
17.3. LCD P.C.B. 71
17.4. SIDE SW P.C.B. , FRONT SW P.C.B. , SD CARD P.C.B.
, IR P.C.B. & BATTERY JACK P.C.B. 72
18 EXPLODED VIEWS 73
18.1. Casing Parts & Mechanism Section Exploded View 73
18.2. Mechanism Section Exploded View 74
18.3. Packing & Accessories Exploded View 75
19 REPLACEMENT PARTS LIST 76
4
DVD-LX110EE / DVD-LX110GCS

1 Important Service Information
1.1. Notes
When you replace EEPROM or exchange MAIN PCB, you have to take “Manual for customer” to the customer with unit. (also in
the case of unit exchanges)
Please take and use “Manual for customer” from below.
1. Come with MAIN PCB or EEPROM (Service part).
2. Make a photocopy section 1.3. “Manual for customer” on this service manual.
“Manual for customer” has important information for “DivX Video-on-Demand Service” user.
Please don’t forget take it to the customer with unit!
1.2. About DivX
1.2.1. DivX
A video compression format developed by DivXNetworks, Inc. that compresses video files without any considerable loss of video
quality.
1.2.2. About DivX Video-on-Demand Content
5
DVD-LX110EE / DVD-LX110GCS

1.3. Manual for Customer
1. The registration code has been changed for the repair of the product or the product
exchange.
2. Obtain and register a new registration code, otherwise you will no longer be able to
play DivXVideo-on-Demand content.
3. Follow the procedure on the DivX Video-on-Demand web site to register at
http://vod.divx.com/.
* If you do not use the DivX Video-on-Demand content, please ignore this warning.
Warning for CustomersWho Use the DivXVideo-on-Demand content.
6
DVD-LX110EE / DVD-LX110GCS

2.1.1. LEAKAGE CURRENT COLD
CHECK
1. Unplug the AC cord and connect a jumper between the two
prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between
the jumpered AC plug and each exposed metallic cabinet
part on the equipment such as screwheads, connectors,
control shafts, etc. When the exposed metallic part has a
return path to the chassis, the reading should be between
1MWand 5.2MW.
When the exposed metal does not have a return path to
the chassis, the reading must be .
2.1.2. LEAKAGE CURRENT HOT CHECK
1. Plug the AC cord directly into the AC outlet. Do not use an
isolation transformer for this check.
2. Connect a 1.5kW, 10 watts resistor, in parallel with a 0.15µF
capacitors, between each exposed metallic part on the set
and a good earth ground such as a water pipe.
3. Use an AC voltmeter, with 1000 ohms/volt or more
sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the
above measurements.
6. The potential at any point should not exceed 0.75 volts
RMS. A leakage current tester (Simpson Model 229 or
equivalent) may be used to make the hot checks, leakage
current must not exceed 1/2 milliamp. In case a
measurement is outside of the limits specified, there is a
possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the
customer.
2 SAFETY PRECAUTIONS
2.1. GENERAL GUIDELINES
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
3 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD)
TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum
foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparable
conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
7
DVD-LX110EE / DVD-LX110GCS

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to
damage an ES device).
4 PRECAUTION OF LASER DIODE
8
DVD-LX110EE / DVD-LX110GCS

5 HOW TO REPLACE THE LITHIUM BATTERY
This model is using a lithium battery for the remote control ass’y.
NOTE:
The lithium battery is a critical component. ( Type No.: CR2025 Manufactured by Panasonic. )
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in equipment designed specifically for its use.
Replacement batteries must be of the same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
9
DVD-LX110EE / DVD-LX110GCS

6 Service caution based on legal restrictions
6.1. General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86 F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
The letter of “PbF” is printed either foil side or components side on the PCB
using the lead free solder. (See right figure)
Service caution for repair work using Lead Free Solder (PbF)
- The lead free solder has to be used when repairing the equipment for which the lead free solder is used.(Definition: The letter
of "PbF" is printed on the PCB using the lead free solder.)
- To put lead free solder, it should be well molten and mixed with the original lead free solder.
- Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
- Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
- Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350+-30
degrees C (662+-86 F).
Recommended Lead Free Solder (Service Parts Route.)
- The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
10
DVD-LX110EE / DVD-LX110GCS

The laser diode in the optical pickup may break down due to
potential difference caused by static electricity of clothes or
human body.
So be careful of electrostatic break down during repair of the
optical pickup.
7.1. Handling of optical pickup
1. Do not subject the optical pickup to static electricity as it is
extremely sensitive to electrical shock.
2. To prevent the breakdown of the laser diode, an antistatic
shorting pin is inserted into the flexible board (FPC Board).
When removing or connecting the short pin, finish the job in
as short times as possible.
3. Be careful not to apply excessive stress to the flexible board
(FPC Board).
4. Do not turn the variable resistor (Laser power adjustment).
1. Human body grounding
Use the antistatic wrist strap to discharge the static
electricity from your body.
2. Work table grounding
Put a conductive material (sheet) or steel sheet on the area
where the optical pickup is placed and ground the sheet.
Caution
The static electricity of your clothes will not be grounded
through the wrist strap. So take care not to let your
clothes touch the optical pickup.
It has already been adjusted.
7 HANDLING PRECAUTIONS FOR TRAVERSE DECK
7.2. Grounding for electrostatic breakdown prevention
11
DVD-LX110EE / DVD-LX110GCS

8 DISASSEMBLY, REASSEMBLY AND SERVICE POSITION
12
DVD-LX110EE / DVD-LX110GCS

8.1. Disassembly
13
DVD-LX110EE / DVD-LX110GCS

8.2. P.C.B. location
14
DVD-LX110EE / DVD-LX110GCS

8.3. Main cabinet of the unit
<Removing battery pack>
Release the lock lever and remove the battery pack in the
direction of the arrow.
1. Remove the 16 screws from the bottom of the unit.
2. Release the latches and remove the bottom cabinet.
15
DVD-LX110EE / DVD-LX110GCS

8.4. Traverse assembly
8.4.1. Removing traverse assembly
1. Solder the 2 laser short lands on the flexible cable.
2. Unlock the connectors and remove the flexible cables.
8.4.2. Reinstalling traverse assembly
1. Reinstall the traverse assembly to the specified pin of the
unit.
2. Reinstall the flexible cable of the optical pickpup unit and
lock it securely.
3. Remove the solder of each laser short land of the flexible
cable.
Caution:
Remove the solders completely: otherwise the laser
diode won´t emit light.
4. Reinstall the spindle flexible cable as shown figure.
16
DVD-LX110EE / DVD-LX110GCS

8.5. Optical pick-up unit
8.5.1. Removing optical pick-up unit
Make sure that the traverse assembly removed before trying to
remove the optical pick-up unit.
When removing the traverse assembly, solder the two laser
short lands on the flexible cable of the optical pick-up unit.
1. Remove the two screws securing the main shaft retainer.
2. Remove the main shaft retainer.
3. Slide the main shaft in the direction indicated by the arrow
to remove the optical pick-up unit.
8.5.2. Reinstalling optical pick-up unit
The optical pick-up unit is factory adjusted. Do not touch the
adjustment screw.
1. Reassemble the disassembled parts in the reverse order of
disassembly.
2. When reinstalling the traverse assembly on the main unit
after installing the optical pick-up unit, make sure to remove
the solder from each of the two laser short lands on the
flexible cable.
Caution:
· Remove the solders completely; otherwise the laser
diode won’t emit light.
· After replacing the optical pick-up unit, check the quality
of images played back and make optical adjustment.
8.6. Disc motor
8.6.1. Removing disc motor
1. Remove the adjustment screws A, B, and C.
2. Remove the disc motor.
8.6.2. Caution to be taken when
replacing the disc motor
1. The mounting screws of the disc motor also serve as
adjustment screws. When reinstalling the disc motor, first
turn the screws A, B, and C as far as they go by usual force
to secure them (do not overtighten).
2. Back off the adjustment screws A and C two complete turns
and secure them.
3. Back off the adjustment screw B one and a half turns and
secure them.
· This makes it nearly possible to play back disks and
adjust the jitter.
· Thereafter, adjust the adjustment screws C and A as
indicated.
17
DVD-LX110EE / DVD-LX110GCS

8.7. Main P.C.B.
1. Remove the 4 connectors.
2. Remove the 7 screws and remove the main P.C.B., battery
jack P.C.B. and speakers.
8.8. Front SW P.C.B.
1. Remove the connector.
2. Remove the 4 screws and remove the front SW P.C.B. and
IR P.C.B..
8.9. SD card P.C.B.
1. Remove the connector.
2. Remove the 3 screws and remove the SD card P.C.B..
8.10. Side SW P.C.B.
1. Remove the connector.
2. Remove the 2 screws and remove the side SW P.C.B..
18
DVD-LX110EE / DVD-LX110GCS

8.11. Monitor assembly
1. Remove the connector.
2. Remove the 5 screws.
1. Release the latches and remove the hinge cover.
2. Remove the monitor assembly.
<Caution to be taken when installing monitor assembly>
1. Install the hinge shaft holder on the cabinet as shown
figure.
8.12. Disc cover
1. Remove the screw and remove the hinge angle.
19
DVD-LX110EE / DVD-LX110GCS

2. Remove the spring into the direction of the arrow.
3. Remove the 2 screws and remove the disc hinge cover.
4. Remove the stopper piece into the direction of the arrow.
5. Remove the shaft into the direction of the arrow.
Caution:
Please don´t lose the spring
8.13. Monitor cover
1. Remove the 8 screws
2. Remove the monitor cover into the direction of the arrow.
3. Remove the 2 connectors.
20
DVD-LX110EE / DVD-LX110GCS